diff options
Diffstat (limited to 'Documentation')
109 files changed, 4201 insertions, 550 deletions
diff --git a/Documentation/ABI/testing/debugfs-hisi-hpre b/Documentation/ABI/testing/debugfs-hisi-hpre new file mode 100644 index 000000000000..ec4a79e3a807 --- /dev/null +++ b/Documentation/ABI/testing/debugfs-hisi-hpre @@ -0,0 +1,57 @@ +What: /sys/kernel/debug/hisi_hpre/<bdf>/cluster[0-3]/regs +Date: Sep 2019 +Contact: linux-crypto@vger.kernel.org +Description: Dump debug registers from the HPRE cluster. + Only available for PF. + +What: /sys/kernel/debug/hisi_hpre/<bdf>/cluster[0-3]/cluster_ctrl +Date: Sep 2019 +Contact: linux-crypto@vger.kernel.org +Description: Write the HPRE core selection in the cluster into this file, + and then we can read the debug information of the core. + Only available for PF. + +What: /sys/kernel/debug/hisi_hpre/<bdf>/rdclr_en +Date: Sep 2019 +Contact: linux-crypto@vger.kernel.org +Description: HPRE cores debug registers read clear control. 1 means enable + register read clear, otherwise 0. Writing to this file has no + functional effect, only enable or disable counters clear after + reading of these registers. + Only available for PF. + +What: /sys/kernel/debug/hisi_hpre/<bdf>/current_qm +Date: Sep 2019 +Contact: linux-crypto@vger.kernel.org +Description: One HPRE controller has one PF and multiple VFs, each function + has a QM. Select the QM which below qm refers to. + Only available for PF. + +What: /sys/kernel/debug/hisi_hpre/<bdf>/regs +Date: Sep 2019 +Contact: linux-crypto@vger.kernel.org +Description: Dump debug registers from the HPRE. + Only available for PF. + +What: /sys/kernel/debug/hisi_hpre/<bdf>/qm/qm_regs +Date: Sep 2019 +Contact: linux-crypto@vger.kernel.org +Description: Dump debug registers from the QM. + Available for PF and VF in host. VF in guest currently only + has one debug register. + +What: /sys/kernel/debug/hisi_hpre/<bdf>/qm/current_q +Date: Sep 2019 +Contact: linux-crypto@vger.kernel.org +Description: One QM may contain multiple queues. Select specific queue to + show its debug registers in above qm_regs. + Only available for PF. + +What: /sys/kernel/debug/hisi_hpre/<bdf>/qm/clear_enable +Date: Sep 2019 +Contact: linux-crypto@vger.kernel.org +Description: QM debug registers(qm_regs) read clear control. 1 means enable + register read clear, otherwise 0. + Writing to this file has no functional effect, only enable or + disable counters clear after reading of these registers. + Only available for PF. diff --git a/Documentation/ABI/testing/debugfs-hisi-sec b/Documentation/ABI/testing/debugfs-hisi-sec new file mode 100644 index 000000000000..06adb899495e --- /dev/null +++ b/Documentation/ABI/testing/debugfs-hisi-sec @@ -0,0 +1,43 @@ +What: /sys/kernel/debug/hisi_sec/<bdf>/sec_dfx +Date: Oct 2019 +Contact: linux-crypto@vger.kernel.org +Description: Dump the debug registers of SEC cores. + Only available for PF. + +What: /sys/kernel/debug/hisi_sec/<bdf>/clear_enable +Date: Oct 2019 +Contact: linux-crypto@vger.kernel.org +Description: Enabling/disabling of clear action after reading + the SEC debug registers. + 0: disable, 1: enable. + Only available for PF, and take no other effect on SEC. + +What: /sys/kernel/debug/hisi_sec/<bdf>/current_qm +Date: Oct 2019 +Contact: linux-crypto@vger.kernel.org +Description: One SEC controller has one PF and multiple VFs, each function + has a QM. This file can be used to select the QM which below + qm refers to. + Only available for PF. + +What: /sys/kernel/debug/hisi_sec/<bdf>/qm/qm_regs +Date: Oct 2019 +Contact: linux-crypto@vger.kernel.org +Description: Dump of QM related debug registers. + Available for PF and VF in host. VF in guest currently only + has one debug register. + +What: /sys/kernel/debug/hisi_sec/<bdf>/qm/current_q +Date: Oct 2019 +Contact: linux-crypto@vger.kernel.org +Description: One QM of SEC may contain multiple queues. Select specific + queue to show its debug registers in above 'qm_regs'. + Only available for PF. + +What: /sys/kernel/debug/hisi_sec/<bdf>/qm/clear_enable +Date: Oct 2019 +Contact: linux-crypto@vger.kernel.org +Description: Enabling/disabling of clear action after reading + the SEC's QM debug registers. + 0: disable, 1: enable. + Only available for PF, and take no other effect on SEC. diff --git a/Documentation/ABI/testing/procfs-diskstats b/Documentation/ABI/testing/procfs-diskstats index 2c44b4f1b060..70dcaf2481f4 100644 --- a/Documentation/ABI/testing/procfs-diskstats +++ b/Documentation/ABI/testing/procfs-diskstats @@ -29,4 +29,9 @@ Description: 17 - sectors discarded 18 - time spent discarding + Kernel 5.5+ appends two more fields for flush requests: + + 19 - flush requests completed successfully + 20 - time spent flushing + For more details refer to Documentation/admin-guide/iostats.rst diff --git a/Documentation/ABI/testing/sysfs-block b/Documentation/ABI/testing/sysfs-block index f8c7c7126bb1..ed8c14f161ee 100644 --- a/Documentation/ABI/testing/sysfs-block +++ b/Documentation/ABI/testing/sysfs-block @@ -15,6 +15,12 @@ Description: 9 - I/Os currently in progress 10 - time spent doing I/Os (ms) 11 - weighted time spent doing I/Os (ms) + 12 - discards completed + 13 - discards merged + 14 - sectors discarded + 15 - time spent discarding (ms) + 16 - flush requests completed + 17 - time spent flushing (ms) For more details refer Documentation/admin-guide/iostats.rst diff --git a/Documentation/ABI/testing/sysfs-class-net-statistics b/Documentation/ABI/testing/sysfs-class-net-statistics index 397118de7b5e..55db27815361 100644 --- a/Documentation/ABI/testing/sysfs-class-net-statistics +++ b/Documentation/ABI/testing/sysfs-class-net-statistics @@ -51,6 +51,14 @@ Description: packet processing. See the network driver for the exact meaning of this value. +What: /sys/class/<iface>/statistics/rx_errors +Date: April 2005 +KernelVersion: 2.6.12 +Contact: netdev@vger.kernel.org +Description: + Indicates the number of receive errors on this network device. + See the network driver for the exact meaning of this value. + What: /sys/class/<iface>/statistics/rx_fifo_errors Date: April 2005 KernelVersion: 2.6.12 @@ -88,6 +96,14 @@ Description: due to lack of capacity in the receive side. See the network driver for the exact meaning of this value. +What: /sys/class/<iface>/statistics/rx_nohandler +Date: February 2016 +KernelVersion: 4.6 +Contact: netdev@vger.kernel.org +Description: + Indicates the number of received packets that were dropped on + an inactive device by the network core. + What: /sys/class/<iface>/statistics/rx_over_errors Date: April 2005 KernelVersion: 2.6.12 diff --git a/Documentation/admin-guide/cgroup-v2.rst b/Documentation/admin-guide/cgroup-v2.rst index 5361ebec3361..007ba86aef78 100644 --- a/Documentation/admin-guide/cgroup-v2.rst +++ b/Documentation/admin-guide/cgroup-v2.rst @@ -1334,7 +1334,7 @@ PAGE_SIZE multiple when read back. pgdeactivate - Amount of pages moved to the inactive LRU lis + Amount of pages moved to the inactive LRU list pglazyfree diff --git a/Documentation/admin-guide/device-mapper/dm-integrity.rst b/Documentation/admin-guide/device-mapper/dm-integrity.rst index a30aa91b5fbe..594095b54b29 100644 --- a/Documentation/admin-guide/device-mapper/dm-integrity.rst +++ b/Documentation/admin-guide/device-mapper/dm-integrity.rst @@ -177,6 +177,11 @@ bitmap_flush_interval:number The bitmap flush interval in milliseconds. The metadata buffers are synchronized when this interval expires. +fix_padding + Use a smaller padding of the tag area that is more + space-efficient. If this option is not present, large padding is + used - that is for compatibility with older kernels. + The journal mode (D/J), buffer_sectors, journal_watermark, commit_time can be changed when reloading the target (load an inactive table and swap the diff --git a/Documentation/admin-guide/device-mapper/dm-raid.rst b/Documentation/admin-guide/device-mapper/dm-raid.rst index 2fe255b130fb..f6344675e395 100644 --- a/Documentation/admin-guide/device-mapper/dm-raid.rst +++ b/Documentation/admin-guide/device-mapper/dm-raid.rst @@ -417,3 +417,5 @@ Version History deadlock/potential data corruption. Update superblock when specific devices are requested via rebuild. Fix RAID leg rebuild errors. + 1.15.0 Fix size extensions not being synchronized in case of new MD bitmap + pages allocated; also fix those not occuring after previous reductions diff --git a/Documentation/admin-guide/iostats.rst b/Documentation/admin-guide/iostats.rst index 5d63b18bd6d1..4f0462af3ca7 100644 --- a/Documentation/admin-guide/iostats.rst +++ b/Documentation/admin-guide/iostats.rst @@ -121,6 +121,15 @@ Field 15 -- # of milliseconds spent discarding This is the total number of milliseconds spent by all discards (as measured from __make_request() to end_that_request_last()). +Field 16 -- # of flush requests completed + This is the total number of flush requests completed successfully. + + Block layer combines flush requests and executes at most one at a time. + This counts flush requests executed by disk. Not tracked for partitions. + +Field 17 -- # of milliseconds spent flushing + This is the total number of milliseconds spent by all flush requests. + To avoid introducing performance bottlenecks, no locks are held while modifying these counters. This implies that minor inaccuracies may be introduced when changes collide, so (for instance) adding up all the diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 8dee8f68fe15..9b847f06cb19 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -3110,9 +3110,9 @@ [X86,PV_OPS] Disable paravirtualized VMware scheduler clock and use the default one. - no-steal-acc [X86,KVM] Disable paravirtualized steal time accounting. - steal time is computed, but won't influence scheduler - behaviour + no-steal-acc [X86,KVM,ARM64] Disable paravirtualized steal time + accounting. steal time is computed, but won't + influence scheduler behaviour nolapic [X86-32,APIC] Do not enable or use the local APIC. diff --git a/Documentation/admin-guide/perf/imx-ddr.rst b/Documentation/admin-guide/perf/imx-ddr.rst index 517a205abad6..90056e4e8859 100644 --- a/Documentation/admin-guide/perf/imx-ddr.rst +++ b/Documentation/admin-guide/perf/imx-ddr.rst @@ -17,7 +17,8 @@ The "format" directory describes format of the config (event ID) and config1 (AXI filtering) fields of the perf_event_attr structure, see /sys/bus/event_source/ devices/imx8_ddr0/format/. The "events" directory describes the events types hardware supported that can be used with perf tool, see /sys/bus/event_source/ -devices/imx8_ddr0/events/. +devices/imx8_ddr0/events/. The "caps" directory describes filter features implemented +in DDR PMU, see /sys/bus/events_source/devices/imx8_ddr0/caps/. e.g.:: perf stat -a -e imx8_ddr0/cycles/ cmd perf stat -a -e imx8_ddr0/read/,imx8_ddr0/write/ cmd @@ -25,9 +26,12 @@ devices/imx8_ddr0/events/. AXI filtering is only used by CSV modes 0x41 (axid-read) and 0x42 (axid-write) to count reading or writing matches filter setting. Filter setting is various from different DRAM controller implementations, which is distinguished by quirks -in the driver. +in the driver. You also can dump info from userspace, filter in "caps" directory +indicates whether PMU supports AXI ID filter or not; enhanced_filter indicates +whether PMU supports enhanced AXI ID filter or not. Value 0 for un-supported, and +value 1 for supported. -* With DDR_CAP_AXI_ID_FILTER quirk. +* With DDR_CAP_AXI_ID_FILTER quirk(filter: 1, enhanced_filter: 0). Filter is defined with two configuration parts: --AXI_ID defines AxID matching value. --AXI_MASKING defines which bits of AxID are meaningful for the matching. @@ -50,3 +54,8 @@ in the driver. axi_id to monitor a specific id, rather than having to specify axi_mask. e.g.:: perf stat -a -e imx8_ddr0/axid-read,axi_id=0x12/ cmd, which will monitor ARID=0x12 + +* With DDR_CAP_AXI_ID_FILTER_ENHANCED quirk(filter: 1, enhanced_filter: 1). + This is an extension to the DDR_CAP_AXI_ID_FILTER quirk which permits + counting the number of bytes (as opposed to the number of bursts) from DDR + read and write transactions concurrently with another set of data counters. diff --git a/Documentation/admin-guide/perf/thunderx2-pmu.rst b/Documentation/admin-guide/perf/thunderx2-pmu.rst index 08e33675853a..01f158238ae1 100644 --- a/Documentation/admin-guide/perf/thunderx2-pmu.rst +++ b/Documentation/admin-guide/perf/thunderx2-pmu.rst @@ -3,24 +3,26 @@ Cavium ThunderX2 SoC Performance Monitoring Unit (PMU UNCORE) ============================================================= The ThunderX2 SoC PMU consists of independent, system-wide, per-socket -PMUs such as the Level 3 Cache (L3C) and DDR4 Memory Controller (DMC). +PMUs such as the Level 3 Cache (L3C), DDR4 Memory Controller (DMC) and +Cavium Coherent Processor Interconnect (CCPI2). The DMC has 8 interleaved channels and the L3C has 16 interleaved tiles. Events are counted for the default channel (i.e. channel 0) and prorated to the total number of channels/tiles. -The DMC and L3C support up to 4 counters. Counters are independently -programmable and can be started and stopped individually. Each counter -can be set to a different event. Counters are 32-bit and do not support -an overflow interrupt; they are read every 2 seconds. +The DMC and L3C support up to 4 counters, while the CCPI2 supports up to 8 +counters. Counters are independently programmable to different events and +can be started and stopped individually. None of the counters support an +overflow interrupt. DMC and L3C counters are 32-bit and read every 2 seconds. +The CCPI2 counters are 64-bit and assumed not to overflow in normal operation. PMU UNCORE (perf) driver: The thunderx2_pmu driver registers per-socket perf PMUs for the DMC and -L3C devices. Each PMU can be used to count up to 4 events -simultaneously. The PMUs provide a description of their available events -and configuration options under sysfs, see -/sys/devices/uncore_<l3c_S/dmc_S/>; S is the socket id. +L3C devices. Each PMU can be used to count up to 4 (DMC/L3C) or up to 8 +(CCPI2) events simultaneously. The PMUs provide a description of their +available events and configuration options under sysfs, see +/sys/devices/uncore_<l3c_S/dmc_S/ccpi2_S/>; S is the socket id. The driver does not support sampling, therefore "perf record" will not work. Per-task perf sessions are also not supported. diff --git a/Documentation/admin-guide/ras.rst b/Documentation/admin-guide/ras.rst index 2b20f5f7380d..0310db624964 100644 --- a/Documentation/admin-guide/ras.rst +++ b/Documentation/admin-guide/ras.rst @@ -330,9 +330,12 @@ There can be multiple csrows and multiple channels. .. [#f4] Nowadays, the term DIMM (Dual In-line Memory Module) is widely used to refer to a memory module, although there are other memory - packaging alternatives, like SO-DIMM, SIMM, etc. Along this document, - and inside the EDAC system, the term "dimm" is used for all memory - modules, even when they use a different kind of packaging. + packaging alternatives, like SO-DIMM, SIMM, etc. The UEFI + specification (Version 2.7) defines a memory module in the Common + Platform Error Record (CPER) section to be an SMBIOS Memory Device + (Type 17). Along this document, and inside the EDAC subsystem, the term + "dimm" is used for all memory modules, even when they use a + different kind of packaging. Memory controllers allow for several csrows, with 8 csrows being a typical value. Yet, the actual number of csrows depends on the layout of @@ -349,12 +352,14 @@ controllers. The following example will assume 2 channels: | | ``ch0`` | ``ch1`` | +============+===========+===========+ | ``csrow0`` | DIMM_A0 | DIMM_B0 | - +------------+ | | - | ``csrow1`` | | | + | | rank0 | rank0 | + +------------+ - | - | + | ``csrow1`` | rank1 | rank1 | +------------+-----------+-----------+ | ``csrow2`` | DIMM_A1 | DIMM_B1 | - +------------+ | | - | ``csrow3`` | | | + | | rank0 | rank0 | + +------------+ - | - | + | ``csrow3`` | rank1 | rank1 | +------------+-----------+-----------+ In the above example, there are 4 physical slots on the motherboard @@ -374,11 +379,13 @@ which the memory DIMM is placed. Thus, when 1 DIMM is placed in each Channel, the csrows cross both DIMMs. Memory DIMMs come single or dual "ranked". A rank is a populated csrow. -Thus, 2 single ranked DIMMs, placed in slots DIMM_A0 and DIMM_B0 above -will have just one csrow (csrow0). csrow1 will be empty. On the other -hand, when 2 dual ranked DIMMs are similarly placed, then both csrow0 -and csrow1 will be populated. The pattern repeats itself for csrow2 and -csrow3. +In the example above 2 dual ranked DIMMs are similarly placed. Thus, +both csrow0 and csrow1 are populated. On the other hand, when 2 single +ranked DIMMs are placed in slots DIMM_A0 and DIMM_B0, then they will +have just one csrow (csrow0) and csrow1 will be empty. The pattern +repeats itself for csrow2 and csrow3. Also note that some memory +controllers don't have any logic to identify the memory module, see +``rankX`` directories below. The representation of the above is reflected in the directory tree in EDAC's sysfs interface. Starting in directory diff --git a/Documentation/arm64/booting.rst b/Documentation/arm64/booting.rst index d3f3a60fbf25..5d78a6f5b0ae 100644 --- a/Documentation/arm64/booting.rst +++ b/Documentation/arm64/booting.rst @@ -213,6 +213,9 @@ Before jumping into the kernel, the following conditions must be met: - ICC_SRE_EL3.Enable (bit 3) must be initialiased to 0b1. - ICC_SRE_EL3.SRE (bit 0) must be initialised to 0b1. + - ICC_CTLR_EL3.PMHE (bit 6) must be set to the same value across + all CPUs the kernel is executing on, and must stay constant + for the lifetime of the kernel. - If the kernel is entered at EL1: diff --git a/Documentation/arm64/cpu-feature-registers.rst b/Documentation/arm64/cpu-feature-registers.rst index 2955287e9acc..b6e44884e3ad 100644 --- a/Documentation/arm64/cpu-feature-registers.rst +++ b/Documentation/arm64/cpu-feature-registers.rst @@ -168,8 +168,15 @@ infrastructure: +------------------------------+---------+---------+ - 3) MIDR_EL1 - Main ID Register + 3) ID_AA64PFR1_EL1 - Processor Feature Register 1 + +------------------------------+---------+---------+ + | Name | bits | visible | + +------------------------------+---------+---------+ + | SSBS | [7-4] | y | + +------------------------------+---------+---------+ + + 4) MIDR_EL1 - Main ID Register +------------------------------+---------+---------+ | Name | bits | visible | +------------------------------+---------+---------+ @@ -188,11 +195,15 @@ infrastructure: as available on the CPU where it is fetched and is not a system wide safe value. - 4) ID_AA64ISAR1_EL1 - Instruction set attribute register 1 + 5) ID_AA64ISAR1_EL1 - Instruction set attribute register 1 +------------------------------+---------+---------+ | Name | bits | visible | +------------------------------+---------+---------+ + | SB | [39-36] | y | + +------------------------------+---------+---------+ + | FRINTTS | [35-32] | y | + +------------------------------+---------+---------+ | GPI | [31-28] | y | +------------------------------+---------+---------+ | GPA | [27-24] | y | @@ -210,7 +221,7 @@ infrastructure: | DPB | [3-0] | y | +------------------------------+---------+---------+ - 5) ID_AA64MMFR2_EL1 - Memory model feature register 2 + 6) ID_AA64MMFR2_EL1 - Memory model feature register 2 +------------------------------+---------+---------+ | Name | bits | visible | @@ -218,7 +229,7 @@ infrastructure: | AT | [35-32] | y | +------------------------------+---------+---------+ - 6) ID_AA64ZFR0_EL1 - SVE feature ID register 0 + 7) ID_AA64ZFR0_EL1 - SVE feature ID register 0 +------------------------------+---------+---------+ | Name | bits | visible | diff --git a/Documentation/arm64/elf_hwcaps.rst b/Documentation/arm64/elf_hwcaps.rst index 91f79529c58c..7fa3d215ae6a 100644 --- a/Documentation/arm64/elf_hwcaps.rst +++ b/Documentation/arm64/elf_hwcaps.rst @@ -119,10 +119,6 @@ HWCAP_LRCPC HWCAP_DCPOP Functionality implied by ID_AA64ISAR1_EL1.DPB == 0b0001. -HWCAP2_DCPODP - - Functionality implied by ID_AA64ISAR1_EL1.DPB == 0b0010. - HWCAP_SHA3 Functionality implied by ID_AA64ISAR0_EL1.SHA3 == 0b0001. @@ -141,30 +137,6 @@ HWCAP_SHA512 HWCAP_SVE Functionality implied by ID_AA64PFR0_EL1.SVE == 0b0001. -HWCAP2_SVE2 - - Functionality implied by ID_AA64ZFR0_EL1.SVEVer == 0b0001. - -HWCAP2_SVEAES - - Functionality implied by ID_AA64ZFR0_EL1.AES == 0b0001. - -HWCAP2_SVEPMULL - - Functionality implied by ID_AA64ZFR0_EL1.AES == 0b0010. - -HWCAP2_SVEBITPERM - - Functionality implied by ID_AA64ZFR0_EL1.BitPerm == 0b0001. - -HWCAP2_SVESHA3 - - Functionality implied by ID_AA64ZFR0_EL1.SHA3 == 0b0001. - -HWCAP2_SVESM4 - - Functionality implied by ID_AA64ZFR0_EL1.SM4 == 0b0001. - HWCAP_ASIMDFHM Functionality implied by ID_AA64ISAR0_EL1.FHM == 0b0001. @@ -180,13 +152,12 @@ HWCAP_ILRCPC HWCAP_FLAGM Functionality implied by ID_AA64ISAR0_EL1.TS == 0b0001. -HWCAP2_FLAGM2 - - Functionality implied by ID_AA64ISAR0_EL1.TS == 0b0010. - HWCAP_SSBS Functionality implied by ID_AA64PFR1_EL1.SSBS == 0b0010. +HWCAP_SB + Functionality implied by ID_AA64ISAR1_EL1.SB == 0b0001. + HWCAP_PACA Functionality implied by ID_AA64ISAR1_EL1.APA == 0b0001 or ID_AA64ISAR1_EL1.API == 0b0001, as described by @@ -197,6 +168,38 @@ HWCAP_PACG ID_AA64ISAR1_EL1.GPI == 0b0001, as described by Documentation/arm64/pointer-authentication.rst. +HWCAP2_DCPODP + + Functionality implied by ID_AA64ISAR1_EL1.DPB == 0b0010. + +HWCAP2_SVE2 + + Functionality implied by ID_AA64ZFR0_EL1.SVEVer == 0b0001. + +HWCAP2_SVEAES + + Functionality implied by ID_AA64ZFR0_EL1.AES == 0b0001. + +HWCAP2_SVEPMULL + + Functionality implied by ID_AA64ZFR0_EL1.AES == 0b0010. + +HWCAP2_SVEBITPERM + + Functionality implied by ID_AA64ZFR0_EL1.BitPerm == 0b0001. + +HWCAP2_SVESHA3 + + Functionality implied by ID_AA64ZFR0_EL1.SHA3 == 0b0001. + +HWCAP2_SVESM4 + + Functionality implied by ID_AA64ZFR0_EL1.SM4 == 0b0001. + +HWCAP2_FLAGM2 + + Functionality implied by ID_AA64ISAR0_EL1.TS == 0b0010. + HWCAP2_FRINT Functionality implied by ID_AA64ISAR1_EL1.FRINTTS == 0b0001. diff --git a/Documentation/arm64/silicon-errata.rst b/Documentation/arm64/silicon-errata.rst index 5a09661330fc..99b2545455ff 100644 --- a/Documentation/arm64/silicon-errata.rst +++ b/Documentation/arm64/silicon-errata.rst @@ -70,8 +70,12 @@ stable kernels. +----------------+-----------------+-----------------+-----------------------------+ | ARM | Cortex-A57 | #834220 | ARM64_ERRATUM_834220 | +----------------+-----------------+-----------------+-----------------------------+ +| ARM | Cortex-A57 | #1319537 | ARM64_ERRATUM_1319367 | ++----------------+-----------------+-----------------+-----------------------------+ | ARM | Cortex-A72 | #853709 | N/A | +----------------+-----------------+-----------------+-----------------------------+ +| ARM | Cortex-A72 | #1319367 | ARM64_ERRATUM_1319367 | ++----------------+-----------------+-----------------+-----------------------------+ | ARM | Cortex-A73 | #858921 | ARM64_ERRATUM_858921 | +----------------+-----------------+-----------------+-----------------------------+ | ARM | Cortex-A55 | #1024718 | ARM64_ERRATUM_1024718 | @@ -88,6 +92,8 @@ stable kernels. +----------------+-----------------+-----------------+-----------------------------+ | ARM | Neoverse-N1 | #1349291 | N/A | +----------------+-----------------+-----------------+-----------------------------+ +| ARM | Neoverse-N1 | #1542419 | ARM64_ERRATUM_1542419 | ++----------------+-----------------+-----------------+-----------------------------+ | ARM | MMU-500 | #841119,826419 | N/A | +----------------+-----------------+-----------------+-----------------------------+ +----------------+-----------------+-----------------+-----------------------------+ diff --git a/Documentation/block/stat.rst b/Documentation/block/stat.rst index 9c07bc22b0bc..77311335c08b 100644 --- a/Documentation/block/stat.rst +++ b/Documentation/block/stat.rst @@ -41,6 +41,8 @@ discard I/Os requests number of discard I/Os processed discard merges requests number of discard I/Os merged with in-queue I/O discard sectors sectors number of sectors discarded discard ticks milliseconds total wait time for discard requests +flush I/Os requests number of flush I/Os processed +flush ticks milliseconds total wait time for flush requests =============== ============= ================================================= read I/Os, write I/Os, discard I/0s @@ -48,6 +50,14 @@ read I/Os, write I/Os, discard I/0s These values increment when an I/O request completes. +flush I/Os +========== + +These values increment when an flush I/O request completes. + +Block layer combines flush requests and executes at most one at a time. +This counts flush requests executed by disk. Not tracked for partitions. + read merges, write merges, discard merges ========================================= @@ -62,8 +72,8 @@ discarded from this block device. The "sectors" in question are the standard UNIX 512-byte sectors, not any device- or filesystem-specific block size. The counters are incremented when the I/O completes. -read ticks, write ticks, discard ticks -====================================== +read ticks, write ticks, discard ticks, flush ticks +=================================================== These values count the number of milliseconds that I/O requests have waited on this block device. If there are multiple I/O requests waiting, diff --git a/Documentation/bpf/index.rst b/Documentation/bpf/index.rst index 801a6ed3f2e5..4f5410b61441 100644 --- a/Documentation/bpf/index.rst +++ b/Documentation/bpf/index.rst @@ -47,6 +47,15 @@ Program types prog_flow_dissector +Testing BPF +=========== + +.. toctree:: + :maxdepth: 1 + + s390 + + .. Links: .. _Documentation/networking/filter.txt: ../networking/filter.txt .. _man-pages: https://www.kernel.org/doc/man-pages/ diff --git a/Documentation/bpf/prog_flow_dissector.rst b/Documentation/bpf/prog_flow_dissector.rst index a78bf036cadd..4d86780ab0f1 100644 --- a/Documentation/bpf/prog_flow_dissector.rst +++ b/Documentation/bpf/prog_flow_dissector.rst @@ -142,3 +142,6 @@ BPF flow dissector doesn't support exporting all the metadata that in-kernel C-based implementation can export. Notable example is single VLAN (802.1Q) and double VLAN (802.1AD) tags. Please refer to the ``struct bpf_flow_keys`` for a set of information that's currently can be exported from the BPF context. + +When BPF flow dissector is attached to the root network namespace (machine-wide +policy), users can't override it in their child network namespaces. diff --git a/Documentation/bpf/s390.rst b/Documentation/bpf/s390.rst new file mode 100644 index 000000000000..21ecb309daea --- /dev/null +++ b/Documentation/bpf/s390.rst @@ -0,0 +1,205 @@ +=================== +Testing BPF on s390 +=================== + +1. Introduction +*************** + +IBM Z are mainframe computers, which are descendants of IBM System/360 from +year 1964. They are supported by the Linux kernel under the name "s390". This +document describes how to test BPF in an s390 QEMU guest. + +2. One-time setup +***************** + +The following is required to build and run the test suite: + + * s390 GCC + * s390 development headers and libraries + * Clang with BPF support + * QEMU with s390 support + * Disk image with s390 rootfs + +Debian supports installing compiler and libraries for s390 out of the box. +Users of other distros may use debootstrap in order to set up a Debian chroot:: + + sudo debootstrap \ + --variant=minbase \ + --include=sudo \ + testing \ + ./s390-toolchain + sudo mount --rbind /dev ./s390-toolchain/dev + sudo mount --rbind /proc ./s390-toolchain/proc + sudo mount --rbind /sys ./s390-toolchain/sys + sudo chroot ./s390-toolchain + +Once on Debian, the build prerequisites can be installed as follows:: + + sudo dpkg --add-architecture s390x + sudo apt-get update + sudo apt-get install \ + bc \ + bison \ + cmake \ + debootstrap \ + dwarves \ + flex \ + g++ \ + gcc \ + g++-s390x-linux-gnu \ + gcc-s390x-linux-gnu \ + gdb-multiarch \ + git \ + make \ + python3 \ + qemu-system-misc \ + qemu-utils \ + rsync \ + libcap-dev:s390x \ + libelf-dev:s390x \ + libncurses-dev + +Latest Clang targeting BPF can be installed as follows:: + + git clone https://github.com/llvm/llvm-project.git + ln -s ../../clang llvm-project/llvm/tools/ + mkdir llvm-project-build + cd llvm-project-build + cmake \ + -DLLVM_TARGETS_TO_BUILD=BPF \ + -DCMAKE_BUILD_TYPE=Release \ + -DCMAKE_INSTALL_PREFIX=/opt/clang-bpf \ + ../llvm-project/llvm + make + sudo make install + export PATH=/opt/clang-bpf/bin:$PATH + +The disk image can be prepared using a loopback mount and debootstrap:: + + qemu-img create -f raw ./s390.img 1G + sudo losetup -f ./s390.img + sudo mkfs.ext4 /dev/loopX + mkdir ./s390.rootfs + sudo mount /dev/loopX ./s390.rootfs + sudo debootstrap \ + --foreign \ + --arch=s390x \ + --variant=minbase \ + --include=" \ + iproute2, \ + iputils-ping, \ + isc-dhcp-client, \ + kmod, \ + libcap2, \ + libelf1, \ + netcat, \ + procps" \ + testing \ + ./s390.rootfs + sudo umount ./s390.rootfs + sudo losetup -d /dev/loopX + +3. Compilation +************** + +In addition to the usual Kconfig options required to run the BPF test suite, it +is also helpful to select:: + + CONFIG_NET_9P=y + CONFIG_9P_FS=y + CONFIG_NET_9P_VIRTIO=y + CONFIG_VIRTIO_PCI=y + +as that would enable a very easy way to share files with the s390 virtual +machine. + +Compiling kernel, modules and testsuite, as well as preparing gdb scripts to +simplify debugging, can be done using the following commands:: + + make ARCH=s390 CROSS_COMPILE=s390x-linux-gnu- menuconfig + make ARCH=s390 CROSS_COMPILE=s390x-linux-gnu- bzImage modules scripts_gdb + make ARCH=s390 CROSS_COMPILE=s390x-linux-gnu- \ + -C tools/testing/selftests \ + TARGETS=bpf \ + INSTALL_PATH=$PWD/tools/testing/selftests/kselftest_install \ + install + +4. Running the test suite +************************* + +The virtual machine can be started as follows:: + + qemu-system-s390x \ + -cpu max,zpci=on \ + -smp 2 \ + -m 4G \ + -kernel linux/arch/s390/boot/compressed/vmlinux \ + -drive file=./s390.img,if=virtio,format=raw \ + -nographic \ + -append 'root=/dev/vda rw console=ttyS1' \ + -virtfs local,path=./linux,security_model=none,mount_tag=linux \ + -object rng-random,filename=/dev/urandom,id=rng0 \ + -device virtio-rng-ccw,rng=rng0 \ + -netdev user,id=net0 \ + -device virtio-net-ccw,netdev=net0 + +When using this on a real IBM Z, ``-enable-kvm`` may be added for better +performance. When starting the virtual machine for the first time, disk image +setup must be finalized using the following command:: + + /debootstrap/debootstrap --second-stage + +Directory with the code built on the host as well as ``/proc`` and ``/sys`` +need to be mounted as follows:: + + mkdir -p /linux + mount -t 9p linux /linux + mount -t proc proc /proc + mount -t sysfs sys /sys + +After that, the test suite can be run using the following commands:: + + cd /linux/tools/testing/selftests/kselftest_install + ./run_kselftest.sh + +As usual, tests can be also run individually:: + + cd /linux/tools/testing/selftests/bpf + ./test_verifier + +5. Debugging +************ + +It is possible to debug the s390 kernel using QEMU GDB stub, which is activated +by passing ``-s`` to QEMU. + +It is preferable to turn KASLR off, so that gdb would know where to find the +kernel image in memory, by building the kernel with:: + + RANDOMIZE_BASE=n + +GDB can then be attached using the following command:: + + gdb-multiarch -ex 'target remote localhost:1234' ./vmlinux + +6. Network +********** + +In case one needs to use the network in the virtual machine in order to e.g. +install additional packages, it can be configured using:: + + dhclient eth0 + +7. Links +******** + +This document is a compilation of techniques, whose more comprehensive +descriptions can be found by following these links: + +- `Debootstrap <https://wiki.debian.org/EmDebian/CrossDebootstrap>`_ +- `Multiarch <https://wiki.debian.org/Multiarch/HOWTO>`_ +- `Building LLVM <https://llvm.org/docs/CMake.html>`_ +- `Cross-compiling the kernel <https://wiki.gentoo.org/wiki/Embedded_Handbook/General/Cross-compiling_the_kernel>`_ +- `QEMU s390x Guest Support <https://wiki.qemu.org/Documentation/Platforms/S390X>`_ +- `Plan 9 folder sharing over Virtio <https://wiki.qemu.org/Documentation/9psetup>`_ +- `Using GDB with QEMU <https://wiki.osdev.org/Kernel_Debugging#Use_GDB_with_QEMU>`_ diff --git a/Documentation/core-api/printk-formats.rst b/Documentation/core-api/printk-formats.rst index ecbebf4ca8e7..050f34f3a70f 100644 --- a/Documentation/core-api/printk-formats.rst +++ b/Documentation/core-api/printk-formats.rst @@ -79,6 +79,18 @@ has the added benefit of providing a unique identifier. On 64-bit machines the first 32 bits are zeroed. The kernel will print ``(ptrval)`` until it gathers enough entropy. If you *really* want the address see %px below. +Error Pointers +-------------- + +:: + + %pe -ENOSPC + +For printing error pointers (i.e. a pointer for which IS_ERR() is true) +as a symbolic error name. Error values for which no symbolic name is +known are printed in decimal, while a non-ERR_PTR passed as the +argument to %pe gets treated as ordinary %p. + Symbols/Function Pointers ------------------------- diff --git a/Documentation/crypto/api-skcipher.rst b/Documentation/crypto/api-skcipher.rst index 20ba08dddf2e..1aaf8985894b 100644 --- a/Documentation/crypto/api-skcipher.rst +++ b/Documentation/crypto/api-skcipher.rst @@ -5,7 +5,7 @@ Block Cipher Algorithm Definitions :doc: Block Cipher Algorithm Definitions .. kernel-doc:: include/linux/crypto.h - :functions: crypto_alg ablkcipher_alg blkcipher_alg cipher_alg compress_alg + :functions: crypto_alg cipher_alg compress_alg Symmetric Key Cipher API ------------------------ @@ -33,30 +33,3 @@ Single Block Cipher API .. kernel-doc:: include/linux/crypto.h :functions: crypto_alloc_cipher crypto_free_cipher crypto_has_cipher crypto_cipher_blocksize crypto_cipher_setkey crypto_cipher_encrypt_one crypto_cipher_decrypt_one - -Asynchronous Block Cipher API - Deprecated ------------------------------------------- - -.. kernel-doc:: include/linux/crypto.h - :doc: Asynchronous Block Cipher API - -.. kernel-doc:: include/linux/crypto.h - :functions: crypto_free_ablkcipher crypto_has_ablkcipher crypto_ablkcipher_ivsize crypto_ablkcipher_blocksize crypto_ablkcipher_setkey crypto_ablkcipher_reqtfm crypto_ablkcipher_encrypt crypto_ablkcipher_decrypt - -Asynchronous Cipher Request Handle - Deprecated ------------------------------------------------ - -.. kernel-doc:: include/linux/crypto.h - :doc: Asynchronous Cipher Request Handle - -.. kernel-doc:: include/linux/crypto.h - :functions: crypto_ablkcipher_reqsize ablkcipher_request_set_tfm ablkcipher_request_alloc ablkcipher_request_free ablkcipher_request_set_callback ablkcipher_request_set_crypt - -Synchronous Block Cipher API - Deprecated ------------------------------------------ - -.. kernel-doc:: include/linux/crypto.h - :doc: Synchronous Block Cipher API - -.. kernel-doc:: include/linux/crypto.h - :functions: crypto_alloc_blkcipher crypto_free_blkcipher crypto_has_blkcipher crypto_blkcipher_name crypto_blkcipher_ivsize crypto_blkcipher_blocksize crypto_blkcipher_setkey crypto_blkcipher_encrypt crypto_blkcipher_encrypt_iv crypto_blkcipher_decrypt crypto_blkcipher_decrypt_iv crypto_blkcipher_set_iv crypto_blkcipher_get_iv diff --git a/Documentation/crypto/architecture.rst b/Documentation/crypto/architecture.rst index 3eae1ae7f798..646c3380a7ed 100644 --- a/Documentation/crypto/architecture.rst +++ b/Documentation/crypto/architecture.rst @@ -201,10 +201,6 @@ the aforementioned cipher types: - CRYPTO_ALG_TYPE_AEAD Authenticated Encryption with Associated Data (MAC) -- CRYPTO_ALG_TYPE_BLKCIPHER Synchronous multi-block cipher - -- CRYPTO_ALG_TYPE_ABLKCIPHER Asynchronous multi-block cipher - - CRYPTO_ALG_TYPE_KPP Key-agreement Protocol Primitive (KPP) such as an ECDH or DH implementation diff --git a/Documentation/crypto/crypto_engine.rst b/Documentation/crypto/crypto_engine.rst index 3baa23c2cd08..25cf9836c336 100644 --- a/Documentation/crypto/crypto_engine.rst +++ b/Documentation/crypto/crypto_engine.rst @@ -63,8 +63,6 @@ request by using: When your driver receives a crypto_request, you must to transfer it to the crypto engine via one of: -* crypto_transfer_ablkcipher_request_to_engine() - * crypto_transfer_aead_request_to_engine() * crypto_transfer_akcipher_request_to_engine() @@ -75,8 +73,6 @@ the crypto engine via one of: At the end of the request process, a call to one of the following functions is needed: -* crypto_finalize_ablkcipher_request() - * crypto_finalize_aead_request() * crypto_finalize_akcipher_request() diff --git a/Documentation/crypto/devel-algos.rst b/Documentation/crypto/devel-algos.rst index c45c6f400dbd..f9d288015acc 100644 --- a/Documentation/crypto/devel-algos.rst +++ b/Documentation/crypto/devel-algos.rst @@ -128,25 +128,20 @@ process requests that are unaligned. This implies, however, additional overhead as the kernel crypto API needs to perform the realignment of the data which may imply moving of data. -Cipher Definition With struct blkcipher_alg and ablkcipher_alg -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +Cipher Definition With struct skcipher_alg +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ -Struct blkcipher_alg defines a synchronous block cipher whereas struct -ablkcipher_alg defines an asynchronous block cipher. +Struct skcipher_alg defines a multi-block cipher, or more generally, a +length-preserving symmetric cipher algorithm. -Please refer to the single block cipher description for schematics of -the block cipher usage. +Scatterlist handling +~~~~~~~~~~~~~~~~~~~~ -Specifics Of Asynchronous Multi-Block Cipher -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - -There are a couple of specifics to the asynchronous interface. - -First of all, some of the drivers will want to use the Generic -ScatterWalk in case the hardware needs to be fed separate chunks of the -scatterlist which contains the plaintext and will contain the -ciphertext. Please refer to the ScatterWalk interface offered by the -Linux kernel scatter / gather list implementation. +Some drivers will want to use the Generic ScatterWalk in case the +hardware needs to be fed separate chunks of the scatterlist which +contains the plaintext and will contain the ciphertext. Please refer +to the ScatterWalk interface offered by the Linux kernel scatter / +gather list implementation. Hashing [HASH] -------------- diff --git a/Documentation/dev-tools/index.rst b/Documentation/dev-tools/index.rst index b0522a4dd107..09dee10d2592 100644 --- a/Documentation/dev-tools/index.rst +++ b/Documentation/dev-tools/index.rst @@ -24,6 +24,7 @@ whole; patches welcome! gdb-kernel-debugging kgdb kselftest + kunit/index .. only:: subproject and html diff --git a/Documentation/dev-tools/kunit/api/index.rst b/Documentation/dev-tools/kunit/api/index.rst new file mode 100644 index 000000000000..9b9bffe5d41a --- /dev/null +++ b/Documentation/dev-tools/kunit/api/index.rst @@ -0,0 +1,16 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============= +API Reference +============= +.. toctree:: + + test + +This section documents the KUnit kernel testing API. It is divided into the +following sections: + +================================= ============================================== +:doc:`test` documents all of the standard testing API + excluding mocking or mocking related features. +================================= ============================================== diff --git a/Documentation/dev-tools/kunit/api/test.rst b/Documentation/dev-tools/kunit/api/test.rst new file mode 100644 index 000000000000..aaa97f17e5b3 --- /dev/null +++ b/Documentation/dev-tools/kunit/api/test.rst @@ -0,0 +1,11 @@ +.. SPDX-License-Identifier: GPL-2.0 + +======== +Test API +======== + +This file documents all of the standard testing API excluding mocking or mocking +related features. + +.. kernel-doc:: include/kunit/test.h + :internal: diff --git a/Documentation/dev-tools/kunit/faq.rst b/Documentation/dev-tools/kunit/faq.rst new file mode 100644 index 000000000000..bf2095112d89 --- /dev/null +++ b/Documentation/dev-tools/kunit/faq.rst @@ -0,0 +1,62 @@ +.. SPDX-License-Identifier: GPL-2.0 + +========================== +Frequently Asked Questions +========================== + +How is this different from Autotest, kselftest, etc? +==================================================== +KUnit is a unit testing framework. Autotest, kselftest (and some others) are +not. + +A `unit test <https://martinfowler.com/bliki/UnitTest.html>`_ is supposed to +test a single unit of code in isolation, hence the name. A unit test should be +the finest granularity of testing and as such should allow all possible code +paths to be tested in the code under test; this is only possible if the code +under test is very small and does not have any external dependencies outside of +the test's control like hardware. + +There are no testing frameworks currently available for the kernel that do not +require installing the kernel on a test machine or in a VM and all require +tests to be written in userspace and run on the kernel under test; this is true +for Autotest, kselftest, and some others, disqualifying any of them from being +considered unit testing frameworks. + +Does KUnit support running on architectures other than UML? +=========================================================== + +Yes, well, mostly. + +For the most part, the KUnit core framework (what you use to write the tests) +can compile to any architecture; it compiles like just another part of the +kernel and runs when the kernel boots. However, there is some infrastructure, +like the KUnit Wrapper (``tools/testing/kunit/kunit.py``) that does not support +other architectures. + +In short, this means that, yes, you can run KUnit on other architectures, but +it might require more work than using KUnit on UML. + +For more information, see :ref:`kunit-on-non-uml`. + +What is the difference between a unit test and these other kinds of tests? +========================================================================== +Most existing tests for the Linux kernel would be categorized as an integration +test, or an end-to-end test. + +- A unit test is supposed to test a single unit of code in isolation, hence the + name. A unit test should be the finest granularity of testing and as such + should allow all possible code paths to be tested in the code under test; this + is only possible if the code under test is very small and does not have any + external dependencies outside of the test's control like hardware. +- An integration test tests the interaction between a minimal set of components, + usually just two or three. For example, someone might write an integration + test to test the interaction between a driver and a piece of hardware, or to + test the interaction between the userspace libraries the kernel provides and + the kernel itself; however, one of these tests would probably not test the + entire kernel along with hardware interactions and interactions with the + userspace. +- An end-to-end test usually tests the entire system from the perspective of the + code under test. For example, someone might write an end-to-end test for the + kernel by installing a production configuration of the kernel on production + hardware with a production userspace and then trying to exercise some behavior + that depends on interactions between the hardware, the kernel, and userspace. diff --git a/Documentation/dev-tools/kunit/index.rst b/Documentation/dev-tools/kunit/index.rst new file mode 100644 index 000000000000..26ffb46bdf99 --- /dev/null +++ b/Documentation/dev-tools/kunit/index.rst @@ -0,0 +1,79 @@ +.. SPDX-License-Identifier: GPL-2.0 + +========================================= +KUnit - Unit Testing for the Linux Kernel +========================================= + +.. toctree:: + :maxdepth: 2 + + start + usage + api/index + faq + +What is KUnit? +============== + +KUnit is a lightweight unit testing and mocking framework for the Linux kernel. +These tests are able to be run locally on a developer's workstation without a VM +or special hardware. + +KUnit is heavily inspired by JUnit, Python's unittest.mock, and +Googletest/Googlemock for C++. KUnit provides facilities for defining unit test +cases, grouping related test cases into test suites, providing common +infrastructure for running tests, and much more. + +Get started now: :doc:`start` + +Why KUnit? +========== + +A unit test is supposed to test a single unit of code in isolation, hence the +name. A unit test should be the finest granularity of testing and as such should +allow all possible code paths to be tested in the code under test; this is only +possible if the code under test is very small and does not have any external +dependencies outside of the test's control like hardware. + +Outside of KUnit, there are no testing frameworks currently +available for the kernel that do not require installing the kernel on a test +machine or in a VM and all require tests to be written in userspace running on +the kernel; this is true for Autotest, and kselftest, disqualifying +any of them from being considered unit testing frameworks. + +KUnit addresses the problem of being able to run tests without needing a virtual +machine or actual hardware with User Mode Linux. User Mode Linux is a Linux +architecture, like ARM or x86; however, unlike other architectures it compiles +to a standalone program that can be run like any other program directly inside +of a host operating system; to be clear, it does not require any virtualization +support; it is just a regular program. + +KUnit is fast. Excluding build time, from invocation to completion KUnit can run +several dozen tests in only 10 to 20 seconds; this might not sound like a big +deal to some people, but having such fast and easy to run tests fundamentally +changes the way you go about testing and even writing code in the first place. +Linus himself said in his `git talk at Google +<https://gist.github.com/lorn/1272686/revisions#diff-53c65572127855f1b003db4064a94573R874>`_: + + "... a lot of people seem to think that performance is about doing the + same thing, just doing it faster, and that is not true. That is not what + performance is all about. If you can do something really fast, really + well, people will start using it differently." + +In this context Linus was talking about branching and merging, +but this point also applies to testing. If your tests are slow, unreliable, are +difficult to write, and require a special setup or special hardware to run, +then you wait a lot longer to write tests, and you wait a lot longer to run +tests; this means that tests are likely to break, unlikely to test a lot of +things, and are unlikely to be rerun once they pass. If your tests are really +fast, you run them all the time, every time you make a change, and every time +someone sends you some code. Why trust that someone ran all their tests +correctly on every change when you can just run them yourself in less time than +it takes to read their test log? + +How do I use it? +================ + +* :doc:`start` - for new users of KUnit +* :doc:`usage` - for a more detailed explanation of KUnit features +* :doc:`api/index` - for the list of KUnit APIs used for testing diff --git a/Documentation/dev-tools/kunit/start.rst b/Documentation/dev-tools/kunit/start.rst new file mode 100644 index 000000000000..aeeddfafeea2 --- /dev/null +++ b/Documentation/dev-tools/kunit/start.rst @@ -0,0 +1,180 @@ +.. SPDX-License-Identifier: GPL-2.0 + +=============== +Getting Started +=============== + +Installing dependencies +======================= +KUnit has the same dependencies as the Linux kernel. As long as you can build +the kernel, you can run KUnit. + +KUnit Wrapper +============= +Included with KUnit is a simple Python wrapper that helps format the output to +easily use and read KUnit output. It handles building and running the kernel, as +well as formatting the output. + +The wrapper can be run with: + +.. code-block:: bash + + ./tools/testing/kunit/kunit.py run + +Creating a kunitconfig +====================== +The Python script is a thin wrapper around Kbuild as such, it needs to be +configured with a ``kunitconfig`` file. This file essentially contains the +regular Kernel config, with the specific test targets as well. + +.. code-block:: bash + + git clone -b master https://kunit.googlesource.com/kunitconfig $PATH_TO_KUNITCONFIG_REPO + cd $PATH_TO_LINUX_REPO + ln -s $PATH_TO_KUNIT_CONFIG_REPO/kunitconfig kunitconfig + +You may want to add kunitconfig to your local gitignore. + +Verifying KUnit Works +--------------------- + +To make sure that everything is set up correctly, simply invoke the Python +wrapper from your kernel repo: + +.. code-block:: bash + + ./tools/testing/kunit/kunit.py run + +.. note:: + You may want to run ``make mrproper`` first. + +If everything worked correctly, you should see the following: + +.. code-block:: bash + + Generating .config ... + Building KUnit Kernel ... + Starting KUnit Kernel ... + +followed by a list of tests that are run. All of them should be passing. + +.. note:: + Because it is building a lot of sources for the first time, the ``Building + kunit kernel`` step may take a while. + +Writing your first test +======================= + +In your kernel repo let's add some code that we can test. Create a file +``drivers/misc/example.h`` with the contents: + +.. code-block:: c + + int misc_example_add(int left, int right); + +create a file ``drivers/misc/example.c``: + +.. code-block:: c + + #include <linux/errno.h> + + #include "example.h" + + int misc_example_add(int left, int right) + { + return left + right; + } + +Now add the following lines to ``drivers/misc/Kconfig``: + +.. code-block:: kconfig + + config MISC_EXAMPLE + bool "My example" + +and the following lines to ``drivers/misc/Makefile``: + +.. code-block:: make + + obj-$(CONFIG_MISC_EXAMPLE) += example.o + +Now we are ready to write the test. The test will be in +``drivers/misc/example-test.c``: + +.. code-block:: c + + #include <kunit/test.h> + #include "example.h" + + /* Define the test cases. */ + + static void misc_example_add_test_basic(struct kunit *test) + { + KUNIT_EXPECT_EQ(test, 1, misc_example_add(1, 0)); + KUNIT_EXPECT_EQ(test, 2, misc_example_add(1, 1)); + KUNIT_EXPECT_EQ(test, 0, misc_example_add(-1, 1)); + KUNIT_EXPECT_EQ(test, INT_MAX, misc_example_add(0, INT_MAX)); + KUNIT_EXPECT_EQ(test, -1, misc_example_add(INT_MAX, INT_MIN)); + } + + static void misc_example_test_failure(struct kunit *test) + { + KUNIT_FAIL(test, "This test never passes."); + } + + static struct kunit_case misc_example_test_cases[] = { + KUNIT_CASE(misc_example_add_test_basic), + KUNIT_CASE(misc_example_test_failure), + {} + }; + + static struct kunit_suite misc_example_test_suite = { + .name = "misc-example", + .test_cases = misc_example_test_cases, + }; + kunit_test_suite(misc_example_test_suite); + +Now add the following to ``drivers/misc/Kconfig``: + +.. code-block:: kconfig + + config MISC_EXAMPLE_TEST + bool "Test for my example" + depends on MISC_EXAMPLE && KUNIT + +and the following to ``drivers/misc/Makefile``: + +.. code-block:: make + + obj-$(CONFIG_MISC_EXAMPLE_TEST) += example-test.o + +Now add it to your ``kunitconfig``: + +.. code-block:: none + + CONFIG_MISC_EXAMPLE=y + CONFIG_MISC_EXAMPLE_TEST=y + +Now you can run the test: + +.. code-block:: bash + + ./tools/testing/kunit/kunit.py + +You should see the following failure: + +.. code-block:: none + + ... + [16:08:57] [PASSED] misc-example:misc_example_add_test_basic + [16:08:57] [FAILED] misc-example:misc_example_test_failure + [16:08:57] EXPECTATION FAILED at drivers/misc/example-test.c:17 + [16:08:57] This test never passes. + ... + +Congrats! You just wrote your first KUnit test! + +Next Steps +========== +* Check out the :doc:`usage` page for a more + in-depth explanation of KUnit. diff --git a/Documentation/dev-tools/kunit/usage.rst b/Documentation/dev-tools/kunit/usage.rst new file mode 100644 index 000000000000..c6e69634e274 --- /dev/null +++ b/Documentation/dev-tools/kunit/usage.rst @@ -0,0 +1,576 @@ +.. SPDX-License-Identifier: GPL-2.0 + +=========== +Using KUnit +=========== + +The purpose of this document is to describe what KUnit is, how it works, how it +is intended to be used, and all the concepts and terminology that are needed to +understand it. This guide assumes a working knowledge of the Linux kernel and +some basic knowledge of testing. + +For a high level introduction to KUnit, including setting up KUnit for your +project, see :doc:`start`. + +Organization of this document +============================= + +This document is organized into two main sections: Testing and Isolating +Behavior. The first covers what a unit test is and how to use KUnit to write +them. The second covers how to use KUnit to isolate code and make it possible +to unit test code that was otherwise un-unit-testable. + +Testing +======= + +What is KUnit? +-------------- + +"K" is short for "kernel" so "KUnit" is the "(Linux) Kernel Unit Testing +Framework." KUnit is intended first and foremost for writing unit tests; it is +general enough that it can be used to write integration tests; however, this is +a secondary goal. KUnit has no ambition of being the only testing framework for +the kernel; for example, it does not intend to be an end-to-end testing +framework. + +What is Unit Testing? +--------------------- + +A `unit test <https://martinfowler.com/bliki/UnitTest.html>`_ is a test that +tests code at the smallest possible scope, a *unit* of code. In the C +programming language that's a function. + +Unit tests should be written for all the publicly exposed functions in a +compilation unit; so that is all the functions that are exported in either a +*class* (defined below) or all functions which are **not** static. + +Writing Tests +------------- + +Test Cases +~~~~~~~~~~ + +The fundamental unit in KUnit is the test case. A test case is a function with +the signature ``void (*)(struct kunit *test)``. It calls a function to be tested +and then sets *expectations* for what should happen. For example: + +.. code-block:: c + + void example_test_success(struct kunit *test) + { + } + + void example_test_failure(struct kunit *test) + { + KUNIT_FAIL(test, "This test never passes."); + } + +In the above example ``example_test_success`` always passes because it does +nothing; no expectations are set, so all expectations pass. On the other hand +``example_test_failure`` always fails because it calls ``KUNIT_FAIL``, which is +a special expectation that logs a message and causes the test case to fail. + +Expectations +~~~~~~~~~~~~ +An *expectation* is a way to specify that you expect a piece of code to do +something in a test. An expectation is called like a function. A test is made +by setting expectations about the behavior of a piece of code under test; when +one or more of the expectations fail, the test case fails and information about +the failure is logged. For example: + +.. code-block:: c + + void add_test_basic(struct kunit *test) + { + KUNIT_EXPECT_EQ(test, 1, add(1, 0)); + KUNIT_EXPECT_EQ(test, 2, add(1, 1)); + } + +In the above example ``add_test_basic`` makes a number of assertions about the +behavior of a function called ``add``; the first parameter is always of type +``struct kunit *``, which contains information about the current test context; +the second parameter, in this case, is what the value is expected to be; the +last value is what the value actually is. If ``add`` passes all of these +expectations, the test case, ``add_test_basic`` will pass; if any one of these +expectations fail, the test case will fail. + +It is important to understand that a test case *fails* when any expectation is +violated; however, the test will continue running, potentially trying other +expectations until the test case ends or is otherwise terminated. This is as +opposed to *assertions* which are discussed later. + +To learn about more expectations supported by KUnit, see :doc:`api/test`. + +.. note:: + A single test case should be pretty short, pretty easy to understand, + focused on a single behavior. + +For example, if we wanted to properly test the add function above, we would +create additional tests cases which would each test a different property that an +add function should have like this: + +.. code-block:: c + + void add_test_basic(struct kunit *test) + { + KUNIT_EXPECT_EQ(test, 1, add(1, 0)); + KUNIT_EXPECT_EQ(test, 2, add(1, 1)); + } + + void add_test_negative(struct kunit *test) + { + KUNIT_EXPECT_EQ(test, 0, add(-1, 1)); + } + + void add_test_max(struct kunit *test) + { + KUNIT_EXPECT_EQ(test, INT_MAX, add(0, INT_MAX)); + KUNIT_EXPECT_EQ(test, -1, add(INT_MAX, INT_MIN)); + } + + void add_test_overflow(struct kunit *test) + { + KUNIT_EXPECT_EQ(test, INT_MIN, add(INT_MAX, 1)); + } + +Notice how it is immediately obvious what all the properties that we are testing +for are. + +Assertions +~~~~~~~~~~ + +KUnit also has the concept of an *assertion*. An assertion is just like an +expectation except the assertion immediately terminates the test case if it is +not satisfied. + +For example: + +.. code-block:: c + + static void mock_test_do_expect_default_return(struct kunit *test) + { + struct mock_test_context *ctx = test->priv; + struct mock *mock = ctx->mock; + int param0 = 5, param1 = -5; + const char *two_param_types[] = {"int", "int"}; + const void *two_params[] = {¶m0, ¶m1}; + const void *ret; + + ret = mock->do_expect(mock, + "test_printk", test_printk, + two_param_types, two_params, + ARRAY_SIZE(two_params)); + KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ret); + KUNIT_EXPECT_EQ(test, -4, *((int *) ret)); + } + +In this example, the method under test should return a pointer to a value, so +if the pointer returned by the method is null or an errno, we don't want to +bother continuing the test since the following expectation could crash the test +case. `ASSERT_NOT_ERR_OR_NULL(...)` allows us to bail out of the test case if +the appropriate conditions have not been satisfied to complete the test. + +Test Suites +~~~~~~~~~~~ + +Now obviously one unit test isn't very helpful; the power comes from having +many test cases covering all of your behaviors. Consequently it is common to +have many *similar* tests; in order to reduce duplication in these closely +related tests most unit testing frameworks provide the concept of a *test +suite*, in KUnit we call it a *test suite*; all it is is just a collection of +test cases for a unit of code with a set up function that gets invoked before +every test cases and then a tear down function that gets invoked after every +test case completes. + +Example: + +.. code-block:: c + + static struct kunit_case example_test_cases[] = { + KUNIT_CASE(example_test_foo), + KUNIT_CASE(example_test_bar), + KUNIT_CASE(example_test_baz), + {} + }; + + static struct kunit_suite example_test_suite = { + .name = "example", + .init = example_test_init, + .exit = example_test_exit, + .test_cases = example_test_cases, + }; + kunit_test_suite(example_test_suite); + +In the above example the test suite, ``example_test_suite``, would run the test +cases ``example_test_foo``, ``example_test_bar``, and ``example_test_baz``, +each would have ``example_test_init`` called immediately before it and would +have ``example_test_exit`` called immediately after it. +``kunit_test_suite(example_test_suite)`` registers the test suite with the +KUnit test framework. + +.. note:: + A test case will only be run if it is associated with a test suite. + +For a more information on these types of things see the :doc:`api/test`. + +Isolating Behavior +================== + +The most important aspect of unit testing that other forms of testing do not +provide is the ability to limit the amount of code under test to a single unit. +In practice, this is only possible by being able to control what code gets run +when the unit under test calls a function and this is usually accomplished +through some sort of indirection where a function is exposed as part of an API +such that the definition of that function can be changed without affecting the +rest of the code base. In the kernel this primarily comes from two constructs, +classes, structs that contain function pointers that are provided by the +implementer, and architecture specific functions which have definitions selected +at compile time. + +Classes +------- + +Classes are not a construct that is built into the C programming language; +however, it is an easily derived concept. Accordingly, pretty much every project +that does not use a standardized object oriented library (like GNOME's GObject) +has their own slightly different way of doing object oriented programming; the +Linux kernel is no exception. + +The central concept in kernel object oriented programming is the class. In the +kernel, a *class* is a struct that contains function pointers. This creates a +contract between *implementers* and *users* since it forces them to use the +same function signature without having to call the function directly. In order +for it to truly be a class, the function pointers must specify that a pointer +to the class, known as a *class handle*, be one of the parameters; this makes +it possible for the member functions (also known as *methods*) to have access +to member variables (more commonly known as *fields*) allowing the same +implementation to have multiple *instances*. + +Typically a class can be *overridden* by *child classes* by embedding the +*parent class* in the child class. Then when a method provided by the child +class is called, the child implementation knows that the pointer passed to it is +of a parent contained within the child; because of this, the child can compute +the pointer to itself because the pointer to the parent is always a fixed offset +from the pointer to the child; this offset is the offset of the parent contained +in the child struct. For example: + +.. code-block:: c + + struct shape { + int (*area)(struct shape *this); + }; + + struct rectangle { + struct shape parent; + int length; + int width; + }; + + int rectangle_area(struct shape *this) + { + struct rectangle *self = container_of(this, struct shape, parent); + + return self->length * self->width; + }; + + void rectangle_new(struct rectangle *self, int length, int width) + { + self->parent.area = rectangle_area; + self->length = length; + self->width = width; + } + +In this example (as in most kernel code) the operation of computing the pointer +to the child from the pointer to the parent is done by ``container_of``. + +Faking Classes +~~~~~~~~~~~~~~ + +In order to unit test a piece of code that calls a method in a class, the +behavior of the method must be controllable, otherwise the test ceases to be a +unit test and becomes an integration test. + +A fake just provides an implementation of a piece of code that is different than +what runs in a production instance, but behaves identically from the standpoint +of the callers; this is usually done to replace a dependency that is hard to +deal with, or is slow. + +A good example for this might be implementing a fake EEPROM that just stores the +"contents" in an internal buffer. For example, let's assume we have a class that +represents an EEPROM: + +.. code-block:: c + + struct eeprom { + ssize_t (*read)(struct eeprom *this, size_t offset, char *buffer, size_t count); + ssize_t (*write)(struct eeprom *this, size_t offset, const char *buffer, size_t count); + }; + +And we want to test some code that buffers writes to the EEPROM: + +.. code-block:: c + + struct eeprom_buffer { + ssize_t (*write)(struct eeprom_buffer *this, const char *buffer, size_t count); + int flush(struct eeprom_buffer *this); + size_t flush_count; /* Flushes when buffer exceeds flush_count. */ + }; + + struct eeprom_buffer *new_eeprom_buffer(struct eeprom *eeprom); + void destroy_eeprom_buffer(struct eeprom *eeprom); + +We can easily test this code by *faking out* the underlying EEPROM: + +.. code-block:: c + + struct fake_eeprom { + struct eeprom parent; + char contents[FAKE_EEPROM_CONTENTS_SIZE]; + }; + + ssize_t fake_eeprom_read(struct eeprom *parent, size_t offset, char *buffer, size_t count) + { + struct fake_eeprom *this = container_of(parent, struct fake_eeprom, parent); + + count = min(count, FAKE_EEPROM_CONTENTS_SIZE - offset); + memcpy(buffer, this->contents + offset, count); + + return count; + } + + ssize_t fake_eeprom_write(struct eeprom *this, size_t offset, const char *buffer, size_t count) + { + struct fake_eeprom *this = container_of(parent, struct fake_eeprom, parent); + + count = min(count, FAKE_EEPROM_CONTENTS_SIZE - offset); + memcpy(this->contents + offset, buffer, count); + + return count; + } + + void fake_eeprom_init(struct fake_eeprom *this) + { + this->parent.read = fake_eeprom_read; + this->parent.write = fake_eeprom_write; + memset(this->contents, 0, FAKE_EEPROM_CONTENTS_SIZE); + } + +We can now use it to test ``struct eeprom_buffer``: + +.. code-block:: c + + struct eeprom_buffer_test { + struct fake_eeprom *fake_eeprom; + struct eeprom_buffer *eeprom_buffer; + }; + + static void eeprom_buffer_test_does_not_write_until_flush(struct kunit *test) + { + struct eeprom_buffer_test *ctx = test->priv; + struct eeprom_buffer *eeprom_buffer = ctx->eeprom_buffer; + struct fake_eeprom *fake_eeprom = ctx->fake_eeprom; + char buffer[] = {0xff}; + + eeprom_buffer->flush_count = SIZE_MAX; + + eeprom_buffer->write(eeprom_buffer, buffer, 1); + KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0); + + eeprom_buffer->write(eeprom_buffer, buffer, 1); + KUNIT_EXPECT_EQ(test, fake_eeprom->contents[1], 0); + + eeprom_buffer->flush(eeprom_buffer); + KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0xff); + KUNIT_EXPECT_EQ(test, fake_eeprom->contents[1], 0xff); + } + + static void eeprom_buffer_test_flushes_after_flush_count_met(struct kunit *test) + { + struct eeprom_buffer_test *ctx = test->priv; + struct eeprom_buffer *eeprom_buffer = ctx->eeprom_buffer; + struct fake_eeprom *fake_eeprom = ctx->fake_eeprom; + char buffer[] = {0xff}; + + eeprom_buffer->flush_count = 2; + + eeprom_buffer->write(eeprom_buffer, buffer, 1); + KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0); + + eeprom_buffer->write(eeprom_buffer, buffer, 1); + KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0xff); + KUNIT_EXPECT_EQ(test, fake_eeprom->contents[1], 0xff); + } + + static void eeprom_buffer_test_flushes_increments_of_flush_count(struct kunit *test) + { + struct eeprom_buffer_test *ctx = test->priv; + struct eeprom_buffer *eeprom_buffer = ctx->eeprom_buffer; + struct fake_eeprom *fake_eeprom = ctx->fake_eeprom; + char buffer[] = {0xff, 0xff}; + + eeprom_buffer->flush_count = 2; + + eeprom_buffer->write(eeprom_buffer, buffer, 1); + KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0); + + eeprom_buffer->write(eeprom_buffer, buffer, 2); + KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0xff); + KUNIT_EXPECT_EQ(test, fake_eeprom->contents[1], 0xff); + /* Should have only flushed the first two bytes. */ + KUNIT_EXPECT_EQ(test, fake_eeprom->contents[2], 0); + } + + static int eeprom_buffer_test_init(struct kunit *test) + { + struct eeprom_buffer_test *ctx; + + ctx = kunit_kzalloc(test, sizeof(*ctx), GFP_KERNEL); + KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ctx); + + ctx->fake_eeprom = kunit_kzalloc(test, sizeof(*ctx->fake_eeprom), GFP_KERNEL); + KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ctx->fake_eeprom); + fake_eeprom_init(ctx->fake_eeprom); + + ctx->eeprom_buffer = new_eeprom_buffer(&ctx->fake_eeprom->parent); + KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ctx->eeprom_buffer); + + test->priv = ctx; + + return 0; + } + + static void eeprom_buffer_test_exit(struct kunit *test) + { + struct eeprom_buffer_test *ctx = test->priv; + + destroy_eeprom_buffer(ctx->eeprom_buffer); + } + +.. _kunit-on-non-uml: + +KUnit on non-UML architectures +============================== + +By default KUnit uses UML as a way to provide dependencies for code under test. +Under most circumstances KUnit's usage of UML should be treated as an +implementation detail of how KUnit works under the hood. Nevertheless, there +are instances where being able to run architecture specific code, or test +against real hardware is desirable. For these reasons KUnit supports running on +other architectures. + +Running existing KUnit tests on non-UML architectures +----------------------------------------------------- + +There are some special considerations when running existing KUnit tests on +non-UML architectures: + +* Hardware may not be deterministic, so a test that always passes or fails + when run under UML may not always do so on real hardware. +* Hardware and VM environments may not be hermetic. KUnit tries its best to + provide a hermetic environment to run tests; however, it cannot manage state + that it doesn't know about outside of the kernel. Consequently, tests that + may be hermetic on UML may not be hermetic on other architectures. +* Some features and tooling may not be supported outside of UML. +* Hardware and VMs are slower than UML. + +None of these are reasons not to run your KUnit tests on real hardware; they are +only things to be aware of when doing so. + +The biggest impediment will likely be that certain KUnit features and +infrastructure may not support your target environment. For example, at this +time the KUnit Wrapper (``tools/testing/kunit/kunit.py``) does not work outside +of UML. Unfortunately, there is no way around this. Using UML (or even just a +particular architecture) allows us to make a lot of assumptions that make it +possible to do things which might otherwise be impossible. + +Nevertheless, all core KUnit framework features are fully supported on all +architectures, and using them is straightforward: all you need to do is to take +your kunitconfig, your Kconfig options for the tests you would like to run, and +merge them into whatever config your are using for your platform. That's it! + +For example, let's say you have the following kunitconfig: + +.. code-block:: none + + CONFIG_KUNIT=y + CONFIG_KUNIT_EXAMPLE_TEST=y + +If you wanted to run this test on an x86 VM, you might add the following config +options to your ``.config``: + +.. code-block:: none + + CONFIG_KUNIT=y + CONFIG_KUNIT_EXAMPLE_TEST=y + CONFIG_SERIAL_8250=y + CONFIG_SERIAL_8250_CONSOLE=y + +All these new options do is enable support for a common serial console needed +for logging. + +Next, you could build a kernel with these tests as follows: + + +.. code-block:: bash + + make ARCH=x86 olddefconfig + make ARCH=x86 + +Once you have built a kernel, you could run it on QEMU as follows: + +.. code-block:: bash + + qemu-system-x86_64 -enable-kvm \ + -m 1024 \ + -kernel arch/x86_64/boot/bzImage \ + -append 'console=ttyS0' \ + --nographic + +Interspersed in the kernel logs you might see the following: + +.. code-block:: none + + TAP version 14 + # Subtest: example + 1..1 + # example_simple_test: initializing + ok 1 - example_simple_test + ok 1 - example + +Congratulations, you just ran a KUnit test on the x86 architecture! + +Writing new tests for other architectures +----------------------------------------- + +The first thing you must do is ask yourself whether it is necessary to write a +KUnit test for a specific architecture, and then whether it is necessary to +write that test for a particular piece of hardware. In general, writing a test +that depends on having access to a particular piece of hardware or software (not +included in the Linux source repo) should be avoided at all costs. + +Even if you only ever plan on running your KUnit test on your hardware +configuration, other people may want to run your tests and may not have access +to your hardware. If you write your test to run on UML, then anyone can run your +tests without knowing anything about your particular setup, and you can still +run your tests on your hardware setup just by compiling for your architecture. + +.. important:: + Always prefer tests that run on UML to tests that only run under a particular + architecture, and always prefer tests that run under QEMU or another easy + (and monitarily free) to obtain software environment to a specific piece of + hardware. + +Nevertheless, there are still valid reasons to write an architecture or hardware +specific test: for example, you might want to test some code that really belongs +in ``arch/some-arch/*``. Even so, try your best to write the test so that it +does not depend on physical hardware: if some of your test cases don't need the +hardware, only require the hardware for tests that actually need it. + +Now that you have narrowed down exactly what bits are hardware specific, the +actual procedure for writing and running the tests is pretty much the same as +writing normal KUnit tests. One special caveat is that you have to reset +hardware state in between test cases; if this is not possible, you may only be +able to run one test case per invocation. + +.. TODO(brendanhiggins@google.com): Add an actual example of an architecture + dependent KUnit test. diff --git a/Documentation/devicetree/bindings/crypto/allwinner,sun8i-ss.yaml b/Documentation/devicetree/bindings/crypto/allwinner,sun8i-ss.yaml new file mode 100644 index 000000000000..8a29d36edf26 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/allwinner,sun8i-ss.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/crypto/allwinner,sun8i-ss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner Security System v2 driver + +maintainers: + - Corentin Labbe <corentin.labbe@gmail.com> + +properties: + compatible: + enum: + - allwinner,sun8i-a83t-crypto + - allwinner,sun9i-a80-crypto + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus clock + - description: Module clock + + clock-names: + items: + - const: bus + - const: mod + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/sun8i-a83t-ccu.h> + #include <dt-bindings/reset/sun8i-a83t-ccu.h> + + crypto: crypto@1c15000 { + compatible = "allwinner,sun8i-a83t-crypto"; + reg = <0x01c15000 0x1000>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + resets = <&ccu RST_BUS_SS>; + clocks = <&ccu CLK_BUS_SS>, <&ccu CLK_SS>; + clock-names = "bus", "mod"; + }; diff --git a/Documentation/devicetree/bindings/crypto/amlogic,gxl-crypto.yaml b/Documentation/devicetree/bindings/crypto/amlogic,gxl-crypto.yaml new file mode 100644 index 000000000000..5becc60a0e28 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/amlogic,gxl-crypto.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/crypto/amlogic,gxl-crypto.