diff options
| -rw-r--r-- | Documentation/devicetree/bindings/usb/omap-usb.txt | 30 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/usb-phy.txt | 5 | ||||
| -rw-r--r-- | drivers/usb/phy/Kconfig | 10 | ||||
| -rw-r--r-- | drivers/usb/phy/Makefile | 1 | ||||
| -rw-r--r-- | drivers/usb/phy/omap-control-usb.c | 295 | ||||
| -rw-r--r-- | include/linux/usb/omap_control_usb.h | 92 |
6 files changed, 432 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 29a043ecda52..3d78cc2b486e 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -1,4 +1,4 @@ -OMAP GLUE +OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS OMAP MUSB GLUE - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" @@ -16,6 +16,10 @@ OMAP MUSB GLUE - power : Should be "50". This signifies the controller can supply upto 100mA when operating in host mode. +Optional properties: + - ctrl-module : phandle of the control module this glue uses to write to + mailbox + SOC specific device node entry usb_otg_hs: usb_otg_hs@4a0ab000 { compatible = "ti,omap4-musb"; @@ -23,6 +27,7 @@ usb_otg_hs: usb_otg_hs@4a0ab000 { multipoint = <1>; num_eps = <16>; ram_bits = <12>; + ctrl-module = <&omap_control_usb>; }; Board specific device node entry @@ -31,3 +36,26 @@ Board specific device node entry mode = <3>; power = <50>; }; + +OMAP CONTROL USB + +Required properties: + - compatible: Should be "ti,omap-control-usb" + - reg : Address and length of the register set for the device. It contains + the address of "control_dev_conf" and "otghs_control" or "phy_power_usb" + depending upon omap4 or omap5. + - reg-names: The names of the register addresses corresponding to the registers + filled in "reg". + - ti,type: This is used to differentiate whether the control module has + usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to + notify events to the musb core and omap5 has usb3 phy power register to + power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3 + phy power. + +omap_control_usb: omap-control-usb@4a002300 { + compatible = "ti,omap-control-usb"; + reg = <0x4a002300 0x4>, + <0x4a00233c 0x4>; + reg-names = "control_dev_conf", "otghs_control"; + ti,type = <1>; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt index 80d4148cb661..4234105302db 100644 --- a/Documentation/devicetree/bindings/usb/usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt @@ -8,10 +8,15 @@ Required properties: add the address of control module dev conf register until a driver for control module is added +Optional properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + This is usually a subnode of ocp2scp to which it is connected. usb2phy@4a0ad080 { compatible = "ti,omap-usb2"; reg = <0x4a0ad080 0x58>, <0x4a002300 0x4>; + ctrl-module = <&omap_control_usb>; }; diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig index fae4d08c0ddd..053696a2b6ef 100644 --- a/drivers/usb/phy/Kconfig +++ b/drivers/usb/phy/Kconfig @@ -14,6 +14,16 @@ config OMAP_USB2 The USB OTG controller communicates with the comparator using this driver. +config OMAP_CONTROL_USB + tristate "OMAP CONTROL USB Driver" + depends on ARCH_OMAP2PLUS + help + Enable this to add support for the USB part present in the control + module. This driver has API to power on the USB2 PHY and to write to + the mailbox. The mailbox is present only in omap4 and the register to + power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an + additional register to power on USB3 PHY. + config USB_ISP1301 tristate "NXP ISP1301 USB transceiver support" depends on USB || USB_GADGET diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile index ec304f642402..ee977671f530 