diff options
29 files changed, 510 insertions, 65 deletions
diff --git a/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt new file mode 100644 index 000000000000..02649d8b3f5a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt @@ -0,0 +1,35 @@ +Mediatek MT6311 Regulator Driver + +Required properties: +- compatible: "mediatek,mt6311-regulator" +- reg: I2C slave address, usually 0x6b. +- regulators: List of regulators provided by this controller. It is named + to VDVFS and VBIASN. + The definition for each of these nodes is defined using the standard binding + for regulators at Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are: +BUCK: + VDVFS +LDO: + VBIASN + +Example: + mt6311: pmic@6b { + compatible = "mediatek,mt6311-regulator"; + reg = <0x6b>; + + regulators { + mt6311_vcpu_reg: VDVFS { + regulator-name = "VDVFS"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <10000>; + }; + mt6311_ldo_reg: VBIASN { + regulator-name = "VBIASN"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <800000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt index ce91f61feb12..ed936f0f34f2 100644 --- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -1,27 +1,68 @@ -pwm regulator bindings +Bindings for the Generic PWM Regulator +====================================== + +Currently supports 2 modes of operation: + +Voltage Table: When in this mode, a voltage table (See below) of + predefined voltage <=> duty-cycle values must be + provided via DT. Limitations are that the regulator can + only operate at the voltages supplied in the table. + Intermediary duty-cycle values which would normally + allow finer grained voltage selection are ignored and + rendered useless. Although more control is given to + the user if the assumptions made in continuous-voltage + mode do not reign true. + +Continuous Voltage: This mode uses the regulator's maximum and minimum + supplied voltages specified in the + regulator-{min,max}-microvolt properties to calculate + appropriate duty-cycle values. This allows for a much + more fine grained solution when compared with + voltage-table mode above. This solution does make an + assumption that a %50 duty-cycle value will cause the + regulator voltage to run at half way between the + supplied max_uV and min_uV values. Required properties: -- compatible: Should be "pwm-regulator" -- pwms: OF device-tree PWM specification (see PWM binding pwm.txt) -- voltage-table: voltage and duty table, include 2 members in each set of - brackets, first one is voltage(unit: uv), the next is duty(unit: percent) +-------------------- +- compatible: Should be "pwm-regulator" + +- pwms: PWM specification (See: ../pwm/pwm.txt) + +Only required for Voltage Table Mode: +- voltage-table: Voltage and Duty-Cycle table consisting of 2 cells + First cell is voltage in microvolts (uV) + Second cell is duty-cycle in percent (%) + +NB: To be clear, if voltage-table is provided, then the device will be used +in Voltage Table Mode. If no voltage-table is provided, then the device will +be used in Continuous Voltage Mode. -Any property defined as part of the core regulator binding defined in -regulator.txt can also be used. +Any property defined as part of the core regulator binding can also be used. +(See: ../regulator/regulator.txt) -Example: +Continuous Voltage Example: pwm_regulator { compatible = "pwm-regulator; pwms = <&pwm1 0 8448 0>; + regulator-min-microvolt = <1016000>; + regulator-max-microvolt = <1114000>; + regulator-name = "vdd_logic"; + }; +Voltage Table Example: + pwm_regulator { + compatible = "pwm-regulator; + pwms = <&pwm1 0 8448 0>; + regulator-min-microvolt = <1016000>; + regulator-max-microvolt = <1114000>; + regulator-name = "vdd_logic"; + + /* Voltage Duty-Cycle */ voltage-table = <1114000 0>, <1095000 10>, <1076000 20>, <1056000 30>, <1036000 40>, <1016000 50>; - - regulator-min-microvolt = <1016000>; - regulator-max-microvolt = <1114000>; - regulator-name = "vdd_logic"; }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index db88feb28c03..24bd422cecd5 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -42,6 +42,7 @@ Optional properties: - regulator-system-load: Load in uA present on regulator that is not captured by any consumer request. - regulator-pull-down: Enable pull down resistor when the regulator is disabled. +- regulator-over-current-protection: Enable over current protection. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig index a7b81f0185b5..f3cdf7a4e487 100644 --- a/drivers/regulator/Kconfig +++ b/drivers/regulator/Kconfig @@ -443,6 +443,15 @@ config REGULATOR_MC13892 Say y here to support the regulators found on the Freescale MC13892 PMIC. +config REGULATOR_MT6311 + tristate "MediaTek MT6311 PMIC" + depends on I2C + help + Say y here to select this option to enable the power regulator of + MediaTek MT6311 PMIC. + This driver supports the control of different power rails of device + through regulator interface. + config REGULATOR_MT6397 tristate "MediaTek MT6397 PMIC" depends on MFD_MT6397 diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile index 6429e629dcb6..8bc702910320 100644 --- a/drivers/regulator/Makefile +++ b/drivers/regulator/Makefile @@ -59,6 +59,7 @@ obj-$(CONFIG_REGULATOR_MAX77802) += max77802.o obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o +obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o obj-$(CONFIG_REGULATOR_MT6397) += mt6397-regulator.o obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o diff --git a/drivers/regulator/act8865-regulator.c b/drivers/regulator/act8865-regulator.c index 2ff73d72ca34..896db168e4bd 100644 --- a/drivers/regulator/act8865-regulator.c +++ b/drivers/regulator/act8865-regulator.c @@ -530,7 +530,6 @@ MODULE_DEVICE_TABLE(i2c, act8865_ids); static struct i2c_driver act8865_pmic_driver = { .driver = { .name = "act8865", - .owner = THIS_MODULE, }, .probe = act8865_pmic_probe, .id_table = act8865_ids, diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c index 4315476540c4..de9f272a0faf 100644 --- a/drivers/regulator/core.c +++ b/drivers/regulator/core.c @@ -1091,6 +1091,15 @@ static int set_machine_constraints(struct regulator_dev *rdev, } } + if (rdev->constraints->over_current_protection + && ops->set_over_current_protection) { + ret = ops->set_over_current_protection(rdev); + if (ret < 0) { + rdev_err(rdev, "failed to set over current protection\n"); + goto out; + } + } + print_constraints(rdev); return 0; out: diff --git a/drivers/regulator/da9210-regulator.c b/drivers/regulator/da9210-regulator.c index 8e39f7457bc3..b3517830edb6 100644 --- a/drivers/regulator/da9210-regulator.c +++ b/drivers/regulator/da9210-regulator.c @@ -259,7 +259,6 @@ MODULE_DEVICE_TABLE(i2c, da9210_i2c_id); static struct i2c_driver da9210_regulator_driver = { .driver = { .name = "da9210", - .owner = THIS_MODULE, }, .probe = da9210_i2c_probe, .id_table = da9210_i2c_id, diff --git a/drivers/regulator/da9211-regulator.c b/drivers/regulator/da9211-regulator.c index 0858100d2d03..04ef65b7eb3d 100644 --- a/drivers/regulator/da9211-regulator.c +++ b/drivers/regulator/da9211-regulator.c @@ -512,7 +512,6 @@ MODULE_DEVICE_TABLE(of, da9211_dt_ids); static struct i2c_driver da9211_regulator_driver = { .driver = { .name = "da9211", - .owner = THIS_MODULE, .of_match_table = of_match_ptr(da9211_dt_ids), }, .probe = da9211_i2c_probe, diff --git a/drivers/regulator/isl6271a-regulator.c b/drivers/regulator/isl6271a-regulator.c index 6e5da95fa025..4abd8e9c81e5 100644 --- a/drivers/regulator/isl6271a-regulator.c +++ b/drivers/regulator/isl6271a-regulator.c @@ -156,7 +156,6 @@ MODULE_DEVICE_TABLE(i2c, isl6271a_id); static struct i2c_driver isl6271a_i2c_driver = { .driver = { .name = "isl6271a", - .owner = THIS_MODULE, }, .probe = isl6271a_probe, .id_table = isl6271a_id, diff --git a/drivers/regulator/isl9305.c b/drivers/regulator/isl9305.c index e02e9a9dddbd..257c1943e753 100644 --- a/drivers/regulator/isl9305.c +++ b/drivers/regulator/isl9305.c @@ -196,7 +196,6 @@ MODULE_DEVICE_TABLE(i2c, isl9305_i2c_id); static struct i2c_driver isl9305_regulator_driver = { .driver = { .name = "isl9305", - .owner = THIS_MODULE, .of_match_table = of_match_ptr(isl9305_dt_ids), }, .probe = isl9305_i2c_probe, diff --git a/drivers/regulator/lp3971.c b/drivers/regulator/lp3971.c index 66fd2330dca0..15c25c622edf 100644 --- a/drivers/regulator/lp3971.c +++ b/drivers/regulator/lp3971.c @@ -452,7 +452,6 @@ MODULE_DEVICE_TABLE(i2c, lp3971_i2c_id); static struct i2c_driver lp3971_i2c_driver = { .driver = { .name = "LP3971", - .owner = THIS_MODULE, }, .probe = lp3971_i2c_probe, .id_table = lp3971_i2c_id, diff --git a/drivers/regulator/lp3972.c b/drivers/regulator/lp3972.c index aea485afcc1a..3a7e96e2c7b3 100644 --- a/drivers/regulator/lp3972.c +++ b/drivers/regulator/lp3972.c @@ -550,7 +550,6 @@ MODULE_DEVICE_TABLE(i2c, lp3972_i2c_id); static struct i2c_driver lp3972_i2c_driver = { .driver = { .name = "lp3972", - .owner = THIS_MODULE, }, .probe = lp3972_i2c_probe, .id_table = lp3972_i2c_id, diff --git a/drivers/regulator/lp872x.c b/drivers/regulator/lp872x.c index 8702e7384af7..e5af07208f9d 100644 --- a/drivers/regulator/lp872x.c +++ b/drivers/regulator/lp872x.c @@ -961,7 +961,6 @@ MODULE_DEVICE_TABLE(i2c, lp872x_ids); static struct i2c_driver lp872x_driver = { .driver = { .name = "lp872x", - .owner = THIS_MODULE, .of_match_table = of_match_ptr(lp872x_dt_ids), }, .probe = lp872x_probe, diff --git a/drivers/regulator/ltc3589.c b/drivers/regulator/ltc3589.c index cc22ac66c8fd..972c386b2690 100644 --- a/drivers/regulator/ltc3589.c +++ b/drivers/regulator/ltc3589.c @@ -542,7 +542,6 @@ MODULE_DEVICE_TABLE(i2c, ltc3589_i2c_id); static struct i2c_driver ltc3589_driver = { .driver = { .name = DRIVER_NAME, - .owner = THIS_MODULE, }, .probe = ltc3589_probe, .id_table = ltc3589_i2c_id, diff --git a/drivers/regulator/max1586.c b/drivers/regulator/max1586.c index d2a8c64cae42..2c1228d5796a 100644 --- a/drivers/regulator/max1586.c +++ b/drivers/regulator/max1586.c @@ -304,7 +304,6 @@ static struct i2c_driver max1586_pmic_driver = { .probe = max1586_pmic_probe, .driver = { .name = "max1586", - .owner = THIS_MODULE, .of_match_table = of_match_ptr(max1586_of_match), }, .id_table = max1586_id, diff --git a/drivers/regulator/max8660.c b/drivers/regulator/max8660.c index 4071d74fa828..b87f62dd484e 100644 --- a/drivers/regulator/max8660.c +++ b/drivers/regulator/max8660.c @@ -518,7 +518,6 @@ static struct i2c_driver max8660_driver = { .probe = max8660_probe, .driver = { .name = "max8660", - .owner = THIS_MODULE, }, .id_table = max8660_id, }; diff --git a/drivers/regulator/max8973-regulator.c b/drivers/regulator/max8973-regulator.c index 8857cc02d9a8..5b75b7c2e3ea 100644 --- a/drivers/regulator/max8973-regulator.c +++ b/drivers/regulator/max8973-regulator.c @@ -732,7 +732,6 @@ static struct i2c_driver max8973_i2c_driver = { .driver = { .name = "max8973", .of_match_table = of_max8973_match_tbl, - .owner = THIS_MODULE, }, .probe = max8973_probe, .id_table = max8973_id, diff --git a/drivers/regulator/mt6311-regulator.c b/drivers/regulator/mt6311-regulator.c new file mode 100644 index 000000000000..02c4e5feca8e --- /dev/null +++ b/drivers/regulator/mt6311-regulator.c @@ -0,0 +1,179 @@ +/* + * Copyright (c) 2015 MediaTek Inc. + * Author: Henry Chen <henryc.chen@mediatek.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/err.h> +#include <linux/gpio.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/of_regulator.h> +#include <linux/regulator/mt6311.h> +#include <linux/slab.h> +#include "mt6311-regulator.h" + +static const struct regmap_config mt6311_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = MT6311_FQMTR_CON4, +}; + +/* Default limits measured in millivolts and milliamps */ +#define MT6311_MIN_UV 600000 +#define MT6311_MAX_UV 1393750 +#define MT6311_STEP_UV 6250 + +static const struct regulator_linear_range buck_volt_range[] = { + REGULATOR_LINEAR_RANGE(MT6311_MIN_UV, 0, 0x7f, MT6311_STEP_UV), +}; + +static const struct regulator_ops mt6311_buck_ops = { + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_time_sel = regulator_set_voltage_time_sel, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, +}; + +static const struct regulator_ops mt6311_ldo_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, +}; + +#define MT6311_BUCK(_id) \ +{\ + .name = #_id,\ + .ops = &mt6311_buck_ops,\ + .of_match = of_match_ptr(#_id),\ + .regulators_node = of_match_ptr("regulators"),\ + .type = REGULATOR_VOLTAGE,\ + .id = MT6311_ID_##_id,\ + .n_voltages = (MT6311_MAX_UV - MT6311_MIN_UV) / MT6311_STEP_UV + 1,\ + .min_uV = MT6311_MIN_UV,\ + .uV_step = MT6311_STEP_UV,\ + .owner = THIS_MODULE,\ + .linear_ranges = buck_volt_range, \ + .n_linear_ranges = ARRAY_SIZE(buck_volt_range), \ + .enable_reg = MT6311_VDVFS11_CON9,\ + .enable_mask = MT6311_PMIC_VDVFS11_EN_MASK,\ + .vsel_reg = MT6311_VDVFS11_CON12,\ + .vsel_mask = MT6311_PMIC_VDVFS11_VOSEL_MASK,\ +} + +#define MT6311_LDO(_id) \ +{\ + .name = #_id,\ + .ops = &mt6311_ldo_ops,\ + .of_match = of_match_ptr(#_id),\ + .regulators_node = of_match_ptr("regulators"),\ + .type = REGULATOR_VOLTAGE,\ + .id = MT6311_ID_##_id,\ + .owner = THIS_MODULE,\ + .enable_reg = MT6311_LDO_CON3,\ + .enable_mask = MT6311_PMIC_RG_VBIASN_EN_MASK,\ +} + +static const struct regulator_desc mt6311_regulators[] = { + MT6311_BUCK(VDVFS), + MT6311_LDO(VBIASN), +}; + +/* + * I2C driver interface functions + */ +static int mt6311_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + struct regulator_config config = { }; + struct regulator_dev *rdev; + struct regmap *regmap; + int i, ret; + unsigned int data; + + regmap = devm_regmap_init_i2c(i2c, &mt6311_regmap_config); + if (IS_ERR(regmap)) { + ret = PTR_ERR(regmap); + dev_err(&i2c->dev, "Failed to allocate register map: %d\n", + ret); + return ret; + } + + ret = regmap_read(regmap, MT6311_SWCID, &data); + if (ret < 0) { + dev_err(&i2c->dev, "Failed to read DEVICE_ID reg: %d\n", ret); + return ret; + } + + switch (data) { + case MT6311_E1_CID_CODE: + case MT6311_E2_CID_CODE: + case MT6311_E3_CID_CODE: + break; + default: + dev_err(&i2c->dev, "Unsupported device id = 0x%x.