diff options
Diffstat (limited to 'Documentation/devicetree')
5 files changed, 139 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/common-properties.txt b/Documentation/devicetree/bindings/common-properties.txt index 697714f8d75c..a3448bfa1c82 100644 --- a/Documentation/devicetree/bindings/common-properties.txt +++ b/Documentation/devicetree/bindings/common-properties.txt @@ -1,4 +1,8 @@ Common properties +================= + +Endianness +---------- The Devicetree Specification does not define any properties related to hardware byteswapping, but endianness issues show up frequently in porting Linux to @@ -58,3 +62,25 @@ dev: dev@40031000 { ... little-endian; }; + +Daisy-chained devices +--------------------- + +Many serially-attached GPIO and IIO devices are daisy-chainable. To the +host controller, a daisy-chain appears as a single device, but the number +of inputs and outputs it provides is the sum of inputs and outputs provided +by all of its devices. The driver needs to know how many devices the +daisy-chain comprises to determine the amount of data exchanged, how many +inputs and outputs to register and so on. + +Optional properties: + - #daisy-chained-devices: Number of devices in the daisy-chain (default is 1). + +Example: +gpio@0 { + compatible = "name"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + #daisy-chained-devices = <3>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-max3191x.txt b/Documentation/devicetree/bindings/gpio/gpio-max3191x.txt new file mode 100644 index 000000000000..b3a6444b8f45 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-max3191x.txt @@ -0,0 +1,59 @@ +GPIO driver for Maxim MAX3191x industrial serializer + +Required properties: + - compatible: Must be one of: + "maxim,max31910" + "maxim,max31911" + "maxim,max31912" + "maxim,max31913" + "maxim,max31953" + "maxim,max31963" + - reg: Chip select number. + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be two. For consumer use see gpio.txt. + +Optional properties: + - #daisy-chained-devices: + Number of chips in the daisy-chain (default is 1). + - maxim,modesel-gpios: GPIO pins to configure modesel of each chip. + The number of GPIOs must equal "#daisy-chained-devices" + (if each chip is driven by a separate pin) or 1 + (if all chips are wired to the same pin). + - maxim,fault-gpios: GPIO pins to read fault of each chip. + The number of GPIOs must equal "#daisy-chained-devices" + or 1. + - maxim,db0-gpios: GPIO pins to configure debounce of each chip. + The number of GPIOs must equal "#daisy-chained-devices" + or 1. + - maxim,db1-gpios: GPIO pins to configure debounce of each chip. + The number of GPIOs must equal "maxim,db0-gpios". + - maxim,modesel-8bit: Boolean whether the modesel pin of the chips is + pulled high (8-bit mode). Use this if the modesel pin + is hardwired and consequently "maxim,modesel-gpios" + cannot be specified. By default if neither this nor + "maxim,modesel-gpios" is given, the driver assumes + that modesel is pulled low (16-bit mode). + - maxim,ignore-undervoltage: + Boolean whether to ignore undervoltage alarms signaled + by the "maxim,fault-gpios" or by the status byte + (in 16-bit mode). Use this if the chips are powered + through 5VOUT instead of VCC24V, in which case they + will constantly signal undervoltage. + +For other required and optional properties of SPI slave nodes please refer to +../spi/spi-bus.txt. + +Example: + gpio@0 { + compatible = "maxim,max31913"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + + maxim,modesel-gpios = <&gpio2 23>; + maxim,fault-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>; + maxim,db0-gpios = <&gpio2 25>; + maxim,db1-gpios = <&gpio2 26>; + + spi-max-frequency = <25000000>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-uniphier.txt b/Documentation/devicetree/bindings/gpio/gpio-uniphier.txt new file mode 100644 index 000000000000..fed9158dd913 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-uniphier.txt @@ -0,0 +1,52 @@ +UniPhier GPIO controller + +Required properties: +- compatible: Should be "socionext,uniphier-gpio". +- reg: Specifies offset and length of the register set for the device. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be 2. The first cell is the pin number and the second + cell is used to specify optional parameters. +- interrupt-parent: Specifies the parent interrupt controller. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be 2. The first cell defines the interrupt number. + The second cell bits[3:0] is used to specify trigger type as follows: + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + Valid combinations are 1, 2, 3, 4, 8. +- ngpios: Specifies the number of GPIO lines. +- gpio-ranges: Mapping to pin controller pins (as described in gpio.txt) +- socionext,interrupt-ranges: Specifies an interrupt number mapping between + this GPIO controller and its interrupt parent, in the form of arbitrary + number of <child-interrupt-base parent-interrupt-base length> triplets. + +Optional properties: +- gpio-ranges-group-names: Used for named gpio ranges (as described in gpio.txt) + +Example: + gpio: gpio@55000000 { + compatible = "socionext,uniphier-gpio"; + reg = <0x55000000 0x200>; + interrupt-parent = <&aidet>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 0 0>; + gpio-ranges-group-names = "gpio_range"; + ngpios = <248>; + socionext,interrupt-ranges = <0 48 16>, <16 154 5>, <21 217 3>; + }; + +Consumer Example: + + sdhci0_pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio UNIPHIER_GPIO_PORT(29, 4) GPIO_ACTIVE_LOW>; + }; + +Please note UNIPHIER_GPIO_PORT(29, 4) represents PORT294 in the SoC document. +Unfortunately, only the one's place is octal in the port numbering. (That is, +PORT 8, 9, 18, 19, 28, 29, ... are missing.) UNIPHIER_GPIO_PORT() is a helper +macro to calculate 29 * 8 + 4. diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index 51c86f69995e..41137a1cc099 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -14,6 +14,7 @@ Required Properties: - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller. - "renesas,gpio-r8a7795": for R8A7795 (R-Car H3) compatible GPIO controller. - "renesas,gpio-r8a7796": for R8A7796 (R-Car M3-W) compatible GPIO controller. + - "renesas,gpio-r8a77970": for R8A77970 (R-Car V3M) compatible GPIO controller. - "renesas,rcar-gen1-gpio": for a generic R-Car Gen1 GPIO controller. - "renesas,rcar-gen2-gpio": for a generic R-Car Gen2 or RZ/G1 GPIO controller. - "renesas,rcar-gen3-gpio": for a generic R-Car Gen3 GPIO controller. diff --git a/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt index 4d6c8cdc8586..4a75da7051bd 100644 --- a/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt @@ -29,6 +29,7 @@ controller. - interrupts : The interrupt to the parent controller raised when GPIOs generate the interrupts. - snps,nr-gpios : The number of pins in the port, a single cell. +- resets : Reset line for the controller. Example: |