diff options
Diffstat (limited to 'Documentation/devicetree')
18 files changed, 670 insertions, 44 deletions
diff --git a/Documentation/devicetree/00-INDEX b/Documentation/devicetree/00-INDEX new file mode 100644 index 000000000000..b78f691fd847 --- /dev/null +++ b/Documentation/devicetree/00-INDEX @@ -0,0 +1,10 @@ +Documentation for device trees, a data structure by which bootloaders pass +hardware layout to Linux in a device-independent manner, simplifying hardware +probing. This subsystem is maintained by Grant Likely +<grant.likely@secretlab.ca> and has a mailing list at +https://lists.ozlabs.org/listinfo/devicetree-discuss + +00-INDEX + - this file +booting-without-of.txt + - Booting Linux without Open Firmware, describes history and format of device trees. diff --git a/Documentation/devicetree/bindings/hwmon/ads1015.txt b/Documentation/devicetree/bindings/hwmon/ads1015.txt new file mode 100644 index 000000000000..918a507d1159 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ads1015.txt @@ -0,0 +1,73 @@ +ADS1015 (I2C) + +This device is a 12-bit A-D converter with 4 inputs. + +The inputs can be used single ended or in certain differential combinations. + +For configuration all possible combinations are mapped to 8 channels: + 0: Voltage over AIN0 and AIN1. + 1: Voltage over AIN0 and AIN3. + 2: Voltage over AIN1 and AIN3. + 3: Voltage over AIN2 and AIN3. + 4: Voltage over AIN0 and GND. + 5: Voltage over AIN1 and GND. + 6: Voltage over AIN2 and GND. + 7: Voltage over AIN3 and GND. + +Each channel can be configured individually: + - pga is the programmable gain amplifier (values are full scale) + 0: +/- 6.144 V + 1: +/- 4.096 V + 2: +/- 2.048 V (default) + 3: +/- 1.024 V + 4: +/- 0.512 V + 5: +/- 0.256 V + - data_rate in samples per second + 0: 128 + 1: 250 + 2: 490 + 3: 920 + 4: 1600 (default) + 5: 2400 + 6: 3300 + +1) The /ads1015 node + + Required properties: + + - compatible : must be "ti,ads1015" + - reg : I2C bus address of the device + - #address-cells : must be <1> + - #size-cells : must be <0> + + The node contains child nodes for each channel that the platform uses. + + Example ADS1015 node: + + ads1015@49 { + compatible = "ti,ads1015"; + reg = <0x49>; + #address-cells = <1>; + #size-cells = <0>; + + [ child node definitions... ] + } + +2) channel nodes + + Required properties: + + - reg : the channel number + + Optional properties: + + - ti,gain : the programmable gain amplifier setting + - ti,datarate : the converter data rate + + Example ADS1015 channel node: + + channel@4 { + reg = <4>; + ti,gain = <3>; + ti,datarate = <5>; + }; diff --git a/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt b/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt new file mode 100644 index 000000000000..569b16248514 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt @@ -0,0 +1,93 @@ +CE4100 I2C +---------- + +CE4100 has one PCI device which is described as the I2C-Controller. This +PCI device has three PCI-bars, each bar contains a complete I2C +controller. So we have a total of three independent I2C-Controllers +which share only an interrupt line. +The driver is probed via the PCI-ID and is gathering the information of +attached devices from the devices tree. +Grant Likely recommended to use the ranges property to map the PCI-Bar +number to its physical address and to use this to find the child nodes +of the specific I2C controller. This were his exact words: + + Here's where the magic happens. Each entry in + ranges describes how the parent pci address space + (middle group of 3) is translated to the local + address space (first group of 2) and the size of + each range (last cell). In this particular case, + the first cell of the local address is chosen to be + 1:1 mapped to the BARs, and the second is the + offset from be base of the BAR (which would be + non-zero if you had 2 or more devices mapped off + the same BAR) + + ranges allows the address mapping to be described + in a way that the OS can interpret without + requiring custom device driver code. + +This is an example which is used on FalconFalls: +------------------------------------------------ + i2c-controller@b,2 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "pci8086,2e68.2", + "pci8086,2e68", + "pciclass,ff0000", + "pciclass,ff00"; + + reg = <0x15a00 0x0 0x0 0x0 0x0>; + interrupts = <16 1>; + + /* as described by Grant, the first number in the group of + * three is the bar number