Merge tag 'staging-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging/IIO fixes from Greg KH:
 "Here are a number of small staging and IIO driver fixes for reported
  issues for 5.5-rc2

  Nothing major, a bunch of tiny IIO driver issues resolved, and some
  staging driver fixes for things that people ran into with 5.5-rc1.
  Full details are in the shortlog.

  All of these have been in linux-next with no reported issues"

* tag 'staging-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
  fbtft: Fix the initialization from property algorithm
  staging: rtl8712: fix interface sanity check
  staging: rtl8188eu: fix interface sanity check
  staging: gigaset: add endpoint-type sanity check
  staging: gigaset: fix illegal free on probe errors
  staging: gigaset: fix general protection fault on probe
  staging: vchiq: call unregister_chrdev_region() when driver registration fails
  staging: exfat: fix multiple definition error of `rename_file'
  staging/wlan-ng: add CRC32 dependency in Kconfig
  staging: hp100: Fix build error without ETHERNET
  staging: fbtft: Do not hardcode SPI CS polarity inversion
  staging: exfat: properly support discard in clr_alloc_bitmap()
  staging/octeon: Mark Ethernet driver as BROKEN
  iio: adc: max9611: Fix too short conversion time delay
  iio: ad7949: fix channels mixups
  iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
  iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
  iio: imu: st_lsm6dsx: fix decimation factor estimation
  iio: imu: inv_mpu6050: fix temperature reporting using bad unit
  iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
  ...

13 files changed, 56 insertions, 25 deletions

diff --git a/drivers/staging/exfat/exfat.h b/drivers/staging/exfat/exfat.h
index 2aac1e000977..51c665a924b7 100644
--- a/drivers/staging/exfat/exfat.h
+++ b/drivers/staging/exfat/exfat.h
@@ -805,8 +805,8 @@ s32 create_dir(struct inode *inode, struct chain_t *p_dir,
 s32 create_file(struct inode *inode, struct chain_t *p_dir,
 		struct uni_name_t *p_uniname, u8 mode, struct file_id_t *fid);
 void remove_file(struct inode *inode, struct chain_t *p_dir, s32 entry);
-s32 rename_file(struct inode *inode, struct chain_t *p_dir, s32 old_entry,
-		struct uni_name_t *p_uniname, struct file_id_t *fid);
+s32 exfat_rename_file(struct inode *inode, struct chain_t *p_dir, s32 old_entry,
+		      struct uni_name_t *p_uniname, struct file_id_t *fid);
 s32 move_file(struct inode *inode, struct chain_t *p_olddir, s32 oldentry,
 	      struct chain_t *p_newdir, struct uni_name_t *p_uniname,
 	      struct file_id_t *fid);
diff --git a/drivers/staging/exfat/exfat_core.c b/drivers/staging/exfat/exfat_core.c
index d2d3447083c7..794000e7bc6f 100644
--- a/drivers/staging/exfat/exfat_core.c
+++ b/drivers/staging/exfat/exfat_core.c
@@ -192,8 +192,6 @@ static s32 clr_alloc_bitmap(struct super_block *sb, u32 clu)
 
 	exfat_bitmap_clear((u8 *)p_fs->vol_amap[i]->b_data, b);
 
-	return sector_write(sb, sector, p_fs->vol_amap[i], 0);
-
 #ifdef CONFIG_EXFAT_DISCARD
 	if (opts->discard) {
 		ret = sb_issue_discard(sb, START_SECTOR(clu),
@@ -202,9 +200,13 @@ static s32 clr_alloc_bitmap(struct super_block *sb, u32 clu)
 		if (ret == -EOPNOTSUPP) {
 			pr_warn("discard not supported by device, disabling");
 			opts->discard = 0;
+		} else {
+			return ret;
 		}
 	}
 #endif /* CONFIG_EXFAT_DISCARD */
+
+	return sector_write(sb, sector, p_fs->vol_amap[i], 0);
 }
 
 static u32 test_alloc_bitmap(struct super_block *sb, u32 clu)
@@ -2322,8 +2324,8 @@ void remove_file(struct inode *inode, struct chain_t *p_dir, s32 entry)
 	fs_func->delete_dir_entry(sb, p_dir, entry, 0, num_entries);
 }
 
