diff options
Diffstat (limited to 'Documentation')
13 files changed, 352 insertions, 26 deletions
diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt new file mode 100644 index 000000000000..0e295c9d8937 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -0,0 +1,62 @@ +Wolfson Arizona class audio SoCs + +These devices are audio SoCs with extensive digital capabilites and a range +of analogue I/O. + +Required properties: + + - compatible : one of the following chip-specific strings: + "wlf,wm5102" + "wlf,wm5110" + - reg : I2C slave address when connected using I2C, chip select number when + using SPI. + + - interrupts : The interrupt line the /IRQ signal for the device is + connected to. + - interrupt-controller : Arizona class devices contain interrupt controllers + and may provide interrupt services to other devices. + - interrupt-parent : The parent interrupt controller. + - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt + + - gpio-controller : Indicates this device is a GPIO controller. + - #gpio-cells : Must be 2. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + + - AVDD1-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply, + SPKVDDL-supply, SPKVDDR-supply : power supplies for the device, as covered + in Documentation/devicetree/bindings/regulator/regulator.txt + +Optional properties: + + - wlf,reset : GPIO specifier for the GPIO controlling /RESET + - wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA + + - wlf,gpio-defaults : A list of GPIO configuration register values. If + absent, no configuration of these registers is performed. If any + entry has a value that is out of range for a 16 bit register then + the chip default will be used. If present exactly five values must + be specified. + +Example: + +codec: wm5102@1a { + compatible = "wlf,wm5102"; + reg = <0x1a>; + interrupts = <347>; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + + gpio-controller; + #gpio-cells = <2>; + + wlf,gpio-defaults = < + 0x00000000, /* AIF1TXLRCLK */ + 0xffffffff, + 0xffffffff, + 0xffffffff, + 0xffffffff, + >; +}; diff --git a/Documentation/devicetree/bindings/sound/adi,adau1701.txt b/Documentation/devicetree/bindings/sound/adi,adau1701.txt new file mode 100644 index 000000000000..547a49b56a62 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,adau1701.txt @@ -0,0 +1,35 @@ +Analog Devices ADAU1701 + +Required properties: + + - compatible: Should contain "adi,adau1701" + - reg: The i2c address. Value depends on the state of ADDR0 + and ADDR1, as wired in hardware. + +Optional properties: + + - reset-gpio: A GPIO spec to define which pin is connected to the + chip's !RESET pin. If specified, the driver will + assert a hardware reset at probe time. + - adi,pll-mode-gpios: An array of two GPIO specs to describe the GPIOs + the ADAU's PLL config pins are connected to. + The state of the pins are set according to the + configured clock divider on ASoC side before the + firmware is loaded. + - adi,pin-config: An array of 12 numerical values selecting one of the + pin configurations as described in the datasheet, + table 53. Note that the value of this property has + to be prefixed with '/bits/ 8'. + +Examples: + + i2c_bus { + adau1701@34 { + compatible = "adi,adau1701"; + reg = <0x34>; + reset-gpio = <&gpio 23 0>; + adi,pll-mode-gpios = <&gpio 24 0 &gpio 25 0>; + adi,pin-config = /bits/ 8 <0x4 0x7 0x5 0x5 0x4 0x4 + 0x4 0x4 0x4 0x4 0x4 0x4>; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt new file mode 100644 index 000000000000..f49450a87890 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt @@ -0,0 +1,46 @@ +Freescale i.MX audio complex with WM8962 codec + +Required