Merge tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial driver updates from Greg KH:
 "Here's the big tty/serial driver patchset for 3.18-rc1.

  Lots of little things in here, some good work from Peter Hurley on the
  tty core, and in lots of drivers.  There are also lots of other driver
  updates in here as well, full details in the changelogs.

  All have been in the linux-next tree for a while"

* tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (99 commits)
  Revert "serial/core: Initialize the console pm state"
  tty: serial: 8250: use 32bit variable for rpm_tx_active
  tty: serial: msm: Add earlycon support
  serial/core: Initialize the console pm state
  serial: asc: Conditionally use readl_relaxed (COMPILE_TEST)
  serial: of-serial: add PM suspend/resume support
  m68k: AMIGA_BUILTIN_SERIAL should depend on TTY
  asm/uapi: Add definition of TIOC[SG]RS485
  tty/metag_da: Add console_poll module parameter
  serial: 8250_pci: remove rts_n override from Baytrail quirk
  serial: cadence: Add generic earlycon support
  serial: imx: change the wait even to interruptiable
  serial: imx: terminate the RX DMA when the UART is suspending
  serial: imx: fix throttle/unthrottle callbacks for hardware assisted flow control
  serial: 8250: Add Quark X1000 to 8250_pci.c
  tty: omap-serial: pull out calculation from baud_is_mode16
  tty: omap-serial: fix division by zero
  xen_hvc: no reason to write the type key on xenstore
  tty: serial: 8250_core: remove UART_IER_RDI in serial8250_stop_rx()
  tty: serial: 8250_core: use the ->line argument as a hint in serial8250_find_match_or_unused()
  ...

