diff options
Diffstat (limited to 'Documentation/devicetree')
4 files changed, 269 insertions, 21 deletions
diff --git a/Documentation/devicetree/bindings/leds/leds-lm36274.txt b/Documentation/devicetree/bindings/leds/leds-lm36274.txt new file mode 100644 index 000000000000..39c230d59a4d --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm36274.txt @@ -0,0 +1,85 @@ +* Texas Instruments LM36274 4-Channel LCD Backlight Driver w/Integrated Bias + +The LM36274 is an integrated four-channel WLED driver and LCD bias supply. +The backlight boost provides the power to bias four parallel LED strings with +up to 29V total output voltage. The 11-bit LED current is programmable via +the I2C bus and/or controlled via a logic level PWM input from 60 uA to 30 mA. + +Parent device properties are documented in +Documentation/devicetree/bindings/mfd/ti-lmu.txt + +Regulator properties are documented in +Documentation/devicetree/bindings/regulator/lm363x-regulator.txt + +Required backlight properties: + - compatible: + "ti,lm36274-backlight" + - reg : 0 + - #address-cells : 1 + - #size-cells : 0 + - led-sources : Indicates which LED strings will be enabled. + Values from 0-3, sources is 0 based so strings will be + source value + 1. + +Optional backlight properties: + - label : see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt + +Example: + +HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is +controlled by control bank B. + +lm36274@11 { + compatible = "ti,lm36274"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11>; + + enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm363x-regulator"; + + enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>, + <&pioC 1 GPIO_ACTIVE_HIGH>; + + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <7150000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + }; + + backlight { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm36274-backlight"; + + led@0 { + reg = <0>; + led-sources = <0 2>; + label = "white:backlight_cluster"; + linux,default-trigger = "backlight"; + }; + }; +}; + +For more product information please see the link below: +http://www.ti.com/lit/ds/symlink/lm36274.pdf diff --git a/Documentation/devicetree/bindings/leds/leds-lm3697.txt b/Documentation/devicetree/bindings/leds/leds-lm3697.txt new file mode 100644 index 000000000000..63992d732959 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm3697.txt @@ -0,0 +1,73 @@ +* Texas Instruments - LM3697 Highly Efficient White LED Driver + +The LM3697 11-bit LED driver provides high- +performance backlight dimming for 1, 2, or 3 series +LED strings while delivering up to 90% efficiency. + +This device is suitable for display and keypad lighting + +Required properties: + - compatible: + "ti,lm3697" + - reg : I2C slave address + - #address-cells : 1 + - #size-cells : 0 + +Optional properties: + - enable-gpios : GPIO pin to enable/disable the device + - vled-supply : LED supply + +Required child properties: + - reg : 0 - LED is Controlled by bank A + 1 - LED is Controlled by bank B + - led-sources : Indicates which HVLED string is associated to which + control bank. This is a zero based property so + HVLED1 = 0, HVLED2 = 1, HVLED3 = 2. + Additional information is contained + in Documentation/devicetree/bindings/leds/common.txt + +Optional child properties: + - ti,brightness-resolution - see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - ramp-up-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - ramp-down-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - label : see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt + +Example: + +HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is +controlled by control bank B. + +led-controller@36 { + compatible = "ti,lm3697"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x36>; + + enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + vled-supply = <&vbatt>; + + led@0 { + reg = <0>; + led-sources = <0 2>; + ti,brightness-resolution = <2047>; + ramp-up-us = <5000>; + ramp-down-us = <1000>; + label = "white:first_backlight_cluster"; + linux,default-trigger = "backlight"; + }; + + led@1 { + reg = <1>; + led-sources = <1>; + ti,brightness-resolution = <255>; + ramp-up-us = <500>; + ramp-down-us = <1000>; + label = "white:second_backlight_cluster"; + linux,default-trigger = "backlight"; + }; +} + +For more product information please see the link below: +http://www.ti.com/lit/ds/symlink/lm3697.pdf diff --git a/Documentation/devicetree/bindings/leds/leds-spi-byte.txt b/Documentation/devicetree/bindings/leds/leds-spi-byte.txt new file mode 100644 index 000000000000..28b6b2d9091e --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-spi-byte.txt @@ -0,0 +1,44 @@ +* Single Byte SPI LED Device Driver. + +The driver can be used for