100644 --- a/drivers/usb/phy/Makefile +++ b/drivers/usb/phy/Makefile @@ -5,6 +5,7 @@ ccflags-$(CONFIG_USB_DEBUG) := -DDEBUG obj-$(CONFIG_OMAP_USB2) += omap-usb2.o +obj-$(CONFIG_OMAP_CONTROL_USB) += omap-control-usb.o obj-$(CONFIG_USB_ISP1301) += isp1301.o obj-$(CONFIG_MV_U3D_PHY) += mv_u3d_phy.o obj-$(CONFIG_USB_EHCI_TEGRA) += tegra_usb_phy.o diff --git a/drivers/usb/phy/omap-control-usb.c b/drivers/usb/phy/omap-control-usb.c new file mode 100644 index 000000000000..5323b71c3521 --- /dev/null +++ b/drivers/usb/phy/omap-control-usb.c @@ -0,0 +1,295 @@ +/* + * omap-control-usb.c - The USB part of control module. + * + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Author: Kishon Vijay Abraham I <kishon@ti.com> + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/of.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/clk.h> +#include <linux/usb/omap_control_usb.h> + +static struct omap_control_usb *control_usb; + +/** + * omap_get_control_dev - returns the device pointer for this control device + * + * This API should be called to get the device pointer for this control + * module device. This device pointer should be used for called other + * exported API's in this driver. + * + * To be used by PHY driver and glue driver. + */ +struct device *omap_get_control_dev(void) +{ + if (!control_usb) + return ERR_PTR(-ENODEV); + + return control_usb->dev; +} +EXPORT_SYMBOL_GPL(omap_get_control_dev); + +/** + * omap_control_usb3_phy_power - power on/off the serializer using control + * module + * @dev: the control module device + * @on: 0 to off and 1 to on based on powering on or off the PHY + * + * usb3 PHY driver should call this API to power on or off the PHY. + */ +void omap_control_usb3_phy_power(struct device *dev, bool on) +{ + u32 val; + unsigned long rate; + struct omap_control_usb *control_usb = dev_get_drvdata(dev); + + if (control_usb->type != OMAP_CTRL_DEV_TYPE2) + return; + + rate = clk_get_rate(control_usb->sys_clk); + rate = rate/1000000; + + val = readl(control_usb->phy_power); + + if (on) { + val &= ~(OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK | + OMAP_CTRL_USB_PWRCTL_CLK_FREQ_MASK); + val |= OMAP_CTRL_USB3_PHY_TX_RX_POWERON << + OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT; + val |= rate << OMAP_CTRL_USB_PWRCTL_CLK_FREQ_SHIFT; + } else { + val &= ~OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK; + val |= OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF << + OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT; + } + + writel(val, control_usb->phy_power); +} +EXPORT_SYMBOL_GPL(omap_control_usb3_phy_power); + +/** + * omap_control_usb_phy_power - power on/off the phy using control module reg + * @dev: the control module device + * @on: 0 or 1, based on powering on or off the PHY + */ +void omap_control_usb_phy_power(struct device *dev, int on) +{ + u32 val; + struct omap_control_usb *control_usb = dev_get_drvdata(dev); + + val = readl(control_usb->dev_conf); + + if (on) + val &= ~OMAP_CTRL_DEV_PHY_PD; + else + val |= OMAP_CTRL_DEV_PHY_PD; + + writel(val, control_usb->dev_conf); +} +EXPORT_SYMBOL_GPL(omap_control_usb_phy_power); + +/** + * omap_control_usb_host_mode - set AVALID, VBUSVALID and ID pin in grounded + * @ctrl_usb: struct omap_control_usb * + * + * Writes to the mailbox register to notify the usb core that a usb + * device has been connected. + */ +static void omap_control_usb_host_mode(struct omap_control_usb *ctrl_usb) +{ + u32 val; + + val = readl(ctrl_usb->otghs_control); + val &= ~(OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_SESSEND); + val |= OMAP_CTRL_DEV_AVALID | OMAP_CTRL_DEV_VBUSVALID; + writel(val, ctrl_usb->otghs_control); +} + +/** + * omap_control_usb_device_mode - set AVALID, VBUSVALID and ID pin in high + * impedance + * @ctrl_usb: struct omap_control_usb * + * + * Writes to the mailbox register to notify the usb core that it has been + * connected to a usb host. + */ +static void omap_control_usb_device_mode(struct omap_control_usb *ctrl_usb) +{ + u32 val; + + val = readl(ctrl_usb->otghs_control); + val &= ~OMAP_CTRL_DEV_SESSEND; + val |= OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_AVALID | + OMAP_CTRL_DEV_VBUSVALID; + writel(val, ctrl_usb->otghs_control); +} + +/** + * omap_control_usb_set_sessionend - Enable SESSIONEND and IDIG to high + * impedance + * @ctrl_usb: struct omap_control_usb * + * + * Writes to the mailbox register to notify the usb core it's now in + * disconnected state. + */ +static void omap_control_usb_set_sessionend(struct omap_control_usb *ctrl_usb) +{ + u32 val; + + val = readl(ctrl_usb->otghs_control); + val &= ~(OMAP_CTRL_DEV_AVALID | OMAP_CTRL_DEV_VBUSVALID); + val |= OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_SESSEND; + writel(val, ctrl_usb->otghs_control); +} + +/** + * omap_control_usb_set_mode - Calls to functions to set USB in one of host mode + * or device mode or to denote disconnected state + * @dev: the control module device + * @mode: The mode to which usb should be configured + * + * This is an API to write to the mailbox register to notify the usb core that + * a usb device has been connected. + */ +void omap_control_usb_set_mode(struct device *dev, + enum omap_control_usb_mode mode) +{ + struct omap_control_usb *ctrl_usb; + + if (IS_ERR(dev) || control_usb->type != OMAP_CTRL_DEV_TYPE1) + return; + + ctrl_usb = dev_get_drvdata(dev); + + switch (mode) { + case USB_MODE_HOST: + omap_control_usb_host_mode(ctrl_usb); + break; + case USB_MODE_DEVICE: + omap_control_usb_device_mode(ctrl_usb); + break; + case USB_MODE_DISCONNECT: + omap_control_usb_set_sessionend(ctrl_usb); + break; + default: + dev_vdbg(dev, "invalid omap control usb mode\n"); + } +} +EXPORT_SYMBOL_GPL(omap_control_usb_set_mode); + +static int omap_control_usb_probe(struct platform_device *pdev) +{ + struct resource *res; + struct device_node *np = pdev->dev.of_node; + struct omap_control_usb_platform_data *pdata = pdev->dev.platform_data; + + control_usb = devm_kzalloc(&pdev->dev, sizeof(*control_usb), + GFP_KERNEL); + if (!control_usb) { + dev_err(&pdev->dev, "unable to alloc memory for control usb\n"); + return -ENOMEM; + } + + if (np) { + of_property_read_u32(np, "ti,type", &control_usb->type); + } else if (pdata) { + control_usb->type = pdata->type; + } else { + dev_err(&pdev->dev, "no pdata present\n"); + return -EINVAL; + } + + control_usb->dev = &pdev->dev; + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "control_dev_conf"); + control_usb->dev_conf = devm_request_and_ioremap(&pdev->dev, res); + if (!control_usb->dev_conf) { + dev_err(&pdev->dev, "Failed to obtain io memory\n"); + return -EADDRNOTAVAIL; + } + + if (control_usb->type == OMAP_CTRL_DEV_TYPE1) { + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "otghs_control"); + control_usb->otghs_control = devm_request_and_ioremap( + &pdev->dev, res); + if (!control_usb->otghs_control) { + dev_err(&pdev->dev, "Failed to obtain io memory\n"); + return -EADDRNOTAVAIL; + } + } + + if (control_usb->type == OMAP_CTRL_DEV_TYPE2) { + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "phy_power_usb"); + control_usb->phy_power = devm_request_and_ioremap( + &pdev->dev, res); + if (!control_usb->phy_power) { + dev_dbg(&pdev->dev, "Failed to obtain io memory\n"); + return -EADDRNOTAVAIL; + } + + control_usb->sys_clk = devm_clk_get(control_usb->dev, + "sys_clkin"); + if (IS_ERR(control_usb->sys_clk)) { + pr_err("%s: unable to get sys_clkin\n", __func__); + return -EINVAL; + } + } + + + dev_set_drvdata(control_usb->dev, control_usb); + + return 0; +} + +#ifdef CONFIG_OF +static const struct of_device_id omap_control_usb_id_table[] = { + { .compatible = "ti,omap-control-usb" }, + {} +}; +MODULE_DEVICE_TABLE(of, omap_control_usb_id_table); +#endif + +static struct platform_driver omap_control_usb_driver = { + .probe = omap_control_usb_probe, + .driver = { + .name = "omap-control-usb", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(omap_control_usb_id_table), + }, +}; + +static int __init omap_control_usb_init(void) +{ + return platform_driver_register(&omap_control_usb_driver); +} +subsys_initcall(omap_control_usb_init); + +static void __exit omap_control_usb_exit(void) +{ + platform_driver_unregister(&omap_control_usb_driver); +} +module_exit(omap_control_usb_exit); + +MODULE_ALIAS("platform: omap_control_usb"); +MODULE_AUTHOR("Texas Instruments Inc."); +MODULE_DESCRIPTION("OMAP Control Module USB Driver"); +MODULE_LICENSE("GPL v2"); diff --git a/include/linux/usb/omap_control_usb.h b/include/linux/usb/omap_control_usb.h new file mode 100644 index 000000000000..f306db7149ca --- /dev/null +++ b/include/linux/usb/omap_control_usb.h @@ -0,0 +1,92 @@ +/* + * omap_control_usb.h - Header file for the USB part of control module. + * + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Author: Kishon Vijay Abraham I <kishon@ti.com> + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef __OMAP_CONTROL_USB_H__ +#define __OMAP_CONTROL_USB_H__ + +struct omap_control_usb { + struct device *dev; + + u32 __iomem *dev_conf; + u32 __iomem *otghs_control; + u32 __iomem *phy_power; + + struct clk *sys_clk; + + u32 type; +}; + +struct omap_control_usb_platform_data { + u8 type; +}; + +enum omap_control_usb_mode { + USB_MODE_UNDEFINED = 0, + USB_MODE_HOST, + USB_MODE_DEVICE, + USB_MODE_DISCONNECT, +}; + +/* To differentiate ctrl module IP having either mailbox or USB3 PHY power */ +#define OMAP_CTRL_DEV_TYPE1 0x1 +#define OMAP_CTRL_DEV_TYPE2 0x2 + +#define OMAP_CTRL_DEV_PHY_PD BIT(0) + +#define OMAP_CTRL_DEV_AVALID BIT(0) +#define OMAP_CTRL_DEV_BVALID BIT(1) +#define OMAP_CTRL_DEV_VBUSVALID BIT(2) +#define OMAP_CTRL_DEV_SESSEND BIT(3) +#define OMAP_CTRL_DEV_IDDIG BIT(4) + +#define OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK 0x003FC000 +#define OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT 0xE + +#define OMAP_CTRL_USB_PWRCTL_CLK_FREQ_MASK 0xFFC00000 +#define OMAP_CTRL_USB_PWRCTL_CLK_FREQ_SHIFT 0x16 + +#define OMAP_CTRL_USB3_PHY_TX_RX_POWERON 0x3 +#define OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF 0x0 + +#if IS_ENABLED(CONFIG_OMAP_CONTROL_USB) +extern struct device *omap_get_control_dev(void); +extern void omap_control_usb_phy_power(struct device *dev, int on); +extern void omap_control_usb3_phy_power(struct device *dev, bool on); +extern void omap_control_usb_set_mode(struct device *dev, + enum omap_control_usb_mode mode); +#else +static inline struct device *omap_get_control_dev() +{ + return ERR_PTR(-ENODEV); +} + +static inline void omap_control_usb_phy_power(struct device *dev, int on) +{ +} + +static inline void omap_control_usb3_phy_power(struct device *dev, int on) +{ +} + +static inline void omap_control_usb_set_mode(struct device *dev, + enum omap_control_usb_mode mode) +{ +} +#endif + +#endif /* __OMAP_CONTROL_USB_H__ */ |