-s32 rename_file(struct inode *inode, struct chain_t *p_dir, s32 oldentry,
-		struct uni_name_t *p_uniname, struct file_id_t *fid)
+s32 exfat_rename_file(struct inode *inode, struct chain_t *p_dir, s32 oldentry,
+		      struct uni_name_t *p_uniname, struct file_id_t *fid)
 {
 	s32 ret, newentry = -1, num_old_entries, num_new_entries;
 	sector_t sector_old, sector_new;
diff --git a/drivers/staging/exfat/exfat_super.c b/drivers/staging/exfat/exfat_super.c
index 6e481908c59f..9f91853b189b 100644
--- a/drivers/staging/exfat/exfat_super.c
+++ b/drivers/staging/exfat/exfat_super.c
@@ -1262,8 +1262,8 @@ static int ffsMoveFile(struct inode *old_parent_inode, struct file_id_t *fid,
 	fs_set_vol_flags(sb, VOL_DIRTY);
 
 	if (olddir.dir == newdir.dir)
-		ret = rename_file(new_parent_inode, &olddir, dentry, &uni_name,
-				  fid);
+		ret = exfat_rename_file(new_parent_inode, &olddir, dentry,
+					&uni_name, fid);
 	else
 		ret = move_file(new_parent_inode, &olddir, dentry, &newdir,
 				&uni_name, fid);
diff --git a/drivers/staging/fbtft/fb_uc1611.c b/drivers/staging/fbtft/fb_uc1611.c
index e763205e9e4f..f61e373c75e9 100644
--- a/drivers/staging/fbtft/fb_uc1611.c
+++ b/drivers/staging/fbtft/fb_uc1611.c
@@ -63,11 +63,17 @@ static int init_display(struct fbtft_par *par)
 {
 	int ret;
 
-	/* Set CS active high */
-	par->spi->mode |= SPI_CS_HIGH;
+	/*
+	 * Set CS active inverse polarity: just setting SPI_CS_HIGH does not
+	 * work with GPIO based chip selects that are logically active high
+	 * but inverted inside the GPIO library, so enforce inverted
+	 * semantics.
+	 */
+	par->spi->mode ^= SPI_CS_HIGH;
 	ret = spi_setup(par->spi);
 	if (ret) {
-		dev_err(par->info->device, "Could not set SPI_CS_HIGH\n");
+		dev_err(par->info->device,
+			"Could not set inverse CS polarity\n");
 		return ret;
 	}
 
diff --git a/drivers/staging/fbtft/fb_watterott.c b/drivers/staging/fbtft/fb_watterott.c
index 27cc8eabcbe9..76b25df376b8 100644
--- a/drivers/staging/fbtft/fb_watterott.c
+++ b/drivers/staging/fbtft/fb_watterott.c
@@ -150,10 +150,17 @@ static int init_display(struct fbtft_par *par)
 
 	/* enable SPI interface by having CS and MOSI low during reset */
 	save_mode = par->spi->mode;
-	par->spi->mode |= SPI_CS_HIGH;
-	ret = spi_setup(par->spi); /* set CS inactive low */
+	/*
+	 * Set CS active inverse polarity: just setting SPI_CS_HIGH does not
+	 * work with GPIO based chip selects that are logically active high
+	 * but inverted inside the GPIO library, so enforce inverted
+	 * semantics.
+	 */
+	par->spi->mode ^= SPI_CS_HIGH;
+	ret = spi_setup(par->spi);
 	if (ret) {
-		dev_err(par->info->device, "Could not set SPI_CS_HIGH\n");
+		dev_err(par->info->device,
+			"Could not set inverse CS polarity\n");
 		return ret;
 	}
 	write_reg(par, 0x00); /* make sure mode is set */
diff --git a/drivers/staging/fbtft/fbtft-core.c b/drivers/staging/fbtft/fbtft-core.c
index ffb84987dd86..d3e098b41b1a 100644
--- a/drivers/staging/fbtft/fbtft-core.c
+++ b/drivers/staging/fbtft/fbtft-core.c
@@ -913,7 +913,7 @@ static int fbtft_init_display_from_property(struct fbtft_par *par)
 	if (count == 0)
 		return -EINVAL;
 