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic GXL Cryptographic Offloader + +maintainers: + - Corentin Labbe <clabbe@baylibre.com> + +properties: + compatible: + items: + - const: amlogic,gxl-crypto + + reg: + maxItems: 1 + + interrupts: + items: + - description: "Interrupt for flow 0" + - description: "Interrupt for flow 1" + + clocks: + maxItems: 1 + + clock-names: + const: blkmv + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/gxbb-clkc.h> + + crypto: crypto-engine@c883e000 { + compatible = "amlogic,gxl-crypto"; + reg = <0x0 0xc883e000 0x0 0x36>; + interrupts = <GIC_SPI 188 IRQ_TYPE_EDGE_RISING>, <GIC_SPI 189 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc CLKID_BLKMV>; + clock-names = "blkmv"; + }; diff --git a/Documentation/devicetree/bindings/mfd/da9062.txt b/Documentation/devicetree/bindings/mfd/da9062.txt index edca653a5777..bc4b59de6a55 100644 --- a/Documentation/devicetree/bindings/mfd/da9062.txt +++ b/Documentation/devicetree/bindings/mfd/da9062.txt @@ -66,6 +66,9 @@ Sub-nodes: details of individual regulator device can be found in: Documentation/devicetree/bindings/regulator/regulator.txt + regulator-initial-mode may be specified for buck regulators using mode values + from include/dt-bindings/regulator/dlg,da9063-regulator.h. + - rtc : This node defines settings required for the Real-Time Clock associated with the DA9062. There are currently no entries in this binding, however compatible = "dlg,da9062-rtc" should be added if a node is created. @@ -96,6 +99,7 @@ Example: regulator-max-microvolt = <1570000>; regulator-min-microamp = <500000>; regulator-max-microamp = <2000000>; + regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>; regulator-boot-on; }; DA9062_LDO1: ldo1 { diff --git a/Documentation/devicetree/bindings/mips/ralink.txt b/Documentation/devicetree/bindings/mips/ralink.txt index a16e8d7fe56c..8cc0ab41578c 100644 --- a/Documentation/devicetree/bindings/mips/ralink.txt +++ b/Documentation/devicetree/bindings/mips/ralink.txt @@ -16,3 +16,17 @@ value must be one of the following values: ralink,mt7620a-soc ralink,mt7620n-soc ralink,mt7628a-soc + ralink,mt7688a-soc + +2. Boards + +GARDENA smart Gateway (MT7688) + +This board is based on the MediaTek MT7688 and equipped with 128 MiB +of DDR and 8 MiB of flash (SPI NOR) and additional 128MiB SPI NAND +storage. + +------------------------------ +Required root node properties: +- compatible = "gardena,smart-gateway-mt7688", "ralink,mt7688a-soc", + "ralink,mt7628a-soc"; diff --git a/Documentation/devicetree/bindings/mtd/cadence-nand-controller.txt b/Documentation/devicetree/bindings/mtd/cadence-nand-controller.txt new file mode 100644 index 000000000000..f3893c4d3c6a --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/cadence-nand-controller.txt @@ -0,0 +1,53 @@ +* Cadence NAND controller + +Required properties: + - compatible : "cdns,hp-nfc" + - reg : Contains two entries, each of which is a tuple consisting of a + physical address and length. The first entry is the address and + length of the controller register set. The second entry is the + address and length of the Slave DMA data port. + - reg-names: should contain "reg" and "sdma" + - #address-cells: should be 1. The cell encodes the chip select connection. + - #size-cells : should be 0. + - interrupts : The interrupt number. + - clocks: phandle of the controller core clock (nf_clk). + +Optional properties: + - dmas: shall reference DMA channel associated to the NAND controller + - cdns,board-delay-ps : Estimated Board delay. The value includes the total + round trip delay for the signals and is used for deciding on values + associated with data read capture. The example formula for SDR mode is + the following: + board delay = RE#PAD delay + PCB trace to device + PCB trace from device + + DQ PAD delay + +Child nodes represent the available NAND chips. + +Required properties of NAND chips: + - reg: shall contain the native Chip Select ids from 0 to max supported by + the cadence nand flash controller + +See Documentation/devicetree/bindings/mtd/nand.txt for more details on +generic bindings. + +Example: + +nand_controller: nand-controller@60000000 { + compatible = "cdns,hp-nfc"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x60000000 0x10000>, <0x80000000 0x10000>; + reg-names = "reg", "sdma"; + clocks = <&nf_clk>; + cdns,board-delay-ps = <4830>; + interrupts = <2 0>; + nand@0 { + reg = <0>; + label = "nand-1"; + }; + nand@1 { + reg = <1>; + label = "nand-2"; + }; + +}; diff --git a/Documentation/devicetree/bindings/mtd/intel,ixp4xx-flash.txt b/Documentation/devicetree/bindings/mtd/intel,ixp4xx-flash.txt new file mode 100644 index 000000000000..4bdcb92ae381 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/intel,ixp4xx-flash.txt @@ -0,0 +1,22 @@ +Flash device on Intel IXP4xx SoC + +This flash is regular CFI compatible (Intel or AMD extended) flash chips with +specific big-endian or mixed-endian memory access pattern. + +Required properties: +- compatible : must be "intel,ixp4xx-flash", "cfi-flash"; +- reg : memory address for the flash chip +- bank-width : width in bytes of flash interface, should be <2> + +For the rest of the properties, see mtd-physmap.txt. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + +flash@50000000 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + reg = <0x50000000 0x01000000>; + bank-width = <2>; +}; diff --git a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt index b7336b9d6a3c..48a7f916c5e4 100644 --- a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt @@ -44,6 +44,12 @@ Optional properties: Admission Control Block supports reporting the number of packets in-flight in a switch queue +- resets: a single phandle and reset identifier pair. See + Documentation/devicetree/binding/reset/reset.txt for details. + +- reset-names: If the "reset" property is specified, this property should have + the value "switch" to denote the switch reset line. + Port subnodes: Optional properties: diff --git a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt index 3956af1d30f3..33a0d67e4ce5 100644 --- a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt +++ b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt @@ -2,7 +2,7 @@ Required properties: - compatible: should contain one of "brcm,genet-v1", "brcm,genet-v2", - "brcm,genet-v3", "brcm,genet-v4", "brcm,genet-v5". + "brcm,genet-v3", "brcm,genet-v4", "brcm,genet-v5", "brcm,bcm2711-genet-v5". - reg: address and length of the register set for the device - interrupts and/or interrupts-extended: must be two cells, the first cell is the general purpose interrupt line, while the second cell is the diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt index 4fa00e2eafcf..f16b99571af1 100644 --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt @@ -14,6 +14,8 @@ Required properties: * "brcm,bcm4330-bt" * "brcm,bcm43438-bt" * "brcm,bcm4345c5" + * "brcm,bcm43540-bt" + * "brcm,bcm4335a0" Optional properties: diff --git a/Documentation/devicetree/bindings/net/ethernet-controller.yaml b/Documentation/devicetree/bindings/net/ethernet-controller.yaml index 0e7c31794ae6..ac471b60ed6a 100644 --- a/Documentation/devicetree/bindings/net/ethernet-controller.yaml +++ b/Documentation/devicetree/bindings/net/ethernet-controller.yaml @@ -121,6 +121,11 @@ properties: and is useful for determining certain configuration settings such as flow control thresholds. + sfp: + $ref: /schemas/types.yaml#definitions/phandle + description: + Specifies a reference to a node representing a SFP cage. + tx-fifo-depth: $ref: /schemas/types.yaml#definitions/uint32 description: diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml index f70f18ff821f..8927941c74bb 100644 --- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml +++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml @@ -153,6 +153,11 @@ properties: Delay after the reset was deasserted in microseconds. If this property is missing the delay will be skipped. + sfp: + $ref: /schemas/types.yaml#definitions/phandle + description: + Specifies a reference to a node representing a SFP cage. + required: - reg diff --git a/Documentation/devicetree/bindings/net/ftgmac100.txt b/Documentation/devicetree/bindings/net/ftgmac100.txt index 72e7aaf7242e..f878c1103463 100644 --- a/Documentation/devicetree/bindings/net/ftgmac100.txt +++ b/Documentation/devicetree/bindings/net/ftgmac100.txt @@ -9,6 +9,7 @@ Required properties: - "aspeed,ast2400-mac" - "aspeed,ast2500-mac" + - "aspeed,ast2600-mac" - reg: Address and length of the register set for the device - interrupts: Should contain ethernet controller interrupt @@ -23,6 +24,13 @@ Optional properties: - no-hw-checksum: Used to disable HW checksum support. Here for backward compatibility as the driver now should have correct defaults based on the SoC. +- clocks: In accordance with the generic clock bindings. Must describe the MAC + IP clock, and optionally an RMII RCLK gate for the AST2500/AST2600. The + required MAC clock must be the first cell. +- clock-names: + + - "MACCLK": The MAC IP clock + - "RCLK": Clock gate for the RMII RCLK Example: diff --git a/Documentation/devicetree/bindings/net/lpc-eth.txt b/Documentation/devicetree/bindings/net/lpc-eth.txt index b92e927808b6..cfe0e5991d46 100644 --- a/Documentation/devicetree/bindings/net/lpc-eth.txt +++ b/Documentation/devicetree/bindings/net/lpc-eth.txt @@ -10,6 +10,11 @@ Optional properties: absent, "rmii" is assumed. - use-iram: Use LPC32xx internal SRAM (IRAM) for DMA buffering +Optional subnodes: +- mdio : specifies the mdio bus, used as a container for phy nodes according to + phy.txt in the same directory + + Example: mac: ethernet@31060000 { diff --git a/Documentation/devicetree/bindings/net/nfc/pn532.txt b/Documentation/devicetree/bindings/net/nfc/pn532.txt new file mode 100644 index 000000000000..a5507dc499bc --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/pn532.txt @@ -0,0 +1,46 @@ +* NXP Semiconductors PN532 NFC Controller + +Required properties: +- compatible: Should be + - "nxp,pn532" Place a node with this inside the devicetree node of the bus + where the NFC chip is connected to. + Currently the kernel has phy bindings for uart and i2c. + - "nxp,pn532-i2c" (DEPRECATED) only works for the i2c binding. + - "nxp,pn533-i2c" (DEPRECATED) only works for the i2c binding. + +Required properties if connected on i2c: +- clock-frequency: I²C work frequency. +- reg: for the I²C bus address. This is fixed at 0x24 for the PN532. +- interrupts: GPIO interrupt to which the chip is connected + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with PN532 on I2C2): + +&i2c2 { + + + pn532: nfc@24 { + + compatible = "nxp,pn532"; + + reg = <0x24>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; + + }; +}; + +Example (for PN532 connected via uart): + +uart4: serial@49042000 { + compatible = "ti,omap3-uart"; + + pn532: nfc { + compatible = "nxp,pn532"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt b/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt deleted file mode 100644 index 2efe3886b95b..000000000000 --- a/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt +++ /dev/null @@ -1,29 +0,0 @@ -* NXP Semiconductors PN532 NFC Controller - -Required properties: -- compatible: Should be "nxp,pn532-i2c" or "nxp,pn533-i2c". -- clock-frequency: I²C work frequency. -- reg: address on the bus -- interrupts: GPIO interrupt to which the chip is connected - -Optional SoC Specific Properties: -- pinctrl-names: Contains only one value - "default". -- pintctrl-0: Specifies the pin control groups used for this controller. - -Example (for ARM-based BeagleBone with PN532 on I2C2): - -&i2c2 { - - - pn532: pn532@24 { - - compatible = "nxp,pn532-i2c"; - - reg = <0x24>; - clock-frequency = <400000>; - - interrupt-parent = <&gpio1>; - interrupts = <17 IRQ_TYPE_EDGE_FALLING>; - - }; -}; diff --git a/Documentation/devicetree/bindings/net/qca,ar803x.yaml b/Documentation/devicetree/bindings/net/qca,ar803x.yaml new file mode 100644 index 000000000000..5a6c9d20c0ba --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca,ar803x.yaml @@ -0,0 +1,111 @@ +# SPDX-License-Identifier: GPL-2.0+ +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qca,ar803x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Atheros AR803x PHY + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + - Florian Fainelli <f.fainelli@gmail.com> + - Heiner Kallweit <hkallweit1@gmail.com> + +description: | + Bindings for Qualcomm Atheros AR803x PHYs + +allOf: + - $ref: ethernet-phy.yaml# + +properties: + qca,clk-out-frequency: + description: Clock output frequency in Hertz. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 25000000, 50000000, 62500000, 125000000 ] + + qca,clk-out-strength: + description: Clock output driver strength. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1, 2 ] + + qca,keep-pll-enabled: + description: | + If set, keep the PLL enabled even if there is no link. Useful if you + want to use the clock output without an ethernet link. + + Only supported on the AR8031. + type: boolean + + vddio-supply: + description: | + RGMII I/O voltage regulator (see regulator/regulator.yaml). + + The PHY supports RGMII I/O voltages of 1.5V, 1.8V and 2.5V. You can + either connect this to the vddio-regulator (1.5V / 1.8V) or the + vddh-regulator (2.5V). + + Only supported on the AR8031. + + vddio-regulator: + type: object + description: + Initial data for the VDDIO regulator. Set this to 1.5V or 1.8V. + allOf: + - $ref: /schemas/regulator/regulator.yaml + + vddh-regulator: + type: object + description: + Dummy subnode to model the external connection of the PHY VDDH + regulator to VDDIO. + allOf: + - $ref: /schemas/regulator/regulator.yaml + + +examples: + - | + #include <dt-bindings/net/qca-ar803x.h> + + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + phy-mode = "rgmii-id"; + + ethernet-phy@0 { + reg = <0>; + + qca,clk-out-frequency = <125000000>; + qca,clk-out-strength = <AR803X_STRENGTH_FULL>; + + vddio-supply = <&vddio>; + + vddio: vddio-regulator { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + }; + - | + #include <dt-bindings/net/qca-ar803x.h> + + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + phy-mode = "rgmii-id"; + + ethernet-phy@0 { + reg = <0>; + + qca,clk-out-frequency = <50000000>; + qca,keep-pll-enabled; + + vddio-supply = <&vddh>; + + vddh: vddh-regulator { + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/renesas,ether.yaml b/Documentation/devicetree/bindings/net/renesas,ether.yaml new file mode 100644 index 000000000000..7f84df9790e2 --- /dev/null +++ b/Documentation/devicetree/bindings/net/renesas,ether.yaml @@ -0,0 +1,114 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/renesas,ether.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas Electronics SH EtherMAC + +allOf: + - $ref: ethernet-controller.yaml# + +maintainers: + - Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,gether-r8a7740 # device is a part of R8A7740 SoC + - renesas,gether-r8a77980 # device is a part of R8A77980 SoC + - renesas,ether-r7s72100 # device is a part of R7S72100 SoC + - renesas,ether-r7s9210 # device is a part of R7S9210 SoC + - items: + - enum: + - renesas,ether-r8a7778 # device is a part of R8A7778 SoC + - renesas,ether-r8a7779 # device is a part of R8A7779 SoC + - enum: + - renesas,rcar-gen1-ether # a generic R-Car Gen1 device + - items: + - enum: + - renesas,ether-r8a7745 # device is a part of R8A7745 SoC + - renesas,ether-r8a7743 # device is a part of R8A7743 SoC + - renesas,ether-r8a7790 # device is a part of R8A7790 SoC + - renesas,ether-r8a7791 # device is a part of R8A7791 SoC + - renesas,ether-r8a7793 # device is a part of R8A7793 SoC + - renesas,ether-r8a7794 # device is a part of R8A7794 SoC + - enum: + - renesas,rcar-gen2-ether # a generic R-Car Gen2 or RZ/G1 device + + reg: + items: + - description: E-DMAC/feLic registers + - description: TSU registers + minItems: 1 + + interrupts: + maxItems: 1 + + '#address-cells': + description: number of address cells for the MDIO bus + const: 1 + + '#size-cells': + description: number of size cells on the MDIO bus + const: 0 + + clocks: + maxItems: 1 + + pinctrl-0: true + + pinctrl-names: true + + renesas,no-ether-link: + type: boolean + description: + specify when a board does not provide a proper Ether LINK signal + + renesas,ether-link-active-low: + type: boolean + description: + specify when the Ether LINK signal is active-low instead of normal + active-high + +required: + - compatible + - reg + - interrupts + - phy-mode + - phy-handle + - '#address-cells' + - '#size-cells' + - clocks + - pinctrl-0 + +examples: + # Lager board + - | + #include <dt-bindings/clock/r8a7790-clock.h> + #include <dt-bindings/interrupt-controller/irq.h> + + ethernet@ee700000 { + compatible = "renesas,ether-r8a7790", "renesas,rcar-gen2-ether"; + reg = <0 0xee700000 0 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7790_CLK_ETHER>; + phy-mode = "rmii"; + phy-handle = <&phy1>; + pinctrl-0 = <ðer_pins>; + pinctrl-names = "default"; + renesas,ether-link-active-low; + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&irqc0>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&phy1_pins>; + pinctrl-names = "default"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt deleted file mode 100644 index abc36274227c..000000000000 --- a/Documentation/devicetree/bindings/net/sh_eth.txt +++ /dev/null @@ -1,69 +0,0 @@ -* Renesas Electronics SH EtherMAC - -This file provides information on what the device node for the SH EtherMAC -interface contains. - -Required properties: -- compatible: Must contain one or more of the following: - "renesas,gether-r8a7740" if the device is a part of R8A7740 SoC. - "renesas,ether-r8a7743" if the device is a part of R8A7743 SoC. - "renesas,ether-r8a7745" if the device is a part of R8A7745 SoC. - "renesas,ether-r8a7778" if the device is a part of R8A7778 SoC. - "renesas,ether-r8a7779" if the device is a part of R8A7779 SoC. - "renesas,ether-r8a7790" if the device is a part of R8A7790 SoC. - "renesas,ether-r8a7791" if the device is a part of R8A7791 SoC. - "renesas,ether-r8a7793" if the device is a part of R8A7793 SoC. - "renesas,ether-r8a7794" if the device is a part of R8A7794 SoC. - "renesas,gether-r8a77980" if the device is a part of R8A77980 SoC. - "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC. - "renesas,ether-r7s9210" if the device is a part of R7S9210 SoC. - "renesas,rcar-gen1-ether" for a generic R-Car Gen1 device. - "renesas,rcar-gen2-ether" for a generic R-Car Gen2 or RZ/G1 - device. - - When compatible with the generic version, nodes must list - the SoC-specific version corresponding to the platform - first followed by the generic version. - -- reg: offset and length of (1) the E-DMAC/feLic register block (required), - (2) the TSU register block (optional). -- interrupts: interrupt specifier for the sole interrupt. -- phy-mode: see ethernet.txt file in the same directory. -- phy-handle: see ethernet.txt file in the same directory. -- #address-cells: number of address cells for the MDIO bus, must be equal to 1. -- #size-cells: number of size cells on the MDIO bus, must be equal to 0. -- clocks: clock phandle and specifier pair. -- pinctrl-0: phandle, referring to a default pin configuration node. - -Optional properties: -- pinctrl-names: pin configuration state name ("default"). -- renesas,no-ether-link: boolean, specify when a board does not provide a proper - Ether LINK signal. -- renesas,ether-link-active-low: boolean, specify when the Ether LINK signal is - active-low instead of normal active-high. - -Example (Lager board): - - ethernet@ee700000 { - compatible = "renesas,ether-r8a7790", - "renesas,rcar-gen2-ether"; - reg = <0 0xee700000 0 0x400>; - interrupt-parent = <&gic>; - interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp8_clks R8A7790_CLK_ETHER>; - phy-mode = "rmii"; - phy-handle = <&phy1>; - pinctrl-0 = <ðer_pins>; - pinctrl-names = "default"; - renesas,ether-link-active-low; - #address-cells = <1>; - #size-cells = <0>; - - phy1: ethernet-phy@1 { - reg = <1>; - interrupt-parent = <&irqc0>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - pinctrl-0 = <&phy1_pins>; - pinctrl-names = "default"; - }; - }; diff --git a/Documentation/devicetree/bindings/net/ti,cpsw-switch.yaml b/Documentation/devicetree/bindings/net/ti,cpsw-switch.yaml new file mode 100644 index 000000000000..81ae8cafabc1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,cpsw-switch.yaml @@ -0,0 +1,240 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/ti,cpsw-switch.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI SoC Ethernet Switch Controller (CPSW) Device Tree Bindings + +maintainers: + - Grygorii Strashko <grygorii.strashko@ti.com> + - Sekhar Nori <nsekhar@ti.com> + +description: + The 3-port switch gigabit ethernet subsystem provides ethernet packet + communication and can be configured as an ethernet switch. It provides the + gigabit media independent interface (GMII),reduced gigabit media + independent interface (RGMII), reduced media independent interface (RMII), + the management data input output (MDIO) for physical layer device (PHY) + management. + +properties: + compatible: + oneOf: + - const: ti,cpsw-switch + - items: + - const: ti,am335x-cpsw-switch + - const: ti,cpsw-switch + - items: + - const: ti,am4372-cpsw-switch + - const: ti,cpsw-switch + - items: + - const: ti,dra7-cpsw-switch + - const: ti,cpsw-switch + + reg: + maxItems: 1 + description: + The physical base address and size of full the CPSW module IO range + + ranges: true + + clocks: + maxItems: 1 + description: CPSW functional clock + + clock-names: + maxItems: 1 + items: + - const: fck + + interrupts: + items: + - description: RX_THRESH interrupt + - description: RX interrupt + - description: TX interrupt + - description: MISC interrupt + + interrupt-names: + items: + - const: "rx_thresh" + - const: "rx" + - const: "tx" + - const: "misc" + + pinctrl-names: true + + syscon: + $ref: /schemas/types.yaml#definitions/phandle + description: + Phandle to the system control device node which provides access to + efuse IO range with MAC addresses + + + ethernet-ports: + type: object + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + patternProperties: + "^port@[0-9]+$": + type: object + minItems: 1 + maxItems: 2 + description: CPSW external ports + + allOf: + - $ref: ethernet-controller.yaml# + + properties: + reg: + maxItems: 1 + enum: [1, 2] + description: CPSW port number + + phys: + $ref: /schemas/types.yaml#definitions/phandle-array + maxItems: 1 + description: phandle on phy-gmii-sel PHY + + label: + $ref: /schemas/types.yaml#/definitions/string-array + maxItems: 1 + description: label associated with this port + + ti,dual-emac-pvid: + $ref: /schemas/types.yaml#/definitions/uint32 + maxItems: 1 + minimum: 1 + maximum: 1024 + description: + Specifies default PORT VID to be used to segregate + ports. Default value - CPSW port number. + + required: + - reg + - phys + + mdio: + type: object + allOf: + - $ref: "ti,davinci-mdio.yaml#" + description: + CPSW MDIO bus. + + cpts: + type: object + description: + The Common Platform Time Sync (CPTS) module + + properties: + clocks: + maxItems: 1 + description: CPTS reference clock + + clock-names: + maxItems: 1 + items: + - const: cpts + + cpts_clock_mult: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Numerator to convert input clock ticks into ns + + cpts_clock_shift: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Denominator to convert input clock ticks into ns. + Mult and shift will be calculated basing on CPTS rftclk frequency if + both cpts_clock_shift and cpts_clock_mult properties are not provided. + + required: + - clocks + - clock-names + +required: + - compatible + - reg + - ranges + - clocks + - clock-names + - interrupts + - interrupt-names + - '#address-cells' + - '#size-cells' + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/dra7.h> + + mac_sw: switch@0 { + compatible = "ti,dra7-cpsw-switch","ti,cpsw-switch"; + reg = <0x0 0x4000>; + ranges = <0 0 0x4000>; + clocks = <&gmac_main_clk>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + syscon = <&scm_conf>; + inctrl-names = "default", "sleep"; + + interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "rx_thresh", "rx", "tx", "misc"; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + cpsw_port1: port@1 { + reg = <1>; + label = "port1"; + mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 1>; + phy-handle = <ðphy0_sw>; + phy-mode = "rgmii"; + ti,dual_emac_pvid = <1>; + }; + + cpsw_port2: port@2 { + reg = <2>; + label = "wan"; + mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 2>; + phy-handle = <ðphy1_sw>; + phy-mode = "rgmii"; + ti,dual_emac_pvid = <2>; + }; + }; + + davinci_mdio_sw: mdio@1000 { + compatible = "ti,cpsw-mdio","ti,davinci_mdio"; + reg = <0x1000 0x100>; + clocks = <&gmac_clkctrl DRA7_GMAC_GMAC_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <0>; + bus_freq = <1000000>; + + ethphy0_sw: ethernet-phy@0 { + reg = <0>; + }; + + ethphy1_sw: ethernet-phy@1 { + reg = <1>; + }; + }; + + cpts { + clocks = <&gmac_clkctrl DRA7_GMAC_GMAC_CLKCTRL 25>; + clock-names = "cpts"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ti,dp83869.yaml b/Documentation/devicetree/bindings/net/ti,dp83869.yaml new file mode 100644 index 000000000000..6fe3e451da8a --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,dp83869.yaml @@ -0,0 +1,84 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (C) 2019 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/net/ti,dp83869.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI DP83869 ethernet PHY + +allOf: + - $ref: "ethernet-controller.yaml#" + +maintainers: + - Dan Murphy <dmurphy@ti.com> + +description: | + The DP83869HM device is a robust, fully-featured Gigabit (PHY) transceiver + with integrated PMD sublayers that supports 10BASE-Te, 100BASE-TX and + 1000BASE-T Ethernet protocols. The DP83869 also supports 1000BASE-X and + 100BASE-FX Fiber protocols. + This device interfaces to the MAC layer through Reduced GMII (RGMII) and + SGMII The DP83869HM supports Media Conversion in Managed mode. In this mode, + the DP83869HM can run 1000BASE-X-to-1000BASE-T and 100BASE-FX-to-100BASE-TX + conversions. The DP83869HM can also support Bridge Conversion from RGMII to + SGMII and SGMII to RGMII. + + Specifications about the charger can be found at: + http://www.ti.com/lit/ds/symlink/dp83869hm.pdf + +properties: + reg: + maxItems: 1 + + ti,min-output-impedance: + type: boolean + description: | + MAC Interface Impedance control to set the programmable output impedance + to a minimum value (35 ohms). + + ti,max-output-impedance: + type: boolean + description: | + MAC Interface Impedance control to set the programmable output impedance + to a maximum value (70 ohms). + + tx-fifo-depth: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Transmitt FIFO depth see dt-bindings/net/ti-dp83869.h for values + + rx-fifo-depth: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Receive FIFO depth see dt-bindings/net/ti-dp83869.h for values + + ti,clk-output-sel: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Muxing option for CLK_OUT pin see dt-bindings/net/ti-dp83869.h for values. + + ti,op-mode: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Operational mode for the PHY. If this is not set then the operational + mode is set by the straps. see dt-bindings/net/ti-dp83869.h for values + +required: + - reg + +examples: + - | + #include <dt-bindings/net/ti-dp83869.h> + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + ethphy0: ethernet-phy@0 { + reg = <0>; + tx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>; + rx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>; + ti,max-output-impedance = "true"; + ti,clk-output-sel = <DP83869_CLK_O_SEL_CHN_A_RCLK>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index ae661e65354e..017128394a3e 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -81,6 +81,12 @@ Optional properties: Definition: Name of external front end module used. Some valid FEM names for example: "microsemi-lx5586", "sky85703-11" and "sky85803" etc. +- qcom,snoc-host-cap-8bit-quirk: + Usage: Optional + Value type: <empty> + Definition: Quirk specifying that the firmware expects the 8bit version + of the host capability QMI request +- qcom,xo-cal-data: xo cal offset to be configured in xo trim register. Example (to supply PCI based wifi block details): diff --git a/Documentation/devicetree/bindings/perf/arm-ccn.txt b/Documentation/devicetree/bindings/perf/arm-ccn.txt index 43b5a71a5a9d..1c53b5aa3317 100644 --- a/Documentation/devicetree/bindings/perf/arm-ccn.txt +++ b/Documentation/devicetree/bindings/perf/arm-ccn.txt @@ -6,6 +6,7 @@ Required properties: "arm,ccn-502" "arm,ccn-504" "arm,ccn-508" + "arm,ccn-512" - reg: (standard registers property) physical address and size (16MB) of the configuration registers block diff --git a/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt b/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt index d77e3f26f9e6..7822a806ea0a 100644 --- a/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt +++ b/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt @@ -5,6 +5,7 @@ Required properties: - compatible: should be one of: "fsl,imx8-ddr-pmu" "fsl,imx8m-ddr-pmu" + "fsl,imx8mp-ddr-pmu" - reg: physical address and size diff --git a/Documentation/devicetree/bindings/ptp/ptp-idtcm.yaml b/Documentation/devicetree/bindings/ptp/ptp-idtcm.yaml new file mode 100644 index 000000000000..9e21b83d717e --- /dev/null +++ b/Documentation/devicetree/bindings/ptp/ptp-idtcm.