diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
8 files changed, 124 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/arm/arm,scmi.txt b/Documentation/devicetree/bindings/arm/arm,scmi.txt index 5f3719ab7075..317a2fc3667a 100644 --- a/Documentation/devicetree/bindings/arm/arm,scmi.txt +++ b/Documentation/devicetree/bindings/arm/arm,scmi.txt @@ -6,7 +6,7 @@ that are provided by the hardware platform it is running on, including power and performance functions. This binding is intended to define the interface the firmware implementing -the SCMI as described in ARM document number ARM DUI 0922B ("ARM System Control +the SCMI as described in ARM document number ARM DEN 0056A ("ARM System Control and Management Interface Platform Design Document")[0] provide for OSPM in the device tree. diff --git a/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt b/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt new file mode 100644 index 000000000000..1442ba5d2d98 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/fsl,dpaa2-console.txt @@ -0,0 +1,11 @@ +DPAA2 console support + +Required properties: + + - compatible + Value type: <string> + Definition: Must be "fsl,dpaa2-console". + - reg + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the region where the MCFBA + (MC firmware base address) register can be found. diff --git a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt index 980e5413d18f..eb35b22f9e23 100644 --- a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt +++ b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt @@ -6,6 +6,8 @@ which then translates it into a corresponding voltage on a rail Required Properties: - compatible: Should be one of the following * qcom,msm8996-rpmpd: RPM Power domain for the msm8996 family of SoC + * qcom,msm8998-rpmpd: RPM Power domain for the msm8998 family of SoC + * qcom,qcs404-rpmpd: RPM Power domain for the qcs404 family of SoC * qcom,sdm845-rpmhpd: RPMh Power domain for the sdm845 family of SoC - #power-domain-cells: number of cells in Power domain specifier must be 1. diff --git a/Documentation/devicetree/bindings/reset/bitmain,bm1880-reset.txt b/Documentation/devicetree/bindings/reset/bitmain,bm1880-reset.txt new file mode 100644 index 000000000000..a6f8455ae6c4 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/bitmain,bm1880-reset.txt @@ -0,0 +1,18 @@ +Bitmain BM1880 SoC Reset Controller +=================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "bitmain,bm1880-reset" +- reg: Offset and length of reset controller space in SCTRL. +- #reset-cells: Must be 1. + +Example: + + rst: reset-controller@c00 { + compatible = "bitmain,bm1880-reset"; + reg = <0xc00 0x8>; + #reset-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt index 2ecf33815d18..13e095182db4 100644 --- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt +++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt @@ -45,6 +45,6 @@ Example: }; -For list of all valid reset indicies see +For list of all valid reset indices see <dt-bindings/reset/imx7-reset.h> for i.MX7 and <dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ diff --git a/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt b/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt index 436d2106e80d..e876f3ce54f6 100644 --- a/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt +++ b/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt @@ -2,8 +2,8 @@ Amlogic Canvas ================================ A canvas is a collection of metadata that describes a pixel buffer. -Those metadata include: width, height, phyaddr, wrapping, block mode -and endianness. +Those metadata include: width, height, phyaddr, wrapping and block mode. +Starting with GXBB the endianness can also be described. Many IPs within Amlogic SoCs rely on canvas indexes to read/write pixel data rather than use the phy addresses directly. For instance, this is the case for @@ -18,7 +18,11 @@ Video Lookup Table -------------------------- Required properties: -- compatible: "amlogic,canvas" +- compatible: has to be one of: + - "amlogic,meson8-canvas", "amlogic,canvas" on Meson8 + - "amlogic,meson8b-canvas", "amlogic,canvas" on Meson8b + - "amlogic,meson8m2-canvas", "amlogic,canvas" on Meson8m2 + - "amlogic,canvas" on GXBB and newer - reg: Base physical address and size of the canvas registers. Example: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt new file mode 100644 index 000000000000..954ffee0a9c4 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.txt @@ -0,0 +1,81 @@ +Qualcomm Always-On Subsystem side channel binding + +This binding describes the hardware component responsible for side channel +requests to the always-on subsystem (AOSS), used for certain power management +requests that is not handled by the standard RPMh interface. Each client in the +SoC has it's own block of message RAM and IRQ for communication with the AOSS. +The protocol used to communicate in the message RAM is known as Qualcomm +Messaging Protocol (QMP) + +The AOSS side channel exposes control over a set of resources, used to control +a set of debug related clocks and to affect the low power state of resources +related to the secondary subsystems. These resources are exposed as a set of +power-domains. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,sdm845-aoss-qmp" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the message RAM for this + client's communication with the AOSS + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the AOSS message IRQ for this client + +- mboxes: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to the mailbox representing the outgoing doorbell + in APCS for this client, as described in mailbox/mailbox.txt + +- #clock-cells: + Usage: optional + Value type: <u32> + Definition: must be 0 + The single clock represents the QDSS clock. + +- #power-domain-cells: + Usage: optional + Value type: <u32> + Definition: must be 1 + The provided power-domains are: + CDSP state (0), LPASS state (1), modem state (2), SLPI + state (3), SPSS state (4) and Venus state (5). + += SUBNODES +The AOSS side channel also provides the controls for three cooling devices, +these are expressed as subnodes of the QMP node. The name of the node is used +to identify the resource and must therefor be "cx", "mx" or "ebi". + +- #cooling-cells: + Usage: optional + Value type: <u32> + Definition: must be 2 + += EXAMPLE + +The following example represents the AOSS side-channel message RAM and the +mechanism exposing the power-domains, as found in SDM845. + + aoss_qmp: qmp@c300000 { + compatible = "qcom,sdm845-aoss-qmp"; + reg = <0x0c300000 0x100000>; + interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>; + mboxes = <&apss_shared 0>; + + #power-domain-cells = <1>; + + cx_cdev: cx { + #cooling-cells = <2>; + }; + + mx_cdev: mx { + #cooling-cells = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt index bcc612cc7423..db501269f47b 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.txt @@ -9,7 +9,7 @@ used for audio/voice services on the QDSP. Value type: <stringlist> Definition: must be "qcom,apr-v<VERSION-NUMBER>", example "qcom,apr-v2" -- reg +- qcom,apr-domain Usage: required Value type: <u32> Definition: Destination processor ID. @@ -49,9 +49,9 @@ by the individual bindings for the specific service The following example represents a QDSP based sound card on a MSM8996 device which uses apr as communication between Apps and QDSP. - apr@4 { + apr { compatible = "qcom,apr-v2"; - reg = <APR_DOMAIN_ADSP>; + qcom,apr-domain = <APR_DOMAIN_ADSP>; q6core@3 { compatible = "qcom,q6core"; |