diff options
Diffstat (limited to 'Documentation/admin-guide/perf')
| -rw-r--r-- | Documentation/admin-guide/perf/alibaba_pmu.rst | 100 | ||||
| -rw-r--r-- | Documentation/admin-guide/perf/arm-ccn.rst | 2 | ||||
| -rw-r--r-- | Documentation/admin-guide/perf/arm-cmn.rst | 65 | ||||
| -rw-r--r-- | Documentation/admin-guide/perf/hisi-pcie-pmu.rst | 106 | ||||
| -rw-r--r-- | Documentation/admin-guide/perf/hisi-pmu.rst | 54 | ||||
| -rw-r--r-- | Documentation/admin-guide/perf/hns3-pmu.rst | 136 | ||||
| -rw-r--r-- | Documentation/admin-guide/perf/imx-ddr.rst | 5 | ||||
| -rw-r--r-- | Documentation/admin-guide/perf/index.rst | 4 |
8 files changed, 469 insertions, 3 deletions
diff --git a/Documentation/admin-guide/perf/alibaba_pmu.rst b/Documentation/admin-guide/perf/alibaba_pmu.rst new file mode 100644 index 000000000000..11de998bb480 --- /dev/null +++ b/Documentation/admin-guide/perf/alibaba_pmu.rst @@ -0,0 +1,100 @@ +============================================================= +Alibaba's T-Head SoC Uncore Performance Monitoring Unit (PMU) +============================================================= + +The Yitian 710, custom-built by Alibaba Group's chip development business, +T-Head, implements uncore PMU for performance and functional debugging to +facilitate system maintenance. + +DDR Sub-System Driveway (DRW) PMU Driver +========================================= + +Yitian 710 employs eight DDR5/4 channels, four on each die. Each DDR5 channel +is independent of others to service system memory requests. And one DDR5 +channel is split into two independent sub-channels. The DDR Sub-System Driveway +implements separate PMUs for each sub-channel to monitor various performance +metrics. + +The Driveway PMU devices are named as ali_drw_<sys_base_addr> with perf. +For example, ali_drw_21000 and ali_drw_21080 are two PMU devices for two +sub-channels of the same channel in die 0. And the PMU device of die 1 is +prefixed with ali_drw_400XXXXX, e.g. ali_drw_40021000. + +Each sub-channel has 36 PMU counters in total, which is classified into +four groups: + +- Group 0: PMU Cycle Counter. This group has one pair of counters + pmu_cycle_cnt_low and pmu_cycle_cnt_high, that is used as the cycle count + based on DDRC core clock. + +- Group 1: PMU Bandwidth Counters. This group has 8 counters that are used + to count the total access number of either the eight bank groups in a + selected rank, or four ranks separately in the first 4 counters. The base + transfer unit is 64B. + +- Group 2: PMU Retry Counters. This group has 10 counters, that intend to + count the total retry number of each type of uncorrectable error. + +- Group 3: PMU Common Counters. This group has 16 counters, that are used + to count the common events. + +For now, the Driveway PMU driver only uses counters in group 0 and group 3. + +The DDR Controller (DDRCTL) and DDR PHY combine to create a complete solution +for connecting an SoC application bus to DDR memory devices. The DDRCTL +receives transactions Host Interface (HIF) which is custom-defined by Synopsys. +These transactions are queued internally and scheduled for access while +satisfying the SDRAM protocol timing requirements, transaction priorities, and +dependencies between the transactions. The DDRCTL in turn issues commands on +the DDR PHY Interface (DFI) to the PHY module, which launches and captures data +to and from the SDRAM. The driveway PMUs have hardware logic to gather +statistics and performance logging signals on HIF, DFI, etc. + +By counting the READ, WRITE and RMW commands sent to the DDRC through the HIF +interface, we could calculate the bandwidth. Example usage of counting memory +data bandwidth:: + + perf stat \ + -e ali_drw_21000/hif_wr/ \ + -e ali_drw_21000/hif_rd/ \ + -e ali_drw_21000/hif_rmw/ \ + -e