usb: dwc3: gadget: Add support for disabling U1 and U2 entries

Gadget applications may have a requirement to disable the U1 and U2
entry based on the usecase. Below are few usecases where the disabling
U1/U2 entries may be possible.

Usecase 1:
When combining dwc3 with an redriver for a USB Type-C device solution, it
sometimes have problems with leaving U1/U2 for certain hosts, resulting in
link training errors and reconnects. For this U1/U2 state entries may be
avoided.

Usecase 2:
When performing performance benchmarking on mass storage gadget the
U1 and U2 entries can be disabled.

Usecase 3:
When periodic transfers like ISOC transfers are used with bInterval
of 1 which doesn't require the link to enter into U1 or U2 state entry
(since ping is issued from host for every uframe interval). In this
case the U1 and U2 entry can be disabled.

Disablement of U1/U2 can be done by setting U1DevExitLat and U2DevExitLat
values to 0 in the BOS descriptor. Host on seeing 0 value for U1DevExitLat
and U2DevExitLat, it doesn't send SET_SEL requests to the gadget. There
may be some hosts which may send SET_SEL requests even after seeing 0 in
the UxDevExitLat of BOS descriptor. To aviod U1/U2 entries for these type
of hosts, dwc3 controller can be programmed to reject those U1/U2 requests
by not enabling ACCEPTUxENA bits in DCTL register.

This patch updates the same.

Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

1 files changed, 20 insertions, 0 deletions

diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index d67655384eb2..2751d3e98f5f 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -2073,6 +2073,25 @@ out:
 	return 0;
 }
 
+static void dwc3_gadget_config_params(struct usb_gadget *g,
+				      struct usb_dcd_config_params *params)
+{
+	struct dwc3		*dwc = gadget_to_dwc(g);
+
+	/* U1 Device exit Latency */
+	if (dwc->dis_u1_entry_quirk)
+		params->bU1devExitLat = 0;
+	else
+		params->bU1devExitLat = DWC3_DEFAULT_U1_DEV_EXIT_LAT;
+
+	/* U2 Device exit Latency */
+	if (dwc->dis_u2_entry_quirk)
+		params->bU2DevExitLat = 0;
+	else
+		params->bU2DevExitLat =
+				cpu_to_le16(DWC3_DEFAULT_U2_DEV_EXIT_LAT);
+}
+
 static void dwc3_gadget_set_speed(struct usb_gadget *g,
 				  enum usb_device_speed speed)
 {
@@ -2142,6 +2161,7 @@ static const struct usb_gadget_ops dwc3_gadget_ops = {
 	.udc_start		= dwc3_gadget_start,
 	.udc_stop		= dwc3_gadget_stop,
 	.udc_set_speed		= dwc3_gadget_set_speed,
+	.get_config_params	= dwc3_gadget_config_params,
 };
 
 /* -------------------------------------------------------------------------- */