diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mtd')
10 files changed, 164 insertions, 23 deletions
diff --git a/Documentation/devicetree/bindings/mtd/arm-versatile.txt b/Documentation/devicetree/bindings/mtd/arm-versatile.txt index 476845db94d0..beace4b89daa 100644 --- a/Documentation/devicetree/bindings/mtd/arm-versatile.txt +++ b/Documentation/devicetree/bindings/mtd/arm-versatile.txt @@ -4,5 +4,5 @@ Required properties: - compatible : must be "arm,versatile-flash"; - bank-width : width in bytes of flash interface. -Optional properties: -- Subnode partition map from mtd flash binding +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. diff --git a/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt index ef66ddd01da0..1889a4db5b7c 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt @@ -3,6 +3,9 @@ Required properties: - compatible : "atmel,<model>", "atmel,<series>", "atmel,dataflash". +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + Example: flash@1 { diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt new file mode 100644 index 000000000000..5903ecf6e895 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -0,0 +1,41 @@ +Atmel NAND flash + +Required properties: +- compatible : "atmel,at91rm9200-nand". +- reg : should specify localbus address and size used for the chip, + and if availlable the ECC. +- atmel,nand-addr-offset : offset for the address latch. +- atmel,nand-cmd-offset : offset for the command latch. +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. + +- gpios : specifies the gpio pins to control the NAND device. detect is an + optional gpio and may be set to 0 if not present. + +Optional properties: +- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. + Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", + "soft_bch". +- nand-bus-width : 8 or 16 bus width if not present 8 +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false + +Examples: +nand0: nand@40000000,0 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + 0xffffe800 0x200 + >; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + nand-on-flash-bbt; + nand-ecc-mode = "soft"; + gpios = <&pioC 13 0 + &pioC 14 0 + 0 + >; + partition@0 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt index 00f1f546b32e..fce4894f5a98 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt @@ -19,6 +19,10 @@ Optional properties: read registers (tR). Required if property "gpios" is not used (R/B# pins not connected). +Each flash chip described may optionally contain additional sub-nodes +describing partitions of the address space. See partition.txt for more +detail. + Examples: upm@1,0 { diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt new file mode 100644 index 000000000000..e2c663b354d2 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -0,0 +1,33 @@ +* FSMC NAND + +Required properties: +- compatible : "st,spear600-fsmc-nand" +- reg : Address range of the mtd chip +- reg-names: Should contain the reg names "fsmc_regs" and "nand_data" +- st,ale-off : Chip specific offset to ALE +- st,cle-off : Chip specific offset to CLE + +Optional properties: +- bank-width : Width (in bytes) of the device. If not present, the width + defaults to 1 byte +- nand-skip-bbtscan: Indicates the the BBT scanning should be skipped + +Example: + + fsmc: flash@d1800000 { + compatible = "st,spear600-fsmc-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xd1800000 0x1000 /* FSMC Register */ + 0xd2000000 0x4000>; /* NAND Base */ + reg-names = "fsmc_regs", "nand_data"; + st,ale-off = <0x20000>; + st,cle-off = <0x10000>; + + bank-width = <1>; + nand-skip-bbtscan; + + partition@0 { + ... + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt index 719f4dc58df7..36ef07d3c90f 100644 --- a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt @@ -25,6 +25,9 @@ Optional properties: GPIO state and before and after command byte writes, this register will be read to ensure that the GPIO accesses have completed. +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + Examples: gpio-nand@1,0 { diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index 80152cb567d9..a63c2bd7de2b 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -23,27 +23,8 @@ are defined: - vendor-id : Contains the flash chip's vendor id (1 byte). - device-id : Contains the flash chip's device id (1 byte). -In addition to the information on the mtd bank itself, the -device tree may optionally contain additional information -describing partitions of the address space. This can be -used on platforms which have strong conventions about which -portions of a flash are used for what purposes, but which don't -use an on-flash partition table such as RedBoot. - -Each partition is represented as a sub-node of the mtd device. -Each node's name represents the name of the corresponding -partition of the mtd device. - -Flash partitions - - reg : The partition's offset and size within the mtd bank. - - label : (optional) The label / name for this partition. - If omitted, the label is taken from the node name (excluding - the unit address). - - read-only : (optional) This parameter, if present, is a hint to - Linux that this partition should only be mounted - read-only. This is usually used for flash partitions - containing early-boot firmware images or data which should not - be clobbered. +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. Example: diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt new file mode 100644 index 000000000000..03855c8c492a --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nand.txt @@ -0,0 +1,7 @@ +* MTD generic binding + +- nand-ecc-mode : String, operation mode of the NAND ecc mode. + Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", + "soft_bch". +- nand-bus-width : 8 or 16 bus width if not present 8 +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt new file mode 100644 index 000000000000..f114ce1657c2 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -0,0 +1,38 @@ +Representing flash partitions in devicetree + +Partitions can be represented by sub-nodes of an mtd device. This can be used +on platforms which have strong conventions about which portions of a flash are +used for what purposes, but which don't use an on-flash partition table such +as RedBoot. + +#address-cells & #size-cells must both be present in the mtd device and be +equal to 1. + +Required properties: +- reg : The partition's offset and size within the mtd bank. + +Optional properties: +- label : The label / name for this partition. If omitted, the label is taken + from the node name (excluding the unit address). +- read-only : This parameter, if present, is a hint to Linux that this + partition should only be mounted read-only. This is usually used for flash + partitions containing early-boot firmware images or data which should not be + clobbered. + +Examples: + + +flash@0 { + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + uimage@100000 { + reg = <0x0100000 0x200000>; + }; +]; diff --git a/Documentation/devicetree/bindings/mtd/spear_smi.txt b/Documentation/devicetree/bindings/mtd/spear_smi.txt new file mode 100644 index 000000000000..7248aadd89e4 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/spear_smi.txt @@ -0,0 +1,31 @@ +* SPEAr SMI + +Required properties: +- compatible : "st,spear600-smi" +- reg : Address range of the mtd chip +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the STMMAC interrupts +- clock-rate : Functional clock rate of SMI in Hz + +Optional properties: +- st,smi-fast-mode : Flash supports read in fast mode + +Example: + + smi: flash@fc000000 { + compatible = "st,spear600-smi"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xfc000000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <12>; + clock-rate = <50000000>; /* 50MHz */ + + flash@f8000000 { + st,smi-fast-mode; + ... + }; + }; |