followed by the 64bit bar address + * followed by size of the mapping. The bar address + * requires also a valid translation in parents ranges + * property. + */ + ranges = <0 0 0x02000000 0 0xdffe0500 0x100 + 1 0 0x02000000 0 0xdffe0600 0x100 + 2 0 0x02000000 0 0xdffe0700 0x100>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + + /* The first number in the reg property is the + * number of the bar + */ + reg = <0 0 0x100>; + + /* This I2C controller has no devices */ + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + reg = <1 0 0x100>; + + /* This I2C controller has one gpio controller */ + gpio@26 { + #gpio-cells = <2>; + compatible = "ti,pcf8575"; + reg = <0x26>; + gpio-controller; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + reg = <2 0 0x100>; + + gpio@26 { + #gpio-cells = <2>; + compatible = "ti,pcf8575"; + reg = <0x26>; + gpio-controller; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt index c39ac2891951..89a0084df2f7 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt @@ -7,8 +7,13 @@ Required properties: - voltage-ranges : two cells are required, first cell specifies minimum slot voltage (mV), second cell specifies maximum slot voltage (mV). Several ranges could be specified. -- gpios : (optional) may specify GPIOs in this order: Card-Detect GPIO, + +Optional properties: +- gpios : may specify GPIOs in this order: Card-Detect GPIO, Write-Protect GPIO. +- interrupts : the interrupt of a card detect interrupt. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. Example: @@ -20,4 +25,6 @@ Example: &qe_pio_d 15 0>; voltage-ranges = <3300 3300>; spi-max-frequency = <50000000>; + interrupts = <42>; + interrupt-parent = <&PIC>; }; diff --git a/Documentation/devicetree/bindings/open-pic.txt b/Documentation/devicetree/bindings/open-pic.txt new file mode 100644 index 000000000000..909a902dff85 --- /dev/null +++ b/Documentation/devicetree/bindings/open-pic.txt @@ -0,0 +1,98 @@ +* Open PIC Binding + +This binding specifies what properties must be available in the device tree +representation of an Open PIC compliant interrupt controller. This binding is +based on the binding defined for Open PIC in [1] and is a superset of that +binding. + +Required properties: + + NOTE: Many of these descriptions were paraphrased here from [1] to aid + readability. + + - compatible: Specifies the compatibility list for the PIC. The type + shall be <string> and the value shall include "open-pic". + + - reg: Specifies the base physical address(s) and size(s) of this + PIC's addressable register space. The type shall be <prop-encoded-array>. + + - interrupt-controller: The presence of this property identifies the node + as an Open PIC. No property value shall be defined. + + - #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 2. + + - #address-cells: Specifies the number of cells needed to encode an + address. The type shall be <u32> and the value shall be 0. As such, + 'interrupt-map' nodes do not have to specify a parent unit address. + +Optional properties: + + - pic-no-reset: The presence of this property indicates that the PIC + shall not be reset during runtime initialization. No property value shall + be defined. The presence of this property also mandates that any + initialization related to interrupt sources shall be limited to sources + explicitly referenced in the device tree. + +* Interrupt Specifier Definition + + Interrupt specifiers consists of 2 cells encoded as + follows: + + - <1st-cell>: The interrupt-number that identifies the interrupt source. + + - <2nd-cell>: The level-sense information, encoded as follows: + 0 = low-to-high edge triggered + 1 = active low level-sensitive + 2 = active high level-sensitive + 3 = high-to-low edge triggered + +* Examples + +Example 1: + + /* + * An Open PIC interrupt controller + */ + mpic: pic@40000 { + // This is an interrupt controller node. + interrupt-controller; + + // No address cells so that 'interrupt-map' nodes which reference + // this Open PIC node do not need a parent address specifier. + #address-cells = <0>; + + // Two cells to encode interrupt sources. + #interrupt-cells = <2>; + + // Offset address of 0x40000 and size of 0x40000. + reg = <0x40000 0x40000>; + + // Compatible with Open PIC. + compatible = "open-pic"; + + // The PIC shall not be reset. + pic-no-reset; + }; + +Example 2: + + /* + * An interrupt generating device that is wired to an Open PIC. + */ + serial0: serial@4500 { + // Interrupt