diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/wireless')
5 files changed, 1 insertions, 10 deletions
diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt index 86602f264dce..cffb2d6876e3 100644 --- a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt +++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt @@ -11,8 +11,6 @@ Required properties: Optional properties: - brcm,drive-strength : drive strength used for SDIO pins on device in mA (default = 6). - - interrupt-parent : the phandle for the interrupt controller to which the - device interrupts are connected. - interrupts : specifies attributes for the out-of-band interrupt (host-wake). When not specified the device will use in-band SDIO interrupts. - interrupt-names : name of the out-of-band interrupt, which must be set diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt index 59de8646862d..9bf9bbac16e2 100644 --- a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt +++ b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt @@ -29,7 +29,6 @@ Optional properties: - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured to firmware. Firmware will wakeup the host using this pin during suspend/resume. - - interrupt-parent: phandle of the parent interrupt controller - interrupts : interrupt pin number to the cpu. driver will request an irq based on this interrupt number. during system suspend, the irq will be enabled so that the wifi chip can wakeup host platform under certain condition. diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt index 189ae5cad8f7..bb2fcde6f7ff 100644 --- a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt +++ b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt @@ -8,8 +8,6 @@ Required properties: - reg : Chip select address of device - spi-max-frequency : Maximum SPI clocking speed of device in Hz - interrupts : Should contain interrupt line -- interrupt-parent : Should be the phandle for the interrupt controller - that services interrupts for this device - vio-supply : phandle to regulator providing VIO - ti,power-gpio : GPIO connected to chip's PMEN pin diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt index 8f9ced076fe1..cb5c9e1569ca 100644 --- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt @@ -17,9 +17,7 @@ Required properties: * "ti,wl1837" - reg : Chip select address of device - spi-max-frequency : Maximum SPI clocking speed of device in Hz -- interrupt-parent, interrupts : - Should contain parameters for 1 interrupt line. - Interrupt parameters: parent, line number, type. +- interrupts : Should contain parameters for 1 interrupt line. - vwlan-supply : Point the node of the regulator that powers/enable the wl12xx/wl18xx chip diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt index f42f6b0f1bc7..9306c4dadd46 100644 --- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt @@ -20,8 +20,6 @@ Required properties: - interrupts : specifies attributes for the out-of-band interrupt. Optional properties: - - interrupt-parent : the phandle for the interrupt controller to which the - device interrupts are connected. - ref-clock-frequency : ref clock frequency in Hz - tcxo-clock-frequency : tcxo clock frequency in Hz |