powerpc: Move include files to arch/powerpc/include/asm

from include/asm-powerpc.  This is the result of a

mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm

Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly.  Of the latter only
one was outside the arch code and it is a driver only built for powerpc.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

1 files changed, 0 insertions, 296 deletions

diff --git a/include/asm-powerpc/hvcall.h b/include/asm-powerpc/hvcall.h
deleted file mode 100644
index fbe2932fa9e9..000000000000
--- a/include/asm-powerpc/hvcall.h
+++ /dev/null
@@ -1,296 +0,0 @@
-#ifndef _ASM_POWERPC_HVCALL_H
-#define _ASM_POWERPC_HVCALL_H
-#ifdef __KERNEL__
-
-#define HVSC			.long 0x44000022
-
-#define H_SUCCESS	0
-#define H_BUSY		1	/* Hardware busy -- retry later */
-#define H_CLOSED	2	/* Resource closed */
-#define H_NOT_AVAILABLE 3
-#define H_CONSTRAINED	4	/* Resource request constrained to max allowed */
-#define H_PARTIAL       5
-#define H_IN_PROGRESS	14	/* Kind of like busy */
-#define H_PAGE_REGISTERED 15
-#define H_PARTIAL_STORE   16
-#define H_PENDING	17	/* returned from H_POLL_PENDING */
-#define H_CONTINUE	18	/* Returned from H_Join on success */
-#define H_LONG_BUSY_START_RANGE		9900  /* Start of long busy range */
-#define H_LONG_BUSY_ORDER_1_MSEC	9900  /* Long busy, hint that 1msec \
-						 is a good time to retry */
-#define H_LONG_BUSY_ORDER_10_MSEC	9901  /* Long busy, hint that 10msec \
-						 is a good time to retry */
-#define H_LONG_BUSY_ORDER_100_MSEC 	9902  /* Long busy, hint that 100msec \
-						 is a good time to retry */
-#define H_LONG_BUSY_ORDER_1_SEC		9903  /* Long busy, hint that 1sec \
-						 is a good time to retry */
-#define H_LONG_BUSY_ORDER_10_SEC	9904  /* Long busy, hint that 10sec \
-						 is a good time to retry */
-#define H_LONG_BUSY_ORDER_100_SEC	9905  /* Long busy, hint that 100sec \
-						 is a good time to retry */
-#define H_LONG_BUSY_END_RANGE		9905  /* End of long busy range */
-#define H_HARDWARE	-1	/* Hardware error */
-#define H_FUNCTION	-2	/* Function not supported */
-#define H_PRIVILEGE	-3	/* Caller not privileged */
-#define H_PARAMETER	-4	/* Parameter invalid, out-of-range or conflicting */
-#define H_BAD_MODE	-5	/* Illegal msr value */
-#define H_PTEG_FULL	-6	/* PTEG is full */
-#define H_NOT_FOUND	-7	/* PTE was not found" */
-#define H_RESERVED_DABR	-8	/* DABR address is reserved by the hypervisor on this processor" */
-#define H_NO_MEM	-9
-#define H_AUTHORITY	-10
-#define H_PERMISSION	-11
-#define H_DROPPED	-12
-#define H_SOURCE_PARM	-13
-#define H_DEST_PARM	-14
-#define H_REMOTE_PARM	-15
-#define H_RESOURCE	-16
-#define H_ADAPTER_PARM  -17
-#define H_RH_PARM       -18
-#define H_RCQ_PARM      -19
-#define H_SCQ_PARM      -20
-#define H_EQ_PARM       -21
-#define H_RT_PARM       -22
-#define H_ST_PARM       -23
-#define H_SIGT_PARM     -24
-#define H_TOKEN_PARM    -25
-#define H_MLENGTH_PARM  -27
-#define H_MEM_PARM      -28
-#define H_MEM_ACCESS_PARM -29
-#define H_ATTR_PARM     -30
-#define H_PORT_PARM     -31
-#define H_MCG_PARM      -32
-#define H_VL_PARM       -33
-#define H_TSIZE_PARM    -34
-#define H_TRACE_PARM    -35
-
-#define H_MASK_PARM     -37
-#define H_MCG_FULL      -38
-#define H_ALIAS_EXIST   -39
-#define H_P_COUNTER     -40
-#define H_TABLE_FULL    -41
-#define H_ALT_TABLE     -42
-#define H_MR_CONDITION  -43
-#define H_NOT_ENOUGH_RESOURCES -44
-#define H_R_STATE       -45
-#define H_RESCINDEND    -46
-
-
-/* Long Busy is a condition that can be returned by the firmware
- * when a call cannot be completed now, but the identical call
- * should be retried later.  This prevents calls blocking in the
- * firmware for long periods of time.  Annoyingly the firmware can return