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ptp/ptp-idtcm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: IDT ClockMatrix (TM) PTP Clock Device Tree Bindings + +maintainers: + - Vincent Cheng <vincent.cheng.xh@renesas.com> + +properties: + compatible: + enum: + # For System Synchronizer + - idt,8a34000 + - idt,8a34001 + - idt,8a34002 + - idt,8a34003 + - idt,8a34004 + - idt,8a34005 + - idt,8a34006 + - idt,8a34007 + - idt,8a34008 + - idt,8a34009 + # For Port Synchronizer + - idt,8a34010 + - idt,8a34011 + - idt,8a34012 + - idt,8a34013 + - idt,8a34014 + - idt,8a34015 + - idt,8a34016 + - idt,8a34017 + - idt,8a34018 + - idt,8a34019 + # For Universal Frequency Translator (UFT) + - idt,8a34040 + - idt,8a34041 + - idt,8a34042 + - idt,8a34043 + - idt,8a34044 + - idt,8a34045 + - idt,8a34046 + - idt,8a34047 + - idt,8a34048 + - idt,8a34049 + + reg: + maxItems: 1 + description: + I2C slave address of the device. + +required: + - compatible + - reg + +examples: + - | + i2c@1 { + compatible = "abc,acme-1234"; + reg = <0x01 0x400>; + #address-cells = <1>; + #size-cells = <0>; + phc@5b { + compatible = "idt,8a34000"; + reg = <0x5b>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml index f32416968197..59b4b73d4051 100644 --- a/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml @@ -50,6 +50,10 @@ properties: description: startup time in microseconds $ref: /schemas/types.yaml#/definitions/uint32 + off-on-delay-us: + description: off delay time in microseconds + $ref: /schemas/types.yaml#/definitions/uint32 + enable-active-high: description: Polarity of GPIO is Active high. If this property is missing, diff --git a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.txt index bab9f71140b8..97c3e0b7611c 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.txt @@ -28,6 +28,8 @@ Supported regulator node names: PM8150L: smps1 - smps8, ldo1 - ldo11, bob, flash, rgb PM8998: smps1 - smps13, ldo1 - ldo28, lvs1 - lvs2 PMI8998: bob + PM6150: smps1 - smps5, ldo1 - ldo19 + PM6150L: smps1 - smps8, ldo1 - ldo11, bob ======================== First Level Nodes - PMIC @@ -43,6 +45,8 @@ First Level Nodes - PMIC "qcom,pm8150l-rpmh-regulators" "qcom,pm8998-rpmh-regulators" "qcom,pmi8998-rpmh-regulators" + "qcom,pm6150-rpmh-regulators" + "qcom,pm6150l-rpmh-regulators" - qcom,pmic-id Usage: required diff --git a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt index 45025b5b67f6..d126df043403 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt @@ -22,6 +22,7 @@ Regulator nodes are identified by their compatible: "qcom,rpm-pm8841-regulators" "qcom,rpm-pm8916-regulators" "qcom,rpm-pm8941-regulators" + "qcom,rpm-pm8950-regulators" "qcom,rpm-pm8994-regulators" "qcom,rpm-pm8998-regulators" "qcom,rpm-pma8084-regulators" @@ -57,6 +58,26 @@ Regulator nodes are identified by their compatible: - vdd_s1-supply: - vdd_s2-supply: - vdd_s3-supply: +- vdd_s4-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_l1_l19-supply: +- vdd_l2_l23-supply: +- vdd_l3-supply: +- vdd_l4_l5_l6_l7_l16-supply: +- vdd_l8_l11_l12_l17_l22-supply: +- vdd_l9_l10_l13_l14_l15_l18-supply: +- vdd_l20-supply: +- vdd_l21-supply: + Usage: optional (pm8950 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: - vdd_l1_l3-supply: - vdd_l2_lvs1_2_3-supply: - vdd_l4_l11-supply: diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 430b8622bda1..f5cdac8b2847 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -4,10 +4,12 @@ Qualcomm SPMI Regulators Usage: required Value type: <string> Definition: must be one of: + "qcom,pm8004-regulators" "qcom,pm8005-regulators" "qcom,pm8841-regulators" "qcom,pm8916-regulators" "qcom,pm8941-regulators" + "qcom,pm8950-regulators" "qcom,pm8994-regulators" "qcom,pmi8994-regulators" "qcom,pms405-regulators" @@ -76,6 +78,26 @@ Qualcomm SPMI Regulators - vdd_s2-supply: - vdd_s3-supply: - vdd_s4-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_l1_l19-supply: +- vdd_l2_l23-supply: +- vdd_l3-supply: +- vdd_l4_l5_l6_l7_l16-supply: +- vdd_l8_l11_l12_l17_l22-supply: +- vdd_l9_l10_l13_l14_l15_l18-supply: +- vdd_l20-supply: +- vdd_l21-supply: + Usage: optional (pm8950 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: - vdd_s5-supply: - vdd_s6-supply: - vdd_s7-supply: @@ -140,6 +162,9 @@ sub-node is identified using the node's name, with valid values listed for each of the PMICs below. pm8005: + s2, s5 + +pm8005: s1, s2, s3, s4 pm8841: diff --git a/Documentation/devicetree/bindings/regulator/regulator.yaml b/Documentation/devicetree/bindings/regulator/regulator.yaml index 02c3043ce419..92ff2e8ad572 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.yaml +++ b/Documentation/devicetree/bindings/regulator/regulator.yaml @@ -38,7 +38,12 @@ properties: type: boolean regulator-boot-on: - description: bootloader/firmware enabled regulator + description: bootloader/firmware enabled regulator. + It's expected that this regulator was left on by the bootloader. + If the bootloader didn't leave it on then OS should turn it on + at boot but shouldn't prevent it from being turned off later. + This property is intended to only be used for regulators where + software cannot read the state of the regulator. type: boolean regulator-allow-bypass: diff --git a/Documentation/devicetree/bindings/rng/atmel-trng.txt b/Documentation/devicetree/bindings/rng/atmel-trng.txt index 4ac5aaa2d024..3900ee4f3532 100644 --- a/Documentation/devicetree/bindings/rng/atmel-trng.txt +++ b/Documentation/devicetree/bindings/rng/atmel-trng.txt @@ -1,7 +1,7 @@ Atmel TRNG (True Random Number Generator) block Required properties: -- compatible : Should be "atmel,at91sam9g45-trng" +- compatible : Should be "atmel,at91sam9g45-trng" or "microchip,sam9x60-trng" - reg : Offset and length of the register set of this block - interrupts : the interrupt number for the TRNG block - clocks: should contain the TRNG clk source diff --git a/Documentation/devicetree/bindings/rng/nuvoton,npcm-rng.txt b/Documentation/devicetree/bindings/rng/nuvoton,npcm-rng.txt new file mode 100644 index 000000000000..65c04172fc8c --- /dev/null +++ b/Documentation/devicetree/bindings/rng/nuvoton,npcm-rng.txt @@ -0,0 +1,12 @@ +NPCM SoC Random Number Generator + +Required properties: +- compatible : "nuvoton,npcm750-rng" for the NPCM7XX BMC. +- reg : Specifies physical base address and size of the registers. + +Example: + +rng: rng@f000b000 { + compatible = "nuvoton,npcm750-rng"; + reg = <0xf000b000 0x8>; +}; diff --git a/Documentation/devicetree/bindings/rng/omap3_rom_rng.txt b/Documentation/devicetree/bindings/rng/omap3_rom_rng.txt new file mode 100644 index 000000000000..f315c9723bd2 --- /dev/null +++ b/Documentation/devicetree/bindings/rng/omap3_rom_rng.txt @@ -0,0 +1,27 @@ +OMAP ROM RNG driver binding + +Secure SoCs may provide RNG via secure ROM calls like Nokia N900 does. The +implementation can depend on the SoC secure ROM used. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "nokia,n900-rom-rng" + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to the the RNG interface clock + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: must be "ick" + +Example: + + rom_rng: rng { + compatible = "nokia,n900-rom-rng"; + clocks = <&rng_ick>; + clock-names = "ick"; + }; diff --git a/Documentation/devicetree/bindings/rng/samsung,exynos5250-trng.txt b/Documentation/devicetree/bindings/rng/samsung,exynos5250-trng.txt new file mode 100644 index 000000000000..5a613a4ec780 --- /dev/null +++ b/Documentation/devicetree/bindings/rng/samsung,exynos5250-trng.txt @@ -0,0 +1,17 @@ +Exynos True Random Number Generator + +Required properties: + +- compatible : Should be "samsung,exynos5250-trng". +- reg : Specifies base physical address and size of the registers map. +- clocks : Phandle to clock-controller plus clock-specifier pair. +- clock-names : "secss" as a clock name. + +Example: + + rng@10830600 { + compatible = "samsung,exynos5250-trng"; + reg = <0x10830600 0x100>; + clocks = <&clock CLK_SSS>; + clock-names = "secss"; + }; diff --git a/Documentation/devicetree/bindings/security/tpm/google,cr50.txt b/Documentation/devicetree/bindings/security/tpm/google,cr50.txt new file mode 100644 index 000000000000..cd69c2efdd37 --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/google,cr50.txt @@ -0,0 +1,19 @@ +* H1 Secure Microcontroller with Cr50 Firmware on SPI Bus. + +H1 Secure Microcontroller running Cr50 firmware provides several +functions, including TPM-like functionality. It communicates over +SPI using the FIFO protocol described in the PTP Spec, section 6. + +Required properties: +- compatible: Should be "google,cr50". +- spi-max-frequency: Maximum SPI frequency. + +Example: + +&spi0 { + tpm@0 { + compatible = "google,cr50"; + reg = <0>; + spi-max-frequency = <800000>; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/renesas,hspi.yaml b/Documentation/devicetree/bindings/spi/renesas,hspi.yaml new file mode 100644 index 000000000000..c429cf4bea5b --- /dev/null +++ b/Documentation/devicetree/bindings/spi/renesas,hspi.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/renesas,hspi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas HSPI + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +allOf: + - $ref: spi-controller.yaml# + +properties: + compatible: + items: + - enum: + - renesas,hspi-r8a7778 # R-Car M1A + - renesas,hspi-r8a7779 # R-Car H1 + - const: renesas,hspi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - '#address-cells' + - '#size-cells' + +examples: + - | + #include <dt-bindings/clock/r8a7778-clock.h> + #include <dt-bindings/interrupt-controller/irq.h> + + hspi0: spi@fffc7000 { + compatible = "renesas,hspi-r8a7778", "renesas,hspi"; + reg = <0xfffc7000 0x18>; + interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_HSPI>; + power-domains = <&cpg_clocks>; + #address-cells = <1>; + #size-cells = <0>; + }; + diff --git a/Documentation/devicetree/bindings/spi/renesas,rzn1-spi.txt b/Documentation/devicetree/bindings/spi/renesas,rzn1-spi.txt new file mode 100644 index 000000000000..fb1a6728638d --- /dev/null +++ b/Documentation/devicetree/bindings/spi/renesas,rzn1-spi.txt @@ -0,0 +1,11 @@ +Renesas RZ/N1 SPI Controller + +This controller is based on the Synopsys DW Synchronous Serial Interface and +inherits all properties defined in snps,dw-apb-ssi.txt except for the +compatible property. + +Required properties: +- compatible : The device specific string followed by the generic RZ/N1 string. + Therefore it must be one of: + "renesas,r9a06g032-spi", "renesas,rzn1-spi" + "renesas,r9a06g033-spi", "renesas,rzn1-spi" diff --git a/Documentation/devicetree/bindings/spi/renesas,sh-msiof.yaml b/Documentation/devicetree/bindings/spi/renesas,sh-msiof.yaml new file mode 100644 index 000000000000..b6c1dd2a9c5e --- /dev/null +++ b/Documentation/devicetree/bindings/spi/renesas,sh-msiof.yaml @@ -0,0 +1,159 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/renesas,sh-msiof.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas MSIOF SPI controller + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +allOf: + - $ref: spi-controller.yaml# + +properties: + compatible: + oneOf: + - items: + - const: renesas,msiof-sh73a0 # SH-Mobile AG5 + - const: renesas,sh-mobile-msiof # generic SH-Mobile compatible + # device + - items: + - enum: + - renesas,msiof-r8a7743 # RZ/G1M + - renesas,msiof-r8a7744 # RZ/G1N + - renesas,msiof-r8a7745 # RZ/G1E + - renesas,msiof-r8a77470 # RZ/G1C + - renesas,msiof-r8a7790 # R-Car H2 + - renesas,msiof-r8a7791 # R-Car M2-W + - renesas,msiof-r8a7792 # R-Car V2H + - renesas,msiof-r8a7793 # R-Car M2-N + - renesas,msiof-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-msiof # generic R-Car Gen2 and RZ/G1 + # compatible device + - items: + - enum: + - renesas,msiof-r8a774a1 # RZ/G2M + - renesas,msiof-r8a774b1 # RZ/G2N + - renesas,msiof-r8a774c0 # RZ/G2E + - renesas,msiof-r8a7795 # R-Car H3 + - renesas,msiof-r8a7796 # R-Car M3-W + - renesas,msiof-r8a77965 # R-Car M3-N + - renesas,msiof-r8a77970 # R-Car V3M + - renesas,msiof-r8a77980 # R-Car V3H + - renesas,msiof-r8a77990 # R-Car E3 + - renesas,msiof-r8a77995 # R-Car D3 + - const: renesas,rcar-gen3-msiof # generic R-Car Gen3 and RZ/G2 + # compatible device + - items: + - const: renesas,sh-msiof # deprecated + + reg: + minItems: 1 + maxItems: 2 + oneOf: + - items: + - description: CPU and DMA engine registers + - items: + - description: CPU registers + - description: DMA engine registers + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + num-cs: + description: | + Total number of chip selects (default is 1). + Up to 3 native chip selects are supported: + 0: MSIOF_SYNC + 1: MSIOF_SS1 + 2: MSIOF_SS2 + Hardware limitations related to chip selects: + - Native chip selects are always deasserted in between transfers + that are part of the same message. Use cs-gpios to work around + this. + - All slaves using native chip selects must use the same spi-cs-high + configuration. Use cs-gpios to work around this. + - When using GPIO chip selects, at least one native chip select must + be left unused, as it will be driven anyway. + minimum: 1 + maximum: 3 + default: 1 + + dmas: + minItems: 2 + maxItems: 4 + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: [ tx, rx ] + + renesas,dtdl: + description: delay sync signal (setup) in transmit mode. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: + - 0 # no bit delay + - 50 # 0.5-clock-cycle delay + - 100 # 1-clock-cycle delay + - 150 # 1.5-clock-cycle delay + - 200 # 2-clock-cycle delay + + renesas,syncdl: + description: delay sync signal (hold) in transmit mode + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: + - 0 # no bit delay + - 50 # 0.5-clock-cycle delay + - 100 # 1-clock-cycle delay + - 150 # 1.5-clock-cycle delay + - 200 # 2-clock-cycle delay + - 300 # 3-clock-cycle delay + + renesas,tx-fifo-size: + # deprecated for soctype-specific bindings + description: | + Override the default TX fifo size. Unit is words. Ignored if 0. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - maxItems: 1 + default: 64 + + renesas,rx-fifo-size: + # deprecated for soctype-specific bindings + description: | + Override the default RX fifo size. Unit is words. Ignored if 0. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - maxItems: 1 + default: 64 + +required: + - compatible + - reg + - interrupts + - '#address-cells' + - '#size-cells' + +examples: + - | + #include <dt-bindings/clock/r8a7791-clock.h> + #include <dt-bindings/interrupt-controller/irq.h> + + msiof0: spi@e6e20000 { + compatible = "renesas,msiof-r8a7791", "renesas,rcar-gen2-msiof"; + reg = <0 0xe6e20000 0 0x0064>; + interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>; + dmas = <&dmac0 0x51>, <&dmac0 0x52>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-hspi.txt b/Documentation/devicetree/bindings/spi/sh-hspi.txt deleted file mode 100644 index b9d1e4d11a77..000000000000 --- a/Documentation/devicetree/bindings/spi/sh-hspi.txt +++ /dev/null @@ -1,26 +0,0 @@ -Renesas HSPI. - -Required properties: -- compatible : "renesas,hspi-<soctype>", "renesas,hspi" as fallback. - Examples with soctypes are: - - "renesas,hspi-r8a7778" (R-Car M1) - - "renesas,hspi-r8a7779" (R-Car H1) -- reg : Offset and length of the register set for the device -- interrupts : Interrupt specifier -- #address-cells : Must be <1> -- #size-cells : Must be <0> - -Pinctrl properties might be needed, too. See -Documentation/devicetree/bindings/pinctrl/renesas,*. - -Example: - - hspi0: spi@fffc7000 { - compatible = "renesas,hspi-r8a7778", "renesas,hspi"; - reg = <0xfffc7000 0x18>; - interrupt-parent = <&gic>; - interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - }; - diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt deleted file mode 100644 index 18e14ee257b2..000000000000 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ /dev/null @@ -1,105 +0,0 @@ -Renesas MSIOF spi controller - -Required properties: -- compatible : "renesas,msiof-r8a7743" (RZ/G1M) - "renesas,msiof-r8a7744" (RZ/G1N) - "renesas,msiof-r8a7745" (RZ/G1E) - "renesas,msiof-r8a77470" (RZ/G1C) - "renesas,msiof-r8a774a1" (RZ/G2M) - "renesas,msiof-r8a774c0" (RZ/G2E) - "renesas,msiof-r8a7790" (R-Car H2) - "renesas,msiof-r8a7791" (R-Car M2-W) - "renesas,msiof-r8a7792" (R-Car V2H) - "renesas,msiof-r8a7793" (R-Car M2-N) - "renesas,msiof-r8a7794" (R-Car E2) - "renesas,msiof-r8a7795" (R-Car H3) - "renesas,msiof-r8a7796" (R-Car M3-W) - "renesas,msiof-r8a77965" (R-Car M3-N) - "renesas,msiof-r8a77970" (R-Car V3M) - "renesas,msiof-r8a77980" (R-Car V3H) - "renesas,msiof-r8a77990" (R-Car E3) - "renesas,msiof-r8a77995" (R-Car D3) - "renesas,msiof-sh73a0" (SH-Mobile AG5) - "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device) - "renesas,rcar-gen2-msiof" (generic R-Car Gen2 and RZ/G1 compatible device) - "renesas,rcar-gen3-msiof" (generic R-Car Gen3 and RZ/G2 compatible device) - "renesas,sh-msiof" (deprecated) - - When compatible with the generic version, nodes - must list the SoC-specific version corresponding - to the platform first followed by the generic - version. - -- reg : A list of offsets and lengths of the register sets for - the device. - If only one register set is present, it is to be used - by both the CPU and the DMA engine. - If two register sets are present, the first is to be - used by the CPU, and the second is to be used by the - DMA engine. -- interrupts : Interrupt specifier -- #address-cells : Must be <1> -- #size-cells : Must be <0> - -Optional properties: -- clocks : Must contain a reference to the functional clock. -- num-cs : Total number of chip selects (default is 1). - Up to 3 native chip selects are supported: - 0: MSIOF_SYNC - 1: MSIOF_SS1 - 2: MSIOF_SS2 - Hardware limitations related to chip selects: - - Native chip selects are always deasserted in - between transfers that are part of the same - message. Use cs-gpios to work around this. - - All slaves using native chip selects must use the - same spi-cs-high configuration. Use cs-gpios to - work around this. - - When using GPIO chip selects, at least one native - chip select must be left unused, as it will be - driven anyway. -- dmas : Must contain a list of two references to DMA - specifiers, one for transmission, and one for - reception. -- dma-names : Must contain a list of two DMA names, "tx" and "rx". -- spi-slave : Empty property indicating the SPI controller is used - in slave mode. -- renesas,dtdl : delay sync signal (setup) in transmit mode. - Must contain one of the following values: - 0 (no bit delay) - 50 (0.5-clock-cycle delay) - 100 (1-clock-cycle delay) - 150 (1.5-clock-cycle delay) - 200 (2-clock-cycle delay) - -- renesas,syncdl : delay sync signal (hold) in transmit mode. - Must contain one of the following values: - 0 (no bit delay) - 50 (0.5-clock-cycle delay) - 100 (1-clock-cycle delay) - 150 (1.5-clock-cycle delay) - 200 (2-clock-cycle delay) - 300 (3-clock-cycle delay) - -Optional properties, deprecated for soctype-specific bindings: -- renesas,tx-fifo-size : Overrides the default tx fifo size given in words - (default is 64) -- renesas,rx-fifo-size : Overrides the default rx fifo size given in words - (default is 64) - -Pinctrl properties might be needed, too. See -Documentation/devicetree/bindings/pinctrl/renesas,*. - -Example: - - msiof0: spi@e6e20000 { - compatible = "renesas,msiof-r8a7791", - "renesas,rcar-gen2-msiof"; - reg = <0 0xe6e20000 0 0x0064>; - interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>; - dmas = <&dmac0 0x51>, <&dmac0 0x52>; - dma-names = "tx", "rx"; - #address-cells = <1>; - #size-cells = <0>; - }; diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt index f54c8c36395e..3ed08ee9feba 100644 --- a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt @@ -16,7 +16,8 @@ Required properties: Optional properties: - clock-names : Contains the names of the clocks: "ssi_clk", for the core clock used to generate the external SPI clock. - "pclk", the interface clock, required for register access. + "pclk", the interface clock, required for register access. If a clock domain + used to enable this clock then it should be named "pclk_clkdomain". - cs-gpios : Specifies the gpio pins to be used for chipselects. - num-cs : The number of chipselects. If omitted, this will default to 4. - reg-io-width : The I/O register width (in bytes) implemented by this diff --git a/Documentation/devicetree/bindings/spi/spi-sifive.txt b/Documentation/devicetree/bindings/spi/spi-sifive.txt deleted file mode 100644 index 3f5c6e438972..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-sifive.txt +++ /dev/null @@ -1,37 +0,0 @@ -SiFive SPI controller Device Tree Bindings ------------------------------------------- - -Required properties: -- compatible : Should be "sifive,<chip>-spi" and "sifive,spi<version>". - Supported compatible strings are: - "sifive,fu540-c000-spi" for the SiFive SPI v0 as integrated - onto the SiFive FU540 chip, and "sifive,spi0" for the SiFive - SPI v0 IP block with no chip integration tweaks. - Please refer to sifive-blocks-ip-versioning.txt for details -- reg : Physical base address and size of SPI registers map - A second (optional) range can indicate memory mapped flash -- interrupts : Must contain one entry -- interrupt-parent : Must be core interrupt controller -- clocks : Must reference the frequency given to the controller -- #address-cells : Must be '1', indicating which CS to use -- #size-cells : Must be '0' - -Optional properties: -- sifive,fifo-depth : Depth of hardware queues; defaults to 8 -- sifive,max-bits-per-word : Maximum bits per word; defaults to 8 - -SPI RTL that corresponds to the IP block version numbers can be found here: -https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/spi - -Example: - spi: spi@10040000 { - compatible = "sifive,fu540-c000-spi", "sifive,spi0"; - reg = <0x0 0x10040000 0x0 0x1000 0x0 0x20000000 0x0 0x10000000>; - interrupt-parent = <&plic>; - interrupts = <51>; - clocks = <&tlclk>; - #address-cells = <1>; - #size-cells = <0>; - sifive,fifo-depth = <8>; - sifive,max-bits-per-word = <8>; - }; diff --git a/Documentation/devicetree/bindings/spi/spi-sifive.yaml b/Documentation/devicetree/bindings/spi/spi-sifive.yaml new file mode 100644 index 000000000000..140e4351a19f --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sifive.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/spi-sifive.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SiFive SPI controller + +maintainers: + - Pragnesh Patel <pragnesh.patel@sifive.com> + - Paul Walmsley <paul.walmsley@sifive.com> + - Palmer Dabbelt <palmer@sifive.com> + +allOf: + - $ref: "spi-controller.yaml#" + +properties: + compatible: + items: + - const: sifive,fu540-c000-spi + - const: sifive,spi0 + + description: + Should be "sifive,<chip>-spi" and "sifive,spi<version>". + Supported compatible strings are - + "sifive,fu540-c000-spi" for the SiFive SPI v0 as integrated + onto the SiFive FU540 chip, and "sifive,spi0" for the SiFive + SPI v0 IP block with no chip integration tweaks. + Please refer to sifive-blocks-ip-versioning.txt for details + + SPI RTL that corresponds to the IP block version numbers can be found here - + https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/spi + + reg: + maxItems: 1 + + description: + Physical base address and size of SPI registers map + A second (optional) range can indicate memory mapped flash + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + description: + Must reference the frequency given to the controller + + sifive,fifo-depth: + description: + Depth of hardware queues; defaults to 8 + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: [ 8 ] + - default: 8 + + sifive,max-bits-per-word: + description: + Maximum bits per word; defaults to 8 + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: [ 0, 1, 2, 3, 4, 5, 6, 7, 8 ] + - default: 8 + +required: + - compatible + - reg + - interrupts + - clocks + +examples: + - | + spi: spi@10040000 { + compatible = "sifive,fu540-c000-spi", "sifive,spi0"; + reg = <0x0 0x10040000 0x0 0x1000 0x0 0x20000000 0x0 0x10000000>; + interrupt-parent = <&plic>; + interrupts = <51>; + clocks = <&tlclk>; + #address-cells = <1>; + #size-cells = <0>; + sifive,fifo-depth = <8>; + sifive,max-bits-per-word = <8>; + }; + +... diff --git a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt deleted file mode 100644 index bfc038b9478d..