spi: Introduce new driver for Qualcomm QuadSPI controller

New driver for Qualcomm QuadSPI(QSPI) controller that is used to
communicate with slaves such as flash memory devices. The QSPI controller
can operate in 2 or 4 wire mode but only supports SPI Mode 0. The
controller can also operate in Single or Dual data rate modes.

Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

3 files changed, 588 insertions, 0 deletions

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index e6b430890f7a..881d499c69b2 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -520,6 +520,12 @@ config SPI_RSPI
 	help
 	  SPI driver for Renesas RSPI and QSPI blocks.
 
+config SPI_QCOM_QSPI
+	tristate "QTI QSPI controller"
+	depends on ARCH_QCOM
+	help
+	  QSPI(Quad SPI) driver for Qualcomm QSPI controller.
+
 config SPI_QUP
 	tristate "Qualcomm SPI controller with QUP interface"
 	depends on ARCH_QCOM || (ARM && COMPILE_TEST)
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 644b22ecb4b1..0eb8b185d8e5 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -74,6 +74,7 @@ obj-$(CONFIG_SPI_PPC4xx)		+= spi-ppc4xx.o
 spi-pxa2xx-platform-objs		:= spi-pxa2xx.o spi-pxa2xx-dma.o
 obj-$(CONFIG_SPI_PXA2XX)		+= spi-pxa2xx-platform.o
 obj-$(CONFIG_SPI_PXA2XX_PCI)		+= spi-pxa2xx-pci.o
+obj-$(CONFIG_SPI_QCOM_QSPI)		+= spi-qcom-qspi.o
 obj-$(CONFIG_SPI_QUP)			+= spi-qup.o
 obj-$(CONFIG_SPI_ROCKCHIP)		+= spi-rockchip.o
 obj-$(CONFIG_SPI_RB4XX)			+= spi-rb4xx.o
diff --git a/drivers/spi/spi-qcom-qspi.c b/drivers/spi/spi-qcom-qspi.c
new file mode 100644
index 000000000000..b8163b40bb92
--- /dev/null
+++ b/drivers/spi/spi-qcom-qspi.c
@@ -0,0 +1,581 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017-2018, The Linux foundation. All rights reserved.
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pm_runtime.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+
+#define QSPI_NUM_CS		2
+#define QSPI_BYTES_PER_WORD	4
+
+#define MSTR_CONFIG		0x0000
+#define FULL_CYCLE_MODE		BIT(3)
+#define FB_CLK_EN		BIT(4)
+#define PIN_HOLDN		BIT(6)
+#define PIN_WPN			BIT(7)
+#define DMA_ENABLE		BIT(8)
+#define BIG_ENDIAN_MODE		BIT(9)
+#define SPI_MODE_MSK		0xc00
+#define SPI_MODE_SHFT		10
+#define CHIP_SELECT_NUM		BIT(12)
+#define SBL_EN			BIT(13)
+#define LPA_BASE_MSK		0x3c000
+#define LPA_BASE_SHFT		14
+#define TX_DATA_DELAY_MSK	0xc0000
+#define TX_DATA_DELAY_SHFT	18
+#define TX_CLK_DELAY_MSK	0x300000
+#define TX_CLK_DELAY_SHFT	20
+#define TX_CS_N_DELAY_MSK	0xc00000
+#define TX_CS_N_DELAY_SHFT	22
+#define TX_DATA_OE_DELAY_MSK	0x3000000
+#define TX_DATA_OE_DELAY_SHFT	24
+
+#define AHB_MASTER_CFG				0x0004
+#define HMEM_TYPE_START_MID_TRANS_MSK		0x7
+#define HMEM_TYPE_START_MID_TRANS_SHFT		0
+#define HMEM_TYPE_LAST_TRANS_MSK		0x38
+#define HMEM_TYPE_LAST_TRANS_SHFT		3
+#define USE_HMEMTYPE_LAST_ON_DESC_OR_CHAIN_MSK	0xc0
