diff options
Diffstat (limited to 'Documentation/powerpc/dts-bindings/4xx')
| -rw-r--r-- | Documentation/powerpc/dts-bindings/4xx/cpm.txt | 52 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/4xx/emac.txt | 148 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/4xx/ndfc.txt | 39 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt | 93 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/4xx/reboot.txt | 18 |
5 files changed, 0 insertions, 350 deletions
diff --git a/Documentation/powerpc/dts-bindings/4xx/cpm.txt b/Documentation/powerpc/dts-bindings/4xx/cpm.txt deleted file mode 100644 index ee459806d35e..000000000000 --- a/Documentation/powerpc/dts-bindings/4xx/cpm.txt +++ /dev/null @@ -1,52 +0,0 @@ -PPC4xx Clock Power Management (CPM) node - -Required properties: - - compatible : compatible list, currently only "ibm,cpm" - - dcr-access-method : "native" - - dcr-reg : < DCR register range > - -Optional properties: - - er-offset : All 4xx SoCs with a CPM controller have - one of two different order for the CPM - registers. Some have the CPM registers - in the following order (ER,FR,SR). The - others have them in the following order - (SR,ER,FR). For the second case set - er-offset = <1>. - - unused-units : specifier consist of one cell. For each - bit in the cell, the corresponding bit - in CPM will be set to turn off unused - devices. - - idle-doze : specifier consist of one cell. For each - bit in the cell, the corresponding bit - in CPM will be set to turn off unused - devices. This is usually just CPM[CPU]. - - standby : specifier consist of one cell. For each - bit in the cell, the corresponding bit - in CPM will be set on standby and - restored on resume. - - suspend : specifier consist of one cell. For each - bit in the cell, the corresponding bit - in CPM will be set on suspend (mem) and - restored on resume. Note, for standby - and suspend the corresponding bits can - be different or the same. Usually for - standby only class 2 and 3 units are set. - However, the interface does not care. - If they are the same, the additional - power saving will be seeing if support - is available to put the DDR in self - refresh mode and any additional power - saving techniques for the specific SoC. - -Example: - CPM0: cpm { - compatible = "ibm,cpm"; - dcr-access-method = "native"; - dcr-reg = <0x160 0x003>; - er-offset = <0>; - unused-units = <0x00000100>; - idle-doze = <0x02000000>; - standby = <0xfeff0000>; - suspend = <0xfeff791d>; -}; diff --git a/Documentation/powerpc/dts-bindings/4xx/emac.txt b/Documentation/powerpc/dts-bindings/4xx/emac.txt deleted file mode 100644 index 2161334a7ca5..000000000000 --- a/Documentation/powerpc/dts-bindings/4xx/emac.txt +++ /dev/null @@ -1,148 +0,0 @@ - 4xx/Axon EMAC ethernet nodes - - The EMAC ethernet controller in IBM and AMCC 4xx chips, and also - the Axon bridge. To operate this needs to interact with a ths - special McMAL DMA controller, and sometimes an RGMII or ZMII - interface. In addition to the nodes and properties described - below, the node for the OPB bus on which the EMAC sits must have a - correct clock-frequency property. - - i) The EMAC node itself - - Required properties: - - device_type : "network" - - - compatible : compatible list, contains 2 entries, first is - "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, - 405gp, Axon) and second is either "ibm,emac" or - "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", - "ibm,emac4" - - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ> - - interrupt-parent : optional, if needed for interrupt mapping - - reg : <registers mapping> - - local-mac-address : 6 bytes, MAC address - - mal-device : phandle of the associated McMAL node - - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated - with this EMAC - - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated - with this EMAC - - cell-index : 1 cell, hardware index of the EMAC cell on a given - ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on - each Axon chip) - - max-frame-size : 1 cell, maximum frame size