-	values = kmalloc_array(count, sizeof(*values), GFP_KERNEL);
+	values = kmalloc_array(count + 1, sizeof(*values), GFP_KERNEL);
 	if (!values)
 		return -ENOMEM;
 
@@ -926,9 +926,9 @@ static int fbtft_init_display_from_property(struct fbtft_par *par)
 		gpiod_set_value(par->gpio.cs, 0);  /* Activate chip */
 
 	index = -1;
-	while (index < count) {
-		val = values[++index];
+	val = values[++index];
 
+	while (index < count) {
 		if (val & FBTFT_OF_INIT_CMD) {
 			val &= 0xFFFF;
 			i = 0;
diff --git a/drivers/staging/hp/Kconfig b/drivers/staging/hp/Kconfig
index fb395cfe6b92..f20ab21a6b2a 100644
--- a/drivers/staging/hp/Kconfig
+++ b/drivers/staging/hp/Kconfig
@@ -6,6 +6,7 @@
 config NET_VENDOR_HP
 	bool "HP devices"
 	default y
+	depends on ETHERNET
 	depends on ISA || EISA || PCI
 	---help---
 	  If you have a network (Ethernet) card belonging to this class, say Y.
diff --git a/drivers/staging/isdn/gigaset/usb-gigaset.c b/drivers/staging/isdn/gigaset/usb-gigaset.c
index 1b9b43659bdf..a20c0bfa68f3 100644
--- a/drivers/staging/isdn/gigaset/usb-gigaset.c
+++ b/drivers/staging/isdn/gigaset/usb-gigaset.c
@@ -571,8 +571,7 @@ static int gigaset_initcshw(struct cardstate *cs)
 {
 	struct usb_cardstate *ucs;
 
-	cs->hw.usb = ucs =
-		kmalloc(sizeof(struct usb_cardstate), GFP_KERNEL);
+	cs->hw.usb = ucs = kzalloc(sizeof(struct usb_cardstate), GFP_KERNEL);
 	if (!ucs) {
 		pr_err("out of memory\n");
 		return -ENOMEM;
@@ -584,9 +583,6 @@ static int gigaset_initcshw(struct cardstate *cs)
 	ucs->bchars[3] = 0;
 	ucs->bchars[4] = 0x11;
 	ucs->bchars[5] = 0x13;
-	ucs->bulk_out_buffer = NULL;
-	ucs->bulk_out_urb = NULL;
-	ucs->read_urb = NULL;
 	tasklet_init(&cs->write_tasklet,
 		     gigaset_modem_fill, (unsigned long) cs);
 
@@ -685,6 +681,11 @@ static int gigaset_probe(struct usb_interface *interface,
 		return -ENODEV;
 	}
 
+	if (hostif->desc.bNumEndpoints < 2) {
+		dev_err(&interface->dev, "missing endpoints\n");
+		return -ENODEV;
+	}
+
 	dev_info(&udev->dev, "%s: Device matched ... !\n", __func__);
 
 	/* allocate memory for our device state and initialize it */
@@ -704,6 +705,12 @@ static int gigaset_probe(struct usb_interface *interface,
 
 	endpoint = &hostif->endpoint[0].desc;
 
+	if (!usb_endpoint_is_bulk_out(endpoint)) {
+		dev_err(&interface->dev, "missing bulk-out endpoint\n");
+		retval = -ENODEV;
+		goto error;
+	}
+
 	buffer_size = le16_to_cpu(endpoint->wMaxPacketSize);
 	ucs->bulk_out_size = buffer_size;
 	ucs->bulk_out_epnum = usb_endpoint_num(endpoint);
@@ -723,6 +730,12 @@ static int gigaset_probe(struct usb_interface *interface,
 
 	endpoint = &hostif->endpoint[1].desc;
 