+#define USE_HMEMTYPE_LAST_ON_DESC_OR_CHAIN_SHFT	6
+#define HMEMTYPE_READ_TRANS_MSK			0x700
+#define HMEMTYPE_READ_TRANS_SHFT		8
+#define HSHARED					BIT(11)
+#define HINNERSHARED				BIT(12)
+
+#define MSTR_INT_EN		0x000C
+#define MSTR_INT_STATUS		0x0010
+#define RESP_FIFO_UNDERRUN	BIT(0)
+#define RESP_FIFO_NOT_EMPTY	BIT(1)
+#define RESP_FIFO_RDY		BIT(2)
+#define HRESP_FROM_NOC_ERR	BIT(3)
+#define WR_FIFO_EMPTY		BIT(9)
+#define WR_FIFO_FULL		BIT(10)
+#define WR_FIFO_OVERRUN		BIT(11)
+#define TRANSACTION_DONE	BIT(16)
+#define QSPI_ERR_IRQS		(RESP_FIFO_UNDERRUN | HRESP_FROM_NOC_ERR | \
+				 WR_FIFO_OVERRUN)
+#define QSPI_ALL_IRQS		(QSPI_ERR_IRQS | RESP_FIFO_RDY | \
+				 WR_FIFO_EMPTY | WR_FIFO_FULL | \
+				 TRANSACTION_DONE)
+
+#define PIO_XFER_CTRL		0x0014
+#define REQUEST_COUNT_MSK	0xffff
+
+#define PIO_XFER_CFG		0x0018
+#define TRANSFER_DIRECTION	BIT(0)
+#define MULTI_IO_MODE_MSK	0xe
+#define MULTI_IO_MODE_SHFT	1
+#define TRANSFER_FRAGMENT	BIT(8)
+#define SDR_1BIT		1
+#define SDR_2BIT		2
+#define SDR_4BIT		3
+#define DDR_1BIT		5
+#define DDR_2BIT		6
+#define DDR_4BIT		7
+#define DMA_DESC_SINGLE_SPI	1
+#define DMA_DESC_DUAL_SPI	2
+#define DMA_DESC_QUAD_SPI	3
+
+#define PIO_XFER_STATUS		0x001c
+#define WR_FIFO_BYTES_MSK	0xffff0000
+#define WR_FIFO_BYTES_SHFT	16
+
+#define PIO_DATAOUT_1B		0x0020
+#define PIO_DATAOUT_4B		0x0024
+
+#define RD_FIFO_STATUS	0x002c
+#define FIFO_EMPTY	BIT(11)
+#define WR_CNTS_MSK	0x7f0
+#define WR_CNTS_SHFT	4
+#define RDY_64BYTE	BIT(3)
+#define RDY_32BYTE	BIT(2)
+#define RDY_16BYTE	BIT(1)
+#define FIFO_RDY	BIT(0)
+
+#define RD_FIFO_CFG		0x0028
+#define CONTINUOUS_MODE		BIT(0)
+
+#define RD_FIFO_RESET		0x0030
+#define RESET_FIFO		BIT(0)
+
+#define CUR_MEM_ADDR		0x0048
+#define HW_VERSION		0x004c
+#define RD_FIFO			0x0050
+#define SAMPLING_CLK_CFG	0x0090
+#define SAMPLING_CLK_STATUS	0x0094
+
+
+enum qspi_dir {
+	QSPI_READ,
+	QSPI_WRITE,
+};
+
+struct qspi_xfer {
+	union {
+		const void *tx_buf;
+		void *rx_buf;
+	};
+	unsigned int rem_bytes;
+	unsigned int buswidth;
+	enum qspi_dir dir;
+	bool is_last;
+};
+
+enum qspi_clocks {
+	QSPI_CLK_CORE,
+	QSPI_CLK_IFACE,
+	QSPI_NUM_CLKS
+};
+
+struct qcom_qspi {
+	void __iomem *base;
+	struct device *dev;
+	struct clk_bulk_data clks[QSPI_NUM_CLKS];
+	struct qspi_xfer xfer;
+	/* Lock to protect data accessed by IRQs */
+	spinlock_t lock;
+};
+
+static u32 qspi_buswidth_to_iomode(struct qcom_qspi *ctrl,
+				   unsigned int buswidth)
+{
+	switch (buswidth) {
+	case 1:
+		return SDR_1BIT << MULTI_IO_MODE_SHFT;
+	case 2:
+		return SDR_2BIT << MULTI_IO_MODE_SHFT;
+	case 4:
+		return SDR_4BIT << MULTI_IO_MODE_SHFT;
+	default:
+		dev_warn_once(ctrl->dev,
+				"Unexpected bus width: %u\n", buswidth);
+		return SDR_1BIT << MULTI_IO_MODE_SHFT;
+	}
+}
+
+static void qcom_qspi_pio_xfer_cfg(struct qcom_qspi *ctrl)
+{
+	u32 pio_xfer_cfg;