properties: +- compatible : "fsl,imx-audio-wm8962" +- model : The user-visible name of this sound complex +- ssi-controller : The phandle of the i.MX SSI controller +- audio-codec : The phandle of the WM8962 audio codec +- audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names could be power + supplies, WM8962 pins, and the jacks on the board: + + Power supplies: + * Mic Bias + + Board connectors: + * Mic Jack + * Headphone Jack + * Ext Spk + +- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) +- mux-ext-port : The external port of the i.MX audio muxer + +Note: The AUDMUX port numbering should start at 1, which is consistent with +hardware manual. + +Example: + +sound { + compatible = "fsl,imx6q-sabresd-wm8962", + "fsl,imx-audio-wm8962"; + model = "wm8962-audio"; + ssi-controller = <&ssi2>; + audio-codec = <&codec>; + audio-routing = + "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "Ext Spk", "SPKOUTL", + "Ext Spk", "SPKOUTR", + "MICBIAS", "AMIC", + "IN3R", "MICBIAS", + "DMIC", "MICBIAS", + "DMICDAT", "DMIC"; + mux-int-port = <2>; + mux-ext-port = <3>; +}; diff --git a/Documentation/devicetree/bindings/sound/mxs-saif.txt b/Documentation/devicetree/bindings/sound/mxs-saif.txt index c37ba6143d9b..7ba07a118e37 100644 --- a/Documentation/devicetree/bindings/sound/mxs-saif.txt +++ b/Documentation/devicetree/bindings/sound/mxs-saif.txt @@ -3,8 +3,11 @@ Required properties: - compatible: Should be "fsl,<chip>-saif" - reg: Should contain registers location and length -- interrupts: Should contain ERROR and DMA interrupts -- fsl,saif-dma-channel: APBX DMA channel for the SAIF +- interrupts: Should contain ERROR interrupt number +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and SAIF DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: Must be "rx-tx". Optional properties: - fsl,saif-master: phandle to the master SAIF. It's only required for @@ -23,14 +26,16 @@ aliases { saif0: saif@80042000 { compatible = "fsl,imx28-saif"; reg = <0x80042000 2000>; - interrupts = <59 80>; - fsl,saif-dma-channel = <4>; + interrupts = <59>; + dmas = <&dma_apbx 4>; + dma-names = "rx-tx"; }; saif1: saif@80046000 { compatible = "fsl,imx28-saif"; reg = <0x80046000 2000>; - interrupts = <58 81>; - fsl,saif-dma-channel = <5>; + interrupts = <58>; + dmas = <&dma_apbx 5>; + dma-names = "rx-tx"; fsl,saif-master = <&saif0>; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt new file mode 100644 index 000000000000..d130818700b2 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt @@ -0,0 +1,71 @@ +NVIDIA Tegra audio complex, with RT5640 CODEC + +Required properties: +- compatible : "nvidia,tegra-audio-rt5640" +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Must include the following entries: + "pll_a" (The Tegra clock of that name), + "pll_a_out0" (The Tegra clock of that name), + "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the RT5640's pins, and the jacks on the board: + + RT5640 pins: + + * DMIC1 + * DMIC2 + * MICBIAS1 + * IN1P + * IN1R + * IN2P + * IN2R + * HPOL + * HPOR + * LOUTL + * LOUTR + * MONOP + * MONON + * SPOLP + * SPOLN + * SPORP + * SPORN + + Board connectors: + + * Headphones + * Speakers + +- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's + connected to the CODEC. +- nvidia,audio-codec : The phandle of the RT5640 audio codec. This binding + assumes that AIF1 on the CODEC is connected to Tegra. + +Optional properties: +- nvidia,hp-det-gpios : The GPIO that detects headphones are plugged in + +Example: + +sound { + compatible = "nvidia,tegra-audio-rt5640-dalmore", + "nvidia,tegra-audio-rt5640"; + nvidia,model = "NVIDIA Tegra Dalmore"; + + nvidia,audio-routing = + "Headphones", "HPOR", + "Headphones", "HPOL", + "Speakers", "SPORP", + "Speakers", "SPORN", + "Speakers", "SPOLP", + "Speakers", "SPOLN"; + + nvidia,i2s-controller = <&tegra_i2s1>; + nvidia,audio-codec = <&rt5640>; + + nvidia,hp-det-gpios = <&gpio 143 0>; /* GPIO PR7 */ + + clocks = <&tegra_car 216>, <&tegra_car 217>, <&tegra_car 120>; + clock-names = "pll_a", "pll_a_out0", "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5640.txt b/Documentation/devicetree/bindings/sound/rt5640.txt new file mode 100644 index 000000000000..005bcb24d72d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5640.txt @@ -0,0 +1,30 @@ +RT5640 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5640". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +- realtek,in1-differential +- realtek,in2-differential + Boolean. Indicate MIC1/2 input are differential, rather than single-ended. + +- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. + +Example: + +rt5640 { + compatible = "realtek,rt5640"; + reg = <0x1c>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>; + realtek,ldo1-en-gpios = + <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 9cc44449508d..955df60a118c 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -5,9 +5,12 @@ Required properties: - reg : the I2C address of the device +- clocks : the clock provider of SYS_MCLK + Example: codec: sgtl5000@0a { compatible = "fsl,sgtl5000"; reg = <0x0a>; + clocks = <&clks 150>; }; diff --git a/Documentation/devicetree/bindings/sound/spdif-receiver.txt b/Documentation/devicetree/bindings/sound/spdif-receiver.txt new file mode 100644 index 000000000000..80f807bf8a1d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/spdif-receiver.txt @@ -0,0 +1,10 @@ +Device-Tree bindings for dummy spdif receiver + +Required properties: + - compatible: should be "linux,spdif-dir". + +Example node: + + codec: spdif-receiver { + compatible = "linux,spdif-dir"; + }; diff --git a/Documentation/devicetree/bindings/sound/spdif-transmitter.txt b/Documentation/devicetree/bindings/sound/spdif-transmitter.txt new file mode 100644 index 000000000000..55a85841dd85 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/spdif-transmitter.txt @@ -0,0 +1,10 @@ +Device-Tree bindings for dummy spdif transmitter + +Required properties: + - compatible: should be "linux,spdif-dit". + +Example node: + + codec: spdif-transmitter { + compatible = "linux,spdif-dit"; + }; diff --git a/Documentation/devicetree/bindings/sound/ssm2518.txt b/Documentation/devicetree/bindings/sound/ssm2518.txt new file mode 100644 index 000000000000..59381a778c79 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ssm2518.txt @@ -0,0 +1,20 @@ +SSM2518 audio amplifier + +This device supports I2C only. + +Required properties: + - compatible : Must be "adi,ssm2518" + - reg : the I2C address of the device. This will either be 0x34 (ADDR pin low) + or 0x35 (ADDR pin high) + +Optional properties: + - gpios : GPIO connected to the nSD pin. If the property is not present it is + assumed that the nSD pin is hardwired to always on. + +Example: + + ssm2518: ssm2518@34 { + compatible = "adi,ssm2518"; + reg = <0x34>; + gpios = <&gpio 5 0>; + }; diff --git a/Documentation/devicetree/bindings/sound/ti,tas5086.txt b/Documentation/devicetree/bindings/sound/ti,tas5086.txt index 8ea4f5b4818d..d2866a0d6a26 100644 --- a/Documentation/devicetree/bindings/sound/ti,tas5086.txt +++ b/Documentation/devicetree/bindings/sound/ti,tas5086.txt @@ -20,6 +20,17 @@ Optional properties: When not specified, the hardware default of 1300ms is retained. + - ti,mid-z-channel-X: Boolean properties, X being a number from 1 to 6. + If given, channel