ali_drw_21000/cycle/ \ + -e ali_drw_21080/hif_wr/ \ + -e ali_drw_21080/hif_rd/ \ + -e ali_drw_21080/hif_rmw/ \ + -e ali_drw_21080/cycle/ \ + -e ali_drw_23000/hif_wr/ \ + -e ali_drw_23000/hif_rd/ \ + -e ali_drw_23000/hif_rmw/ \ + -e ali_drw_23000/cycle/ \ + -e ali_drw_23080/hif_wr/ \ + -e ali_drw_23080/hif_rd/ \ + -e ali_drw_23080/hif_rmw/ \ + -e ali_drw_23080/cycle/ \ + -e ali_drw_25000/hif_wr/ \ + -e ali_drw_25000/hif_rd/ \ + -e ali_drw_25000/hif_rmw/ \ + -e ali_drw_25000/cycle/ \ + -e ali_drw_25080/hif_wr/ \ + -e ali_drw_25080/hif_rd/ \ + -e ali_drw_25080/hif_rmw/ \ + -e ali_drw_25080/cycle/ \ + -e ali_drw_27000/hif_wr/ \ + -e ali_drw_27000/hif_rd/ \ + -e ali_drw_27000/hif_rmw/ \ + -e ali_drw_27000/cycle/ \ + -e ali_drw_27080/hif_wr/ \ + -e ali_drw_27080/hif_rd/ \ + -e ali_drw_27080/hif_rmw/ \ + -e ali_drw_27080/cycle/ -- sleep 10 + +The average DRAM bandwidth can be calculated as follows: + +- Read Bandwidth = perf_hif_rd * DDRC_WIDTH * DDRC_Freq / DDRC_Cycle +- Write Bandwidth = (perf_hif_wr + perf_hif_rmw) * DDRC_WIDTH * DDRC_Freq / DDRC_Cycle + +Here, DDRC_WIDTH = 64 bytes. + +The current driver does not support sampling. So "perf record" is +unsupported. Also attach to a task is unsupported as the events are all +uncore. diff --git a/Documentation/admin-guide/perf/arm-ccn.rst b/Documentation/admin-guide/perf/arm-ccn.rst index 832b0c64023a..f62f7fe50eba 100644 --- a/Documentation/admin-guide/perf/arm-ccn.rst +++ b/Documentation/admin-guide/perf/arm-ccn.rst @@ -27,7 +27,7 @@ Crosspoint PMU events require "xp" (index), "bus" (bus number) and "vc" (virtual channel ID). Crosspoint watchpoint-based events (special "event" value 0xfe) -require "xp" and "vc" as as above plus "port" (device port index), +require "xp" and "vc" as above plus "port" (device port index), "dir" (transmit/receive direction), comparator values ("cmp_l" and "cmp_h") and "mask", being index of the comparator mask. diff --git a/Documentation/admin-guide/perf/arm-cmn.rst b/Documentation/admin-guide/perf/arm-cmn.rst new file mode 100644 index 000000000000..796e25b7027b --- /dev/null +++ b/Documentation/admin-guide/perf/arm-cmn.rst @@ -0,0 +1,65 @@ +============================= +Arm Coherent Mesh Network PMU +============================= + +CMN-600 is a configurable mesh interconnect consisting of a rectangular +grid of crosspoints (XPs), with each crosspoint supporting up to two +device ports to which various AMBA CHI agents are attached. + +CMN implements a distributed PMU design as part of its debug and trace +functionality. This consists of a local monitor (DTM) at every XP, which +counts up to 4 event signals from the connected device nodes and/or the +XP itself. Overflow from these local counters is accumulated in up to 8 +global counters implemented by the main controller (DTC), which provides +overall PMU control and interrupts for global counter overflow. + +PMU events +---------- + +The PMU driver registers a single PMU device for the whole interconnect, +see /sys/bus/event_source/devices/arm_cmn_0. Multi-chip systems may link +more than one CMN together via external CCIX links - in this situation, +each mesh counts its own events entirely independently, and additional +PMU devices will be named arm_cmn_{1..n}. + +Most events are specified in a format based directly on the TRM +definitions - "type" selects the respective node type, and "eventid" the +event number. Some events require an additional occupancy ID, which is +specified by "occupid". + +* Since RN-D nodes do not have any distinct events from RN-I nodes, they + are treated as the same type (0xa), and the common event templates are + named "rnid_*". + +* The cycle counter is treated as a synthetic event belonging to the DTC + node ("type" == 0x3, "eventid" is ignored). + +* XP events also encode the port and