+	const struct qspi_xfer *xfer;
+
+	xfer = &ctrl->xfer;
+	pio_xfer_cfg = readl(ctrl->base + PIO_XFER_CFG);
+	pio_xfer_cfg &= ~TRANSFER_DIRECTION;
+	pio_xfer_cfg |= xfer->dir;
+	if (xfer->is_last)
+		pio_xfer_cfg &= ~TRANSFER_FRAGMENT;
+	else
+		pio_xfer_cfg |= TRANSFER_FRAGMENT;
+	pio_xfer_cfg &= ~MULTI_IO_MODE_MSK;
+	pio_xfer_cfg |= qspi_buswidth_to_iomode(ctrl, xfer->buswidth);
+
+	writel(pio_xfer_cfg, ctrl->base + PIO_XFER_CFG);
+}
+
+static void qcom_qspi_pio_xfer_ctrl(struct qcom_qspi *ctrl)
+{
+	u32 pio_xfer_ctrl;
+
+	pio_xfer_ctrl = readl(ctrl->base + PIO_XFER_CTRL);
+	pio_xfer_ctrl &= ~REQUEST_COUNT_MSK;
+	pio_xfer_ctrl |= ctrl->xfer.rem_bytes;
+	writel(pio_xfer_ctrl, ctrl->base + PIO_XFER_CTRL);
+}
+
+static void qcom_qspi_pio_xfer(struct qcom_qspi *ctrl)
+{
+	u32 ints;
+
+	qcom_qspi_pio_xfer_cfg(ctrl);
+
+	/* Ack any previous interrupts that might be hanging around */
+	writel(QSPI_ALL_IRQS, ctrl->base + MSTR_INT_STATUS);
+
+	/* Setup new interrupts */
+	if (ctrl->xfer.dir == QSPI_WRITE)
+		ints = QSPI_ERR_IRQS | WR_FIFO_EMPTY;
+	else
+		ints = QSPI_ERR_IRQS | RESP_FIFO_RDY;
+	writel(ints, ctrl->base + MSTR_INT_EN);
+
+	/* Kick off the transfer */
+	qcom_qspi_pio_xfer_ctrl(ctrl);
+}
+
+static void qcom_qspi_handle_err(struct spi_master *master,
+				 struct spi_message *msg)
+{
+	struct qcom_qspi *ctrl = spi_master_get_devdata(master);
+	unsigned long flags;
+
+	spin_lock_irqsave(&ctrl->lock, flags);
+	writel(0, ctrl->base + MSTR_INT_EN);
+	ctrl->xfer.rem_bytes = 0;
+	spin_unlock_irqrestore(&ctrl->lock, flags);
+}
+
+static int qcom_qspi_transfer_one(struct spi_master *master,
+				  struct spi_device *slv,
+				  struct spi_transfer *xfer)
+{
+	struct qcom_qspi *ctrl = spi_master_get_devdata(master);
+	int ret;
+	unsigned long speed_hz;
+	unsigned long flags;
+
+	speed_hz = slv->max_speed_hz;
+	if (xfer->speed_hz)
+		speed_hz = xfer->speed_hz;
+
+	/* In regular operation (SBL_EN=1) core must be 4x transfer clock */
+	ret = clk_set_rate(ctrl->clks[QSPI_CLK_CORE].clk, speed_hz * 4);
+	if (ret) {
+		dev_err(ctrl->dev, "Failed to set core clk %d\n", ret);
+		return ret;
+	}
+
+	spin_lock_irqsave(&ctrl->lock, flags);
+
+	/* We are half duplex, so either rx or tx will be set */
+	if (xfer->rx_buf) {
+		ctrl->xfer.dir = QSPI_READ;
+		ctrl->xfer.buswidth = xfer->rx_nbits;
+		ctrl->xfer.rx_buf = xfer->rx_buf;
+	} else {
+		ctrl->xfer.dir = QSPI_WRITE;
+		ctrl->xfer.buswidth = xfer->tx_nbits;
+		ctrl->xfer.tx_buf = xfer->tx_buf;
+	}
+	ctrl->xfer.is_last = list_is_last(&xfer->transfer_list,
+					  &master->cur_msg->transfers);
+	ctrl->xfer.rem_bytes = xfer->len;
+	qcom_qspi_pio_xfer(ctrl);
+
+	spin_unlock_irqrestore(&ctrl->lock, flags);
+
+	/* We'll call spi_finalize_current_transfer() when done */
+	return 1;
+}
+
+static int qcom_qspi_prepare_message(struct spi_master *master,
+				     struct spi_message *message)
