diff options
| -rw-r--r-- | arch/x86/include/asm/smp.h | 3 | ||||
| -rw-r--r-- | include/linux/smp.h | 45 |
2 files changed, 33 insertions, 15 deletions
diff --git a/arch/x86/include/asm/smp.h b/arch/x86/include/asm/smp.h index da545df207b2..0d3fe060a44f 100644 --- a/arch/x86/include/asm/smp.h +++ b/arch/x86/include/asm/smp.h @@ -162,7 +162,8 @@ __visible void smp_call_function_single_interrupt(struct pt_regs *r); * from the initial startup. We map APIC_BASE very early in page_setup(), * so this is correct in the x86 case. */ -#define raw_smp_processor_id() (this_cpu_read(cpu_number)) +#define raw_smp_processor_id() this_cpu_read(cpu_number) +#define __smp_processor_id() __this_cpu_read(cpu_number) #ifdef CONFIG_X86_32 extern int safe_smp_processor_id(void); diff --git a/include/linux/smp.h b/include/linux/smp.h index a56f08ff3097..aa9e5e82d8c3 100644 --- a/include/linux/smp.h +++ b/include/linux/smp.h @@ -181,29 +181,46 @@ static inline int get_boot_cpu_id(void) #endif /* !SMP */ -/* - * smp_processor_id(): get the current CPU ID. +/** + * raw_processor_id() - get the current (unstable) CPU id + * + * For then you know what you are doing and need an unstable + * CPU id. + */ + +/** + * smp_processor_id() - get the current (stable) CPU id + * + * This is the normal accessor to the CPU id and should be used + * whenever possible. + * + * The CPU id is stable when: * - * if DEBUG_PREEMPT is enabled then we check whether it is - * used in a preemption-safe way. (smp_processor_id() is safe - * if it's used in a preemption-off critical section, or in - * a thread that is bound to the current CPU.) + * - IRQs are disabled; + * - preemption is disabled; + * - the task is CPU affine. * - * NOTE: raw_smp_processor_id() is for internal use only - * (smp_processor_id() is the preferred variant), but in rare - * instances it might also be used to turn off false positives - * (i.e. smp_processor_id() use that the debugging code reports but - * which use for some reason is legal). Don't use this to hack around - * the warning message, as your code might not work under PREEMPT. + * When CONFIG_DEBUG_PREEMPT; we verify these assumption and WARN + * when smp_processor_id() is used when the CPU id is not stable. */ + +/* + * Allow the architecture to differentiate between a stable and unstable read. + * For example, x86 uses an IRQ-safe asm-volatile read for the unstable but a + * regular asm read for the stable. + */ +#ifndef __smp_processor_id +#define __smp_processor_id(x) raw_smp_processor_id(x) +#endif + #ifdef CONFIG_DEBUG_PREEMPT extern unsigned int debug_smp_processor_id(void); # define smp_processor_id() debug_smp_processor_id() #else -# define smp_processor_id() raw_smp_processor_id() +# define smp_processor_id() __smp_processor_id() #endif -#define get_cpu() ({ preempt_disable(); smp_processor_id(); }) +#define get_cpu() ({ preempt_disable(); __smp_processor_id(); }) #define put_cpu() preempt_enable() /* |