channel in the "eventid" field, to + match the underlying pmu_event0_id encoding for the pmu_event_sel + register. The event templates are named with prefixes to cover all + permutations. + +By default each event provides an aggregate count over all nodes of the +given type. To target a specific node, "bynodeid" must be set to 1 and +"nodeid" to the appropriate value derived from the CMN configuration +(as defined in the "Node ID Mapping" section of the TRM). + +Watchpoints +----------- + +The PMU can also count watchpoint events to monitor specific flit +traffic. Watchpoints are treated as a synthetic event type, and like PMU +events can be global or targeted with a particular XP's "nodeid" value. +Since the watchpoint direction is otherwise implicit in the underlying +register selection, separate events are provided for flit uploads and +downloads. + +The flit match value and mask are passed in config1 and config2 ("val" +and "mask" respectively). "wp_dev_sel", "wp_chn_sel", "wp_grp" and +"wp_exclusive" are specified per the TRM definitions for dtm_wp_config0. +Where a watchpoint needs to match fields from both match groups on the +REQ or SNP channel, it can be specified as two events - one for each +group - with the same nonzero "combine" value. The count for such a +pair of combined events will be attributed to the primary match. +Watchpoint events with a "combine" value of 0 are considered independent +and will count individually. diff --git a/Documentation/admin-guide/perf/hisi-pcie-pmu.rst b/Documentation/admin-guide/perf/hisi-pcie-pmu.rst new file mode 100644 index 000000000000..294ebbdb22af --- /dev/null +++ b/Documentation/admin-guide/perf/hisi-pcie-pmu.rst @@ -0,0 +1,106 @@ +================================================ +HiSilicon PCIe Performance Monitoring Unit (PMU) +================================================ + +On Hip09, HiSilicon PCIe Performance Monitoring Unit (PMU) could monitor +bandwidth, latency, bus utilization and buffer occupancy data of PCIe. + +Each PCIe Core has a PMU to monitor multi Root Ports of this PCIe Core and +all Endpoints downstream these Root Ports. + + +HiSilicon PCIe PMU driver +========================= + +The PCIe PMU driver registers a perf PMU with the name of its sicl-id and PCIe +Core id.:: + + /sys/bus/event_source/hisi_pcie<sicl>_<core> + +PMU driver provides description of available events and filter options in sysfs, +see /sys/bus/event_source/devices/hisi_pcie<sicl>_<core>. + +The "format" directory describes all formats of the config (events) and config1 +(filter options) fields of the perf_event_attr structure. The "events" directory +describes all documented events shown in perf list. + +The "identifier" sysfs file allows users to identify the version of the +PMU hardware device. + +The "bus" sysfs file allows users to get the bus number of Root Ports +monitored by PMU. + +Example usage of perf:: + + $# perf list + hisi_pcie0_0/rx_mwr_latency/ [kernel PMU event] + hisi_pcie0_0/rx_mwr_cnt/ [kernel PMU event] + ------------------------------------------ + + $# perf stat -e hisi_pcie0_0/rx_mwr_latency/ + $# perf stat -e hisi_pcie0_0/rx_mwr_cnt/ + $# perf stat -g -e hisi_pcie0_0/rx_mwr_latency/ -e hisi_pcie0_0/rx_mwr_cnt/ + +The current driver does not support sampling. So "perf record" is unsupported. +Also attach to a task is unsupported for PCIe PMU. + +Filter options +-------------- + +1. Target filter +PMU could only monitor the performance of traffic downstream target Root Ports +or downstream target Endpoint. PCIe PMU driver support "port" and "bdf" +interfaces for users, and these two interfaces aren't supported at the same +time. + +-port +"port" filter can be used in all PCIe PMU events, target Root Port can be +selected by configuring the 16-bits-bitmap "port". Multi ports can