diff options
Diffstat (limited to 'Documentation')
5 files changed, 34 insertions, 11 deletions
diff --git a/Documentation/devicetree/bindings/net/adi,adin.yaml b/Documentation/devicetree/bindings/net/adi,adin.yaml index 69375cb28e92..d95cc691a65f 100644 --- a/Documentation/devicetree/bindings/net/adi,adin.yaml +++ b/Documentation/devicetree/bindings/net/adi,adin.yaml @@ -36,12 +36,6 @@ properties: enum: [ 4, 8, 12, 16, 20, 24 ] default: 8 - adi,disable-energy-detect: - description: | - Disables Energy Detect Powerdown Mode (default disabled, i.e energy detect - is enabled if this property is unspecified) - type: boolean - examples: - | ethernet { @@ -68,6 +62,5 @@ examples: reg = <1>; adi,fifo-depth-bits = <16>; - adi,disable-energy-detect; }; }; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt index 5100358177c9..b921731cd970 100644 --- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -12,8 +12,36 @@ and therefore may overwrite them. KSZ9021: All skew control options are specified in picoseconds. The minimum - value is 0, the maximum value is 3000, and it is incremented by 200ps - steps. + value is 0, the maximum value is 3000, and it can be specified in 200ps + steps, *but* these values are in not fact what you get because this chip's + skew values actually increase in 120ps steps, starting from -840ps. The + incorrect values came from an error in the original KSZ9021 datasheet + before it was corrected in revision 1.2 (Feb 2014), but it is too late to + change the driver now because of the many existing device trees that have + been created using values that go up in increments of 200. + + The following table shows the actual skew delay you will get for each of the + possible devicetree values, and the number that will be programmed into the + corresponding pad skew register: + + Device Tree Value Delay Pad Skew Register Value + ----------------------------------------------------- + 0 -840ps 0000 + 200 -720ps 0001 + 400 -600ps 0010 + 600 -480ps 0011 + 800 -360ps 0100 + 1000 -240ps 0101 + 1200 -120ps 0110 + 1400 0ps 0111 + 1600 120ps 1000 + 1800 240ps 1001 + 2000 360ps 1010 + 2200 480ps 1011 + 2400 600ps 1100 + 2600 720ps 1101 + 2800 840ps 1110 + 3000 960ps 1111 Optional properties: diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index 7ad36213093e..5df4aa7f6811 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -18,6 +18,7 @@ Required properties: R-Car Gen2 and RZ/G1 devices. - "renesas,etheravb-r8a774a1" for the R8A774A1 SoC. + - "renesas,etheravb-r8a774b1" for the R8A774B1 SoC. - "renesas,etheravb-r8a774c0" for the R8A774C0 SoC. - "renesas,etheravb-r8a7795" for the R8A7795 SoC. - "renesas,etheravb-r8a7796" for the R8A7796 SoC. diff --git a/Documentation/devicetree/bindings/net/snps,dwmac.yaml b/Documentation/devicetree/bindings/net/snps,dwmac.yaml index ebe4537a7cce..4845e29411e4 100644 --- a/Documentation/devicetree/bindings/net/snps,dwmac.yaml +++ b/Documentation/devicetree/bindings/net/snps,dwmac.yaml @@ -113,7 +113,7 @@ properties: const: stmmaceth mac-mode: - maxItems: 1 + $ref: ethernet-controller.yaml#/properties/phy-connection-type description: The property is identical to 'phy-mode', and assumes that there is mode converter in-between the MAC & PHY (e.g. GMII-to-RGMII). This converter diff --git a/Documentation/networking/devlink-trap.rst b/Documentation/networking/devlink-trap.rst index c20c7c483664..8e90a85f3bd5 100644 --- a/Documentation/networking/devlink-trap.rst +++ b/Documentation/networking/devlink-trap.rst @@ -143,7 +143,8 @@ be added to the following table: * - ``port_list_is_empty`` - ``drop`` - Traps packets that the device decided to drop in case they need to be - flooded and the flood list is empty + flooded (e.g., unknown unicast, unregistered multicast) and there are + no ports the packets should be flooded to * - ``port_loopback_filter`` - ``drop`` - Traps packets that the device decided to drop in case after layer 2 |