+{
+	u32 mstr_cfg;
+	struct qcom_qspi *ctrl;
+	int tx_data_oe_delay = 1;
+	int tx_data_delay = 1;
+	unsigned long flags;
+
+	ctrl = spi_master_get_devdata(master);
+	spin_lock_irqsave(&ctrl->lock, flags);
+
+	mstr_cfg = readl(ctrl->base + MSTR_CONFIG);
+	mstr_cfg &= ~CHIP_SELECT_NUM;
+	if (message->spi->chip_select)
+		mstr_cfg |= CHIP_SELECT_NUM;
+
+	mstr_cfg |= FB_CLK_EN | PIN_WPN | PIN_HOLDN | SBL_EN | FULL_CYCLE_MODE;
+	mstr_cfg &= ~(SPI_MODE_MSK | TX_DATA_OE_DELAY_MSK | TX_DATA_DELAY_MSK);
+	mstr_cfg |= message->spi->mode << SPI_MODE_SHFT;
+	mstr_cfg |= tx_data_oe_delay << TX_DATA_OE_DELAY_SHFT;
+	mstr_cfg |= tx_data_delay << TX_DATA_DELAY_SHFT;
+	mstr_cfg &= ~DMA_ENABLE;
+
+	writel(mstr_cfg, ctrl->base + MSTR_CONFIG);
+	spin_unlock_irqrestore(&ctrl->lock, flags);
+
+	return 0;
+}
+
+static irqreturn_t pio_read(struct qcom_qspi *ctrl)
+{
+	u32 rd_fifo_status;
+	u32 rd_fifo;
+	unsigned int wr_cnts;
+	unsigned int bytes_to_read;
+	unsigned int words_to_read;
+	u32 *word_buf;
+	u8 *byte_buf;
+	int i;
+
+	rd_fifo_status = readl(ctrl->base + RD_FIFO_STATUS);
+
+	if (!(rd_fifo_status & FIFO_RDY)) {
+		dev_dbg(ctrl->dev, "Spurious IRQ %#x\n", rd_fifo_status);
+		return IRQ_NONE;
+	}
+
+	wr_cnts = (rd_fifo_status & WR_CNTS_MSK) >> WR_CNTS_SHFT;
+	wr_cnts = min(wr_cnts, ctrl->xfer.rem_bytes);
+
+	words_to_read = wr_cnts / QSPI_BYTES_PER_WORD;
+	bytes_to_read = wr_cnts % QSPI_BYTES_PER_WORD;
+
+	if (words_to_read) {
+		word_buf = ctrl->xfer.rx_buf;
+		ctrl->xfer.rem_bytes -= words_to_read * QSPI_BYTES_PER_WORD;
+		ioread32_rep(ctrl->base + RD_FIFO, word_buf, words_to_read);
+		ctrl->xfer.rx_buf = word_buf + words_to_read;
+	}
+
+	if (bytes_to_read) {
+		byte_buf = ctrl->xfer.rx_buf;
+		rd_fifo = readl(ctrl->base + RD_FIFO);
+		ctrl->xfer.rem_bytes -= bytes_to_read;
+		for (i = 0; i < bytes_to_read; i++)
+			*byte_buf++ = rd_fifo >> (i * BITS_PER_BYTE);
+		ctrl->xfer.rx_buf = byte_buf;
+	}
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t pio_write(struct qcom_qspi *ctrl)
+{
+	const void *xfer_buf = ctrl->xfer.tx_buf;
+	const int *word_buf;
+	const char *byte_buf;
+	unsigned int wr_fifo_bytes;
+	unsigned int wr_fifo_words;
+	unsigned int wr_size;
+	unsigned int rem_words;
+
+	wr_fifo_bytes = readl(ctrl->base + PIO_XFER_STATUS);
+	wr_fifo_bytes >>= WR_FIFO_BYTES_SHFT;
+
+	if (ctrl->xfer.rem_bytes < QSPI_BYTES_PER_WORD) {
+		/* Process the last 1-3 bytes */
+		wr_size = min(wr_fifo_bytes, ctrl->xfer.rem_bytes);
+		ctrl->xfer.rem_bytes -= wr_size;
+
+		byte_buf = xfer_buf;
+		while (wr_size--)
+			writel(*byte_buf++,
+			       ctrl->base + PIO_DATAOUT_1B);
+		ctrl->xfer.tx_buf = byte_buf;
+	} else {
+		/*
+		 * Process all the whole words; to keep things simple we'll
+		 * just wait for the next interrupt to handle the last 1-3
+		 * bytes if we don't have an even number of words.