be selected +for AP-layer-events, and only one port can be selected for TL/DL-layer-events. + +For example, if target Root Port is 0000:00:00.0 (x8 lanes), bit0 of bitmap +should be set, port=0x1; if target Root Port is 0000:00:04.0 (x4 lanes), +bit8 is set, port=0x100; if these two Root Ports are both monitored, port=0x101. + +Example usage of perf:: + + $# perf stat -e hisi_pcie0_0/rx_mwr_latency,port=0x1/ sleep 5 + +-bdf + +"bdf" filter can only be used in bandwidth events, target Endpoint is selected +by configuring BDF to "bdf". Counter only counts the bandwidth of message +requested by target Endpoint. + +For example, "bdf=0x3900" means BDF of target Endpoint is 0000:39:00.0. + +Example usage of perf:: + + $# perf stat -e hisi_pcie0_0/rx_mrd_flux,bdf=0x3900/ sleep 5 + +2. Trigger filter +Event statistics start when the first time TLP length is greater/smaller +than trigger condition. You can set the trigger condition by writing "trig_len", +and set the trigger mode by writing "trig_mode". This filter can only be used +in bandwidth events. + +For example, "trig_len=4" means trigger condition is 2^4 DW, "trig_mode=0" +means statistics start when TLP length > trigger condition, "trig_mode=1" +means start when TLP length < condition. + +Example usage of perf:: + + $# perf stat -e hisi_pcie0_0/rx_mrd_flux,trig_len=0x4,trig_mode=1/ sleep 5 + +3. Threshold filter +Counter counts when TLP length within the specified range. You can set the +threshold by writing "thr_len", and set the threshold mode by writing +"thr_mode". This filter can only be used in bandwidth events. + +For example, "thr_len=4" means threshold is 2^4 DW, "thr_mode=0" means +counter counts when TLP length >= threshold, and "thr_mode=1" means counts +when TLP length < threshold. + +Example usage of perf:: + + $# perf stat -e hisi_pcie0_0/rx_mrd_flux,thr_len=0x4,thr_mode=1/ sleep 5 diff --git a/Documentation/admin-guide/perf/hisi-pmu.rst b/Documentation/admin-guide/perf/hisi-pmu.rst index 404a5c3d9d00..546979360513 100644 --- a/Documentation/admin-guide/perf/hisi-pmu.rst +++ b/Documentation/admin-guide/perf/hisi-pmu.rst @@ -53,6 +53,60 @@ Example usage of perf:: $# perf stat -a -e hisi_sccl3_l3c0/rd_hit_cpipe/ sleep 5 $# perf stat -a -e hisi_sccl3_l3c0/config=0x02/ sleep 5 +For HiSilicon uncore PMU v2 whose identifier is 0x30, the topology is the same +as PMU v1, but some new functions are added to the hardware. + +(a) L3C PMU supports filtering by core/thread within the cluster which can be +specified as a bitmap:: + + $# perf stat -a -e hisi_sccl3_l3c0/config=0x02,tt_core=0x3/ sleep 5 + +This will only count the operations from core/thread 0 and 1 in this cluster. + +(b) Tracetag allow the user to chose to count only read, write or atomic +operations via the tt_req parameeter in perf. The default value counts all +operations. tt_req is 3bits, 3'b100 represents read operations, 3'b101 +represents write operations, 3'b110 represents atomic store operations and +3'b111 represents atomic non-store operations, other values are reserved:: + + $# perf stat -a -e hisi_sccl3_l3c0/config=0x02,tt_req=0x4/ sleep 5 + +This will only count the read operations in this cluster. + +(c) Datasrc allows the user to check where the data comes from. It is 5 bits. +Some important codes are as follows: +5'b00001: comes from L3C in this die; +5'b01000: comes from L3C in the cross-die; +5'b01001: comes from L3C which is in another socket; +5'b01110: comes from the local DDR; +5'b01111: comes from the cross-die DDR; +5'b10000: comes from cross-socket DDR; +etc, it is mainly helpful to find that the data source is nearest from the CPU +cores. If datasrc_cfg is used in the multi-chips, the datasrc_skt shall be +configured in perf command:: + + $# perf stat -a -e