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt +++ /dev/null @@ -1,47 +0,0 @@ -* STMicroelectronics Quad Serial Peripheral Interface(QSPI) - -Required properties: -- compatible: should be "st,stm32f469-qspi" -- reg: the first contains the register location and length. - the second contains the memory mapping address and length -- reg-names: should contain the reg names "qspi" "qspi_mm" -- interrupts: should contain the interrupt for the device -- clocks: the phandle of the clock needed by the QSPI controller -- A pinctrl must be defined to set pins in mode of operation for QSPI transfer - -Optional properties: -- resets: must contain the phandle to the reset controller. - -A spi flash (NOR/NAND) must be a child of spi node and could have some -properties. Also see jedec,spi-nor.txt. - -Required properties: -- reg: chip-Select number (QSPI controller may connect 2 flashes) -- spi-max-frequency: max frequency of spi bus - -Optional properties: -- spi-rx-bus-width: see ./spi-bus.txt for the description -- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, -Documentation/devicetree/bindings/dma/dma.txt. -- dma-names: DMA request names should include "tx" and "rx" if present. - -Example: - -qspi: spi@a0001000 { - compatible = "st,stm32f469-qspi"; - reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>; - reg-names = "qspi", "qspi_mm"; - interrupts = <91>; - resets = <&rcc STM32F4_AHB3_RESET(QSPI)>; - clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_qspi0>; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-rx-bus-width = <4>; - spi-max-frequency = <108000000>; - ... - }; -}; diff --git a/Documentation/devicetree/bindings/spi/spi-xilinx.txt b/Documentation/devicetree/bindings/spi/spi-xilinx.txt index dc924a5f71db..5f4ed3e5c994 100644 --- a/Documentation/devicetree/bindings/spi/spi-xilinx.txt +++ b/Documentation/devicetree/bindings/spi/spi-xilinx.txt @@ -8,7 +8,8 @@ Required properties: number. Optional properties: -- xlnx,num-ss-bits : Number of chip selects used. +- xlnx,num-ss-bits : Number of chip selects used. +- xlnx,num-transfer-bits : Number of bits per transfer. This will be 8 if not specified Example: axi_quad_spi@41e00000 { @@ -17,5 +18,6 @@ Example: interrupts = <0 31 1>; reg = <0x41e00000 0x10000>; xlnx,num-ss-bits = <0x1>; + xlnx,num-transfer-bits = <32>; }; diff --git a/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml b/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml new file mode 100644 index 000000000000..3665a5fe6b7f --- /dev/null +++ b/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/st,stm32-qspi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 Quad Serial Peripheral Interface (QSPI) bindings + +maintainers: + - Christophe Kerello <christophe.kerello@st.com> + - Patrice Chotard <patrice.chotard@st.com> + +allOf: + - $ref: "spi-controller.yaml#" + +properties: + compatible: + const: st,stm32f469-qspi + + reg: + items: + - description: registers + - description: memory mapping + + reg-names: + items: + - const: qspi + - const: qspi_mm + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + items: + - description: tx DMA channel + - description: rx DMA channel + + dma-names: + items: + - const: tx + - const: rx + +required: + - compatible + - reg + - reg-names + - clocks + - interrupts + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp1-clks.h> + #include <dt-bindings/reset/stm32mp1-resets.h> + spi@58003000 { + compatible = "st,stm32f469-qspi"; + reg = <0x58003000 0x1000>, <0x70000000 0x10000000>; + reg-names = "qspi", "qspi_mm"; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdma1 22 0x10 0x100002 0x0 0x0>, + <&mdma1 22 0x10 0x100008 0x0 0x0>; + dma-names = "tx", "rx"; + clocks = <&rcc QSPI_K>; + resets = <&rcc QSPI_R>; + + #address-cells = <1>; + #size-cells = <0>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 967e78c5ec0a..05b3904a995b 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -343,6 +343,8 @@ patternProperties: description: Freescale Semiconductor "^fujitsu,.*": description: Fujitsu Ltd. + "^gardena,.*": + description: GARDENA GmbH "^gateworks,.*": description: Gateworks Corporation "^gcw,.*": diff --git a/Documentation/driver-api/libata.rst b/Documentation/driver-api/libata.rst index 70e180e6b93d..207f0d24de69 100644 --- a/Documentation/driver-api/libata.rst +++ b/Documentation/driver-api/libata.rst @@ -250,23 +250,23 @@ High-level taskfile hooks :: - void (*qc_prep) (struct ata_queued_cmd *qc); + enum ata_completion_errors (*qc_prep) (struct ata_queued_cmd *qc); int (*qc_issue) (struct ata_queued_cmd *qc); -Higher-level hooks, these two hooks can potentially supercede several of +Higher-level hooks, these two hooks can potentially supersede several of the above taskfile/DMA engine hooks. ``->qc_prep`` is called after the buffers have been DMA-mapped, and is typically used to populate the -hardware's DMA scatter-gather table. Most drivers use the standard -:c:func:`ata_qc_prep` helper function, but more advanced drivers roll their -own. +hardware's DMA scatter-gather table. Some drivers use the standard +:c:func:`ata_bmdma_qc_prep` and :c:func:`ata_bmdma_dumb_qc_prep` helper +functions, but more advanced drivers roll their own. ``->qc_issue`` is used to make a command active, once the hardware and S/G tables have been prepared. IDE BMDMA drivers use the helper function -:c:func:`ata_qc_issue_prot` for taskfile protocol-based dispatch. More +:c:func:`ata_sff_qc_issue` for taskfile protocol-based dispatch. More advanced drivers implement their own ``->qc_issue``. -:c:func:`ata_qc_issue_prot` calls ``->tf_load()``, ``->bmdma_setup()``, and +:c:func:`ata_sff_qc_issue` calls ``->sff_tf_load()``, ``->bmdma_setup()``, and ``->bmdma_start()`` as necessary to initiate a transfer. Exception and probe handling (EH) diff --git a/Documentation/driver-api/nvmem.rst b/Documentation/driver-api/nvmem.rst index d9d958d5c824..287e86819640 100644 --- a/Documentation/driver-api/nvmem.rst +++ b/Documentation/driver-api/nvmem.rst @@ -129,6 +129,8 @@ To facilitate such consumers NVMEM framework provides below apis:: struct nvmem_device *nvmem_device_get(struct device *dev, const char *name); struct nvmem_device *devm_nvmem_device_get(struct device *dev, const char *name); + struct nvmem_device *nvmem_device_find(void *data, + int (*match)(struct device *dev, const void *data)); void nvmem_device_put(struct nvmem_device *nvmem); int nvmem_device_read(struct nvmem_device *nvmem, unsigned int offset, size_t bytes, void *buf); diff --git a/Documentation/filesystems/fscrypt.rst b/Documentation/filesystems/fscrypt.rst index 8a0700af9596..471a511c7508 100644 --- a/Documentation/filesystems/fscrypt.rst +++ b/Documentation/filesystems/fscrypt.rst @@ -256,13 +256,8 @@ alternative master keys or to support rotating master keys. Instead, the master keys may be wrapped in userspace, e.g. as is done by the `fscrypt <https://github.com/google/fscrypt>`_ tool. -Including the inode number in the IVs was considered. However, it was -rejected as it would have prevented ext4 filesystems from being -resized, and by itself still wouldn't have been sufficient to prevent -the same key from being directly reused for both XTS and CTS-CBC. - -DIRECT_KEY and per-mode keys ----------------------------- +DIRECT_KEY policies +------------------- The Adiantum encryption mode (see `Encryption modes and usage`_) is suitable for both contents and filenames encryption, and it accepts @@ -285,6 +280,21 @@ IV. Moreover: key derived using the KDF. Users may use the same master key for other v2 encryption policies. +IV_INO_LBLK_64 policies +----------------------- + +When FSCRYPT_POLICY_FLAG_IV_INO_LBLK_64 is set in the fscrypt policy, +the encryption keys are derived from the master key, encryption mode +number, and filesystem UUID. This normally results in all files +protected by the same master key sharing a single contents encryption +key and a single filenames encryption key. To still encrypt different +files' data differently, inode numbers are included in the IVs. +Consequently, shrinking the filesystem may not be allowed. + +This format is optimized for use with inline encryption hardware +compliant with the UFS or eMMC standards, which support only 64 IV +bits per I/O request and may have only a small number of keyslots. + Key identifiers --------------- @@ -308,8 +318,9 @@ If unsure, you should use the (AES-256-XTS, AES-256-CTS-CBC) pair. AES-128-CBC was added only for low-powered embedded devices with crypto accelerators such as CAAM or CESA that do not support XTS. To -use AES-128-CBC, CONFIG_CRYPTO_SHA256 (or another SHA-256 -implementation) must be enabled so that ESSIV can be used. +use AES-128-CBC, CONFIG_CRYPTO_ESSIV and CONFIG_CRYPTO_SHA256 (or +another SHA-256 implementation) must be enabled so that ESSIV can be +used. Adiantum is a (primarily) stream cipher-based mode that is fast even on CPUs without dedicated crypto instructions. It's also a true @@ -341,10 +352,16 @@ a little endian number, except that: is encrypted with AES-256 where the AES-256 key is the SHA-256 hash of the file's data encryption key. -- In the "direct key" configuration (FSCRYPT_POLICY_FLAG_DIRECT_KEY - set in the fscrypt_policy), the file's nonce is also appended to the - IV. Currently this is only allowed with the Adiantum encryption - mode. +- With `DIRECT_KEY policies`_, the file's nonce is appended to the IV. + Currently this is only allowed with the Adiantum encryption mode. + +- With `IV_INO_LBLK_64 policies`_, the logical block number is limited + to 32 bits and is placed in bits 0-31 of the IV. The inode number + (which is also limited to 32 bits) is placed in bits 32-63. + +Note that because file logical block numbers are included in the IVs, +filesystems must enforce that blocks are never shifted around within +encrypted files, e.g. via "collapse range" or "insert range". Filenames encryption -------------------- @@ -354,10 +371,10 @@ the requirements to retain support for efficient directory lookups and filenames of up to 255 bytes, the same IV is used for every filename in a directory. -However, each encrypted directory still uses a unique key; or -alternatively (for the "direct key" configuration) has the file's -nonce included in the IVs. Thus, IV reuse is limited to within a -single directory. +However, each encrypted directory still uses a unique key, or +alternatively has the file's nonce (for `DIRECT_KEY policies`_) or +inode number (for `IV_INO_LBLK_64 policies`_) included in the IVs. +Thus, IV reuse is limited to within a single directory. With CTS-CBC, the IV reuse means that when the plaintext filenames share a common prefix at least as long as the cipher block size (16 @@ -431,12 +448,15 @@ This structure must be initialized as follows: (1) for ``contents_encryption_mode`` and FSCRYPT_MODE_AES_256_CTS (4) for ``filenames_encryption_mode``. -- ``flags`` must contain a value from ``<linux/fscrypt.h>`` which - identifies the amount of NUL-padding to use when encrypting - filenames. If unsure, use FSCRYPT_POLICY_FLAGS_PAD_32 (0x3). - Additionally, if the encryption modes are both - FSCRYPT_MODE_ADIANTUM, this can contain - FSCRYPT_POLICY_FLAG_DIRECT_KEY; see `DIRECT_KEY and per-mode keys`_. +- ``flags`` contains optional flags from ``<linux/fscrypt.h>``: + + - FSCRYPT_POLICY_FLAGS_PAD_*: The amount of NUL padding to use when + encrypting filenames. If unsure, use FSCRYPT_POLICY_FLAGS_PAD_32 + (0x3). + - FSCRYPT_POLICY_FLAG_DIRECT_KEY: See `DIRECT_KEY policies`_. + - FSCRYPT_POLICY_FLAG_IV_INO_LBLK_64: See `IV_INO_LBLK_64 + policies`_. This is mutually exclusive with DIRECT_KEY and is not + supported on v1 policies. - For v2 encryption policies, ``__reserved`` must be zeroed. @@ -1089,7 +1109,7 @@ policy structs (see `Setting an encryption policy`_), except that the context structs also contain a nonce. The nonce is randomly generated by the kernel and is used as KDF input or as a tweak to cause different files to be encrypted differently; see `Per-file keys`_ and -`DIRECT_KEY and per-mode keys`_. +`DIRECT_KEY policies`_. Data path changes ----------------- diff --git a/Documentation/filesystems/fsverity.rst b/Documentation/filesystems/fsverity.rst index 42a0b6dd9e0b..a95536b6443c 100644 --- a/Documentation/filesystems/fsverity.rst +++ b/Documentation/filesystems/fsverity.rst @@ -226,6 +226,14 @@ To do so, check for FS_VERITY_FL (0x00100000) in the returned flags. The verity flag is not settable via FS_IOC_SETFLAGS. You must use FS_IOC_ENABLE_VERITY instead, since parameters must be provided. +statx +----- + +Since Linux v5.5, the statx() system call sets STATX_ATTR_VERITY if +the file has fs-verity enabled. This can perform better than +FS_IOC_GETFLAGS and FS_IOC_MEASURE_VERITY because it doesn't require +opening the file, and opening verity files can be expensive. + Accessing verity files ====================== @@ -398,7 +406,7 @@ pages have been read into the pagecache. (See `Verifying data`_.) ext4 ---- -ext4 supports fs-verity since Linux TODO and e2fsprogs v1.45.2. +ext4 supports fs-verity since Linux v5.4 and e2fsprogs v1.45.2. To create verity files on an ext4 filesystem, the filesystem must have been formatted with ``-O verity`` or had ``tune2fs -O verity`` run on @@ -434,7 +442,7 @@ also only supports extent-based files. f2fs ---- -f2fs supports fs-verity since Linux TODO and f2fs-tools v1.11.0. +f2fs supports fs-verity since Linux v5.4 and f2fs-tools v1.11.0. To create verity files on an f2fs filesystem, the filesystem must have been formatted with ``-O verity``. diff --git a/Documentation/ioctl/ioctl-number.rst b/Documentation/ioctl/ioctl-number.rst index bef79cd4c6b4..4ef86433bd67 100644 --- a/Documentation/ioctl/ioctl-number.rst +++ b/Documentation/ioctl/ioctl-number.rst @@ -233,6 +233,7 @@ Code Seq# Include File Comments 'f' 00-0F fs/ext4/ext4.h conflict! 'f' 00-0F linux/fs.h conflict! 'f' 00-0F fs/ocfs2/ocfs2_fs.h conflict! +'f' 13-27 linux/fscrypt.h 'f' 81-8F linux/fsverity.h 'g' 00-0F linux/usb/gadgetfs.h 'g' 20-2F linux/usb/g_printer.h diff --git a/Documentation/livepatch/index.rst b/Documentation/livepatch/index.rst index 17674a9e21b2..525944063be7 100644 --- a/Documentation/livepatch/index.rst +++ b/Documentation/livepatch/index.rst @@ -12,6 +12,7 @@ Kernel Livepatching cumulative-patches module-elf-format shadow-vars + system-state .. only:: subproject and html diff --git a/Documentation/livepatch/system-state.rst b/Documentation/livepatch/system-state.rst new file mode 100644 index 000000000000..c6d127c2d9aa --- /dev/null +++ b/Documentation/livepatch/system-state.rst @@ -0,0 +1,167 @@ +==================== +System State Changes +==================== + +Some users are really reluctant to reboot a system. This brings the need +to provide more livepatches and maintain some compatibility between them. + +Maintaining more livepatches is much easier with cumulative livepatches. +Each new livepatch completely replaces any older one. It can keep, +add, and even remove fixes. And it is typically safe to replace any version +of the livepatch with any other one thanks to the atomic replace feature. + +The problems might come with shadow variables and callbacks. They might +change the system behavior or state so that it is no longer safe to +go back and use an older livepatch or the original kernel code. Also +any new livepatch must be able to detect what changes have already been +done by the already installed livepatches. + +This is where the livepatch system state tracking gets useful. It +allows to: + + - store data needed to manipulate and restore the system state + + - define compatibility between livepatches using a change id + and version + + +1. Livepatch system state API +============================= + +The state of the system might get modified either by several livepatch callbacks +or by the newly used code. Also it must be possible to find changes done by +already installed livepatches. + +Each modified state is described by struct klp_state, see +include/linux/livepatch.h. + +Each livepatch defines an array of struct klp_states. They mention +all states that the livepatch modifies. + +The livepatch author must define the following two fields for each +struct klp_state: + + - *id* + + - Non-zero number used to identify the affected system state. + + - *version* + + - Number describing the variant of the system state change that + is supported by the given livepatch. + +The state can be manipulated using two functions: + + - *klp_get_state(patch, id)* + + - Get struct klp_state associated with the given livepatch + and state id. + + - *klp_get_prev_state(id)* + + - Get struct klp_state associated with the given feature id and + already installed livepatches. + +2. Livepatch compatibility +========================== + +The system state version is used to prevent loading incompatible livepatches. +The check is done when the livepatch is enabled. The rules are: + + - Any completely new system state modification is allowed. + + - System state modifications with the same or higher version are allowed + for already modified system states. + + - Cumulative livepatches must handle all system state modifications from + already installed livepatches. + + - Non-cumulative livepatches are allowed to touch already modified + system states. + +3. Supported scenarios +====================== + +Livepatches have their life-cycle and the same is true for the system +state changes. Every compatible livepatch has to support the following +scenarios: + + - Modify the system state when the livepatch gets enabled and the state + has not been already modified by a livepatches that are being + replaced. + + - Take over or update the system state modification when is has already + been done by a livepatch that is being replaced. + + - Restore the original state when the livepatch is disabled. + + - Restore the previous state when the transition is reverted. + It might be the original system state or the state modification + done by livepatches that were being replaced. + + - Remove any already made changes when error occurs and the livepatch + cannot get enabled. + +4. Expected usage +================= + +System states are usually modified by livepatch callbacks. The expected +role of each callback is as follows: + +*pre_patch()* + + - Allocate *state->data* when necessary. The allocation might fail + and *pre_patch()* is the only callback that could stop loading + of the livepatch. The allocation is not needed when the data + are already provided by previously installed livepatches. + + - Do any other preparatory action that is needed by + the new code even before the transition gets finished. + For example, initialize *state->data*. + + The system state itself is typically modified in *post_patch()* + when the entire system is able to handle it. + + - Clean up its own mess in case of error. It might be done by a custom + code or by calling *post_unpatch()* explicitly. + +*post_patch()* + + - Copy *state->data* from the previous livepatch when they are + compatible. + + - Do the actual system state modification. Eventually allow + the new code to use it. + + - Make sure that *state->data* has all necessary information. + + - Free *state->data* from replaces livepatches when they are + not longer needed. + +*pre_unpatch()* + + - Prevent the code, added by the livepatch, relying on the system + state change. + + - Revert the system state modification.. + +*post_unpatch()* + + - Distinguish transition reverse and livepatch disabling by + checking *klp_get_prev_state()*. + + - In case of transition reverse, restore the previous system + state. It might mean doing nothing. + + - Remove any not longer needed setting or data. + +.. note:: + + *pre_unpatch()* typically does symmetric operations to *post_patch()*. + Except that it is called only when the livepatch is being disabled. + Therefore it does not need to care about any previously installed + livepatch. + + *post_unpatch()* typically does symmetric operations to *pre_patch()*. + It might be called also during the transition reverse. Therefore it + has to handle the state of the previously installed livepatches. diff --git a/Documentation/networking/af_xdp.rst b/Documentation/networking/af_xdp.rst index 83f7ae5fc045..5bc55a4e3bce 100644 --- a/Documentation/networking/af_xdp.rst +++ b/Documentation/networking/af_xdp.rst @@ -40,13 +40,13 @@ allocates memory for this UMEM using whatever means it feels is most appropriate (malloc, mmap, huge pages, etc). This memory area is then registered with the kernel using the new setsockopt XDP_UMEM_REG. The UMEM also has two rings: the FILL ring and the COMPLETION ring. The -fill ring is used by the application to send down addr for the kernel +FILL ring is used by the application to send down addr for the kernel to fill in with RX packet data. References to these frames will then appear in the RX ring once each packet has been received. The -completion ring, on the other hand, contains frame addr that the +COMPLETION ring, on the other hand, contains frame addr that the kernel has transmitted completely and can now be used again by user space, for either TX or RX. Thus, the frame addrs appearing in the -completion ring are addrs that were previously transmitted using the +COMPLETION ring are addrs that were previously transmitted using the TX ring. In summary, the RX and FILL rings are used for the RX path and the TX and COMPLETION rings are used for the TX path. @@ -91,11 +91,16 @@ Concepts ======== In order to use an AF_XDP socket, a number of associated objects need -to be setup. +to be setup. These objects and their options are explained in the +following sections. -Jonathan Corbet has also written an excellent article on LWN, -"Accelerating networking with AF_XDP". It can be found at -https://lwn.net/Articles/750845/. +For an overview on how AF_XDP works, you can also take a look at the +Linux Plumbers paper from 2018 on the subject: +http://vger.kernel.org/lpc_net2018_talks/lpc18_paper_af_xdp_perf-v2.pdf. Do +NOT consult the paper from 2017 on "AF_PACKET v4", the first attempt +at AF_XDP. Nearly everything changed since then. Jonathan Corbet has +also written an excellent article on LWN, "Accelerating networking +with AF_XDP". It can be found at https://lwn.net/Articles/750845/. UMEM ---- @@ -113,22 +118,22 @@ the next socket B can do this by setting the XDP_SHARED_UMEM flag in struct sockaddr_xdp member sxdp_flags, and passing the file descriptor of A to struct sockaddr_xdp member sxdp_shared_umem_fd. -The UMEM has two single-producer/single-consumer rings, that are used +The UMEM has two single-producer/single-consumer rings that are used to transfer ownership of UMEM frames between the kernel and the user-space application. Rings ----- -There are a four different kind of rings: Fill, Completion, RX and +There are a four different kind of rings: FILL, COMPLETION, RX and TX. All rings are single-producer/single-consumer, so the user-space application need explicit synchronization of multiple processes/threads are reading/writing to them. -The UMEM uses two rings: Fill and Completion. Each socket associated +The UMEM uses two rings: FILL and COMPLETION. Each socket associated with the UMEM must have an RX queue, TX queue or both. Say, that there is a setup with four sockets (all doing TX and RX). Then there will be -one Fill ring, one Completion ring, four TX rings and four RX rings. +one FILL ring, one COMPLETION ring, four TX rings and four RX rings. The rings are head(producer)/tail(consumer) based rings. A producer writes the data ring at the index pointed out by struct xdp_ring @@ -146,7 +151,7 @@ The size of the rings need to be of size power of two. UMEM Fill Ring ~~~~~~~~~~~~~~ -The Fill ring is used to transfer ownership of UMEM frames from +The FILL ring is used to transfer ownership of UMEM frames from user-space to kernel-space. The UMEM addrs are passed in the ring. As an example, if the UMEM is 64k and each chunk is 4k, then the UMEM has 16 chunks and can pass addrs between 0 and 64k. @@ -164,8 +169,8 @@ chunks mode, then the incoming addr will be left untouched. UMEM Completion Ring ~~~~~~~~~~~~~~~~~~~~ -The Completion Ring is used transfer ownership of UMEM frames from -kernel-space to user-space. Just like the Fill ring, UMEM indicies are +The COMPLETION Ring is used transfer ownership of UMEM frames from +kernel-space to user-space. Just like the FILL ring, UMEM indices are used. Frames passed from the kernel to user-space are frames that has been @@ -181,7 +186,7 @@ The RX ring is the receiving side of a socket. Each entry in the ring is a struct xdp_desc descriptor. The descriptor contains UMEM offset (addr) and the length of the data (len). -If no frames have been passed to kernel via the Fill ring, no +If no frames have been passed to kernel via the FILL ring, no descriptors will (or can) appear on the RX ring. The user application consumes struct xdp_desc descriptors from this @@ -199,8 +204,24 @@ be relaxed in the future. The user application produces struct xdp_desc descriptors to this ring. +Libbpf +====== + +Libbpf is a helper library for eBPF and XDP that makes using these +technologies a lot simpler. It also contains specific helper functions +in tools/lib/bpf/xsk.h for facilitating the use of AF_XDP. It +contains two types of functions: those that can be used to make the +setup of AF_XDP socket easier and ones that can be used in the data +plane to access the rings safely and quickly. To see an example on how +to use this API, please take a look at the sample application in +samples/bpf/xdpsock_usr.c which uses libbpf for both setup and data +plane operations. + +We recommend that you use this library unless you have become a power +user. It will make your program a lot simpler. + XSKMAP / BPF_MAP_TYPE_XSKMAP ----------------------------- +============================ On XDP side there is a BPF map type BPF_MAP_TYPE_XSKMAP (XSKMAP) that is used in conjunction with bpf_redirect_map() to pass the ingress @@ -216,21 +237,202 @@ queue 17. Only the XDP program executing for eth0 and queue 17 will successfully pass data to the socket. Please