source '42' that is active high level-sensitive. + // Note that there are only two cells as specified in the interrupt + // parent's '#interrupt-cells' property. + interrupts = <42 2>; + + // The interrupt controller that this device is wired to. + interrupt-parent = <&mpic>; + }; + +* References + +[1] Power.org (TM) Standard for Embedded Power Architecture (TM) Platform + Requirements (ePAPR), Version 1.0, July 2008. + (http://www.power.org/resources/downloads/Power_ePAPR_APPROVED_v1.0.pdf) + diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cache_sram.txt b/Documentation/devicetree/bindings/powerpc/fsl/cache_sram.txt new file mode 100644 index 000000000000..781955f5217d --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cache_sram.txt @@ -0,0 +1,20 @@ +* Freescale PQ3 and QorIQ based Cache SRAM + +Freescale's mpc85xx and some QorIQ platforms provide an +option of configuring a part of (or full) cache memory +as SRAM. This cache SRAM representation in the device +tree should be done as under:- + +Required properties: + +- compatible : should be "fsl,p2020-cache-sram" +- fsl,cache-sram-ctlr-handle : points to the L2 controller +- reg : offset and length of the cache-sram. + +Example: + +cache-sram@fff00000 { + fsl,cache-sram-ctlr-handle = <&L2>; + reg = <0 0xfff00000 0 0x10000>; + compatible = "fsl,p2020-cache-sram"; +}; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt index 71e39cf3215b..8aa10f45ebe6 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpic.txt @@ -1,42 +1,211 @@ -* OpenPIC and its interrupt numbers on Freescale's e500/e600 cores - -The OpenPIC specification does not specify which interrupt source has to -become which interrupt number. This is up to the software implementation -of the interrupt controller. The only requirement is that every -interrupt source has to have an unique interrupt number / vector number. -To accomplish this the current implementation assigns the number zero to -the first source, the number one to the second source and so on until -all interrupt sources have their unique number. -Usually the assigned vector number equals the interrupt number mentioned -in the documentation for a given core / CPU. This is however not true -for the e500 cores (MPC85XX CPUs) where the documentation distinguishes -between internal and external interrupt sources and starts counting at -zero for both of them. - -So what to write for external interrupt source X or internal interrupt -source Y into the device tree? Here is an example: - -The memory map for the interrupt controller in the MPC8544[0] shows, -that the first interrupt source starts at 0x5_0000 (PIC Register Address -Map-Interrupt Source Configuration Registers). This source becomes the -number zero therefore: - External interrupt 0 = interrupt number 0 - External interrupt 1 = interrupt number 1 - External interrupt 2 = interrupt number 2 - ... -Every interrupt number allocates 0x20 bytes register space. So to get -its number it is sufficient to shift the lower 16bits to right by five. -So for the external interrupt 10 we have: - 0x0140 >> 5 = 10 - -After the external sources, the internal sources follow. The in core I2C -controller on the MPC8544 for instance has the internal source number -27. Oo obtain its interrupt number we take the lower 16bits of its memory -address (0x5_0560) and shift it right: - 0x0560 >> 5 = 43 - -Therefore the I2C device node for the MPC8544 CPU has to have the -interrupt number 43 specified in the device tree. - -[0] MPC8544E PowerQUICCTM III, Integrated Host Processor Family Reference Manual - MPC8544ERM Rev. 1 10/2007 +===================================================================== +Freescale MPIC Interrupt Controller Node +Copyright (C) 2010,2011 Freescale Semiconductor Inc. +===================================================================== + +The Freescale MPIC interrupt controller is found on all PowerQUICC +and QorIQ processors and is compatible with the Open PIC. The +notable difference from Open PIC binding is the addition of 2 +additional cells in the interrupt specifier defining interrupt type +information. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Shall include "fsl,mpic". Freescale MPIC + controllers compatible with this binding have Block + Revision Registers BRR1 and BRR2 at offset 0x0 and + 0x10 in the MPIC. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the physical + offset and length of the device's registers within the + CCSR address space. + + - interrupt-controller + Usage: required + Value type: <empty> + Definition: Specifies that this node is an interrupt + controller + + - #interrupt-cells + Usage: required + Value type: <u32> + Definition: Shall be 2 or 4. A value of 2 means that interrupt + specifiers do not contain the interrupt-type or type-specific + information cells. + + - #address-cells + Usage: required + Value type: <u32> + Definition: Shall be 0. + + - pic-no-reset + Usage: optional + Value type: <empty> + Definition: The presence of this property specifies that the + MPIC must not be reset by the client program, and that + the boot program has initialized all interrupt source + configuration registers to a sane state-- masked or + directed at other cores. This ensures that the client + program will not receive interrupts for sources not belonging + to the client. The presence of this property also mandates + that any initialization related to interrupt sources shall + be limited to sources explicitly referenced in the device tree. + +INTERRUPT SPECIFIER DEFINITION + + Interrupt specifiers consists of 4 cells encoded as + follows: + + <1st-cell> interrupt-number + + Identifies the interrupt source. The meaning + depends on the type of interrupt. + + Note: If the interrupt-type cell is undefined + (i.e. #interrupt-cells = 2), this cell + should be interpreted the same as for + interrupt-type 0-- i.e. an external or + normal SoC device interrupt. + + <2nd-cell> level-sense information, encoded as follows: + 0 = low-to-high edge triggered + 1 = active low level-sensitive + 2 = active high level-sensitive + 3 = high-to-low edge triggered + + <3rd-cell> interrupt-type + + The following types are supported: + + 0 = external or normal SoC device interrupt + + The interrupt-number cell contains + the SoC device interrupt number. The + type-specific cell is undefined. The + interrupt-number is derived from the + MPIC a block of registers referred to as + the "Interrupt Source Configuration Registers". + Each source has 32-bytes of registers + (vector/priority and destination) in this + region. So interrupt 0 is at offset 0x0, + interrupt 1 is at offset 0x20, and so on. + + 1 = error interrupt + + The interrupt-number cell contains + the SoC device interrupt number for + the error interrupt. The type-specific + cell identifies the specific error + interrupt number. + + 2 = MPIC inter-processor interrupt (IPI) + + The interrupt-number cell identifies + the MPIC IPI number. The type-specific + cell is undefined. + + 3 = MPIC timer interrupt + + The interrupt-number cell identifies + the MPIC timer number. The type-specific + cell is undefined. + + <4th-cell> type-specific information + + The type-specific cell is encoded as follows: + + - For interrupt-type 1 (error interrupt), + the type-specific cell contains the + bit number of the error interrupt in the + Error Interrupt Summary Register. + +EXAMPLE 1 + /* + * mpic interrupt controller with 4 cells per specifier + */ + mpic: pic@40000 { + compatible = "fsl,mpic"; + interrupt-controller; + #interrupt-cells = <4>; + #address-cells = <0>; + reg = <0x40000 0x40000>; + }; + +EXAMPLE 2 + /* + * The MPC8544 I2C controller node has an internal + * interrupt number of 27. As per the reference manual + * this corresponds to interrupt source configuration + * registers at 0x5_0560. + * + * The interrupt source configuration registers begin + * at 0x5_0000. + * + * To compute the interrupt specifier interrupt number + * + * 0x560 >> 5 = 43 + * + * The interrupt source configuration registers begin + * at 0x5_0000, and so the i2c vector/priority registers + * are at 0x5_0560. + */ + i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + dfsrr; + }; + + +EXAMPLE 3 + /* + * Definition of a node defining the 4 + * MPIC IPI interrupts. Note the interrupt + * type of 2. + */ + ipi@410a0 { + compatible = "fsl,mpic-ipi"; + reg = <0x40040 0x10>; + interrupts = <0 0 2 0 + 1 0 2 0 + 2 0 2 0 + 3 0 2 0>; + }; + +EXAMPLE 4 + /* + * Definition of a node defining the MPIC + * global timers. Note the interrupt + * type of 3. + */ + timer0: timer@41100 { + compatible = "fsl,mpic-global-timer"; + reg = <0x41100 0x100>; + interrupts = <0 0 3 0 + 1 0 3 0 + 2 0 3 0 + 3 0 3 0>; + }; + +EXAMPLE 5 + /* + * Definition of an error interrupt (interupt type 1). + * SoC interrupt number is 16 and the specific error + * interrupt bit in the