- * a range of return codes, hinting at how long we should wait before
- * retrying.  If you don't care for the hint, the macro below is a good
- * way to check for the long_busy return codes
- */
-#define H_IS_LONG_BUSY(x)  ((x >= H_LONG_BUSY_START_RANGE) \
-			     && (x <= H_LONG_BUSY_END_RANGE))
-
-/* Flags */
-#define H_LARGE_PAGE		(1UL<<(63-16))
-#define H_EXACT			(1UL<<(63-24))	/* Use exact PTE or return H_PTEG_FULL */
-#define H_R_XLATE		(1UL<<(63-25))	/* include a valid logical page num in the pte if the valid bit is set */
-#define H_READ_4		(1UL<<(63-26))	/* Return 4 PTEs */
-#define H_PAGE_STATE_CHANGE	(1UL<<(63-28))
-#define H_PAGE_UNUSED		((1UL<<(63-29)) | (1UL<<(63-30)))
-#define H_PAGE_SET_UNUSED	(H_PAGE_STATE_CHANGE | H_PAGE_UNUSED)
-#define H_PAGE_SET_LOANED	(H_PAGE_SET_UNUSED | (1UL<<(63-31)))
-#define H_PAGE_SET_ACTIVE	H_PAGE_STATE_CHANGE
-#define H_AVPN			(1UL<<(63-32))	/* An avpn is provided as a sanity test */
-#define H_ANDCOND		(1UL<<(63-33))
-#define H_ICACHE_INVALIDATE	(1UL<<(63-40))	/* icbi, etc.  (ignored for IO pages) */
-#define H_ICACHE_SYNCHRONIZE	(1UL<<(63-41))	/* dcbst, icbi, etc (ignored for IO pages */
-#define H_ZERO_PAGE		(1UL<<(63-48))	/* zero the page before mapping (ignored for IO pages) */
-#define H_COPY_PAGE		(1UL<<(63-49))
-#define H_N			(1UL<<(63-61))
-#define H_PP1			(1UL<<(63-62))
-#define H_PP2			(1UL<<(63-63))
-
-/* VASI States */
-#define H_VASI_INVALID          0
-#define H_VASI_ENABLED          1
-#define H_VASI_ABORTED          2
-#define H_VASI_SUSPENDING       3
-#define H_VASI_SUSPENDED        4
-#define H_VASI_RESUMED          5
-#define H_VASI_COMPLETED        6
-
-/* DABRX flags */
-#define H_DABRX_HYPERVISOR	(1UL<<(63-61))
-#define H_DABRX_KERNEL		(1UL<<(63-62))
-#define H_DABRX_USER		(1UL<<(63-63))
-
-/* Each control block has to be on a 4K bondary */
-#define H_CB_ALIGNMENT          4096
-
-/* pSeries hypervisor opcodes */
-#define H_REMOVE		0x04
-#define H_ENTER			0x08
-#define H_READ			0x0c
-#define H_CLEAR_MOD		0x10
-#define H_CLEAR_REF		0x14
-#define H_PROTECT		0x18
-#define H_GET_TCE		0x1c
-#define H_PUT_TCE		0x20
-#define H_SET_SPRG0		0x24
-#define H_SET_DABR		0x28
-#define H_PAGE_INIT		0x2c
-#define H_SET_ASR		0x30
-#define H_ASR_ON		0x34
-#define H_ASR_OFF		0x38
-#define H_LOGICAL_CI_LOAD	0x3c
-#define H_LOGICAL_CI_STORE	0x40
-#define H_LOGICAL_CACHE_LOAD	0x44
-#define H_LOGICAL_CACHE_STORE	0x48
-#define H_LOGICAL_ICBI		0x4c
-#define H_LOGICAL_DCBF		0x50
-#define H_GET_TERM_CHAR		0x54
-#define H_PUT_TERM_CHAR		0x58
-#define H_REAL_TO_LOGICAL	0x5c
-#define H_HYPERVISOR_DATA	0x60
-#define H_EOI			0x64
-#define H_CPPR			0x68
-#define H_IPI			0x6c
-#define H_IPOLL			0x70
-#define H_XIRR			0x74
-#define H_PERFMON		0x7c
-#define H_MIGRATE_DMA		0x78
-#define H_REGISTER_VPA		0xDC
-#define H_CEDE			0xE0
-#define H_CONFER		0xE4
-#define H_PROD			0xE8
-#define H_GET_PPP		0xEC
-#define H_SET_PPP		0xF0
-#define H_PURR			0xF4
-#define H_PIC			0xF8
-#define H_REG_CRQ		0xFC
-#define H_FREE_CRQ		0x100
-#define H_VIO_SIGNAL		0x104
-#define H_SEND_CRQ		0x108
-#define H_COPY_RDMA		0x110
-#define H_REGISTER_LOGICAL_LAN	0x114
-#define H_FREE_LOGICAL_LAN	0x118
-#define H_ADD_LOGICAL_LAN_BUFFER 0x11C
-#define H_SEND_LOGICAL_LAN	0x120
-#define H_BULK_REMOVE		0x124
-#define H_MULTICAST_CTRL	0x130
-#define H_SET_XDABR		0x134
-#define H_STUFF_TCE		0x138
-#define H_PUT_TCE_INDIRECT	0x13C
-#define H_CHANGE_LOGICAL_LAN_MAC 0x14C
-#define H_VTERM_PARTNER_INFO	0x150
-#define H_REGISTER_VTERM	0x154
-#define H_FREE_VTERM		0x158
-#define H_RESET_EVENTS          0x15C
-#define H_ALLOC_RESOURCE        0x160
-#define H_FREE_RESOURCE         0x164
-#define H_MODIFY_QP             0x168
-#define H_QUERY_QP              0x16C
-#define H_REREGISTER_PMR        0x170
-#define H_REGISTER_SMR          0x174