+	if (!usb_endpoint_is_int_in(endpoint)) {
+		dev_err(&interface->dev, "missing int-in endpoint\n");
+		retval = -ENODEV;
+		goto error;
+	}
+
 	ucs->busy = 0;
 
 	ucs->read_urb = usb_alloc_urb(0, GFP_KERNEL);
diff --git a/drivers/staging/octeon/Kconfig b/drivers/staging/octeon/Kconfig
index 5319909eb2f6..e7f4ddcc1361 100644
--- a/drivers/staging/octeon/Kconfig
+++ b/drivers/staging/octeon/Kconfig
@@ -3,6 +3,7 @@ config OCTEON_ETHERNET
 	tristate "Cavium Networks Octeon Ethernet support"
 	depends on CAVIUM_OCTEON_SOC || COMPILE_TEST
 	depends on NETDEVICES
+	depends on BROKEN
 	select PHYLIB
 	select MDIO_OCTEON
 	help
diff --git a/drivers/staging/rtl8188eu/os_dep/usb_intf.c b/drivers/staging/rtl8188eu/os_dep/usb_intf.c
index 4fac9dca798e..a7cac0719b8b 100644
--- a/drivers/staging/rtl8188eu/os_dep/usb_intf.c
+++ b/drivers/staging/rtl8188eu/os_dep/usb_intf.c
@@ -70,7 +70,7 @@ static struct dvobj_priv *usb_dvobj_init(struct usb_interface *usb_intf)
 	phost_conf = pusbd->actconfig;
 	pconf_desc = &phost_conf->desc;
 
-	phost_iface = &usb_intf->altsetting[0];
+	phost_iface = usb_intf->cur_altsetting;
 	piface_desc = &phost_iface->desc;
 
 	pdvobjpriv->NumInterfaces = pconf_desc->bNumInterfaces;
diff --git a/drivers/staging/rtl8712/usb_intf.c b/drivers/staging/rtl8712/usb_intf.c
index ba1288297ee4..a87562f632a7 100644
--- a/drivers/staging/rtl8712/usb_intf.c
+++ b/drivers/staging/rtl8712/usb_intf.c
@@ -247,7 +247,7 @@ static uint r8712_usb_dvobj_init(struct _adapter *padapter)
 
 	pdvobjpriv->padapter = padapter;
 	padapter->eeprom_address_size = 6;
-	phost_iface = &pintf->altsetting[0];
+	phost_iface = pintf->cur_altsetting;
 	piface_desc = &phost_iface->desc;
 	pdvobjpriv->nr_endpoint = piface_desc->bNumEndpoints;
 	if (pusbd->speed == USB_SPEED_HIGH) {
diff --git a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c
index 02148a24818a..4458c1e60fa3 100644
--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c
+++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c
@@ -3309,7 +3309,7 @@ static int __init vchiq_driver_init(void)
 	return 0;
 
 region_unregister:
-	platform_driver_unregister(&vchiq_driver);
+	unregister_chrdev_region(vchiq_devid, 1);
 
 class_destroy:
 	class_destroy(vchiq_class);
diff --git a/drivers/staging/wlan-ng/Kconfig b/drivers/staging/wlan-ng/Kconfig
index ac136663fa8e..082c16a31616 100644
--- a/drivers/staging/wlan-ng/Kconfig
+++ b/drivers/staging/wlan-ng/Kconfig
@@ -4,6 +4,7 @@ config PRISM2_USB
 	depends on WLAN && USB && CFG80211
 	select WIRELESS_EXT
 	select WEXT_PRIV
+	select CRC32
 	help
 	  This is the wlan-ng prism 2.5/3 USB driver for a wide range of
 	  old USB wireless devices.