supported in bytes - - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048 - - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048. - - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate - thresholds). - For Axon, 0x00000010 - - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) - in bytes. - For Axon, 0x00000100 (I think ...) - - phy-mode : string, mode of operations of the PHY interface. - Supported values are: "mii", "rmii", "smii", "rgmii", - "tbi", "gmii", rtbi", "sgmii". - For Axon on CAB, it is "rgmii" - - mdio-device : 1 cell, required iff using shared MDIO registers - (440EP). phandle of the EMAC to use to drive the - MDIO lines for the PHY used by this EMAC. - - zmii-device : 1 cell, required iff connected to a ZMII. phandle of - the ZMII device node - - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII - channel or 0xffffffff if ZMII is only used for MDIO. - - rgmii-device : 1 cell, required iff connected to an RGMII. phandle - of the RGMII device node. - For Axon: phandle of plb5/plb4/opb/rgmii - - rgmii-channel : 1 cell, required iff connected to an RGMII. Which - RGMII channel is used by this EMAC. - Fox Axon: present, whatever value is appropriate for each - EMAC, that is the content of the current (bogus) "phy-port" - property. - - Optional properties: - - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, - a search is performed. - - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY - for, used if phy-address is absent. bit 0x00000001 is - MDIO address 0. - For Axon it can be absent, though my current driver - doesn't handle phy-address yet so for now, keep - 0x00ffffff in it. - - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - rx-fifo-size). For Axon, either absent or 2048. - - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - tx-fifo-size). For Axon, either absent or 2048. - - tah-device : 1 cell, optional. If connected to a TAH engine for - offload, phandle of the TAH device node. - - tah-channel : 1 cell, optional. If appropriate, channel used on the - TAH engine. - - Example: - - EMAC0: ethernet@40000800 { - device_type = "network"; - compatible = "ibm,emac-440gp", "ibm,emac"; - interrupt-parent = <&UIC1>; - interrupts = <1c 4 1d 4>; - reg = <40000800 70>; - local-mac-address = [00 04 AC E3 1B 1E]; - mal-device = <&MAL0>; - mal-tx-channel = <0 1>; - mal-rx-channel = <0>; - cell-index = <0>; - max-frame-size = <5dc>; - rx-fifo-size = <1000>; - tx-fifo-size = <800>; - phy-mode = "rmii"; - phy-map = <00000001>; - zmii-device = <&ZMII0>; - zmii-channel = <0>; - }; - - ii) McMAL node - - Required properties: - - device_type : "dma-controller" - - compatible : compatible list, containing 2 entries, first is - "ibm,mcmal-CHIP" where CHIP is the host ASIC (like - emac) and the second is either "ibm,mcmal" or - "ibm,mcmal2". - For Axon, "ibm,mcmal-axon","ibm,mcmal2" - - interrupts : <interrupt mapping for the MAL interrupts sources: - 5 sources: tx_eob, rx_eob, serr, txde, rxde>. - For Axon: This is _different_ from the current - firmware. We use the "delayed" interrupts for txeob - and rxeob. Thus we end up with mapping those 5 MPIC - interrupts, all level positive sensitive: 10, 11, 32, - 33, 34 (in decimal) - - dcr-reg : < DCR registers range > - - dcr-parent : if needed for dcr-reg - - num-tx-chans : 1 cell, number of Tx channels - - num-rx-chans : 1 cell, number of Rx channels - - iii) ZMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,zmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,zmii". - For Axon, there is no ZMII node. - - reg : <registers mapping> - - iv) RGMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,rgmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,rgmii". - For Axon, "ibm,rgmii-axon","ibm,rgmii" - - reg : <registers mapping> - - revision : as provided by the RGMII new version register if - available. - For Axon: 0x0000012a - diff --git a/Documentation/powerpc/dts-bindings/4xx/ndfc.txt b/Documentation/powerpc/dts-bindings/4xx/ndfc.txt deleted file mode 100644 index 869f0b5f16e8..000000000000 --- a/Documentation/powerpc/dts-bindings/4xx/ndfc.txt +++ /dev/null @@ -1,39 +0,0 @@ -AMCC NDFC (NanD Flash Controller) - -Required properties: -- compatible : "ibm,ndfc". -- reg : should specify chip select and size used for the chip (0x2000). - -Optional properties: -- ccr : NDFC config and control register value (default 0). -- bank-settings : NDFC bank configuration register value (default 0). - -Notes: -- partition(s) - follows the OF MTD standard for partitions - -Example: - -ndfc@1,0 { - compatible = "ibm,ndfc"; - reg = <0x00000001 0x00000000 0x00002000>; - ccr = <0x00001000>; - bank-settings = <0x80002222>; - #address-cells = <1>; - #size-cells = <1>; - - nand { - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "kernel"; - reg = <0x00000000 0x00200000>; - }; - partition@200000 { - label = "root"; - reg = <0x00200000 0x03E00000>; - }; - }; -}; - - diff --git a/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt b/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt deleted file mode 100644 index 515ebcf1b97d..000000000000 --- a/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt +++ /dev/null @@ -1,93 +0,0 @@ -PPC440SPe DMA/XOR (DMA Controller and XOR Accelerator) - -Device nodes needed for operation of the ppc440spe-adma driver -are specified hereby. These are I2O/DMA, DMA and XOR nodes -for DMA engines and Memory Queue Module node. The latter is used -by ADMA driver for configuration of RAID-6 H/W capabilities of -the PPC440SPe. In addition to the nodes and properties described -below, the ranges property of PLB node must specify ranges for -DMA devices. - - i) The I2O node - - Required properties: - - - compatible : "ibm,i2o-440spe"; - - reg : <registers mapping> - - dcr-reg : <DCR registers range> - - Example: - - I2O: i2o@400100000 { - compatible = "ibm,i2o-440spe"; - reg = <0x00000004 0x00100000 0x100>; - dcr-reg = <0x060 0x020>; - }; - - - ii) The DMA node - - Required properties: - - - compatible : "ibm,dma-440spe"; - - cell-index : 1 cell, hardware index of the DMA engine - (typically 0x0 and 0x1 for DMA0 and DMA1) - - reg : <registers mapping> - - dcr-reg : <DCR registers range> - - interrupts : <interrupt mapping for DMA0/1 interrupts sources: - 2 sources: DMAx CS FIFO Needs Service IRQ (on UIC0) - and DMA Error IRQ (on UIC1). The latter is common - for both DMA engines>. - - interrupt-parent : needed for interrupt mapping - - Example: - - DMA0: dma0@400100100 { - compatible = "ibm,dma-440spe"; - cell-index = <0>; - reg = <0x00000004 0x00100100 0x100>; - dcr-reg = <0x060 0x020>; - interrupt-parent = <&DMA0>; - interrupts = <0 1>; - #interrupt-cells = <1>; - #address-cells = <0>; - #size-cells = <0>; - interrupt-map = < - 0 &UIC0 0x14 4 - 1 &UIC1 0x16 4>; - }; - - - iii) XOR Accelerator node - - Required properties: - - - compatible : "amcc,xor-accelerator"; - - reg : <registers mapping> - - interrupts : <interrupt mapping for XOR interrupt source> - - interrupt-parent : for interrupt mapping - - Example: - - xor-accel@400200000 { - compatible = "amcc,xor-accelerator"; - reg = <0x00000004 0x00200000 0x400>; - interrupt-parent = <&UIC1>; - interrupts = <0x1f 4>; - }; - - - iv) Memory Queue Module node - - Required properties: - - - compatible : "ibm,mq-440spe"; - - dcr-reg : <DCR registers range> - - Example: - - MQ0: mq { - compatible = "ibm,mq-440spe"; - dcr-reg = <0x040 0x020>; - }; - diff --git a/Documentation/powerpc/dts-bindings/4xx/reboot.txt b/Documentation/powerpc/dts-bindings/4xx/reboot.txt deleted file mode 100644 index d7217260589c..000000000000 --- a/Documentation/powerpc/dts-bindings/4xx/reboot.txt +++ /dev/null @@ -1,18 +0,0 @@ -Reboot property to control system reboot on PPC4xx systems: - -By setting "reset_type" to one of the following values, the default -software reset mechanism may be overidden. Here the possible values of -"reset_type": - - 1 - PPC4xx core reset - 2 - PPC4xx chip reset - 3 - PPC4xx system reset (default) - -Example: - - cpu@0 { - device_type = "cpu"; - model = "PowerPC,440SPe"; - ... - reset-type = <2>; /* Use chip-reset */ - }; |