\n", data); + return -ENODEV; + } + + for (i = 0; i < MT6311_MAX_REGULATORS; i++) { + config.dev = &i2c->dev; + config.regmap = regmap; + + rdev = devm_regulator_register(&i2c->dev, + &mt6311_regulators[i], &config); + if (IS_ERR(rdev)) { + dev_err(&i2c->dev, + "Failed to register MT6311 regulator\n"); + return PTR_ERR(rdev); + } + } + + return 0; +} + +static const struct i2c_device_id mt6311_i2c_id[] = { + {"mt6311", 0}, + {}, +}; +MODULE_DEVICE_TABLE(i2c, mt6311_i2c_id); + +#ifdef CONFIG_OF +static const struct of_device_id mt6311_dt_ids[] = { + { .compatible = "mediatek,mt6311-regulator", + .data = &mt6311_i2c_id[0] }, + {}, +}; +MODULE_DEVICE_TABLE(of, mt6311_dt_ids); +#endif + +static struct i2c_driver mt6311_regulator_driver = { + .driver = { + .name = "mt6311", + .of_match_table = of_match_ptr(mt6311_dt_ids), + }, + .probe = mt6311_i2c_probe, + .id_table = mt6311_i2c_id, +}; + +module_i2c_driver(mt6311_regulator_driver); + +MODULE_AUTHOR("Henry Chen <henryc.chen@mediatek.com>"); +MODULE_DESCRIPTION("Regulator device driver for Mediatek MT6311"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/regulator/mt6311-regulator.h b/drivers/regulator/mt6311-regulator.h new file mode 100644 index 000000000000..5218db46a798 --- /dev/null +++ b/drivers/regulator/mt6311-regulator.h @@ -0,0 +1,65 @@ +/* + * Copyright (c) 2015 MediaTek Inc. + * Author: Henry Chen <henryc.chen@mediatek.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __MT6311_REGULATOR_H__ +#define __MT6311_REGULATOR_H__ + +#define MT6311_SWCID 0x01 + +#define MT6311_TOP_INT_CON 0x18 +#define MT6311_TOP_INT_MON 0x19 + +#define MT6311_VDVFS11_CON0 0x87 +#define MT6311_VDVFS11_CON7 0x88 +#define MT6311_VDVFS11_CON8 0x89 +#define MT6311_VDVFS11_CON9 0x8A +#define MT6311_VDVFS11_CON10 0x8B +#define MT6311_VDVFS11_CON11 0x8C +#define MT6311_VDVFS11_CON12 0x8D +#define MT6311_VDVFS11_CON13 0x8E +#define MT6311_VDVFS11_CON14 0x8F +#define MT6311_VDVFS11_CON15 0x90 +#define MT6311_VDVFS11_CON16 0x91 +#define MT6311_VDVFS11_CON17 0x92 +#define MT6311_VDVFS11_CON18 0x93 +#define MT6311_VDVFS11_CON19 0x94 + +#define MT6311_LDO_CON0 0xCC +#define MT6311_LDO_OCFB0 0xCD +#define MT6311_LDO_CON2 0xCE +#define MT6311_LDO_CON3 0xCF +#define MT6311_LDO_CON4 0xD0 +#define MT6311_FQMTR_CON0 0xD1 +#define MT6311_FQMTR_CON1 0xD2 +#define MT6311_FQMTR_CON2 0xD3 +#define MT6311_FQMTR_CON3 0xD4 +#define MT6311_FQMTR_CON4 0xD5 + +#define MT6311_PMIC_RG_INT_POL_MASK 0x1 +#define MT6311_PMIC_RG_INT_EN_MASK 0x2 +#define MT6311_PMIC_RG_BUCK_OC_INT_STATUS_MASK 0x10 + +#define MT6311_PMIC_VDVFS11_EN_CTRL_MASK 0x1 +#define MT6311_PMIC_VDVFS11_VOSEL_CTRL_MASK 0x2 +#define MT6311_PMIC_VDVFS11_EN_SEL_MASK 0x3 +#define MT6311_PMIC_VDVFS11_VOSEL_SEL_MASK 0xc +#define MT6311_PMIC_VDVFS11_EN_MASK 0x1 +#define MT6311_PMIC_VDVFS11_VOSEL_MASK 0x7F +#define MT6311_PMIC_VDVFS11_VOSEL_ON_MASK 0x7F +#define MT6311_PMIC_VDVFS11_VOSEL_SLEEP_MASK 0x7F +#define MT6311_PMIC_NI_VDVFS11_VOSEL_MASK 0x7F + +#define MT6311_PMIC_RG_VBIASN_EN_MASK 0x1 + +#endif diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c index