diff options
Diffstat (limited to 'Documentation/ABI/testing/sysfs-bus-iio')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio | 165 |
1 files changed, 164 insertions, 1 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index c551301b33f1..6ba34c0d9789 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -79,6 +79,11 @@ Description: * "accel-base" * "accel-display" + For devices where an accelerometer is housed in the swivel camera subassembly + (for AR application), the following standardized label is used: + + * "accel-camera" + What: /sys/bus/iio/devices/iio:deviceX/current_timestamp_clock KernelVersion: 4.5 Contact: linux-iio@vger.kernel.org @@ -102,6 +107,9 @@ Description: relevant directories. If it affects all of the above then it is to be found in the base device directory. + The stm32-timer-trigger has the additional characteristic that + a sampling_frequency of 0 is defined to stop sampling. + What: /sys/bus/iio/devices/iio:deviceX/sampling_frequency_available What: /sys/bus/iio/devices/iio:deviceX/in_intensity_sampling_frequency_available What: /sys/bus/iio/devices/iio:deviceX/in_proximity_sampling_frequency_available @@ -188,7 +196,7 @@ Description: Raw capacitance measurement from channel Y. Units after application of scale and offset are nanofarads. -What: /sys/.../iio:deviceX/in_capacitanceY-in_capacitanceZ_raw +What: /sys/.../iio:deviceX/in_capacitanceY-capacitanceZ_raw KernelVersion: 3.2 Contact: linux-iio@vger.kernel.org Description: @@ -199,6 +207,25 @@ Description: is required is a consistent labeling. Units after application of scale and offset are nanofarads. +What: /sys/.../iio:deviceX/in_capacitanceY-capacitanceZ_zeropoint +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + For differential channels, this an offset that is applied + equally to both inputs. As the reading is of the difference + between the two inputs, this should not be applied to the _raw + reading by userspace (unlike _offset) and unlike calibbias + it does not affect the differential value measured because + the effect of _zeropoint cancels out across the two inputs + that make up the differential pair. It's purpose is to bring + the individual signals, before the differential is measured, + within the measurement range of the device. The naming is + chosen because if the separate inputs that make the + differential pair are drawn on a graph in their + _raw units, this is the value that the zero point on the + measurement axis represents. It is expressed with the + same scaling as _raw. + What: /sys/bus/iio/devices/iio:deviceX/in_temp_raw What: /sys/bus/iio/devices/iio:deviceX/in_tempX_raw What: /sys/bus/iio/devices/iio:deviceX/in_temp_x_raw @@ -233,6 +260,15 @@ Description: Has all of the equivalent parameters as per voltageY. Units after application of scale and offset are m/s^2. +What: /sys/bus/iio/devices/iio:deviceX/in_accel_linear_x_raw +What: /sys/bus/iio/devices/iio:deviceX/in_accel_linear_y_raw +What: /sys/bus/iio/devices/iio:deviceX/in_accel_linear_z_raw +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + As per in_accel_X_raw attributes, but minus the + acceleration due to gravity. + What: /sys/bus/iio/devices/iio:deviceX/in_gravity_x_raw What: /sys/bus/iio/devices/iio:deviceX/in_gravity_y_raw What: /sys/bus/iio/devices/iio:deviceX/in_gravity_z_raw @@ -476,6 +512,7 @@ What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_i_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_q_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_voltage_i_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_voltage_q_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_altvoltage_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_voltage_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_calibscale @@ -1213,6 +1250,32 @@ Description: number or direction is not specified, applies to all channels of this type. +What: /sys/.../iio:deviceX/events/in_accel_mag_referenced_en +What: /sys/.../iio:deviceX/events/in_accel_mag_referenced_rising_en +What: /sys/.../iio:deviceX/events/in_accel_mag_referenced_falling_en +What: /sys/.../iio:deviceX/events/in_accel_y_mag_referenced_en +What: /sys/.../iio:deviceX/events/in_accel_y_mag_referenced_rising_en +What: /sys/.../iio:deviceX/events/in_accel_y_mag_referenced_falling_en +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + Similar to in_accel_mag[_y][_rising|_falling]_en, but the event + value is relative to a reference magnitude. The reference magnitude + includes the graviational acceleration. + +What: /sys/.../iio:deviceX/events/in_accel_mag_referenced_value +What: /sys/.../iio:deviceX/events/in_accel_mag_referenced_rising_value +What: /sys/.../iio:deviceX/events/in_accel_mag_referenced_falling_value +What: /sys/.../iio:deviceX/events/in_accel_y_mag_referenced_value +What: /sys/.../iio:deviceX/events/in_accel_y_mag_referenced_rising_value +What: /sys/.../iio:deviceX/events/in_accel_y_mag_referenced_falling_value +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + The value to which the reference magnitude of the channel is + compared. If the axis is not specified, it applies to all channels + of this type. + What: /sys/.../events/in_steps_change_en KernelVersion: 4.0 Contact: linux-iio@vger.kernel.org @@ -1252,6 +1315,10 @@ Description: Actually start the buffer capture up. Will start trigger if first device and appropriate. + Note that it might be impossible to configure other attributes, + (e.g.: events, scale, sampling rate) if they impact the currently + active buffer capture session. + What: /sys/bus/iio/devices/iio:deviceX/bufferY KernelVersion: 5.11 Contact: linux-iio@vger.kernel.org @@ -1999,3 +2066,99 @@ Description: Available range for the forced calibration value, expressed as: - a range specified as "[min step max]" + +What: /sys/bus/iio/devices/iio:deviceX/in_voltageX_sampling_frequency +What: /sys/bus/iio/devices/iio:deviceX/in_powerY_sampling_frequency +What: /sys/bus/iio/devices/iio:deviceX/in_currentZ_sampling_frequency +KernelVersion: 5.20 +Contact: linux-iio@vger.kernel.org +Description: + Some devices have separate controls of sampling frequency for + individual channels. If multiple channels are enabled in a scan, + then the sampling_frequency of the scan may be computed from the + per channel sampling frequencies. + +What: /sys/.../events/in_accel_gesture_singletap_en +What: /sys/.../events/in_accel_gesture_doubletap_en +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + Device generates an event on a single or double tap. + +What: /sys/.../events/in_accel_gesture_singletap_value +What: /sys/.../events/in_accel_gesture_doubletap_value +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + Specifies the threshold value that the device is comparing + against to generate the tap gesture event. The lower + threshold value increases the sensitivity of tap detection. + Units and the exact meaning of value are device-specific. + +What: /sys/.../events/in_accel_gesture_tap_value_available +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + Lists all available threshold values which can be used to + modify the sensitivity of the tap detection. + +What: /sys/.../events/in_accel_gesture_singletap_reset_timeout +What: /sys/.../events/in_accel_gesture_doubletap_reset_timeout +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + Specifies the timeout value in seconds for the tap detector + to not to look for another tap event after the event as + occurred. Basically the minimum quiet time between the two + single-tap's or two double-tap's. + +What: /sys/.../events/in_accel_gesture_tap_reset_timeout_available +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + Lists all available tap reset timeout values. Units in seconds. + +What: /sys/.../events/in_accel_gesture_doubletap_tap2_min_delay +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + Specifies the minimum quiet time in seconds between the two + taps of a double tap. + +What: /sys/.../events/in_accel_gesture_doubletap_tap2_min_delay_available +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + Lists all available delay values between two taps in the double + tap. Units in seconds. + +What: /sys/.../events/in_accel_gesture_tap_maxtomin_time +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + Specifies the maximum time difference allowed between upper + and lower peak of tap to consider it as the valid tap event. + Units in seconds. + +What: /sys/.../events/in_accel_gesture_tap_maxtomin_time_available +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + Lists all available time values between upper peak to lower + peak. Units in seconds. + +What: /sys/bus/iio/devices/iio:deviceX/in_rot_yaw_raw +What: /sys/bus/iio/devices/iio:deviceX/in_rot_pitch_raw +What: /sys/bus/iio/devices/iio:deviceX/in_rot_roll_raw +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + Raw (unscaled) euler angles readings. Units after + application of scale are deg. + +What: /sys/bus/iio/devices/iio:deviceX/serialnumber +KernelVersion: 6.1 +Contact: linux-iio@vger.kernel.org +Description: + An example format is 16-bytes, 2-digits-per-byte, HEX-string + representing the sensor unique ID number. |