refer to the sample application (samples/bpf/) in for an example. +Configuration Flags and Socket Options +====================================== + +These are the various configuration flags that can be used to control +and monitor the behavior of AF_XDP sockets. + +XDP_COPY and XDP_ZERO_COPY bind flags +------------------------------------- + +When you bind to a socket, the kernel will first try to use zero-copy +copy. If zero-copy is not supported, it will fall back on using copy +mode, i.e. copying all packets out to user space. But if you would +like to force a certain mode, you can use the following flags. If you +pass the XDP_COPY flag to the bind call, the kernel will force the +socket into copy mode. If it cannot use copy mode, the bind call will +fail with an error. Conversely, the XDP_ZERO_COPY flag will force the +socket into zero-copy mode or fail. + +XDP_SHARED_UMEM bind flag +------------------------- + +This flag enables you to bind multiple sockets to the same UMEM, but +only if they share the same queue id. In this mode, each socket has +their own RX and TX rings, but the UMEM (tied to the fist socket +created) only has a single FILL ring and a single COMPLETION +ring. To use this mode, create the first socket and bind it in the normal +way. Create a second socket and create an RX and a TX ring, or at +least one of them, but no FILL or COMPLETION rings as the ones from +the first socket will be used. In the bind call, set he +XDP_SHARED_UMEM option and provide the initial socket's fd in the +sxdp_shared_umem_fd field. You can attach an arbitrary number of extra +sockets this way. + +What socket will then a packet arrive on? This is decided by the XDP +program. Put all the sockets in the XSK_MAP and just indicate which +index in the array you would like to send each packet to. A simple +round-robin example of distributing packets is shown below: + +.. code-block:: c + + #include <linux/bpf.h> + #include "bpf_helpers.h" + + #define MAX_SOCKS 16 + + struct { + __uint(type, BPF_MAP_TYPE_XSKMAP); + __uint(max_entries, MAX_SOCKS); + __uint(key_size, sizeof(int)); + __uint(value_size, sizeof(int)); + } xsks_map SEC(".maps"); + + static unsigned int rr; + + SEC("xdp_sock") int xdp_sock_prog(struct xdp_md *ctx) + { + rr = (rr + 1) & (MAX_SOCKS - 1); + + return bpf_redirect_map(&xsks_map, rr, XDP_DROP); + } + +Note, that since there is only a single set of FILL and COMPLETION +rings, and they are single producer, single consumer rings, you need +to make sure that multiple processes or threads do not use these rings +concurrently. There are no synchronization primitives in the +libbpf code that protects multiple users at this point in time. + +Libbpf uses this mode if you create more than one socket tied to the +same umem. However, note that you need to supply the +XSK_LIBBPF_FLAGS__INHIBIT_PROG_LOAD libbpf_flag with the +xsk_socket__create calls and load your own XDP program as there is no +built in one in libbpf that will route the traffic for you. + +XDP_USE_NEED_WAKEUP bind flag +----------------------------- + +This option adds support for a new flag called need_wakeup that is +present in the FILL ring and the TX ring, the rings for which user +space is a producer. When this option is set in the bind call, the +need_wakeup flag will be set if the kernel needs to be explicitly +woken up by a syscall to continue processing packets. If the flag is +zero, no syscall is needed. + +If the flag is set on the FILL ring, the application needs to call +poll() to be able to continue to receive packets on the RX ring. This +can happen, for example, when the kernel has detected that there are no +more buffers on the FILL ring and no buffers left on the RX HW ring of +the NIC. In this case, interrupts are turned off as the NIC cannot +receive any packets (as there are no buffers to put them in), and the +need_wakeup flag is set so that user space can put buffers on the +FILL ring and then call poll() so that the kernel driver can put these +buffers on the HW ring and start to receive packets. + +If the flag is set for the TX ring, it means that the application +needs to explicitly notify the kernel to send any packets put on the +TX ring. This can be accomplished either by a poll() call, as in the +RX path, or by calling sendto(). + +An example of how to use this flag can be found in +samples/bpf/xdpsock_user.c. An example with the use of libbpf helpers +would look like this for the TX path: + +.. code-block:: c + + if (xsk_ring_prod__needs_wakeup(&my_tx_ring)) + sendto(xsk_socket__fd(xsk_handle), NULL, 0, MSG_DONTWAIT, NULL, 0); + +I.e., only use the syscall if the flag is set. + +We recommend that you always enable this mode as it usually leads to +better performance especially if you run the application and the +driver on the same core, but also if you use different cores for the +application and the kernel driver, as it reduces the number of +syscalls needed for the TX path. + +XDP_{RX|TX|UMEM_FILL|UMEM_COMPLETION}_RING setsockopts +------------------------------------------------------ + +These setsockopts sets the number of descriptors that the RX, TX, +FILL, and COMPLETION rings respectively should have. It is mandatory +to set the size of at least one of the RX and TX rings. If you set +both, you will be able to both receive and send traffic from your +application, but if you only want to do one of them, you can save +resources by only setting up one of them. Both the FILL ring and the +COMPLETION ring are mandatory as you need to have a UMEM tied to your +socket. But if the XDP_SHARED_UMEM flag is used, any socket after the +first one does not have a UMEM and should in that case not have any +FILL or COMPLETION rings created as the ones from the shared umem will +be used. Note, that the rings are single-producer single-consumer, so +do not try to access them from multiple processes at the same +time. See the XDP_SHARED_UMEM section. + +In libbpf, you can create Rx-only and Tx-only sockets by supplying +NULL to the rx and tx arguments, respectively, to the +xsk_socket__create function. + +If you create a Tx-only socket, we recommend that you do not put any +packets on the fill ring. If you do this, drivers might think you are +going to receive something when you in fact will not, and this can +negatively impact performance. + +XDP_UMEM_REG setsockopt +----------------------- + +This setsockopt registers a UMEM to a socket. This is the area that +contain all the buffers that packet can recide in. The call takes a +pointer to the beginning of this area and the size of it. Moreover, it +also has parameter called chunk_size that is the size that the UMEM is +divided into. It can only be 2K or 4K at the moment. If you have an +UMEM area that is 128K and a chunk size of 2K, this means that you +will be able to hold a maximum of 128K / 2K = 64 packets in your UMEM +area and that your largest packet size can be 2K. + +There is also an option to set the headroom of each single buffer in +the UMEM. If you set this to N bytes, it means that the packet will +start N bytes into the buffer leaving the first N bytes for the +application to use. The final option is the flags field, but it will +be dealt with in separate sections for each UMEM flag. + +XDP_STATISTICS getsockopt +------------------------- + +Gets drop statistics of a socket that can be useful for debug +purposes. The supported statistics are shown below: + +.. code-block:: c + + struct xdp_statistics { + __u64 rx_dropped; /* Dropped for reasons other than invalid desc */ + __u64 rx_invalid_descs; /* Dropped due to invalid descriptor */ + __u64 tx_invalid_descs; /* Dropped due to invalid descriptor */ + }; + +XDP_OPTIONS getsockopt +---------------------- + +Gets options from an XDP socket. The only one supported so far is +XDP_OPTIONS_ZEROCOPY which tells you if zero-copy is on or not. + Usage ===== -In order to use AF_XDP sockets there are two parts needed. The +In order to use AF_XDP sockets two parts are needed. The user-space application and the XDP program. For a complete setup and usage example, please refer to the sample application. The user-space side is xdpsock_user.c and the XDP side is part of libbpf. -The XDP code sample included in tools/lib/bpf/xsk.c is the following:: +The XDP code sample included in tools/lib/bpf/xsk.c is the following: + +.. code-block:: c SEC("xdp_sock") int xdp_sock_prog(struct xdp_md *ctx) { int index = ctx->rx_queue_index; - // A set entry here means that the correspnding queue_id + // A set entry here means that the corresponding queue_id // has an active AF_XDP socket bound to it. if (bpf_map_lookup_elem(&xsks_map, &index)) return bpf_redirect_map(&xsks_map, index, 0); @@ -238,7 +440,10 @@ The XDP code sample included in tools/lib/bpf/xsk.c is the following:: return XDP_PASS; } -Naive ring dequeue and enqueue could look like this:: +A simple but not so performance ring dequeue and enqueue could look +like this: + +.. code-block:: c // struct xdp_rxtx_ring { // __u32 *producer; @@ -287,17 +492,16 @@ Naive ring dequeue and enqueue could look like this:: return 0; } - -For a more optimized version, please refer to the sample application. +But please use the libbpf functions as they are optimized and ready to +use. Will make your life easier. Sample application ================== There is a xdpsock benchmarking/test application included that -demonstrates how to use AF_XDP sockets with both private and shared -UMEMs. Say that you would like your UDP traffic from port 4242 to end -up in queue 16, that we will enable AF_XDP on. Here, we use ethtool -for this:: +demonstrates how to use AF_XDP sockets with private UMEMs. Say that +you would like your UDP traffic from port 4242 to end up in queue 16, +that we will enable AF_XDP on. Here, we use ethtool for this:: ethtool -N p3p2 rx-flow-hash udp4 fn ethtool -N p3p2 flow-type udp4 src-port 4242 dst-port 4242 \ @@ -311,13 +515,18 @@ using:: For XDP_SKB mode, use the switch "-S" instead of "-N" and all options can be displayed with "-h", as usual. +This sample application uses libbpf to make the setup and usage of +AF_XDP simpler. If you want to know how the raw uapi of AF_XDP is +really used to make something more advanced, take a look at the libbpf +code in tools/lib/bpf/xsk.[ch]. + FAQ ======= Q: I am not seeing any traffic on the socket. What am I doing wrong? A: When a netdev of a physical NIC is initialized, Linux usually - allocates one Rx and Tx queue pair per core. So on a 8 core system, + allocates one RX and TX queue pair per core. So on a 8 core system, queue ids 0 to 7 will be allocated, one per core. In the AF_XDP bind call or the xsk_socket__create libbpf function call, you specify a specific queue id to bind to and it is only the traffic @@ -343,9 +552,21 @@ A: When a netdev of a physical NIC is initialized, Linux usually sudo ethtool -N <interface> flow-type udp4 src-port 4242 dst-port \ 4242 action 2 - A number of other ways are possible all up to the capabilitites of + A number of other ways are possible all up to the capabilities of the NIC you have. +Q: Can I use the XSKMAP to implement a switch betwen different umems + in copy mode? + +A: The short answer is no, that is not supported at the moment. The + XSKMAP can only be used to switch traffic coming in on queue id X + to sockets bound to the same queue id X. The XSKMAP can contain + sockets bound to different queue ids, for example X and Y, but only + traffic goming in from queue id Y can be directed to sockets bound + to the same queue id Y. In zero-copy mode, you should use the + switch, or other distribution mechanism, in your NIC to direct + traffic to the correct queue id and socket. + Credits ======= diff --git a/Documentation/networking/device_drivers/aquantia/atlantic.txt b/Documentation/networking/device_drivers/aquantia/atlantic.txt index d235cbaeccc6..2013fcedc2da 100644 --- a/Documentation/networking/device_drivers/aquantia/atlantic.txt +++ b/Documentation/networking/device_drivers/aquantia/atlantic.txt @@ -1,5 +1,5 @@ -aQuantia AQtion Driver for the aQuantia Multi-Gigabit PCI Express Family of -Ethernet Adapters +Marvell(Aquantia) AQtion Driver for the aQuantia Multi-Gigabit PCI Express +Family of Ethernet Adapters ============================================================================= Contents @@ -325,6 +325,46 @@ Supported ethtool options Example: ethtool -N eth0 flow-type udp4 action 0 loc 32 + UDP GSO hardware offload + --------------------------------- + UDP GSO allows to boost UDP tx rates by offloading UDP headers allocation + into hardware. A special userspace socket option is required for this, + could be validated with /kernel/tools/testing/selftests/net/ + + udpgso_bench_tx -u -4 -D 10.0.1.1 -s 6300 -S 100 + + Will cause sending out of 100 byte sized UDP packets formed from single + 6300 bytes user buffer. + + UDP GSO is configured by: + + ethtool -K eth0 tx-udp-segmentation on + + Private flags (testing) + --------------------------------- + + Atlantic driver supports private flags for hardware custom features: + + $ ethtool --show-priv-flags ethX + + Private flags for ethX: + DMASystemLoopback : off + PKTSystemLoopback : off + DMANetworkLoopback : off + PHYInternalLoopback: off + PHYExternalLoopback: off + + Example: + + $ ethtool --set-priv-flags ethX DMASystemLoopback on + + DMASystemLoopback: DMA Host loopback. + PKTSystemLoopback: Packet buffer host loopback. + DMANetworkLoopback: Network side loopback on DMA block. + PHYInternalLoopback: Internal loopback on Phy. + PHYExternalLoopback: External loopback on Phy (with loopback ethernet cable). + + Command Line Parameters ======================= The following command line parameters are available on atlantic driver: @@ -426,7 +466,7 @@ Support If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information related -to the issue to support@aquantia.com +to the issue to aqn_support@marvell.com License ======= diff --git a/Documentation/networking/device_drivers/freescale/dpaa.txt b/Documentation/networking/device_drivers/freescale/dpaa.txt index f88194f71c54..b06601ff9200 100644 --- a/Documentation/networking/device_drivers/freescale/dpaa.txt +++ b/Documentation/networking/device_drivers/freescale/dpaa.txt @@ -129,9 +129,9 @@ CONFIG_AQUANTIA_PHY=y DPAA Ethernet Frame Processing ============================== -On Rx, buffers for the incoming frames are retrieved from one of the three -existing buffers pools. The driver initializes and seeds these, each with -buffers of different sizes: 1KB, 2KB and 4KB. +On Rx, buffers for the incoming frames are retrieved from the buffers found +in the dedicated interface buffer pool. The driver initializes and seeds these +with one page buffers. On Tx, all transmitted frames are returned to the driver through Tx confirmation frame queues. The driver is then responsible for freeing the @@ -254,7 +254,7 @@ The following statistics are exported for each interface through ethtool: The driver also exports the following information in sysfs: - the FQ IDs for each FQ type - /sys/devices/platform/dpaa-ethernet.0/net/<int>/fqids + /sys/devices/platform/soc/<addr>.fman/<addr>.ethernet/dpaa-ethernet.<id>/net/fm<nr>-mac<nr>/fqids - - the IDs of the buffer pools in use - /sys/devices/platform/dpaa-ethernet.0/net/<int>/bpids + - the ID of the buffer pool in use + /sys/devices/platform/soc/<addr>.fman/<addr>.ethernet/dpaa-ethernet.<id>/net/fm<nr>-mac<nr>/bpids diff --git a/Documentation/networking/device_drivers/freescale/dpaa2/index.rst b/Documentation/networking/device_drivers/freescale/dpaa2/index.rst index 67bd87fe6c53..ee40fcc5ddff 100644 --- a/Documentation/networking/device_drivers/freescale/dpaa2/index.rst +++ b/Documentation/networking/device_drivers/freescale/dpaa2/index.rst @@ -8,3 +8,4 @@ DPAA2 Documentation overview dpio-driver ethernet-driver + mac-phy-support diff --git a/Documentation/networking/device_drivers/freescale/dpaa2/mac-phy-support.rst b/Documentation/networking/device_drivers/freescale/dpaa2/mac-phy-support.rst new file mode 100644 index 000000000000..51e6624fb774 --- /dev/null +++ b/Documentation/networking/device_drivers/freescale/dpaa2/mac-phy-support.rst @@ -0,0 +1,191 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +======================= +DPAA2 MAC / PHY support +======================= + +:Copyright: |copy| 2019 NXP + +Overview +-------- + +The DPAA2 MAC / PHY support consists of a set of APIs that help DPAA2 network +drivers (dpaa2-eth, dpaa2-ethsw) interract with the PHY library. + +DPAA2 Software Architecture +--------------------------- + +Among other DPAA2 objects, the fsl-mc bus exports DPNI objects (abstracting a +network interface) and DPMAC objects (abstracting a MAC). The dpaa2-eth driver +probes on the DPNI object and connects to and configures a DPMAC object with +the help of phylink. + +Data connections may be established between a DPNI and a DPMAC, or between two +DPNIs. Depending on the connection type, the netif_carrier_[on/off] is handled +directly by the dpaa2-eth driver or by phylink. + +.. code-block:: none + + Sources of abstracted link state information presented by the MC firmware + + +--------------------------------------+ + +------------+ +---------+ | xgmac_mdio | + | net_device | | phylink |--| +-----+ +-----+ +-----+ +-----+ | + +------------+ +---------+ | | PHY | | PHY | | PHY | | PHY | | + | | | +-----+ +-----+ +-----+ +-----+ | + +------------------------------------+ | External MDIO bus | + | dpaa2-eth | +--------------------------------------+ + +------------------------------------+ + | | Linux + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + | | MC firmware + | /| V + +----------+ / | +----------+ + | | / | | | + | | | | | | + | DPNI |<------| |<------| DPMAC | + | | | | | | + | | \ |<---+ | | + +----------+ \ | | +----------+ + \| | + | + +--------------------------------------+ + | MC firmware polling MAC PCS for link | + | +-----+ +-----+ +-----+ +-----+ | + | | PCS | | PCS | | PCS | | PCS | | + | +-----+ +-----+ +-----+ +-----+ | + | Internal MDIO bus | + +--------------------------------------+ + + +Depending on an MC firmware configuration setting, each MAC may be in one of two modes: + +- DPMAC_LINK_TYPE_FIXED: the link state management is handled exclusively by + the MC firmware by polling the MAC PCS. Without the need to register a + phylink instance, the dpaa2-eth driver will not bind to the connected dpmac + object at all. + +- DPMAC_LINK_TYPE_PHY: The MC firmware is left waiting for link state update + events, but those are in fact passed strictly between the dpaa2-mac (based on + phylink) and its attached net_device driver (dpaa2-eth, dpaa2-ethsw), + effectively bypassing the firmware. + +Implementation +-------------- + +At probe time or when a DPNI's endpoint is dynamically changed, the dpaa2-eth +is responsible to find out if the peer object is a DPMAC and if this is the +case, to integrate it with PHYLINK using the dpaa2_mac_connect() API, which +will do the following: + + - look up the device tree for PHYLINK-compatible of binding (phy-handle) + - will create a PHYLINK instance associated with the received net_device + - connect to the PHY using phylink_of_phy_connect() + +The following phylink_mac_ops callback are implemented: + + - .validate() will populate the supported linkmodes with the MAC capabilities + only when the phy_interface_t is RGMII_* (at the moment, this is the only + link type supported by the driver). + + - .mac_config() will configure the MAC in the new configuration using the + dpmac_set_link_state() MC firmware API. + + - .mac_link_up() / .mac_link_down() will update the MAC link using the same + API described above. + +At driver unbind() or when the DPNI object is disconnected from the DPMAC, the +dpaa2-eth driver calls dpaa2_mac_disconnect() which will, in turn, disconnect +from the PHY and destroy the PHYLINK instance. + +In case of a DPNI-DPMAC connection, an 'ip link set dev eth0 up' would start +the following sequence of operations: + +(1) phylink_start() called from .dev_open(). +(2) The .mac_config() and .mac_link_up() callbacks are called by PHYLINK. +(3) In order to configure the HW MAC, the MC Firmware API + dpmac_set_link_state() is called. +(4) The firmware will eventually setup the HW MAC in the new configuration. +(5) A netif_carrier_on() call is made directly from PHYLINK on the associated + net_device. +(6) The dpaa2-eth driver handles the LINK_STATE_CHANGE irq in order to + enable/disable Rx taildrop based on the pause frame settings. + +.. code-block:: none + + +---------+ +---------+ + | PHYLINK |-------------->| eth0 | + +---------+ (5) +---------+ + (1) ^ | + | | + | v (2) + +-----------------------------------+ + | dpaa2-eth | + +-----------------------------------+ + | ^ (6) + | | + v (3) | + +---------+---------------+---------+ + | DPMAC | | DPNI | + +---------+ +---------+ + | MC Firmware | + +-----------------------------------+ + | + | + v (4) + +-----------------------------------+ + | HW MAC | + +-----------------------------------+ + +In case of a DPNI-DPNI connection, a usual sequence of operations looks like +the following: + +(1) ip link set dev eth0 up +(2) The dpni_enable() MC API called on the associated fsl_mc_device. +(3) ip link set dev eth1 up +(4) The dpni_enable() MC API called on the associated fsl_mc_device. +(5) The LINK_STATE_CHANGED irq is received by both instances of the dpaa2-eth + driver because now the operational link state is up. +(6) The netif_carrier_on() is called on the exported net_device from + link_state_update(). + +.. code-block:: none + + +---------+ +---------+ + | eth0 | | eth1 | + +---------+ +---------+ + | ^ ^ | + | | | | + (1) v | (6) (6) | v (3) + +---------+ +---------+ + |dpaa2-eth| |dpaa2-eth| + +---------+ +---------+ + | ^ ^ | + | | | | + (2) v | (5) (5) | v (4) + +---------+---------------+---------+ + | DPNI | | DPNI | + +---------+ +---------+ + | MC Firmware | + +-----------------------------------+ + + +Exported API +------------ + +Any DPAA2 driver that drivers endpoints of DPMAC objects should service its +_EVENT_ENDPOINT_CHANGED irq and connect/disconnect from the associated DPMAC +when necessary using the below listed API:: + + - int dpaa2_mac_connect(struct dpaa2_mac *mac); + - void dpaa2_mac_disconnect(struct dpaa2_mac *mac); + +A phylink integration is necessary only when the partner DPMAC is not of TYPE_FIXED. +One can check for this condition using the below API:: + + - bool dpaa2_mac_is_type_fixed(struct fsl_mc_device *dpmac_dev,struct fsl_mc_io *mc_io); + +Before connection to a MAC, the caller must allocate and populate the +dpaa2_mac structure with the associated net_device, a pointer to the MC portal +to be used and the actual fsl_mc_device structure of the DPMAC. diff --git a/Documentation/networking/device_drivers/mellanox/mlx5.rst b/Documentation/networking/device_drivers/mellanox/mlx5.rst index d071c6b49e1f..7599dceba9f1 100644 --- a/Documentation/networking/device_drivers/mellanox/mlx5.rst +++ b/Documentation/networking/device_drivers/mellanox/mlx5.rst @@ -154,6 +154,27 @@ User command examples: values: cmode runtime value smfs +enable_roce: RoCE enablement state +---------------------------------- +RoCE enablement state controls driver support for RoCE traffic. +When RoCE is disabled, there is no gid table, only raw ethernet QPs are supported and traffic on the well known UDP RoCE port is handled as raw ethernet traffic. + +To change RoCE enablement state a user must change the driverinit cmode value and run devlink reload. + +User command examples: + +- Disable RoCE:: + + $ devlink dev param set pci/0000:06:00.0 name enable_roce value false cmode driverinit + $ devlink dev reload pci/0000:06:00.0 + +- Read RoCE enablement state:: + + $ devlink dev param show pci/0000:06:00.0 name enable_roce + pci/0000:06:00.0: + name enable_roce type generic + values: + cmode driverinit value true Devlink health reporters ======================== diff --git a/Documentation/networking/device_drivers/ti/cpsw_switchdev.txt b/Documentation/networking/device_drivers/ti/cpsw_switchdev.txt new file mode 100644 index 000000000000..5c8cee17fca9 --- /dev/null +++ b/Documentation/networking/device_drivers/ti/cpsw_switchdev.txt @@ -0,0 +1,209 @@ +* Texas Instruments CPSW switchdev based ethernet driver 2.0 + +- Port renaming +On older udev versions renaming of ethX to swXpY will not be automatically +supported +In order to rename via udev: +ip -d link show dev sw0p1 | grep switchid + +SUBSYSTEM=="net", ACTION=="add", ATTR{phys_switch_id}==<switchid>, \ + ATTR{phys_port_name}!