diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd')
7 files changed, 224 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt index 34dd89087cff..86446074e206 100644 --- a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt +++ b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt @@ -135,6 +135,8 @@ Required properties: - clocks: contains a phandle to the syscon node describing the clocks. There should then be one cell representing the clock to use +Optional properties: + - memory-region: A phandle to a reserved_memory region to be used for the LPC to AHB mapping diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index 188f0373d441..2af4ff95d6bc 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -32,6 +32,15 @@ Required properties: - interrupt-controller: The PMIC has its own internal IRQs - #interrupt-cells: Should be set to 1 +Supported common regulator properties, see ../regulator/regulator.txt for +more information: +- regulator-ramp-delay: sets the ramp up delay in uV/us + AXP20x/DCDC2: 1600, 800 + AXP20x/LDO3: 1600, 800 +- regulator-soft-start: enable the output at the lowest possible voltage and + only then set the desired voltage + AXP20x/LDO3: software-based implementation + Optional properties: - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz AXP152/20X: range: 750-1875, Default: 1.5 MHz diff --git a/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt new file mode 100644 index 000000000000..004b0158cf4d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt @@ -0,0 +1,68 @@ +Cirrus Logic Lochnagar Audio Development Board + +Lochnagar is an evaluation and development board for Cirrus Logic +Smart CODEC and Amp devices. It allows the connection of most Cirrus +Logic devices on mini-cards, as well as allowing connection of +various application processor systems to provide a full evaluation +platform. Audio system topology, clocking and power can all be +controlled through the Lochnagar, allowing the device under test +to be used in a variety of possible use cases. + +Also see these documents for generic binding information: + [1] GPIO : ../gpio/gpio.txt + +And these for relevant defines: + [2] include/dt-bindings/pinctrl/lochnagar.h + [3] include/dt-bindings/clock/lochnagar.h + +And these documents for the required sub-node binding details: + [4] Clock: ../clock/cirrus,lochnagar.txt + [5] Pinctrl: ../pinctrl/cirrus,lochnagar.txt + [6] Regulator: ../regulator/cirrus,lochnagar.txt + +Required properties: + + - compatible : One of the following strings: + "cirrus,lochnagar1" + "cirrus,lochnagar2" + + - reg : I2C slave address + + - reset-gpios : Reset line to the Lochnagar, see [1]. + +Required sub-nodes: + + - lochnagar-clk : Binding for the clocking components, see [4]. + + - lochnagar-pinctrl : Binding for the pin control components, see [5]. + +Optional sub-nodes: + + - Bindings for the regulator components, see [6]. Only available on + Lochnagar 2. + +Optional properties: + + - present-gpios : Host present line, indicating the presence of a + host system, see [1]. This can be omitted if the present line is + tied in hardware. + +Example: + +lochnagar: lochnagar@22 { + compatible = "cirrus,lochnagar2"; + reg = <0x22>; + + reset-gpios = <&gpio0 55 0>; + present-gpios = <&gpio0 60 0>; + + lochnagar-clk { + compatible = "cirrus,lochnagar2-clk"; + ... + }; + + lochnagar-pinctrl { + compatible = "cirrus,lochnagar-pinctrl"; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77650.txt b/Documentation/devicetree/bindings/mfd/max77650.txt new file mode 100644 index 000000000000..b529d8d19335 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77650.txt @@ -0,0 +1,46 @@ +MAX77650 ultra low-power PMIC from Maxim Integrated. + +Required properties: +------------------- +- compatible: Must be "maxim,max77650" +- reg: I2C device address. +- interrupts: The interrupt on the parent the controller is + connected to. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Must be <2>. + +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Must be <2>. The first cell is the pin number and + the second cell is used to specify the gpio active + state. + +Optional properties: +-------------------- +gpio-line-names: Single string containing the name of the GPIO line. + +The GPIO-controller module is represented as part of the top-level PMIC +node. The device exposes a single GPIO line. + +For device-tree bindings of other sub-modules (regulator, power supply, +LEDs and onkey) refer to the binding documents under the respective +sub-system directories. + +For more details on GPIO bindings, please refer to the generic GPIO DT +binding document <devicetree/bindings/gpio/gpio.txt>. + +Example: +-------- + + pmic@48 { + compatible = "maxim,max77650"; + reg = <0x48>; + + interrupt-controller; + interrupt-parent = <&gpio2>; + #interrupt-cells = <2>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "max77650-charger"; + }; diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt index a4b056761eaa..d5f68ac78d15 100644 --- a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt @@ -23,6 +23,20 @@ Required properties: Optional properties: - clock-output-names : Should contain name for output clock. +- rohm,reset-snvs-powered : Transfer BD718x7 to SNVS state at reset. + +The BD718x7 supports two different HW states as reset target states. States +are called as SNVS and READY. At READY state all the PMIC power outputs go +down and OTP is reload. At the SNVS state all other logic and external +devices apart from the SNVS power domain are shut off. Please refer to NXP +i.MX8 documentation for further information regarding SNVS state. When a +reset is done via SNVS state the PMIC OTP data is not reload. This causes +power outputs that have been under SW control to stay down when reset has +switched power state to SNVS. If reset is done via READY state the power +outputs will be returned to HW control by OTP loading. Thus the reset +target state is set to READY by default. If SNVS state is used the boot +crucial regulators must have the regulator-always-on and regulator-boot-on +properties set in regulator node. Example: @@ -43,6 +57,7 @@ Example: #clock-cells = <0>; clocks = <&osc 0>; clock-output-names = "bd71837-32k-out"; + rohm,reset-snvs-powered; regulators { buck1: BUCK1 { @@ -50,8 +65,10 @@ Example: regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + regulator-always-on; regulator-ramp-delay = <1250>; }; + // [...] }; }; diff --git a/Documentation/devicetree/bindings/mfd/st,stpmic1.txt b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt new file mode 100644 index 000000000000..afd45c089585 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt @@ -0,0 +1,61 @@ +* STMicroelectronics STPMIC1 Power Management IC + +Required properties: +- compatible: : "st,stpmic1" +- reg: : The I2C slave address for the STPMIC1 chip. +- interrupts: : The interrupt line the device is connected to. +- #interrupt-cells: : Should be 1. +- interrupt-controller: : Marks the device node as an interrupt controller. + Interrupt numbers are defined at + dt-bindings/mfd/st,stpmic1.h. + +STPMIC1 consists in a varied group of sub-devices. +Each sub-device binding is be described in own documentation file. + +Device Description +------ ------------ +st,stpmic1-onkey : Power on key, see ../input/st,stpmic1-onkey.txt +st,stpmic1-regulators : Regulators, see ../regulator/st,stpmic1-regulator.txt +st,stpmic1-wdt : Watchdog, see ../watchdog/st,stpmic1-wdt.txt + +Example: + +#include <dt-bindings/mfd/st,stpmic1.h> + +pmic: pmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupt-parent = <&gpioa>; + interrupts = <0 2>; + + interrupt-controller; + #interrupt-cells = <2>; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + }; + + regulators { + compatible = "st,stpmic1-regulators"; + + vdd_core: buck1 { + regulator-name = "vdd_core"; + regulator-boot-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1200000>; + }; + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-pull-down; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt index c797c05cd3c2..d4408a417193 100644 --- a/Documentation/devicetree/bindings/mfd/stmpe.txt +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -4,15 +4,29 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio, keypad, touchscreen, adc, pwm, rotator. Required properties: - - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" - - reg : I2C/SPI address of the device + - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" + - reg : I2C/SPI address of the device Optional properties: - - interrupts : The interrupt outputs from the controller - - interrupt-controller : Marks the device node as an interrupt controller - - wakeup-source : Marks the input device as wakable - - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 - - irq-gpio : If present, which GPIO to use for event IRQ + - interrupts : The interrupt outputs from the controller + - interrupt-controller : Marks the device node as an interrupt controller + - wakeup-source : Marks the input device as wakable + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + - irq-gpio : If present, which GPIO to use for event IRQ + +Optional properties for devices with touch and ADC (STMPE811|STMPE610): + - st,sample-time : ADC conversion time in number of clock. + 0 -> 36 clocks 4 -> 80 clocks (recommended) + 1 -> 44 clocks 5 -> 96 clocks + 2 -> 56 clocks 6 -> 124 clocks + 3 -> 64 clocks + - st,mod-12b : ADC Bit mode + 0 -> 10bit ADC 1 -> 12bit ADC + - st,ref-sel : ADC reference source + 0 -> internal 1 -> external + - st,adc-freq : ADC Clock speed + 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz + 1 -> 3.25 MHz Example: |