+		 */
+		rem_words = ctrl->xfer.rem_bytes / QSPI_BYTES_PER_WORD;
+		wr_fifo_words = wr_fifo_bytes / QSPI_BYTES_PER_WORD;
+
+		wr_size = min(rem_words, wr_fifo_words);
+		ctrl->xfer.rem_bytes -= wr_size * QSPI_BYTES_PER_WORD;
+
+		word_buf = xfer_buf;
+		iowrite32_rep(ctrl->base + PIO_DATAOUT_4B, word_buf, wr_size);
+		ctrl->xfer.tx_buf = word_buf + wr_size;
+
+	}
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t qcom_qspi_irq(int irq, void *dev_id)
+{
+	u32 int_status;
+	struct qcom_qspi *ctrl = dev_id;
+	irqreturn_t ret = IRQ_NONE;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ctrl->lock, flags);
+
+	int_status = readl(ctrl->base + MSTR_INT_STATUS);
+	writel(int_status, ctrl->base + MSTR_INT_STATUS);
+
+	if (ctrl->xfer.dir == QSPI_WRITE) {
+		if (int_status & WR_FIFO_EMPTY)
+			ret = pio_write(ctrl);
+	} else {
+		if (int_status & RESP_FIFO_RDY)
+			ret = pio_read(ctrl);
+	}
+
+	if (int_status & QSPI_ERR_IRQS) {
+		if (int_status & RESP_FIFO_UNDERRUN)
+			dev_err(ctrl->dev, "IRQ error: FIFO underrun\n");
+		if (int_status & WR_FIFO_OVERRUN)
+			dev_err(ctrl->dev, "IRQ error: FIFO overrun\n");
+		if (int_status & HRESP_FROM_NOC_ERR)
+			dev_err(ctrl->dev, "IRQ error: NOC response error\n");
+		ret = IRQ_HANDLED;
+	}
+
+	if (!ctrl->xfer.rem_bytes) {
+		writel(0, ctrl->base + MSTR_INT_EN);
+		spi_finalize_current_transfer(dev_get_drvdata(ctrl->dev));
+	}
+
+	spin_unlock_irqrestore(&ctrl->lock, flags);
+	return ret;
+}
+
+static int qcom_qspi_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct device *dev;
+	struct resource *res;
+	struct spi_master *master;
+	struct qcom_qspi *ctrl;
+
+	dev = &pdev->dev;
+
+	master = spi_alloc_master(dev, sizeof(*ctrl));
+	if (!master)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, master);
+
+	ctrl = spi_master_get_devdata(master);
+
+	spin_lock_init(&ctrl->lock);
+	ctrl->dev = dev;
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ctrl->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(ctrl->base)) {
+		ret = PTR_ERR(ctrl->base);
+		goto exit_probe_master_put;
+	}
+
+	ctrl->clks[QSPI_CLK_CORE].id = "core";
+	ctrl->clks[QSPI_CLK_IFACE].id = "iface";
+	ret = devm_clk_bulk_get(dev, QSPI_NUM_CLKS, ctrl->clks);
+	if (ret)
+		goto exit_probe_master_put;
+
+	ret = platform_get_irq(pdev, 0);
+	if (ret < 0) {
+		dev_err(dev, "Failed to get irq %d\n", ret);
+		goto exit_probe_master_put;
+	}
+	ret = devm_request_irq(dev, ret, qcom_qspi_irq,
+			IRQF_TRIGGER_HIGH, dev_name(dev), ctrl);
+	if (ret) {
+		dev_err(dev, "Failed to request irq %d\n", ret);
+		goto exit_probe_master_put;
+	}
+
+	master->max_speed_hz = 300000000;
+	master->num_chipselect = QSPI_NUM_CS;
+	master->bus_num = -1;