hisi_sccl3_l3c0/config=0xb9,datasrc_cfg=0xE/, + hisi_sccl3_l3c0/config=0xb9,datasrc_cfg=0xF/ sleep 5 + +(d)Some HiSilicon SoCs encapsulate multiple CPU and IO dies. Each CPU die +contains several Compute Clusters (CCLs). The I/O dies are called Super I/O +clusters (SICL) containing multiple I/O clusters (ICLs). Each CCL/ICL in the +SoC has a unique ID. Each ID is 11bits, include a 6-bit SCCL-ID and 5-bit +CCL/ICL-ID. For I/O die, the ICL-ID is followed by: +5'b00000: I/O_MGMT_ICL; +5'b00001: Network_ICL; +5'b00011: HAC_ICL; +5'b10000: PCIe_ICL; + +Users could configure IDs to count data come from specific CCL/ICL, by setting +srcid_cmd & srcid_msk, and data desitined for specific CCL/ICL by setting +tgtid_cmd & tgtid_msk. A set bit in srcid_msk/tgtid_msk means the PMU will not +check the bit when matching against the srcid_cmd/tgtid_cmd. + +If all of these options are disabled, it can works by the default value that +doesn't distinguish the filter condition and ID information and will return +the total counter values in the PMU counters. + The current driver does not support sampling. So "perf record" is unsupported. Also attach to a task is unsupported as the events are all uncore. diff --git a/Documentation/admin-guide/perf/hns3-pmu.rst b/Documentation/admin-guide/perf/hns3-pmu.rst new file mode 100644 index 000000000000..578407e487d6 --- /dev/null +++ b/Documentation/admin-guide/perf/hns3-pmu.rst @@ -0,0 +1,136 @@ +====================================== +HNS3 Performance Monitoring Unit (PMU) +====================================== + +HNS3(HiSilicon network system 3) Performance Monitoring Unit (PMU) is an +End Point device to collect performance statistics of HiSilicon SoC NIC. +On Hip09, each SICL(Super I/O cluster) has one PMU device. + +HNS3 PMU supports collection of performance statistics such as bandwidth, +latency, packet rate and interrupt rate. + +Each HNS3 PMU supports 8 hardware events. + +HNS3 PMU driver +=============== + +The HNS3 PMU driver registers a perf PMU with the name of its sicl id.:: + + /sys/devices/hns3_pmu_sicl_<sicl_id> + +PMU driver provides description of available events, filter modes, format, +identifier and cpumask in sysfs. + +The "events" directory describes the event code of all supported events +shown in perf list. + +The "filtermode" directory describes the supported filter modes of each +event. + +The "format" directory describes all formats of the config (events) and +config1 (filter options) fields of the perf_event_attr structure. + +The "identifier" file shows version of PMU hardware device. + +The "bdf_min" and "bdf_max" files show the supported bdf range of each +pmu device. + +The "hw_clk_freq" file shows the hardware clock frequency of each pmu +device. + +Example usage of checking event code and subevent code:: + + $# cat /sys/devices/hns3_pmu_sicl_0/events/dly_tx_normal_to_mac_time + config=0x00204 + $# cat /sys/devices/hns3_pmu_sicl_0/events/dly_tx_normal_to_mac_packet_num + config=0x10204 + +Each performance statistic has a pair of events to get two values to +calculate real performance data in userspace. + +The bits 0~15 of config (here 0x0204) are the true hardware event code. If +two events have same value of bits 0~15 of config, that means they are +event pair. And the bit 16 of config indicates getting counter 0 or +counter 1 of hardware event. + +After getting two values of event pair in usersapce, the formula of +computation to calculate real performance data is::: + + counter 0 / counter 1 + +Example usage of checking supported filter mode:: + + $# cat /sys/devices/hns3_pmu_sicl_0/filtermode/bw_ssu_rpu_byte_num + filter mode supported: global/port/port-tc/func/func-queue/ + +Example usage of perf:: + + $# perf list + hns3_pmu_sicl_0/bw_ssu_rpu_byte_num/ [kernel PMU event] + hns3_pmu_sicl_0/bw_ssu_rpu_time/ [kernel PMU