controllers with a very simple SPI protocol: +- one LED is controlled by a single byte on MOSI +- the value of the byte gives the brightness between two values (lowest to + highest) +- no return value is necessary (no MISO signal) + +The value for lowest and highest brightness is dependent on the device and +therefore on the compatible string. + +Depending on the compatible string some special functions (like hardware +accelerated blinking) might can be supported too. + +The driver currently only supports one LED. The properties of the LED are +configured in a sub-node in the device node. + +Required properties: +- compatible: should be one of + * "ubnt,acb-spi-led" microcontroller (SONiX 8F26E611LA) based device + used for example in Ubiquiti airCube ISP + +Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt +apply. + +LED sub-node properties: +- label: + see Documentation/devicetree/bindings/leds/common.txt +- default-state: + see Documentation/devicetree/bindings/leds/common.txt + Only "on" and "off" are supported. + +Example: + +led-controller@0 { + compatible = "ubnt,acb-spi-led"; + reg = <0>; + spi-max-frequency = <100000>; + + led { + label = "white:status"; + default-state = "on"; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt index 86ca786d54fc..2296b8f24de4 100644 --- a/Documentation/devicetree/bindings/mfd/ti-lmu.txt +++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt @@ -8,7 +8,7 @@ TI LMU driver supports lighting devices below. LM3632 Backlight and regulator LM3633 Backlight, LED and fault monitor LM3695 Backlight - LM3697 Backlight and fault monitor + LM36274 Backlight and regulator Required properties: - compatible: Should be one of: @@ -16,15 +16,32 @@ Required properties: "ti,lm3632" "ti,lm3633" "ti,lm3695" - "ti,lm3697" + "ti,lm36274" - reg: I2C slave address. 0x11 for LM3632 0x29 for LM3631 - 0x36 for LM3633, LM3697 + 0x36 for LM3633 0x63 for LM3695 + 0x11 for LM36274 -Optional property: +Optional properties: - enable-gpios: A GPIO specifier for hardware enable pin. + - ramp-up-us: Current ramping from one brightness level to + the a higher brightness level. + Range from 2048 us - 117.44 s + - ramp-down-us: Current ramping from one brightness level to + the a lower brightness level. + Range from 2048 us - 117.44 s + - ti,brightness-resolution - This determines whether to use 8 bit brightness + mode or 11 bit brightness mode. If this value is + not set the device is defaulted to the preferred + 8bit brightness mode per 7.3.4.1 of the data + sheet. This setting can either be in the parent + node or as part of the LED child nodes. This + is determined by the part itself if the strings + have a common brightness register or individual + brightness registers. + The values are 255 (8bit) or 2047 (11bit). Required node: - backlight: All LMU devices have backlight child nodes. @@ -35,14 +52,15 @@ Optional nodes: Required properties: - compatible: Should be one of: "ti,lm3633-fault-monitor" - "ti,lm3697-fault-monitor" - leds: LED properties for LM3633. Please refer to [2]. + LED properties for LM36274. Please refer to [4]. - regulators: Regulator properties for LM3631 and LM3632. Please refer to [3]. [1] ../leds/backlight/ti-lmu-backlight.txt [2] ../leds/leds-lm3633.txt [3] ../regulator/lm363x-regulator.txt +[4] ../leds/leds-lm36274.txt lm3631@29 { compatible = "ti,lm3631"; @@ -90,7 +108,7 @@ lm3631@29 { lcd_bl { led-sources = <0 1>; - ramp-up-msec = <300>; + ramp-up-us = <300000>; }; }; }; @@ -152,15 +170,15 @@ lm3633@36 { main { label = "main_lcd"; led-sources = <1 2>; - ramp-up-msec = <500>; - ramp-down-msec = <500>; + ramp-up-us = <500000>; + ramp-down-us = <500000>; }; front { label = "front_lcd"; led-sources = <0>; - ramp-up-msec = <1000>; - ramp-down-msec = <0>; + ramp-up-us = <1000000>; + ramp-down-us = <0>; }; }; @@ -201,23 +219,51 @@ lm3695@63 { }; }; -lm3697@36 { - compatible = "ti,lm3697"; - reg = <0x36>; +lm36274@11 { + compatible = "ti,lm36274"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11>; enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + regulators { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm363x-regulator"; - backlight { - compatible = "ti,lm3697-backlight"; + enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>, + <&pioC 1 GPIO_ACTIVE_HIGH>; - lcd { - led-sources = <0 1 2>; - ramp-up-msec = <200>; - ramp-down-msec = <200>; + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <7150000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; }; }; - fault-monitor { - compatible = "ti,lm3697-fault-monitor"; + backlight { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm36274-backlight"; + + led@0 { + reg = <0>; + led-sources = <0 2>; + label = "white:backlight_cluster"; + linux,default-trigger = "backlight"; + }; }; }; |