+	master->dev.of_node = pdev->dev.of_node;
+	master->mode_bits = SPI_MODE_0 |
+			    SPI_TX_DUAL | SPI_RX_DUAL |
+			    SPI_TX_QUAD | SPI_RX_QUAD;
+	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->prepare_message = qcom_qspi_prepare_message;
+	master->transfer_one = qcom_qspi_transfer_one;
+	master->handle_err = qcom_qspi_handle_err;
+	master->auto_runtime_pm = true;
+
+	pm_runtime_enable(dev);
+
+	ret = spi_register_master(master);
+	if (!ret)
+		return 0;
+
+	pm_runtime_disable(dev);
+
+exit_probe_master_put:
+	spi_master_put(master);
+
+	return ret;
+}
+
+static int qcom_qspi_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = platform_get_drvdata(pdev);
+
+	/* Unregister _before_ disabling pm_runtime() so we stop transfers */
+	spi_unregister_master(master);
+
+	pm_runtime_disable(&pdev->dev);
+
+	return 0;
+}
+
+static int __maybe_unused qcom_qspi_runtime_suspend(struct device *dev)
+{
+	struct spi_master *master = dev_get_drvdata(dev);
+	struct qcom_qspi *ctrl = spi_master_get_devdata(master);
+
+	clk_bulk_disable_unprepare(QSPI_NUM_CLKS, ctrl->clks);
+
+	return 0;
+}
+
+static int __maybe_unused qcom_qspi_runtime_resume(struct device *dev)
+{
+	struct spi_master *master = dev_get_drvdata(dev);
+	struct qcom_qspi *ctrl = spi_master_get_devdata(master);
+
+	return clk_bulk_prepare_enable(QSPI_NUM_CLKS, ctrl->clks);
+}
+
+static int __maybe_unused qcom_qspi_suspend(struct device *dev)
+{
+	struct spi_master *master = dev_get_drvdata(dev);
+	int ret;
+
+	ret = spi_master_suspend(master);
+	if (ret)
+		return ret;
+
+	ret = pm_runtime_force_suspend(dev);
+	if (ret)
+		spi_master_resume(master);
+
+	return ret;
+}
+
+static int __maybe_unused qcom_qspi_resume(struct device *dev)
+{
+	struct spi_master *master = dev_get_drvdata(dev);
+	int ret;
+
+	ret = pm_runtime_force_resume(dev);
+	if (ret)
+		return ret;
+
+	ret = spi_master_resume(master);
+	if (ret)
+		pm_runtime_force_suspend(dev);
+
+	return ret;
+}
+
+static const struct dev_pm_ops qcom_qspi_dev_pm_ops = {
+	SET_RUNTIME_PM_OPS(qcom_qspi_runtime_suspend,
+			   qcom_qspi_runtime_resume, NULL)
+	SET_SYSTEM_SLEEP_PM_OPS(qcom_qspi_suspend, qcom_qspi_resume)
+};
+
+static const struct of_device_id qcom_qspi_dt_match[] = {
+	{ .compatible = "qcom,qspi-v1", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, qcom_qspi_dt_match);
+
+static struct platform_driver qcom_qspi_driver = {
+	.driver = {
+		.name		= "qcom_qspi",
+		.pm		= &qcom_qspi_dev_pm_ops,
+		.of_match_table = qcom_qspi_dt_match,
+	},
+	.probe = qcom_qspi_probe,
+	.remove = qcom_qspi_remove,
+};
+module_platform_driver(qcom_qspi_driver);
+
+MODULE_DESCRIPTION("SPI driver for QSPI cores");
+MODULE_LICENSE("GPL v2");