diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media/video-interfaces.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/media/video-interfaces.txt | 34 |
1 files changed, 28 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt index 852041a7480c..258b8dfddf48 100644 --- a/Documentation/devicetree/bindings/media/video-interfaces.txt +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -55,6 +55,15 @@ divided into two separate ITU-R BT.656 8-bit busses. In such case bus-width and data-shift properties can be used to assign physical data lines to each endpoint node (logical bus). +Documenting bindings for devices +-------------------------------- + +All required and optional bindings the device supports shall be explicitly +documented in device DT binding documentation. This also includes port and +endpoint nodes for the device, including unit-addresses and reg properties where +relevant. + +Please also see Documentation/devicetree/bindings/graph.txt . Required properties ------------------- @@ -67,6 +76,16 @@ are required in a relevant parent node: identifier, should be 1. - #size-cells : should be zero. + +Optional properties +------------------- + +- flash-leds: An array of phandles, each referring to a flash LED, a sub-node + of the LED driver device node. + +- lens-focus: A phandle to the node of the focus lens controller. + + Optional endpoint properties ---------------------------- @@ -99,7 +118,10 @@ Optional endpoint properties determines the logical lane number, while the value of an entry indicates physical lane, e.g. for 2-lane MIPI CSI-2 bus we could have "data-lanes = <1 2>;", assuming the clock lane is on hardware lane 0. - This property is valid for serial busses only (e.g. MIPI CSI-2). + If the hardware does not support lane reordering, monotonically + incremented values shall be used from 0 or 1 onwards, depending on + whether or not there is also a clock lane. This property is valid for + serial busses only (e.g. MIPI CSI-2). - clock-lanes: an array of physical clock lane indexes. Position of an entry determines the logical lane number, while the value of an entry indicates physical lane, e.g. for a MIPI CSI-2 bus we could have "clock-lanes = <0>;", @@ -132,7 +154,7 @@ imx074 is linked to ceu0 through the MIPI CSI-2 receiver (csi2). ceu0 has a 'port' node which may indicate that at any time only one of the following data pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0. - ceu0: ceu@0xfe910000 { + ceu0: ceu@fe910000 { compatible = "renesas,sh-mobile-ceu"; reg = <0xfe910000 0xa0>; interrupts = <0x880>; @@ -171,9 +193,9 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0. }; }; - i2c0: i2c@0xfff20000 { + i2c0: i2c@fff20000 { ... - ov772x_1: camera@0x21 { + ov772x_1: camera@21 { compatible = "ovti,ov772x"; reg = <0x21>; vddio-supply = <®ulator1>; @@ -197,7 +219,7 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0. }; }; - imx074: camera@0x1a { + imx074: camera@1a { compatible = "sony,imx074"; reg = <0x1a>; vddio-supply = <®ulator1>; @@ -217,7 +239,7 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0. }; }; - csi2: csi2@0xffc90000 { + csi2: csi2@ffc90000 { compatible = "renesas,sh-mobile-csi2"; reg = <0xffc90000 0x1000>; interrupts = <0x17a0>; |