error interrupt summary register + * is 23. + */ + memory-controller@8000 { + compatible = "fsl,p4080-memory-controller"; + reg = <0x8000 0x1000>; + interrupts = <16 2 1 23>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt index bcc30bac6831..70558c3f3682 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt @@ -5,14 +5,21 @@ Required properties: first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572, etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on the parent type. + - reg : should contain the address and the length of the shared message interrupt register set. + - msi-available-ranges: use <start count> style section to define which msi interrupt can be used in the 256 msi interrupts. This property is optional, without this, all the 256 MSI interrupts can be used. + Each available range must begin and end on a multiple of 32 (i.e. + no splitting an individual MSI register or the associated PIC interrupt). + - interrupts : each one of the interrupts here is one entry per 32 MSIs, and routed to the host interrupt controller. the interrupts should - be set as edge sensitive. + be set as edge sensitive. If msi-available-ranges is present, only + the interrupts that correspond to available ranges shall be present. + - interrupt-parent: the phandle for the interrupt controller that services interrupts for this device. for 83xx cpu, the interrupts are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed diff --git a/Documentation/devicetree/bindings/rtc/rtc-cmos.txt b/Documentation/devicetree/bindings/rtc/rtc-cmos.txt new file mode 100644 index 000000000000..7382989b3052 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-cmos.txt @@ -0,0 +1,28 @@ + Motorola mc146818 compatible RTC +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Required properties: + - compatible : "motorola,mc146818" + - reg : should contain registers location and length. + +Optional properties: + - interrupts : should contain interrupt. + - interrupt-parent : interrupt source phandle. + - ctrl-reg : Contains the initial value of the control register also + called "Register B". + - freq-reg : Contains the initial value of the frequency register also + called "Regsiter A". + +"Register A" and "B" are usually initialized by the firmware (BIOS for +instance). If this is not done, it can be performed by the driver. + +ISA Example: + + rtc@70 { + compatible = "motorola,mc146818"; + interrupts = <8 3>; + interrupt-parent = <&ioapic1>; + ctrl-reg = <2>; + freq-reg = <0x26>; + reg = <1 0x70 2>; + }; diff --git a/Documentation/devicetree/bindings/serial/altera_jtaguart.txt b/Documentation/devicetree/bindings/serial/altera_jtaguart.txt new file mode 100644 index 000000000000..c152f65f9a28 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/altera_jtaguart.txt @@ -0,0 +1,4 @@ +Altera JTAG UART + +Required properties: +- compatible : should be "ALTR,juart-1.0" diff --git a/Documentation/devicetree/bindings/serial/altera_uart.txt b/Documentation/devicetree/bindings/serial/altera_uart.txt new file mode 100644 index 000000000000..71cae3f70100 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/altera_uart.txt @@ -0,0 +1,7 @@ +Altera UART + +Required properties: +- compatible : should be "ALTR,uart-1.0" + +Optional properties: +- clock-frequency : frequency of the clock input to the UART diff --git a/Documentation/devicetree/bindings/serio/altera_ps2.txt b/Documentation/devicetree/bindings/serio/altera_ps2.txt new file mode 100644 index 000000000000..4d9eecc2ef7d --- /dev/null +++ b/Documentation/devicetree/bindings/serio/altera_ps2.txt @@ -0,0 +1,4 @@ +Altera UP PS/2 controller + +Required properties: +- compatible : should be "ALTR,ps2-1.0". diff --git a/Documentation/devicetree/bindings/spi/spi_altera.txt b/Documentation/devicetree/bindings/spi/spi_altera.txt new file mode 100644 index 000000000000..dda375943506 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_altera.txt @@ -0,0 +1,4 @@ +Altera SPI + +Required properties: +- compatible : should be "ALTR,spi-1.0". diff --git a/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt b/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt new file mode 100644 index 000000000000..d95c0b367a04 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt @@ -0,0 +1,12 @@ +OpenCores tiny SPI + +Required properties: +- compatible : should be "opencores,tiny-spi-rtlsvn2". +- gpios : should specify GPIOs used for chipselect. +Optional