Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] Fix PCI_DMA_BUS_IS_PHYS for ARM
  [ARM] 5247/1: tosa: SW_EAR_IN support
  [ARM] 5246/1: tosa: add proper clock alias for tc6393xb clock
  [ARM] 5245/1: Fix warning about unused return value in drivers/pcmcia
  [ARM] OMAP: Fix MMC device data
  imx serial: fix rts handling for non imx1 based hardware
  imx serial: set RXD mux bit on i.MX27 and i.MX31
  i.MX serial: fix init failure
  pcm037: add rts/cts support for serial port

2 files changed, 27 insertions, 6 deletions

diff --git a/drivers/pcmcia/soc_common.c b/drivers/pcmcia/soc_common.c
index c48f3f69bdaf..da3972153226 100644
--- a/drivers/pcmcia/soc_common.c
+++ b/drivers/pcmcia/soc_common.c
@@ -748,7 +748,9 @@ int soc_common_drv_pcmcia_probe(struct device *dev, struct pcmcia_low_level *ops
 
 		add_timer(&skt->poll_timer);
 
-		device_create_file(&skt->socket.dev, &dev_attr_status);
+		ret = device_create_file(&skt->socket.dev, &dev_attr_status);
+		if (ret)
+			goto out_err_8;
 	}
 
 	dev_set_drvdata(dev, sinfo);
@@ -758,6 +760,8 @@ int soc_common_drv_pcmcia_probe(struct device *dev, struct pcmcia_low_level *ops
 	do {
 		skt = &sinfo->skt[i];
 
+		device_remove_file(&skt->socket.dev, &dev_attr_status);
+ out_err_8:
 		del_timer_sync(&skt->poll_timer);
 		pcmcia_unregister_socket(&skt->socket);
 
diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c
index 6a29f9330a73..3f90f1bbbbcd 100644
--- a/drivers/serial/imx.c
+++ b/drivers/serial/imx.c
@@ -127,8 +127,13 @@
 #define  UCR3_RXDSEN	 (1<<6)  /* Receive status interrupt enable */
 #define  UCR3_AIRINTEN   (1<<5)  /* Async IR wake interrupt enable */
 #define  UCR3_AWAKEN	 (1<<4)  /* Async wake interrupt enable */
-#define  UCR3_REF25 	 (1<<3)  /* Ref freq 25 MHz */
-#define  UCR3_REF30 	 (1<<2)  /* Ref Freq 30 MHz */
+#ifdef CONFIG_ARCH_IMX
+#define  UCR3_REF25 	 (1<<3)  /* Ref freq 25 MHz, only on mx1 */
+#define  UCR3_REF30 	 (1<<2)  /* Ref Freq 30 MHz, only on mx1 */
+#endif
+#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
+#define  UCR3_RXDMUXSEL	 (1<<2)  /* RXD Muxed Input Select, on mx2/mx3 */
+#endif
 #define  UCR3_INVT  	 (1<<1)  /* Inverted Infrared transmission */
 #define  UCR3_BPEN  	 (1<<0)  /* Preset registers enable */
 #define  UCR4_CTSTL_32   (32<<10) /* CTS trigger level (32 chars) */
@@ -445,7 +450,7 @@ static irqreturn_t imx_int(int irq, void *dev_id)
 			readl(sport->port.membase + UCR1) & UCR1_TXMPTYEN)
 		imx_txint(irq, dev_id);
 
-	if (sts & USR1_RTSS)
+	if (sts & USR1_RTSD)
 		imx_rtsint(irq, dev_id);
 
 	return IRQ_HANDLED;
@@ -598,6 +603,12 @@ static int imx_startup(struct uart_port *port)
 	temp |= (UCR2_RXEN | UCR2_TXEN);
 	writel(temp, sport->port.membase + UCR2);
 
+#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
+	temp = readl(sport->port.membase + UCR3);
+	temp |= UCR3_RXDMUXSEL;
+	writel(temp, sport->port.membase + UCR3);
+#endif
+
 	/*
 	 * Enable modem status interrupts
 	 */
@@ -1133,13 +1144,19 @@ static int serial_imx_probe(struct platform_device *pdev)
 	if(pdata && (pdata->flags & IMXUART_HAVE_RTSCTS))
 		sport->have_rtscts = 1;
 
-	if (pdata->init)
-		pdata->init(pdev);
+	if (pdata->init) {
+		ret = pdata->init(pdev);
+		if (ret)
+			goto clkput;
+	}
 
 	uart_add_one_port(&imx_reg, &sport->port);
 	platform_set_drvdata(pdev, &sport->port);
 
 	return 0;
+clkput:
+	clk_put(sport->clk);
+	clk_disable(sport->clk);
 unmap:
 	iounmap(sport->port.membase);
 free: