Merge remote-tracking branch 'wireless-next/master' into HEAD

Merge to get the wil6210 changes that a cfg80211 change needs.
A conflict in drivers/net/wireless/ath/ath9k/init.c was just
whitespace changes.

Also fix a semantic conflict due to cw1200 using WoWLAN which
I had modified in my tree.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

1 files changed, 51 insertions, 6 deletions

diff --git a/drivers/net/wireless/iwlwifi/dvm/dev.h b/drivers/net/wireless/iwlwifi/dvm/dev.h
index e71acfd344aa..5cd87f949266 100644
--- a/drivers/net/wireless/iwlwifi/dvm/dev.h
+++ b/drivers/net/wireless/iwlwifi/dvm/dev.h
@@ -568,16 +568,61 @@ struct iwl_hw_params {
 	const struct iwl_sensitivity_ranges *sens;
 };
 
-struct iwl_lib_ops {
-	/* set hw dependent parameters */
+/**
+ * struct iwl_dvm_bt_params - DVM specific BT (coex) parameters
+ * @advanced_bt_coexist: support advanced bt coexist
+ * @bt_init_traffic_load: specify initial bt traffic load
+ * @bt_prio_boost: default bt priority boost value
+ * @agg_time_limit: maximum number of uSec in aggregation
+ * @bt_sco_disable: uCode should not response to BT in SCO/ESCO mode
+ */
+struct iwl_dvm_bt_params {
+	bool advanced_bt_coexist;
+	u8 bt_init_traffic_load;
+	u32 bt_prio_boost;
+	u16 agg_time_limit;
+	bool bt_sco_disable;
+	bool bt_session_2;
+};
+
+/**
+ * struct iwl_dvm_cfg - DVM firmware specific device configuration
+ * @set_hw_params: set hardware parameters
+ * @set_channel_switch: send channel switch command
+ * @nic_config: apply device specific configuration
+ * @temperature: read temperature
+ * @adv_thermal_throttle: support advance thermal throttle
+ * @support_ct_kill_exit: support ct kill exit condition
+ * @plcp_delta_threshold: plcp error rate threshold used to trigger
+ *	radio tuning when there is a high receiving plcp error rate
+ * @chain_noise_scale: default chain noise scale used for gain computation
+ * @hd_v2: v2 of enhanced sensitivity value, used for 2000 series and up
+ * @no_idle_support: do not support idle mode
+ * @bt_params: pointer to BT parameters
+ * @need_temp_offset_calib: need to perform temperature offset calibration
+ * @no_xtal_calib: some devices do not need crystal calibration data,
+ *	don't send it to those
+ * @temp_offset_v2: support v2 of temperature offset calibration
+ * @adv_pm: advanced power management
+ */
+struct iwl_dvm_cfg {
 	void (*set_hw_params)(struct iwl_priv *priv);
 	int (*set_channel_switch)(struct iwl_priv *priv,
 				  struct ieee80211_channel_switch *ch_switch);
-	/* device specific configuration */
 	void (*nic_config)(struct iwl_priv *priv);
-
-	/* temperature */
 	void (*temperature)(struct iwl_priv *priv);
+
+	const struct iwl_dvm_bt_params *bt_params;
+	s32 chain_noise_scale;
+	u8 plcp_delta_threshold;
+	bool adv_thermal_throttle;
+	bool support_ct_kill_exit;
+	bool hd_v2;
+	bool no_idle_support;
+	bool need_temp_offset_calib;
+	bool no_xtal_calib;
+	bool temp_offset_v2;
+	bool adv_pm;
 };
 
 struct iwl_wipan_noa_data {
@@ -610,7 +655,7 @@ struct iwl_priv {
 	struct device *dev;		/* for debug prints only */
 	const struct iwl_cfg *cfg;
 	const struct iwl_fw *fw;
-	const struct iwl_lib_ops *lib;
+	const struct iwl_dvm_cfg *lib;
 	unsigned long status;
 
 	spinlock_t sta_lock;