-#define H_QUERY_MR              0x178
-#define H_QUERY_MW              0x17C
-#define H_QUERY_HCA             0x180
-#define H_QUERY_PORT            0x184
-#define H_MODIFY_PORT           0x188
-#define H_DEFINE_AQP1           0x18C
-#define H_GET_TRACE_BUFFER      0x190
-#define H_DEFINE_AQP0           0x194
-#define H_RESIZE_MR             0x198
-#define H_ATTACH_MCQP           0x19C
-#define H_DETACH_MCQP           0x1A0
-#define H_CREATE_RPT            0x1A4
-#define H_REMOVE_RPT            0x1A8
-#define H_REGISTER_RPAGES       0x1AC
-#define H_DISABLE_AND_GETC      0x1B0
-#define H_ERROR_DATA            0x1B4
-#define H_GET_HCA_INFO          0x1B8
-#define H_GET_PERF_COUNT        0x1BC
-#define H_MANAGE_TRACE          0x1C0
-#define H_FREE_LOGICAL_LAN_BUFFER 0x1D4
-#define H_QUERY_INT_STATE       0x1E4
-#define H_POLL_PENDING		0x1D8
-#define H_ILLAN_ATTRIBUTES	0x244
-#define H_JOIN			0x298
-#define H_VASI_STATE            0x2A4
-#define H_ENABLE_CRQ		0x2B0
-#define H_SET_MPP		0x2D0
-#define H_GET_MPP		0x2D4
-#define MAX_HCALL_OPCODE	H_GET_MPP
-
-#ifndef __ASSEMBLY__
-
-/**
- * plpar_hcall_norets: - Make a pseries hypervisor call with no return arguments
- * @opcode: The hypervisor call to make.
- *
- * This call supports up to 7 arguments and only returns the status of
- * the hcall. Use this version where possible, its slightly faster than
- * the other plpar_hcalls.
- */
-long plpar_hcall_norets(unsigned long opcode, ...);
-
-/**
- * plpar_hcall: - Make a pseries hypervisor call
- * @opcode: The hypervisor call to make.
- * @retbuf: Buffer to store up to 4 return arguments in.
- *
- * This call supports up to 6 arguments and 4 return arguments. Use
- * PLPAR_HCALL_BUFSIZE to size the return argument buffer.
- *
- * Used for all but the craziest of phyp interfaces (see plpar_hcall9)
- */
-#define PLPAR_HCALL_BUFSIZE 4
-long plpar_hcall(unsigned long opcode, unsigned long *retbuf, ...);
-
-/**
- * plpar_hcall_raw: - Make a hypervisor call without calculating hcall stats
- * @opcode: The hypervisor call to make.
- * @retbuf: Buffer to store up to 4 return arguments in.
- *
- * This call supports up to 6 arguments and 4 return arguments. Use
- * PLPAR_HCALL_BUFSIZE to size the return argument buffer.
- *
- * Used when phyp interface needs to be called in real mode. Similar to
- * plpar_hcall, but plpar_hcall_raw works in real mode and does not
- * calculate hypervisor call statistics.
- */
-long plpar_hcall_raw(unsigned long opcode, unsigned long *retbuf, ...);
-
-/**
- * plpar_hcall9: - Make a pseries hypervisor call with up to 9 return arguments
- * @opcode: The hypervisor call to make.
- * @retbuf: Buffer to store up to 9 return arguments in.
- *
- * This call supports up to 9 arguments and 9 return arguments. Use
- * PLPAR_HCALL9_BUFSIZE to size the return argument buffer.
- */
-#define PLPAR_HCALL9_BUFSIZE 9
-long plpar_hcall9(unsigned long opcode, unsigned long *retbuf, ...);
-
-/* For hcall instrumentation.  One structure per-hcall, per-CPU */
-struct hcall_stats {
-	unsigned long	num_calls;	/* number of calls (on this CPU) */
-	unsigned long	tb_total;	/* total wall time (mftb) of calls. */
-	unsigned long	purr_total;	/* total cpu time (PURR) of calls. */
-};
-#define HCALL_STAT_ARRAY_SIZE	((MAX_HCALL_OPCODE >> 2) + 1)
-
-struct hvcall_mpp_data {
-	unsigned long entitled_mem;
-	unsigned long mapped_mem;
-	unsigned short group_num;
-	unsigned short pool_num;
-	unsigned char mem_weight;
-	unsigned char unallocated_mem_weight;
-	unsigned long unallocated_entitlement;  /* value in bytes */
-	unsigned long pool_size;
-	signed long loan_request;
-	unsigned long backing_mem;
-};
-
-int h_get_mpp(struct hvcall_mpp_data *);
-#endif /* __ASSEMBLY__ */
-#endif /* __KERNEL__ */
-#endif /* _ASM_POWERPC_HVCALL_H */