1 files changed, 249 insertions, 0 deletions

diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
new file mode 100644
index 000000000000..1bb28cb69493
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_fintek.c
@@ -0,0 +1,249 @@
+/*
+ *  Probe for F81216A LPC to 4 UART
+ *
+ *  Based on drivers/tty/serial/8250_pnp.c, by Russell King, et al
+ *
+ *  Copyright (C) 2014 Ricardo Ribalda, Qtechnology A/S
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/pnp.h>
+#include <linux/kernel.h>
+#include <linux/serial_core.h>
+#include  "8250.h"
+
+#define ADDR_PORT 0x4E
+#define DATA_PORT 0x4F
+#define ENTRY_KEY 0x77
+#define EXIT_KEY 0xAA
+#define CHIP_ID1  0x20
+#define CHIP_ID1_VAL 0x02
+#define CHIP_ID2  0x21
+#define CHIP_ID2_VAL 0x16
+#define VENDOR_ID1 0x23
+#define VENDOR_ID1_VAL 0x19
+#define VENDOR_ID2 0x24
+#define VENDOR_ID2_VAL 0x34
+#define LDN 0x7
+
+#define RS485  0xF0
+#define RTS_INVERT BIT(5)
+#define RS485_URA BIT(4)
+#define RXW4C_IRA BIT(3)
+#define TXW4C_IRA BIT(2)
+
+#define DRIVER_NAME "8250_fintek"
+
+static int fintek_8250_enter_key(void){
+
+	if (!request_muxed_region(ADDR_PORT, 2, DRIVER_NAME))
+		return -EBUSY;
+
+	outb(ENTRY_KEY, ADDR_PORT);
+	outb(ENTRY_KEY, ADDR_PORT);
+	return 0;
+}
+
+static void fintek_8250_exit_key(void){
+
+	outb(EXIT_KEY, ADDR_PORT);
+	release_region(ADDR_PORT, 2);
+}
+
+static int fintek_8250_get_index(resource_size_t base_addr)
+{
+	resource_size_t base[] = {0x3f8, 0x2f8, 0x3e8, 0x2e8};
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(base); i++)
+		if (base_addr == base[i])
+			return i;
+
+	return -ENODEV;
+}
+
+static int fintek_8250_check_id(void)
+{
+
+	outb(CHIP_ID1, ADDR_PORT);
+	if (inb(DATA_PORT) != CHIP_ID1_VAL)
+		return -ENODEV;
+
+	outb(CHIP_ID2, ADDR_PORT);
+	if (inb(DATA_PORT) != CHIP_ID2_VAL)
+		return -ENODEV;
+
+	outb(VENDOR_ID1, ADDR_PORT);
+	if (inb(DATA_PORT) != VENDOR_ID1_VAL)
+		return -ENODEV;
+
+	outb(VENDOR_ID2, ADDR_PORT);
+	if (inb(DATA_PORT) != VENDOR_ID2_VAL)
+		return -ENODEV;
+
+	return 0;
+}
+
+static int fintek_8250_rs4850_config(struct uart_8250_port *uart,
+			      struct serial_rs485 *rs485)
+{
+	uint8_t config = 0;
+	int index = fintek_8250_get_index(uart->port.iobase);
+
+	if (index < 0)
+		return -EINVAL;
+
+	if (rs485->flags & SER_RS485_ENABLED)
+		memset(rs485->padding, 0, sizeof(rs485->padding));
+	else
+		memset(rs485, 0, sizeof(*rs485));
+
+	rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+			SER_RS485_RTS_AFTER_SEND;
+
+	if (rs485->delay_rts_before_send) {
+		rs485->delay_rts_before_send = 1;
+		config |= TXW4C_IRA;
+	}
+
+	if (rs485->delay_rts_after_send) {
+		rs485->delay_rts_after_send = 1;
+		config |= RXW4C_IRA;
+	}
+
+	if ((!!(rs485->flags & SER_RS485_RTS_ON_SEND)) ==
+			(!!(rs485->flags & SER_RS485_RTS_AFTER_SEND)))
+		rs485->flags &= SER_RS485_ENABLED;
+	else
+		config |= RS485_URA;
+
+	if (rs485->flags & SER_RS485_RTS_ON_SEND)
+		config |= RTS_INVERT;
+
+	if (fintek_8250_enter_key())
+		return -EBUSY;
+
+	outb(LDN, ADDR_PORT);
+	outb(index, DATA_PORT);
+	outb(RS485, ADDR_PORT);
+	outb(config, DATA_PORT);
+	fintek_8250_exit_key();
+
+	return 0;
+}
+
+static int
+fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
+{
+	int line;
+	struct uart_8250_port uart;
+	int ret;
+
+	if (!pnp_port_valid(dev, 0))
+		return -ENODEV;
+
+	if (fintek_8250_get_index(pnp_port_start(dev, 0)) < 0)
+		return -ENODEV;
+
+	/* Enable configuration registers*/
+	if (fintek_8250_enter_key())
+		return -EBUSY;
+
+	/*Check ID*/
+	ret = fintek_8250_check_id();
+	fintek_8250_exit_key();
+	if (ret)
+		return ret;
+
+	memset(&uart, 0, sizeof(uart));
+	if (!pnp_irq_valid(dev, 0))
+		return -ENODEV;
+	uart.port.irq = pnp_irq(dev, 0);
+	uart.port.iobase = pnp_port_start(dev, 0);
+	uart.port.iotype = UPIO_PORT;
+	uart.rs485_config = fintek_8250_rs4850_config;
+
+	uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
+	if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE)
+		uart.port.flags |= UPF_SHARE_IRQ;
+	uart.port.uartclk = 1843200;
+	uart.port.dev = &dev->dev;
+
+	line = serial8250_register_8250_port(&uart);
+	if (line < 0)
+		return -ENODEV;
+
+	pnp_set_drvdata(dev, (void *)((long)line + 1));
+	return 0;
+}
+
+static void fintek_8250_remove(struct pnp_dev *dev)
+{
+	long line = (long)pnp_get_drvdata(dev);
+
+	if (line)
+		serial8250_unregister_port(line - 1);
+}
+
+#ifdef CONFIG_PM
+static int fintek_8250_suspend(struct pnp_dev *dev, pm_message_t state)
+{
+	long line = (long)pnp_get_drvdata(dev);
+
+	if (!line)
+		return -ENODEV;
+	serial8250_suspend_port(line - 1);
+	return 0;
+}
+
+static int fintek_8250_resume(struct pnp_dev *dev)
+{
+	long line = (long)pnp_get_drvdata(dev);
+
+	if (!line)
+		return -ENODEV;
+	serial8250_resume_port(line - 1);
+	return 0;
+}
+#else
+#define fintek_8250_suspend NULL
+#define fintek_8250_resume NULL
+#endif /* CONFIG_PM */
+
+static const struct pnp_device_id fintek_dev_table[] = {
+	/* Qtechnology Panel PC / IO1000 */
+	{ "PNP0501"},
+	{}
+};
+
+MODULE_DEVICE_TABLE(pnp, fintek_dev_table);
+
+static struct pnp_driver fintek_8250_driver = {
+	.name		= DRIVER_NAME,
+	.probe		= fintek_8250_probe,
+	.remove		= fintek_8250_remove,
+	.suspend	= fintek_8250_suspend,
+	.resume		= fintek_8250_resume,
+	.id_table	= fintek_dev_table,
+};
+
+static int fintek_8250_init(void)
+{
+	return pnp_register_driver(&fintek_8250_driver);
+}
+module_init(fintek_8250_init);
+
+static void fintek_8250_exit(void)
+{
+	pnp_unregister_driver(&fintek_8250_driver);
+}
+module_exit(fintek_8250_exit);
+
+MODULE_DESCRIPTION("Fintek F812164 module");
+MODULE_AUTHOR("Ricardo Ribalda <ricardo.ribalda@gmail.com>");
+MODULE_LICENSE("GPL");