event] + ------------------------------------------ + + $# perf stat -g -e hns3_pmu_sicl_0/bw_ssu_rpu_byte_num,global=1/ -e hns3_pmu_sicl_0/bw_ssu_rpu_time,global=1/ -I 1000 + or + $# perf stat -g -e hns3_pmu_sicl_0/config=0x00002,global=1/ -e hns3_pmu_sicl_0/config=0x10002,global=1/ -I 1000 + + +Filter modes +-------------- + +1. global mode +PMU collect performance statistics for all HNS3 PCIe functions of IO DIE. +Set the "global" filter option to 1 will enable this mode. +Example usage of perf:: + + $# perf stat -a -e hns3_pmu_sicl_0/config=0x1020F,global=1/ -I 1000 + +2. port mode +PMU collect performance statistic of one whole physical port. The port id +is same as mac id. The "tc" filter option must be set to 0xF in this mode, +here tc stands for traffic class. + +Example usage of perf:: + + $# perf stat -a -e hns3_pmu_sicl_0/config=0x1020F,port=0,tc=0xF/ -I 1000 + +3. port-tc mode +PMU collect performance statistic of one tc of physical port. The port id +is same as mac id. The "tc" filter option must be set to 0 ~ 7 in this +mode. +Example usage of perf:: + + $# perf stat -a -e hns3_pmu_sicl_0/config=0x1020F,port=0,tc=0/ -I 1000 + +4. func mode +PMU collect performance statistic of one PF/VF. The function id is BDF of +PF/VF, its conversion formula:: + + func = (bus << 8) + (device << 3) + (function) + +for example: + BDF func + 35:00.0 0x3500 + 35:00.1 0x3501 + 35:01.0 0x3508 + +In this mode, the "queue" filter option must be set to 0xFFFF. +Example usage of perf:: + + $# perf stat -a -e hns3_pmu_sicl_0/config=0x1020F,bdf=0x3500,queue=0xFFFF/ -I 1000 + +5. func-queue mode +PMU collect performance statistic of one queue of PF/VF. The function id +is BDF of PF/VF, the "queue" filter option must be set to the exact queue +id of function. +Example usage of perf:: + + $# perf stat -a -e hns3_pmu_sicl_0/config=0x1020F,bdf=0x3500,queue=0/ -I 1000 + +6. func-intr mode +PMU collect performance statistic of one interrupt of PF/VF. The function +id is BDF of PF/VF, the "intr" filter option must be set to the exact +interrupt id of function. +Example usage of perf:: + + $# perf stat -a -e hns3_pmu_sicl_0/config=0x00301,bdf=0x3500,intr=0/ -I 1000 diff --git a/Documentation/admin-guide/perf/imx-ddr.rst b/Documentation/admin-guide/perf/imx-ddr.rst index 3726a10a03ba..90926d0fb8ec 100644 --- a/Documentation/admin-guide/perf/imx-ddr.rst +++ b/Documentation/admin-guide/perf/imx-ddr.rst @@ -4,7 +4,7 @@ Freescale i.MX8 DDR Performance Monitoring Unit (PMU) There are no performance counters inside the DRAM controller, so performance signals are brought out to the edge of the controller where a set of 4 x 32 bit -counters is implemented. This is controlled by the CSV modes programed in counter +counters is implemented. This is controlled by the CSV modes programmed in counter control register which causes a large number of PERF signals to be generated. Selection of the value for each counter is done via the config registers. There @@ -43,7 +43,8 @@ value 1 for supported. AXI_ID and AXI_MASKING are mapped on DPCR1 register in performance counter. When non-masked bits are matching corresponding AXI_ID bits then counter is - incremented. Perf counter is incremented if + incremented. Perf counter is incremented if:: + AxID && AXI_MASKING == AXI_ID && AXI_MASKING This filter doesn't support filter different AXI ID for axid-read and axid-write diff --git a/Documentation/admin-guide/perf/index.rst b/Documentation/admin-guide/perf/index.rst index 47c99f40cc16..793e1970bc05 100644 --- a/Documentation/admin-guide/perf/index.rst +++ b/Documentation/admin-guide/perf/index.rst @@ -8,10 +8,14 @@ Performance monitor support :maxdepth: 1 hisi-pmu + hisi-pcie-pmu + hns3-pmu imx-ddr qcom_l2_pmu qcom_l3_pmu arm-ccn + arm-cmn xgene-pmu arm_dsu_pmu thunderx2-pmu + alibaba_pmu |