diff options
Diffstat (limited to 'Documentation/hwmon/smm665')
| -rw-r--r-- | Documentation/hwmon/smm665 | 157 |
1 files changed, 0 insertions, 157 deletions
diff --git a/Documentation/hwmon/smm665 b/Documentation/hwmon/smm665 deleted file mode 100644 index a341eeedab75..000000000000 --- a/Documentation/hwmon/smm665 +++ /dev/null @@ -1,157 +0,0 @@ -Kernel driver smm665 -==================== - -Supported chips: - * Summit Microelectronics SMM465 - Prefix: 'smm465' - Addresses scanned: - - Datasheet: - http://www.summitmicro.com/prod_select/summary/SMM465/SMM465DS.pdf - * Summit Microelectronics SMM665, SMM665B - Prefix: 'smm665' - Addresses scanned: - - Datasheet: - http://www.summitmicro.com/prod_select/summary/SMM665/SMM665B_2089_20.pdf - * Summit Microelectronics SMM665C - Prefix: 'smm665c' - Addresses scanned: - - Datasheet: - http://www.summitmicro.com/prod_select/summary/SMM665C/SMM665C_2125.pdf - * Summit Microelectronics SMM764 - Prefix: 'smm764' - Addresses scanned: - - Datasheet: - http://www.summitmicro.com/prod_select/summary/SMM764/SMM764_2098.pdf - * Summit Microelectronics SMM766, SMM766B - Prefix: 'smm766' - Addresses scanned: - - Datasheets: - http://www.summitmicro.com/prod_select/summary/SMM766/SMM766_2086.pdf - http://www.summitmicro.com/prod_select/summary/SMM766B/SMM766B_2122.pdf - -Author: Guenter Roeck <linux@roeck-us.net> - - -Module Parameters ------------------ - -* vref: int - Default: 1250 (mV) - Reference voltage on VREF_ADC pin in mV. It should not be necessary to set - this parameter unless a non-default reference voltage is used. - - -Description ------------ - -[From datasheet] The SMM665 is an Active DC Output power supply Controller -that monitors, margins and cascade sequences power. The part monitors six -power supply channels as well as VDD, 12V input, two general-purpose analog -inputs and an internal temperature sensor using a 10-bit ADC. - -Each monitored channel has its own high and low limits, plus a critical -limit. - -Support for SMM465, SMM764, and SMM766 has been implemented but is untested. - - -Usage Notes ------------ - -This driver does not probe for devices, since there is no register which -can be safely used to identify the chip. You will have to instantiate -the devices explicitly. When instantiating the device, you have to specify -its configuration register address. - -Example: the following will load the driver for an SMM665 at address 0x57 -on I2C bus #1: -$ modprobe smm665 -$ echo smm665 0x57 > /sys/bus/i2c/devices/i2c-1/new_device - - -Sysfs entries -------------- - -This driver uses the values in the datasheet to convert ADC register values -into the values specified in the sysfs-interface document. All attributes are -read only. - -Min, max, lcrit, and crit values are used by the chip to trigger external signals -and/or other activity. Triggered signals can include HEALTHY, RST, Power Off, -or Fault depending on the chip configuration. The driver reports values as lcrit -or crit if exceeding the limits triggers RST, Power Off, or Fault, and as min or -max otherwise. For details please see the SMM665 datasheet. - -For SMM465 and SMM764, values for Channel E and F are reported but undefined. - -in1_input 12V input voltage (mV) -in2_input 3.3V (VDD) input voltage (mV) -in3_input Channel A voltage (mV) -in4_input Channel B voltage (mV) -in5_input Channel C voltage (mV) -in6_input Channel D voltage (mV) -in7_input Channel E voltage (mV) -in8_input Channel F voltage (mV) -in9_input AIN1 voltage (mV) -in10_input AIN2 voltage (mV) - -in1_min 12v input minimum voltage (mV) -in2_min 3.3V (VDD) input minimum voltage (mV) -in3_min Channel A minimum voltage (mV) -in4_min Channel B minimum voltage (mV) -in5_min Channel C minimum voltage (mV) -in6_min Channel D minimum voltage (mV) -in7_min Channel E minimum voltage (mV) -in8_min Channel F minimum voltage (mV) -in9_min AIN1 minimum voltage (mV) -in10_min AIN2 minimum voltage (mV) - -in1_max 12v input maximum voltage (mV) -in2_max 3.3V (VDD) input maximum voltage (mV) -in3_max Channel A maximum voltage (mV) -in4_max Channel B maximum voltage (mV) -in5_max Channel C maximum voltage (mV) -in6_max Channel D maximum voltage (mV) -in7_max Channel E maximum voltage (mV) -in8_max Channel F maximum voltage (mV) -in9_max AIN1 maximum voltage (mV) -in10_max AIN2 maximum voltage (mV) - -in1_lcrit 12v input critical minimum voltage (mV) -in2_lcrit 3.3V (VDD) input critical minimum voltage (mV) -in3_lcrit Channel A critical minimum voltage (mV) -in4_lcrit Channel B critical minimum voltage (mV) -in5_lcrit Channel C critical minimum voltage (mV) -in6_lcrit Channel D critical minimum voltage (mV) -in7_lcrit Channel E critical minimum voltage (mV) -in8_lcrit Channel F critical minimum voltage (mV) -in9_lcrit AIN1 critical minimum voltage (mV) -in10_lcrit AIN2 critical minimum voltage (mV) - -in1_crit 12v input critical maximum voltage (mV) -in2_crit 3.3V (VDD) input critical maximum voltage (mV) -in3_crit Channel A critical maximum voltage (mV) -in4_crit Channel B critical maximum voltage (mV) -in5_crit Channel C critical maximum voltage (mV) -in6_crit Channel D critical maximum voltage (mV) -in7_crit Channel E critical maximum voltage (mV) -in8_crit Channel F critical maximum voltage (mV) -in9_crit AIN1 critical maximum voltage (mV) -in10_crit AIN2 critical maximum voltage (mV) - -in1_crit_alarm 12v input critical alarm -in2_crit_alarm 3.3V (VDD) input critical alarm -in3_crit_alarm Channel A critical alarm -in4_crit_alarm Channel B critical alarm -in5_crit_alarm Channel C critical alarm -in6_crit_alarm Channel D critical alarm -in7_crit_alarm Channel E critical alarm -in8_crit_alarm Channel F critical alarm -in9_crit_alarm AIN1 critical alarm -in10_crit_alarm AIN2 critical alarm - -temp1_input Chip temperature -temp1_min Mimimum chip temperature -temp1_max Maximum chip temperature -temp1_crit Critical chip temperature -temp1_crit_alarm Temperature critical alarm |