diff options
Diffstat (limited to 'Documentation/admin-guide/cgroup-v2.rst')
| -rw-r--r-- | Documentation/admin-guide/cgroup-v2.rst | 97 |
1 files changed, 97 insertions, 0 deletions
diff --git a/Documentation/admin-guide/cgroup-v2.rst b/Documentation/admin-guide/cgroup-v2.rst index 5f1c266131b0..0fa8c0e615c2 100644 --- a/Documentation/admin-guide/cgroup-v2.rst +++ b/Documentation/admin-guide/cgroup-v2.rst @@ -1469,6 +1469,103 @@ IO Interface Files 8:16 rbytes=1459200 wbytes=314773504 rios=192 wios=353 dbytes=0 dios=0 8:0 rbytes=90430464 wbytes=299008000 rios=8950 wios=1252 dbytes=50331648 dios=3021 + io.cost.qos + A read-write nested-keyed file with exists only on the root + cgroup. + + This file configures the Quality of Service of the IO cost + model based controller (CONFIG_BLK_CGROUP_IOCOST) which + currently implements "io.weight" proportional control. Lines + are keyed by $MAJ:$MIN device numbers and not ordered. The + line for a given device is populated on the first write for + the device on "io.cost.qos" or "io.cost.model". The following + nested keys are defined. + + ====== ===================================== + enable Weight-based control enable + ctrl "auto" or "user" + rpct Read latency percentile [0, 100] + rlat Read latency threshold + wpct Write latency percentile [0, 100] + wlat Write latency threshold + min Minimum scaling percentage [1, 10000] + max Maximum scaling percentage [1, 10000] + ====== ===================================== + + The controller is disabled by default and can be enabled by + setting "enable" to 1. "rpct" and "wpct" parameters default + to zero and the controller uses internal device saturation + state to adjust the overall IO rate between "min" and "max". + + When a better control quality is needed, latency QoS + parameters can be configured. For example:: + + 8:16 enable=1 ctrl=auto rpct=95.00 rlat=75000 wpct=95.00 wlat=150000 min=50.00 max=150.0 + + shows that on sdb, the controller is enabled, will consider + the device saturated if the 95th percentile of read completion + latencies is above 75ms or write 150ms, and adjust the overall + IO issue rate between 50% and 150% accordingly. + + The lower the saturation point, the better the latency QoS at + the cost of aggregate bandwidth. The narrower the allowed + adjustment range between "min" and "max", the more conformant + to the cost model the IO behavior. Note that the IO issue + base rate may be far off from 100% and setting "min" and "max" + blindly can lead to a significant loss of device capacity or + control quality. "min" and "max" are useful for regulating + devices which show wide temporary behavior changes - e.g. a + ssd which accepts writes at the line speed for a while and + then completely stalls for multiple seconds. + + When "ctrl" is "auto", the parameters are controlled by the + kernel and may change automatically. Setting "ctrl" to "user" + or setting any of the percentile and latency parameters puts + it into "user" mode and disables the automatic changes. The + automatic mode can be restored by setting "ctrl" to "auto". + + io.cost.model + A read-write nested-keyed file with exists only on the root + cgroup. + + This file configures the cost model of the IO cost model based + controller (CONFIG_BLK_CGROUP_IOCOST) which currently + implements "io.weight" proportional control. Lines are keyed + by $MAJ:$MIN device numbers and not ordered. The line for a + given device is populated on the first write for the device on + "io.cost.qos" or "io.cost.model". The following nested keys + are defined. + + ===== ================================ + ctrl "auto" or "user" + model The cost model in use - "linear" + ===== ================================ + + When "ctrl" is "auto", the kernel may change all parameters + dynamically. When "ctrl" is set to "user" or any other + parameters are written to, "ctrl" become "user" and the + automatic changes are disabled. + + When "model" is "linear", the following model parameters are + defined. + + ============= ======================================== + [r|w]bps The maximum sequential IO throughput + [r|w]seqiops The maximum 4k sequential IOs per second + [r|w]randiops The maximum 4k random IOs per second + ============= ======================================== + + From the above, the builtin linear model determines the base + costs of a sequential and random IO and the cost coefficient + for the IO size. While simple, this model can cover most + common device classes acceptably. + + The IO cost model isn't expected to be accurate in absolute + sense and is scaled to the device behavior dynamically. + + If needed, tools/cgroup/iocost_coef_gen.py can be used to + generate device-specific coefficients. + io.weight A read-write flat-keyed file which exists on non-root cgroups. The default is "default 100". |