X will start with the Mid-Z start + sequence, otherwise the default Low-Z scheme is used. + + The correct configuration depends on how the power + stages connected to the PWM output pins work. Not all + power stages are compatible to Mid-Z - please refer + to the datasheets for more details. + + Most systems should not set any of these properties. + Examples: i2c_bus { diff --git a/Documentation/devicetree/bindings/sound/wm8962.txt b/Documentation/devicetree/bindings/sound/wm8962.txt index dceb3b1c2bb7..7f82b59ec8f9 100644 --- a/Documentation/devicetree/bindings/sound/wm8962.txt +++ b/Documentation/devicetree/bindings/sound/wm8962.txt @@ -8,9 +8,32 @@ Required properties: - reg : the I2C address of the device. +Optional properties: + - spk-mono: This is a boolean property. If present, the SPK_MONO bit + of R51 (Class D Control 2) gets set, indicating that the speaker is + in mono mode. + + - mic-cfg : Default register value for R48 (Additional Control 4). + If absent, the default should be the register default. + + - gpio-cfg : A list of GPIO configuration register values. The list must + be 6 entries long. If absent, no configuration of these registers is + performed. And note that only the value within [0x0, 0xffff] is valid. + Any other value is regarded as setting the GPIO register by its reset + value 0x0. + Example: codec: wm8962@1a { compatible = "wlf,wm8962"; reg = <0x1a>; + + gpio-cfg = < + 0x0000 /* 0:Default */ + 0x0000 /* 1:Default */ + 0x0013 /* 2:FN_DMICCLK */ + 0x0000 /* 3:Default */ + 0x8014 /* 4:FN_DMICCDAT */ + 0x0000 /* 5:Default */ + >; }; diff --git a/Documentation/sound/alsa/HD-Audio-Models.txt b/Documentation/sound/alsa/HD-Audio-Models.txt index 77d68e23b247..809d72b8eff1 100644 --- a/Documentation/sound/alsa/HD-Audio-Models.txt +++ b/Documentation/sound/alsa/HD-Audio-Models.txt @@ -21,41 +21,41 @@ ALC267/268 ========== inv-dmic Inverted internal mic workaround -ALC269/270/275/276/280/282 +ALC269/270/275/276/28x/29x ====== - laptop-amic Laptops with analog-mic input - laptop-dmic Laptops with digital-mic input - alc269-dmic Enable ALC269(VA) digital mic workaround - alc271-dmic Enable ALC271X digital mic workaround - inv-dmic Inverted internal mic workaround - lenovo-dock Enables docking station I/O for some Lenovos + laptop-amic Laptops with analog-mic input + laptop-dmic Laptops with digital-mic input + alc269-dmic Enable ALC269(VA) digital mic workaround + alc271-dmic Enable ALC271X digital mic workaround + inv-dmic Inverted internal mic workaround + lenovo-dock Enables docking station I/O for some Lenovos dell-headset-multi Headset jack, which can also be used as mic-in dell-headset-dock Headset jack (without mic-in), and also dock I/O -ALC662/663/272 +ALC66x/67x/892 ============== - mario Chromebook mario model fixup - asus-mode1 ASUS - asus-mode2 ASUS - asus-mode3 ASUS - asus-mode4 ASUS - asus-mode5 ASUS - asus-mode6 ASUS - asus-mode7 ASUS - asus-mode8 ASUS - inv-dmic Inverted internal mic workaround + mario Chromebook mario model fixup + asus-mode1 ASUS + asus-mode2 ASUS + asus-mode3 ASUS + asus-mode4 ASUS + asus-mode5 ASUS + asus-mode6 ASUS + asus-mode7 ASUS + asus-mode8 ASUS + inv-dmic Inverted internal mic workaround dell-headset-multi Headset jack, which can also be used as mic-in ALC680 ====== N/A -ALC882/883/885/888/889 +ALC88x/898/1150 ====================== acer-aspire-4930g Acer Aspire 4930G/5930G/6530G/6930G/7730G acer-aspire-8930g Acer Aspire 8330G/6935G acer-aspire Acer Aspire others - inv-dmic Inverted internal mic workaround + inv-dmic Inverted internal mic workaround no-primary-hp VAIO Z/VGC-LN51JGB workaround (for fixed speaker DAC) ALC861/660 |