properties: +- clock-frequency : input clock frequency to the core. +- baud-width: width, in bits, of the programmable divider used to scale + the input clock to SCLK. + +The clock-frequency and baud-width properties are needed only if the divider +is programmable. They are not needed if the divider is fixed. diff --git a/Documentation/devicetree/bindings/x86/ce4100.txt b/Documentation/devicetree/bindings/x86/ce4100.txt new file mode 100644 index 000000000000..b49ae593a60b --- /dev/null +++ b/Documentation/devicetree/bindings/x86/ce4100.txt @@ -0,0 +1,38 @@ +CE4100 Device Tree Bindings +--------------------------- + +The CE4100 SoC uses for in core peripherals the following compatible +format: <vendor>,<chip>-<device>. +Many of the "generic" devices like HPET or IO APIC have the ce4100 +name in their compatible property because they first appeared in this +SoC. + +The CPU node +------------ + cpu@0 { + device_type = "cpu"; + compatible = "intel,ce4100"; + reg = <0>; + lapic = <&lapic0>; + }; + +The reg property describes the CPU number. The lapic property points to +the local APIC timer. + +The SoC node +------------ + +This node describes the in-core peripherals. Required property: + compatible = "intel,ce4100-cp"; + +The PCI node +------------ +This node describes the PCI bus on the SoC. Its property should be + compatible = "intel,ce4100-pci", "pci"; + +If the OS is using the IO-APIC for interrupt routing then the reported +interrupt numbers for devices is no longer true. In order to obtain the +correct interrupt number, the child node which represents the device has +to contain the interrupt property. Besides the interrupt property it has +to contain at least the reg property containing the PCI bus address and +compatible property according to "PCI Bus Binding Revision 2.1". diff --git a/Documentation/devicetree/bindings/x86/interrupt.txt b/Documentation/devicetree/bindings/x86/interrupt.txt new file mode 100644 index 000000000000..7d19f494f19a --- /dev/null +++ b/Documentation/devicetree/bindings/x86/interrupt.txt @@ -0,0 +1,26 @@ +Interrupt chips +--------------- + +* Intel I/O Advanced Programmable Interrupt Controller (IO APIC) + + Required properties: + -------------------- + compatible = "intel,ce4100-ioapic"; + #interrupt-cells = <2>; + + Device's interrupt property: + + interrupts = <P S>; + + The first number (P) represents the interrupt pin which is wired to the + IO APIC. The second number (S) represents the sense of interrupt which + should be configured and can be one of: + 0 - Edge Rising + 1 - Level Low + 2 - Level High + 3 - Edge Falling + +* Local APIC + Required property: + + compatible = "intel,ce4100-lapic"; diff --git a/Documentation/devicetree/bindings/x86/timer.txt b/Documentation/devicetree/bindings/x86/timer.txt new file mode 100644 index 000000000000..c688af58e3bd --- /dev/null +++ b/Documentation/devicetree/bindings/x86/timer.txt @@ -0,0 +1,6 @@ +Timers +------ + +* High Precision Event Timer (HPET) + Required property: + compatible = "intel,ce4100-hpet"; diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index 28b1c9d3d351..55fd2623445b 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -13,6 +13,7 @@ Table of Contents I - Introduction 1) Entry point for arch/powerpc + 2) Entry point for arch/x86 II - The DT block format 1) Header @@ -225,6 +226,25 @@ it with special cases. cannot support both configurations with Book E and configurations with classic Powerpc architectures. +2) Entry point for arch/x86 +------------------------------- + + There is one single 32bit entry point to the kernel at code32_start, + the decompressor (the real mode entry point goes to the same 32bit + entry point once it switched into protected mode). That entry point + supports one calling convention which is documented in + Documentation/x86/boot.txt + The physical pointer to the device-tree block (defined in chapter II) + is passed via setup_data which requires at least boot protocol 2.09. + The type filed is defined as + + #define SETUP_DTB 2 + + This device-tree is used as an extension to the "boot page". As such it + does not parse / consider data which is already covered by the boot + page. This includes memory size, reserved ranges, command line arguments + or initrd address. It simply holds information which can not be retrieved + otherwise like interrupt routing or a list of devices behind an I2C bus. II - The DT block format ======================== |