b1c485b24ab2..250700c853bf 100644 --- a/drivers/regulator/of_regulator.c +++ b/drivers/regulator/of_regulator.c @@ -107,6 +107,9 @@ static void of_get_regulation_constraints(struct device_node *np, if (!of_property_read_u32(np, "regulator-system-load", &pval)) constraints->system_load = pval; + constraints->over_current_protection = of_property_read_bool(np, + "regulator-over-current-protection"); + for (i = 0; i < ARRAY_SIZE(regulator_states); i++) { switch (i) { case PM_SUSPEND_MEM: diff --git a/drivers/regulator/pfuze100-regulator.c b/drivers/regulator/pfuze100-regulator.c index 8cc8d1877c44..2a44e5dd9c2a 100644 --- a/drivers/regulator/pfuze100-regulator.c +++ b/drivers/regulator/pfuze100-regulator.c @@ -643,7 +643,6 @@ static struct i2c_driver pfuze_driver = { .id_table = pfuze_device_id, .driver = { .name = "pfuze100-regulator", - .owner = THIS_MODULE, .of_match_table = pfuze_dt_ids, }, .probe = pfuze100_regulator_probe, @@ -653,4 +652,3 @@ module_i2c_driver(pfuze_driver); MODULE_AUTHOR("Robin Gong <b38343@freescale.com>"); MODULE_DESCRIPTION("Regulator Driver for Freescale PFUZE100/PFUZE200 PMIC"); MODULE_LICENSE("GPL v2"); -MODULE_ALIAS("i2c:pfuze100-regulator"); diff --git a/drivers/regulator/pwm-regulator.c b/drivers/regulator/pwm-regulator.c index ffa96124a5e7..fc3166dfcbfa 100644 --- a/drivers/regulator/pwm-regulator.c +++ b/drivers/regulator/pwm-regulator.c @@ -10,6 +10,7 @@ * published by the Free Software Foundation. */ +#include <linux/delay.h> #include <linux/module.h> #include <linux/init.h> #include <linux/err.h> @@ -21,9 +22,15 @@ #include <linux/pwm.h> struct pwm_regulator_data { - struct pwm_voltages *duty_cycle_table; + /* Shared */ struct pwm_device *pwm; + + /* Voltage table */ + struct pwm_voltages *duty_cycle_table; int state; + + /* Continuous voltage */ + int volt_uV; }; struct pwm_voltages { @@ -31,6 +38,9 @@ struct pwm_voltages { unsigned int dutycycle; }; +/** + * Voltage table call-backs + */ static int pwm_regulator_get_voltage_sel(struct regulator_dev *rdev) { struct pwm_regulator_data *drvdata = rdev_get_drvdata(rdev); @@ -79,29 +89,129 @@ static int pwm_regulator_list_voltage(struct regulator_dev *rdev, return drvdata->duty_cycle_table[selector].uV; } -static struct regulator_ops pwm_regulator_voltage_ops = { +/** + * Continuous voltage call-backs + */ +static int pwm_voltage_to_duty_cycle_percentage(struct regulator_dev *rdev, int req_uV) +{ + int min_uV = rdev->constraints->min_uV; + int max_uV = rdev->constraints->max_uV; + int diff = max_uV - min_uV; + + return 100 - (((req_uV * 100) - (min_uV * 100)) / diff); +} + +static int pwm_regulator_get_voltage(struct regulator_dev *rdev) +{ + struct pwm_regulator_data *drvdata = rdev_get_drvdata(rdev); + + return drvdata->volt_uV; +} + +static int pwm_regulator_set_voltage(struct regulator_dev *rdev, + int min_uV, int max_uV, + unsigned *selector) +{ + struct pwm_regulator_data *drvdata = rdev_get_drvdata(rdev); + unsigned int ramp_delay = rdev->constraints->ramp_delay; + unsigned int period = pwm_get_period(drvdata->pwm); + int duty_cycle; + int ret; + + duty_cycle = pwm_voltage_to_duty_cycle_percentage(rdev, min_uV); + + ret = pwm_config(drvdata->pwm, (period / 100) * duty_cycle, period); + if (ret) { + dev_err(&rdev->dev, "Failed to configure PWM\n"); + return ret; + } + + ret = pwm_enable(drvdata->pwm); + if (ret) { + dev_err(&rdev->dev, "Failed to enable PWM\n"); + return ret; + } + drvdata->volt_uV = min_uV; + + /* Delay required by PWM regulator to settle to the new voltage */ + usleep_range(ramp_delay, ramp_delay + 1000); + + return 0; +} + +static struct regulator_ops pwm_regulator_voltage_table_ops = { .set_voltage_sel = pwm_regulator_set_voltage_sel, .get_voltage_sel = pwm_regulator_get_voltage_sel, .list_voltage = pwm_regulator_list_voltage, .map_voltage = regulator_map_voltage_iterate, }; +static struct regulator_ops pwm_regulator_voltage_continuous_ops = { + .get_voltage = pwm_regulator_get_voltage, + .set_voltage = pwm_regulator_set_voltage, +}; + static struct regulator_desc pwm_regulator_desc = { .name = "pwm-regulator", - .ops = &pwm_regulator_voltage_ops, .type = REGULATOR_VOLTAGE, .owner = THIS_MODULE, .supply_name = "pwm", }; +static int pwm_regulator_init_table(struct platform_device *pdev, + struct pwm_regulator_data *drvdata) +{ + struct device_node *np = pdev->dev.of_node; + struct pwm_voltages *duty_cycle_table; + unsigned int length = 0; + int ret; + + of_find_property(np, "voltage-table", &length); + + if ((length < sizeof(*duty_cycle_table)) || + (length % sizeof(*duty_cycle_table))) { + dev_err(&pdev->dev, + "voltage-table length(%d) is invalid\n", + length); + return -EINVAL; + } + + duty_cycle_table = devm_kzalloc(&pdev->dev, length, GFP_KERNEL); + if (!duty_cycle_table) + return -ENOMEM; + + ret = of_property_read_u32_array(np, "voltage-table", + (u32 *)duty_cycle_table, + length / sizeof(u32)); + if (ret) { + dev_err(&pdev->dev, "Failed to read voltage-table\n"); + return ret; + } + + drvdata->duty_cycle_table = duty_cycle_table; + pwm_regulator_desc.ops = &pwm_regulator_voltage_table_ops; + pwm_regulator_desc.n_voltages = length / sizeof(*duty_cycle_table); + + return 0; +} + +static int pwm_regulator_init_continuous(struct platform_device *pdev, + struct pwm_regulator_data *drvdata) +{ + pwm_regulator_desc.ops = &pwm_regulator_voltage_continuous_ops; + pwm_regulator_desc.continuous_voltage_range = true; + + return 0; +} + static int pwm_regulator_probe(struct platform_device *pdev) { + const struct regulator_init_data *init_data; struct pwm_regulator_data *drvdata; - struct property *prop; struct regulator_dev *regulator; struct regulator_config config = { }; struct device_node *np = pdev->dev.of_node; - int length, ret; + int ret; if (!np) { dev_err(&pdev->dev, "Device Tree node missing\n"); @@ -112,44 +222,22 @@ static int pwm_regulator_probe(struct platform_device *pdev) if (!drvdata) return -ENOMEM; - /* determine the number of voltage-table */ - prop = of_find_property(np, "voltage-table", &length); - if (!prop) { - dev_err(&pdev->dev, "No voltage-table\n"); - return -EINVAL; - } - - if ((length < sizeof(*drvdata->duty_cycle_table)) || - (length % sizeof(*drvdata->duty_cycle_table))) { - dev_err(&pdev->dev, "voltage-table length(%d) is invalid\n", - length); - return -EINVAL; - } - - pwm_regulator_desc.n_voltages = length / sizeof(*drvdata->duty_cycle_table); - - drvdata->duty_cycle_table = devm_kzalloc(&pdev->dev, - length, GFP_KERNEL); - if (!drvdata->duty_cycle_table) - return -ENOMEM; - - /* read voltage table from DT property */ - ret = of_property_read_u32_array(np, "voltage-table", - (u32 *)drvdata->duty_cycle_table, - length / sizeof(u32)); - if (ret < 0) { - dev_err(&pdev->dev, "read voltage-table failed\n"); + if (of_find_property(np, "voltage-table", NULL)) + ret = pwm_regulator_init_table(pdev, drvdata); + else + ret = pwm_regulator_init_continuous(pdev, drvdata); + if (ret) return ret; - } - config.init_data = of_get_regulator_init_data(&pdev->dev, np, - &pwm_regulator_desc); - if (!config.init_data) + init_data = of_get_regulator_init_data(&pdev->dev, np, + &pwm_regulator_desc); + if (!init_data) return -ENOMEM; config.of_node = np; config.dev = &pdev->dev; config.driver_data = drvdata; + config.init_data = init_data; drvdata->pwm = devm_pwm_get(&pdev->dev, NULL); if (IS_ERR(drvdata->pwm)) { diff --git a/drivers/regulator/tps51632-regulator.c b/drivers/regulator/tps51632-regulator.c index c213e37eb69e..572816e30095 100644 --- a/drivers/regulator/tps51632-regulator.c +++ b/drivers/regulator/tps51632-regulator.c @@ -362,7 +362,6 @@ MODULE_DEVICE_TABLE(i2c, tps51632_id); static struct i2c_driver tps51632_i2c_driver = { .driver = { .name = "tps51632", - .owner = THIS_MODULE, .of_match_table = of_match_ptr(tps51632_of_match), }, .probe = tps51632_probe, diff --git a/drivers/regulator/tps62360-regulator.c b/drivers/regulator/tps62360-regulator.c index a1fd626c6c96..f6a6d36a6533 100644 --- a/drivers/regulator/tps62360-regulator.c +++ b/drivers/regulator/tps62360-regulator.c @@ -515,7 +515,6 @@ MODULE_DEVICE_TABLE(i2c, tps62360_id); static struct i2c_driver tps62360_i2c_driver = { .driver = { .name = "tps62360", - .owner = THIS_MODULE, .of_match_table = of_match_ptr(tps62360_of_match), }, .probe = tps62360_probe, diff --git a/drivers/regulator/tps65023-regulator.c b/drivers/regulator/tps65023-regulator.c index b941e564b3f3..5cc19b44974a 100644 --- a/drivers/regulator/tps65023-regulator.c +++ b/drivers/regulator/tps65023-regulator.c @@ -410,7 +410,6 @@ MODULE_DEVICE_TABLE(i2c, tps_65023_id); static struct i2c_driver tps_65023_i2c_driver = { .driver = { .name = "tps65023", - .owner = THIS_MODULE, }, .probe = tps_65023_probe, .id_table = tps_65023_id, diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h index 4db9fbe4889d..45932228cbf5 100644 --- a/include/linux/regulator/driver.h +++ b/include/linux/regulator/driver.h @@ -148,6 +148,7 @@ struct regulator_ops { int (*get_current_limit) (struct regulator_dev *); int (*set_input_current_limit) (struct regulator_dev *, int lim_uA); + int (*set_over_current_protection) (struct regulator_dev *); /* enable/disable regulator */ int (*enable) (struct regulator_dev *); diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h index b11be1260129..a1067d0b3991 100644 --- a/include/linux/regulator/machine.h +++ b/include/linux/regulator/machine.h @@ -147,6 +147,7 @@ struct regulation_constraints { unsigned ramp_disable:1; /* disable ramp delay */ unsigned soft_start:1; /* ramp voltage slowly */ unsigned pull_down:1; /* pull down resistor when regulator off */ + unsigned over_current_protection:1; /* auto disable on over current */ }; /** diff --git a/include/linux/regulator/mt6311.h b/include/linux/regulator/mt6311.h new file mode 100644 index 000000000000..8473259395b6 --- /dev/null +++ b/include/linux/regulator/mt6311.h @@ -0,0 +1,29 @@ +/* + * Copyright (c) 2015 MediaTek Inc. + * Author: Henry Chen <henryc.chen@mediatek.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __LINUX_REGULATOR_MT6311_H +#define __LINUX_REGULATOR_MT6311_H + +#define MT6311_MAX_REGULATORS 2 + +enum { + MT6311_ID_VDVFS = 0, + MT6311_ID_VBIASN, +}; + +#define MT6311_E1_CID_CODE 0x10 +#define MT6311_E2_CID_CODE 0x20 +#define MT6311_E3_CID_CODE 0x30 + +#endif /* __LINUX_REGULATOR_MT6311_H */ |