diff options
Diffstat (limited to 'Documentation/driver-api/tty/n_gsm.rst')
| -rw-r--r-- | Documentation/driver-api/tty/n_gsm.rst | 153 |
1 files changed, 153 insertions, 0 deletions
diff --git a/Documentation/driver-api/tty/n_gsm.rst b/Documentation/driver-api/tty/n_gsm.rst new file mode 100644 index 000000000000..35d7381515b0 --- /dev/null +++ b/Documentation/driver-api/tty/n_gsm.rst @@ -0,0 +1,153 @@ +============================== +GSM 0710 tty multiplexor HOWTO +============================== + +.. contents:: :local: + +This line discipline implements the GSM 07.10 multiplexing protocol +detailed in the following 3GPP document: + + https://www.3gpp.org/ftp/Specs/archive/07_series/07.10/0710-720.zip + +This document give some hints on how to use this driver with GPRS and 3G +modems connected to a physical serial port. + +How to use it +============= + +Config Initiator +---------------- + +#. Initialize the modem in 0710 mux mode (usually ``AT+CMUX=`` command) through + its serial port. Depending on the modem used, you can pass more or less + parameters to this command. + +#. Switch the serial line to using the n_gsm line discipline by using + ``TIOCSETD`` ioctl. + +#. Configure the mux using ``GSMIOC_GETCONF``/``GSMIOC_SETCONF`` ioctl. + +#. Obtain base gsmtty number for the used serial port. + + Major parts of the initialization program + (a good starting point is util-linux-ng/sys-utils/ldattach.c):: + + #include <stdio.h> + #include <stdint.h> + #include <linux/gsmmux.h> + #include <linux/tty.h> + + #define DEFAULT_SPEED B115200 + #define SERIAL_PORT /dev/ttyS0 + + int ldisc = N_GSM0710; + struct gsm_config c; + struct termios configuration; + uint32_t first; + + /* open the serial port connected to the modem */ + fd = open(SERIAL_PORT, O_RDWR | O_NOCTTY | O_NDELAY); + + /* configure the serial port : speed, flow control ... */ + + /* send the AT commands to switch the modem to CMUX mode + and check that it's successful (should return OK) */ + write(fd, "AT+CMUX=0\r", 10); + + /* experience showed that some modems need some time before + being able to answer to the first MUX packet so a delay + may be needed here in some case */ + sleep(3); + + /* use n_gsm line discipline */ + ioctl(fd, TIOCSETD, &ldisc); + + /* get n_gsm configuration */ + ioctl(fd, GSMIOC_GETCONF, &c); + /* we are initiator and need encoding 0 (basic) */ + c.initiator = 1; + c.encapsulation = 0; + /* our modem defaults to a maximum size of 127 bytes */ + c.mru = 127; + c.mtu = 127; + /* set the new configuration */ + ioctl(fd, GSMIOC_SETCONF, &c); + /* get first gsmtty device node */ + ioctl(fd, GSMIOC_GETFIRST, &first); + printf("first muxed line: /dev/gsmtty%i\n", first); + + /* and wait for ever to keep the line discipline enabled */ + daemon(0,0); + pause(); + +#. Use these devices as plain serial ports. + + For example, it's possible: + + - to use *gnokii* to send / receive SMS on ``ttygsm1`` + - to use *ppp* to establish a datalink on ``ttygsm2`` + +#. First close all virtual ports before closing the physical port. + + Note that after closing the physical port the modem is still in multiplexing + mode. This may prevent a successful re-opening of the port later. To avoid + this situation either reset the modem if your hardware allows that or send + a disconnect command frame manually before initializing the multiplexing mode + for the second time. The byte sequence for the disconnect command frame is:: + + 0xf9, 0x03, 0xef, 0x03, 0xc3, 0x16, 0xf9 + +Config Requester +---------------- + +#. Receive ``AT+CMUX=`` command through its serial port, initialize mux mode + config. + +#. Switch the serial line to using the *n_gsm* line discipline by using + ``TIOCSETD`` ioctl. + +#. Configure the mux using ``GSMIOC_GETCONF``/``GSMIOC_SETCONF`` ioctl. + +#. Obtain base gsmtty number for the used serial port:: + + #include <stdio.h> + #include <stdint.h> + #include <linux/gsmmux.h> + #include <linux/tty.h> + #define DEFAULT_SPEED B115200 + #define SERIAL_PORT /dev/ttyS0 + + int ldisc = N_GSM0710; + struct gsm_config c; + struct termios configuration; + uint32_t first; + + /* open the serial port */ + fd = open(SERIAL_PORT, O_RDWR | O_NOCTTY | O_NDELAY); + + /* configure the serial port : speed, flow control ... */ + + /* get serial data and check "AT+CMUX=command" parameter ... */ + + /* use n_gsm line discipline */ + ioctl(fd, TIOCSETD, &ldisc); + + /* get n_gsm configuration */ + ioctl(fd, GSMIOC_GETCONF, &c); + /* we are requester and need encoding 0 (basic) */ + c.initiator = 0; + c.encapsulation = 0; + /* our modem defaults to a maximum size of 127 bytes */ + c.mru = 127; + c.mtu = 127; + /* set the new configuration */ + ioctl(fd, GSMIOC_SETCONF, &c); + /* get first gsmtty device node */ + ioctl(fd, GSMIOC_GETFIRST, &first); + printf("first muxed line: /dev/gsmtty%i\n", first); + + /* and wait for ever to keep the line discipline enabled */ + daemon(0,0); + pause(); + +11-03-08 - Eric Bénard - <eric@eukrea.com> |