="", NAME="sw0$attr{phys_port_name}" + + +==================== +# Dual mac mode +==================== +- The new (cpsw_new.c) driver is operating in dual-emac mode by default, thus +working as 2 individual network interfaces. Main differences from legacy CPSW +driver are: + - optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in +addition to ALLMULTI (current port) instead of ALE_BYPASS. +So, Ports in promiscuous mode will keep possibility of mcast and vlan filtering, +which is provides significant benefits when ports are joined to the same bridge, +but without enabling "switch" mode, or to different bridges. + - learning disabled on ports as it make not too much sense for + segregated ports - no forwarding in HW. + - enabled basic support for devlink. + + devlink dev show + platform/48484000.switch + + devlink dev param show + platform/48484000.switch: + name switch_mode type driver-specific + values: + cmode runtime value false + name ale_bypass type driver-specific + values: + cmode runtime value false + +Devlink configuration parameters +==================== +See Documentation/networking/devlink-params-ti-cpsw-switch.txt + +==================== +# Bridging in dual mac mode +==================== +The dual_mac mode requires two vids to be reserved for internal purposes, +which, by default, equal CPSW Port numbers. As result, bridge has to be +configured in vlan unaware mode or default_pvid has to be adjusted. + + ip link add name br0 type bridge + ip link set dev br0 type bridge vlan_filtering 0 + echo 0 > /sys/class/net/br0/bridge/default_pvid + ip link set dev sw0p1 master br0 + ip link set dev sw0p2 master br0 + - or - + ip link add name br0 type bridge + ip link set dev br0 type bridge vlan_filtering 0 + echo 100 > /sys/class/net/br0/bridge/default_pvid + ip link set dev br0 type bridge vlan_filtering 1 + ip link set dev sw0p1 master br0 + ip link set dev sw0p2 master br0 + +==================== +# Enabling "switch" +==================== +The Switch mode can be enabled by configuring devlink driver parameter +"switch_mode" to 1/true: + devlink dev param set platform/48484000.switch \ + name switch_mode value 1 cmode runtime + +This can be done regardless of the state of Port's netdev devices - UP/DOWN, but +Port's netdev devices have to be in UP before joining to the bridge to avoid +overwriting of bridge configuration as CPSW switch driver copletly reloads its +configuration when first Port changes its state to UP. + +When the both interfaces joined the bridge - CPSW switch driver will enable +marking packets with offload_fwd_mark flag unless "ale_bypass=0" + +All configuration is implemented via switchdev API. + +==================== +# Bridge setup +==================== + devlink dev param set platform/48484000.switch \ + name switch_mode value 1 cmode runtime + + ip link add name br0 type bridge + ip link set dev br0 type bridge ageing_time 1000 + ip link set dev sw0p1 up + ip link set dev sw0p2 up + ip link set dev sw0p1 master br0 + ip link set dev sw0p2 master br0 + [*] bridge vlan add dev br0 vid 1 pvid untagged self + +[*] if vlan_filtering=1. where default_pvid=1 + +================= +# On/off STP +================= +ip link set dev BRDEV type bridge stp_state 1/0 + +Note. Steps [*] are mandatory. + +==================== +# VLAN configuration +==================== +bridge vlan add dev br0 vid 1 pvid untagged self <---- add cpu port to VLAN 1 + +Note. This step is mandatory for bridge/default_pvid. + +================= +# Add extra VLANs +================= + 1. untagged: + bridge vlan add dev sw0p1 vid 100 pvid untagged master + bridge vlan add dev sw0p2 vid 100 pvid untagged master + bridge vlan add dev br0 vid 100 pvid untagged self <---- Add cpu port to VLAN100 + + 2. tagged: + bridge vlan add dev sw0p1 vid 100 master + bridge vlan add dev sw0p2 vid 100 master + bridge vlan add dev br0 vid 100 pvid tagged self <---- Add cpu port to VLAN100 + +==== +FDBs +==== +FDBs are automatically added on the appropriate switch port upon detection + +Manually adding FDBs: +bridge fdb add aa:bb:cc:dd:ee:ff dev sw0p1 master vlan 100 +bridge fdb add aa:bb:cc:dd:ee:fe dev sw0p2 master <---- Add on all VLANs + +==== +MDBs +==== +MDBs are automatically added on the appropriate switch port upon detection + +Manually adding MDBs: +bridge mdb add dev br0 port sw0p1 grp 239.1.1.1 permanent vid 100 +bridge mdb add dev br0 port sw0p1 grp 239.1.1.1 permanent <---- Add on all VLANs + +================== +Multicast flooding +================== +CPU port mcast_flooding is always on + +Turning flooding on/off on swithch ports: +bridge link set dev sw0p1 mcast_flood on/off + +================== +Access and Trunk port +================== + bridge vlan add dev sw0p1 vid 100 pvid untagged master + bridge vlan add dev sw0p2 vid 100 master + + + bridge vlan add dev br0 vid 100 self + ip link add link br0 name br0.100 type vlan id 100 + + Note. Setting PVID on Bridge device itself working only for + default VLAN (default_pvid). + +===================== + NFS +===================== +The only way for NFS to work is by chrooting to a minimal environment when +switch configuration that will affect connectivity is needed. +Assuming you are booting NFS with eth1 interface(the script is hacky and +it's just there to prove NFS is doable). + +setup.sh: +#!/bin/sh +mkdir proc +mount -t proc none /proc +ifconfig br0 > /dev/null +if [ $? -ne 0 ]; then + echo "Setting up bridge" + ip link add name br0 type bridge + ip link set dev br0 type bridge ageing_time 1000 + ip link set dev br0 type bridge vlan_filtering 1 + + ip link set eth1 down + ip link set eth1 name sw0p1 + ip link set dev sw0p1 up + ip link set dev sw0p2 up + ip link set dev sw0p2 master br0 + ip link set dev sw0p1 master br0 + bridge vlan add dev br0 vid 1 pvid untagged self + ifconfig sw0p1 0.0.0.0 + udhchc -i br0 +fi +umount /proc + +run_nfs.sh: +#!/bin/sh +mkdir /tmp/root/bin -p +mkdir /tmp/root/lib -p + +cp -r /lib/ /tmp/root/ +cp -r /bin/ /tmp/root/ +cp /sbin/ip /tmp/root/bin +cp /sbin/bridge /tmp/root/bin +cp /sbin/ifconfig /tmp/root/bin +cp /sbin/udhcpc /tmp/root/bin +cp /path/to/setup.sh /tmp/root/bin +chroot /tmp/root/ busybox sh /bin/setup.sh + +run ./run_nfs.sh diff --git a/Documentation/networking/devlink-params-mlx5.txt b/Documentation/networking/devlink-params-mlx5.txt new file mode 100644 index 000000000000..5071467118bd --- /dev/null +++ b/Documentation/networking/devlink-params-mlx5.txt @@ -0,0 +1,17 @@ +flow_steering_mode [DEVICE, DRIVER-SPECIFIC] + Controls the flow steering mode of the driver. + Two modes are supported: + 1. 'dmfs' - Device managed flow steering. + 2. 'smfs - Software/Driver managed flow steering. + In DMFS mode, the HW steering entities are created and + managed through the Firmware. + In SMFS mode, the HW steering entities are created and + managed though by the driver directly into Hardware + without firmware intervention. + Type: String + Configuration mode: runtime + +enable_roce [DEVICE, GENERIC] + Enable handling of RoCE traffic in the device. + Defaultly enabled. + Configuration mode: driverinit diff --git a/Documentation/networking/devlink-params-mv88e6xxx.txt b/Documentation/networking/devlink-params-mv88e6xxx.txt new file mode 100644 index 000000000000..21c4b3556ef2 --- /dev/null +++ b/Documentation/networking/devlink-params-mv88e6xxx.txt @@ -0,0 +1,7 @@ +ATU_hash [DEVICE, DRIVER-SPECIFIC] + Select one of four possible hashing algorithms for + MAC addresses in the Address Translation Unit. + A value of 3 seems to work better than the default of + 1 when many MAC addresses have the same OUI. + Configuration mode: runtime + Type: u8. 0-3 valid. diff --git a/Documentation/networking/devlink-params-ti-cpsw-switch.txt b/Documentation/networking/devlink-params-ti-cpsw-switch.txt new file mode 100644 index 000000000000..4037458499f7 --- /dev/null +++ b/Documentation/networking/devlink-params-ti-cpsw-switch.txt @@ -0,0 +1,10 @@ +ale_bypass [DEVICE, DRIVER-SPECIFIC] + Allows to enable ALE_CONTROL(4).BYPASS mode for debug purposes. + All packets will be sent to the Host port only if enabled. + Type: bool + Configuration mode: runtime + +switch_mode [DEVICE, DRIVER-SPECIFIC] + Enable switch mode + Type: bool + Configuration mode: runtime diff --git a/Documentation/networking/devlink-params.txt b/Documentation/networking/devlink-params.txt index ddba3e9b55b1..04e234e9acc9 100644 --- a/Documentation/networking/devlink-params.txt +++ b/Documentation/networking/devlink-params.txt @@ -65,3 +65,7 @@ reset_dev_on_drv_probe [DEVICE, GENERIC] Reset only if device firmware can be found in the filesystem. Type: u8 + +enable_roce [DEVICE, GENERIC] + Enable handling of RoCE traffic in the device. + Type: Boolean diff --git a/Documentation/networking/devlink-trap.rst b/Documentation/networking/devlink-trap.rst index 8e90a85f3bd5..dc9659ca06fa 100644 --- a/Documentation/networking/devlink-trap.rst +++ b/Documentation/networking/devlink-trap.rst @@ -162,6 +162,67 @@ be added to the following table: - ``drop`` - Traps packets that the device decided to drop because they could not be enqueued to a transmission queue which is full + * - ``non_ip`` + - ``drop`` + - Traps packets that the device decided to drop because they need to + undergo a layer 3 lookup, but are not IP or MPLS packets + * - ``uc_dip_over_mc_dmac`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and they have a unicast destination IP and a multicast destination + MAC + * - ``dip_is_loopback_address`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and their destination IP is the loopback address (i.e., 127.0.0.0/8 + and ::1/128) + * - ``sip_is_mc`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and their source IP is multicast (i.e., 224.0.0.0/8 and ff::/8) + * - ``sip_is_loopback_address`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and their source IP is the loopback address (i.e., 127.0.0.0/8 and ::1/128) + * - ``ip_header_corrupted`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and their IP header is corrupted: wrong checksum, wrong IP version + or too short Internet Header Length (IHL) + * - ``ipv4_sip_is_limited_bc`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and their source IP is limited broadcast (i.e., 255.255.255.255/32) + * - ``ipv6_mc_dip_reserved_scope`` + - ``drop`` + - Traps IPv6 packets that the device decided to drop because they need to + be routed and their IPv6 multicast destination IP has a reserved scope + (i.e., ffx0::/16) + * - ``ipv6_mc_dip_interface_local_scope`` + - ``drop`` + - Traps IPv6 packets that the device decided to drop because they need to + be routed and their IPv6 multicast destination IP has an interface-local scope + (i.e., ffx1::/16) + * - ``mtu_value_is_too_small`` + - ``exception`` + - Traps packets that should have been routed by the device, but were bigger + than the MTU of the egress interface + * - ``unresolved_neigh`` + - ``exception`` + - Traps packets that did not have a matching IP neighbour after routing + * - ``mc_reverse_path_forwarding`` + - ``exception`` + - Traps multicast IP packets that failed reverse-path forwarding (RPF) + check during multicast routing + * - ``reject_route`` + - ``exception`` + - Traps packets that hit reject routes (i.e., "unreachable", "prohibit") + * - ``ipv4_lpm_miss`` + - ``exception`` + - Traps unicast IPv4 packets that did not match any route + * - ``ipv6_lpm_miss`` + - ``exception`` + - Traps unicast IPv6 packets that did not match any route Driver-specific Packet Traps ============================ diff --git a/Documentation/networking/filter.txt b/Documentation/networking/filter.txt index 319e5e041f38..c4a328f2d57a 100644 --- a/Documentation/networking/filter.txt +++ b/Documentation/networking/filter.txt @@ -770,10 +770,10 @@ Some core changes of the new internal format: callq foo mov %rax,%r13 mov %rbx,%rdi - mov $0x2,%esi - mov $0x3,%edx - mov $0x4,%ecx - mov $0x5,%r8d + mov $0x6,%esi + mov $0x7,%edx + mov $0x8,%ecx + mov $0x9,%r8d callq bar add %r13,%rax mov -0x228(%rbp),%rbx diff --git a/Documentation/networking/index.rst b/Documentation/networking/index.rst index d4dca42910d0..5acab1290e03 100644 --- a/Documentation/networking/index.rst +++ b/Documentation/networking/index.rst @@ -33,6 +33,7 @@ Contents: scaling tls tls-offload + nfc .. only:: subproject and html diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index 8d4ad1d1ae26..099a55bd1432 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -2091,6 +2091,28 @@ pf_enable - INTEGER Default: 1 +pf_expose - INTEGER + Unset or enable/disable pf (pf is short for potentially failed) state + exposure. Applications can control the exposure of the PF path state + in the SCTP_PEER_ADDR_CHANGE event and the SCTP_GET_PEER_ADDR_INFO + sockopt. When it's unset, no SCTP_PEER_ADDR_CHANGE event with + SCTP_ADDR_PF state will be sent and a SCTP_PF-state transport info + can be got via SCTP_GET_PEER_ADDR_INFO sockopt; When it's enabled, + a SCTP_PEER_ADDR_CHANGE event will be sent for a transport becoming + SCTP_PF state and a SCTP_PF-state transport info can be got via + SCTP_GET_PEER_ADDR_INFO sockopt; When it's diabled, no + SCTP_PEER_ADDR_CHANGE event will be sent and it returns -EACCES when + trying to get a SCTP_PF-state transport info via SCTP_GET_PEER_ADDR_INFO + sockopt. + + 0: Unset pf state exposure, Compatible with old applications. + + 1: Disable pf state exposure. + + 2: Enable pf state exposure. + + Default: 0 + addip_noauth_enable - BOOLEAN Dynamic Address Reconfiguration (ADD-IP) requires the use of authentication to protect the operations of adding or removing new @@ -2173,6 +2195,18 @@ pf_retrans - INTEGER Default: 0 +ps_retrans - INTEGER + Primary.Switchover.Max.Retrans (PSMR), it's a tunable parameter coming + from section-5 "Primary Path Switchover" in rfc7829. The primary path + will be changed to another active path when the path error counter on + the old primary path exceeds PSMR, so that "the SCTP sender is allowed + to continue data transmission on a new working path even when the old + primary destination address becomes active again". Note this feature + is disabled by initializing 'ps_retrans' per netns as 0xffff by default, + and its value can't be less than 'pf_retrans' when changing by sysctl. + + Default: 0xffff + rto_initial - INTEGER The initial round trip timeout value in milliseconds that will be used in calculating round trip times. This is the initial time interval diff --git a/Documentation/networking/nfc.txt b/Documentation/networking/nfc.rst index b24c29bdae27..9aab3a88c9b2 100644 --- a/Documentation/networking/nfc.txt +++ b/Documentation/networking/nfc.rst @@ -1,3 +1,4 @@ +=================== Linux NFC subsystem =================== @@ -8,7 +9,7 @@ This document covers the architecture overview, the device driver interface description and the userspace interface description. Architecture overview ---------------------- +===================== The NFC subsystem is responsible for: - NFC adapters management; @@ -25,33 +26,34 @@ The control operations are available to userspace via generic netlink. The low-level data exchange interface is provided by the new socket family PF_NFC. The NFC_SOCKPROTO_RAW performs raw communication with NFC targets. - - +--------------------------------------+ - | USER SPACE | - +--------------------------------------+ - ^ ^ - | low-level | control - | data exchange | operations - | | - | v - | +-----------+ - | AF_NFC | netlink | - | socket +-----------+ - | raw ^ - | | - v v - +---------+ +-----------+ - | rawsock | <--------> | core | - +---------+ +-----------+ - ^ - | - v - +-----------+ - | driver | - +-----------+ +.. code-block:: none + + +--------------------------------------+ + | USER SPACE | + +--------------------------------------+ + ^ ^ + | low-level | control + | data exchange | operations + | | + | v + | +-----------+ + | AF_NFC | netlink | + | socket +-----------+ + | raw ^ + | | + v v + +---------+ +-----------+ + | rawsock | <--------> | core | + +---------+ +-----------+ + ^ + | + v + +-----------+ + | driver | + +-----------+ Device Driver Interface ------------------------ +======================= When registering on the NFC subsystem, the device driver must inform the core of the set of supported NFC protocols and the set of ops callbacks. The ops @@ -64,7 +66,7 @@ callbacks that must be implemented are the following: * data_exchange - send data and receive the response (transceive operation) Userspace interface --------------------- +=================== The userspace interface is divided in control operations and low-level data exchange operation. @@ -82,7 +84,7 @@ The operations are composed by commands and events, all listed below: * NFC_EVENT_DEVICE_ADDED - reports an NFC device addition * NFC_EVENT_DEVICE_REMOVED - reports an NFC device removal * NFC_EVENT_TARGETS_FOUND - reports START_POLL results when 1 or more targets -are found + are found The user must call START_POLL to poll for NFC targets, passing the desired NFC protocols through NFC_ATTR_PROTOCOLS attribute. The device remains in polling @@ -101,14 +103,14 @@ it's closed. LOW-LEVEL DATA EXCHANGE: The userspace must use PF_NFC sockets to perform any data communication with -targets. All NFC sockets use AF_NFC: - -struct sockaddr_nfc { - sa_family_t sa_family; - __u32 dev_idx; - __u32 target_idx; - __u32 nfc_protocol; -}; +targets. All NFC sockets use AF_NFC:: + + struct sockaddr_nfc { + sa_family_t sa_family; + __u32 dev_idx; + __u32 target_idx; + __u32 nfc_protocol; + }; To establish a connection with one target, the user must create an NFC_SOCKPROTO_RAW socket and call the 'connect' syscall with the sockaddr_nfc diff --git a/Documentation/networking/phy.rst b/Documentation/networking/phy.rst index a689966bc4be..cda1c0a0492a 100644 --- a/Documentation/networking/phy.rst +++ b/Documentation/networking/phy.rst @@ -352,7 +352,8 @@ Fills the phydev structure with up-to-date information about the current settings in the PHY. :: - int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd); + int phy_ethtool_ksettings_set(struct phy_device *phydev, + const struct ethtool_link_ksettings *cmd); Ethtool convenience functions. :: diff --git a/Documentation/networking/tls.rst b/Documentation/networking/tls.rst index 5bcbf75e2025..8cb2cd4e2a80 100644 --- a/Documentation/networking/tls.rst +++ b/Documentation/networking/tls.rst @@ -213,3 +213,29 @@ A patchset to OpenSSL to use ktls as the record layer is of calling send directly after a handshake using gnutls. Since it doesn't implement a full record layer, control messages are not supported. + +Statistics +========== + +TLS implementation exposes the following per-namespace statistics +(``/proc/net/tls_stat``): + +- ``TlsCurrTxSw``, ``TlsCurrRxSw`` - + number of TX and RX sessions currently installed where host handles + cryptography + +- ``TlsCurrTxDevice``, ``TlsCurrRxDevice`` - + number of TX and RX sessions currently installed where NIC handles + cryptography + +- ``TlsTxSw``, ``TlsRxSw`` - + number of TX and RX sessions opened with host cryptography + +- ``TlsTxDevice``, ``TlsRxDevice`` - + number of TX and RX sessions opened with NIC cryptography + +- ``TlsDecryptError`` - + record decryption failed (e.g. due to incorrect authentication tag) + +- ``TlsDeviceRxResync`` - + number of RX resyncs sent to NICs handling cryptography diff --git a/Documentation/virt/kvm/api.txt b/Documentation/virt/kvm/api.txt index 4833904d32a5..49183add44e7 100644 --- a/Documentation/virt/kvm/api.txt +++ b/Documentation/virt/kvm/api.txt @@ -1002,12 +1002,18 @@ Specifying exception.has_esr on a system that does not support it will return -EINVAL. Setting anything other than the lower 24bits of exception.serror_esr will return -EINVAL. +It is not possible to read back a pending external abort (injected via +KVM_SET_VCPU_EVENTS or otherwise) because such an exception is always delivered +directly to the virtual CPU). + + struct kvm_vcpu_events { struct { __u8 serror_pending; __u8 serror_has_esr; + __u8 ext_dabt_pending; /* Align it to 8 bytes */ - __u8 pad[6]; + __u8 pad[5]; __u64 serror_esr; } exception; __u32 reserved[12]; @@ -1051,9 +1057,23 @@ contain a valid state and shall be written into the VCPU. ARM/ARM64: +User space may need to inject several types of events to the guest. + Set the pending SError exception state for this VCPU. It is not possible to 'cancel' an Serror that has been made pending. +If the guest performed an access to I/O memory which could not be handled by +userspace, for example because of missing instruction syndrome decode +information or because there is no device mapped at the accessed IPA, then +userspace can ask the kernel to inject an external abort using the address +from the exiting fault on the VCPU. It is a programming error to set +ext_dabt_pending after an exit which was not either KVM_EXIT_MMIO or +KVM_EXIT_ARM_NISV. This feature is only available if the system supports +KVM_CAP_ARM_INJECT_EXT_DABT. This is a helper which provides commonality in +how userspace reports accesses for the above cases to guests, across different +userspace implementations. Nevertheless, userspace can still emulate all Arm +exceptions by manipulating individual registers using the KVM_SET_ONE_REG API. + See KVM_GET_VCPU_EVENTS for the data structure. @@ -2982,6 +3002,9 @@ can be determined by querying the KVM_CAP_GUEST_DEBUG_HW_BPS and KVM_CAP_GUEST_DEBUG_HW_WPS capabilities which return a positive number indicating the number of supported registers. +For ppc, the KVM_CAP_PPC_GUEST_DEBUG_SSTEP capability indicates whether +the single-step debug event (KVM_GUESTDBG_SINGLESTEP) is supported. + When debug events exit the main run loop with the reason KVM_EXIT_DEBUG with the kvm_debug_exit_arch part of the kvm_run structure containing architecture specific debug information. @@ -4468,6 +4491,39 @@ Hyper-V SynIC state change. Notification is used to remap SynIC event/message pages and to enable/disable SynIC messages/events processing in userspace. + /* KVM_EXIT_ARM_NISV */ + struct { + __u64 esr_iss; + __u64 fault_ipa; + } arm_nisv; + +Used on arm and arm64 systems. If a guest accesses memory not in a memslot, +KVM will typically return to userspace and ask it to do MMIO emulation on its +behalf. However, for certain classes of instructions, no instruction decode +(direction, length of memory access) is provided, and fetching and decoding +the instruction from the VM is overly complicated to live in the kernel. + +Historically, when this situation occurred, KVM would print a warning and kill +the VM. KVM assumed that if the guest accessed non-memslot memory, it was +trying to do I/O, which just couldn't be emulated, and the warning message was +phrased accordingly. However, what happened more often was that a guest bug +caused access outside the guest memory areas which should lead to a more +meaningful warning message and an external abort in the guest, if the access +did not fall within an I/O window. + +Userspace implementations can query for KVM_CAP_ARM_NISV_TO_USER, and enable +this capability at VM creation. Once this is done, these types of errors will +instead return to userspace with KVM_EXIT_ARM_NISV, with the valid bits from +the HSR (arm) and ESR_EL2 (arm64) in the esr_iss field, and the faulting IPA +in the fault_ipa field. Userspace can either fix up the access if it's +actually an I/O access by decoding the instruction from guest memory (if it's +very brave) and continue executing the guest, or it can decide to suspend, +dump, or restart the guest. + +Note that KVM does not skip the faulting instruction as it does for +KVM_EXIT_MMIO, but userspace has to emulate any change to the processing state +if it decides to decode and emulate the instruction. + /* Fix the size of the union. */ char padding[256]; }; diff --git a/Documentation/virt/kvm/arm/pvtime.rst b/Documentation/virt/kvm/arm/pvtime.rst new file mode 100644 index 000000000000..2357dd2d8655 --- /dev/null +++ b/Documentation/virt/kvm/arm/pvtime.rst @@ -0,0 +1,80 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Paravirtualized time support for arm64 +====================================== + +Arm specification DEN0057/A defines a standard for paravirtualised time +support for AArch64 guests: + +https://developer.arm.com/docs/den0057/a + +KVM/arm64 implements the stolen time part of this specification by providing +some hypervisor service calls to support a paravirtualized guest obtaining a +view of the amount of time stolen from its execution. + +Two new SMCCC compatible hypercalls are defined: + +* PV_TIME_FEATURES: 0xC5000020 +* PV_TIME_ST: 0xC5000021 + +These are only available in the SMC64/HVC64 calling convention as +paravirtualized time is not available to 32 bit Arm guests. The existence of +the PV_FEATURES hypercall should be probed using the SMCCC 1.1 ARCH_FEATURES +mechanism before calling it. + +PV_TIME_FEATURES + ============= ======== ========== + Function ID: (uint32) 0xC5000020 + PV_call_id: (uint32) The function to query for support. + Currently only PV_TIME_ST is supported. + Return value: (int64) NOT_SUPPORTED (-1) or SUCCESS (0) if the relevant + PV-time feature is supported by the hypervisor. + ============= ======== ========== + +PV_TIME_ST + ============= ======== ========== + Function ID: (uint32) 0xC5000021 + Return value: (int64) IPA of the stolen time data structure for this + VCPU. On failure: + NOT_SUPPORTED (-1) + ============= ======== ========== + +The IPA returned by PV_TIME_ST should be mapped by the guest as normal memory +with inner and outer write back caching attributes, in the inner shareable +domain. A total of 16 bytes from the IPA returned are guaranteed to be +meaningfully filled by the hypervisor (see structure below). + +PV_TIME_ST returns the structure for the calling VCPU. + +Stolen Time +----------- + +The structure pointed to by the PV_TIME_ST hypercall is as follows: + ++-------------+-------------+-------------+----------------------------+ +| Field | Byte Length | Byte Offset | Description | ++=============+=============+=============+============================+ +| Revision | 4 | 0 | Must be 0 for version 1.0 | ++-------------+-------------+-------------+----------------------------+ +| Attributes | 4 | 4 | Must be 0 | ++-------------+-------------+-------------+----------------------------+ +| Stolen time | 8 | 8 | Stolen time in unsigned | +| | | | nanoseconds indicating how | +| | | | much time this VCPU thread | +| | | | was involuntarily not | +| | | | running on a physical CPU. | ++-------------+-------------+-------------+----------------------------+ + +All values in the structure are stored little-endian. + +The structure will be updated by the hypervisor prior to scheduling a VCPU. It +will be present within a reserved region of the normal memory given to the +guest. The guest should not attempt to write into this memory. There is a +structure per VCPU of the guest. + +It is advisable that one or more 64k pages are set aside for the purpose of +these structures and not used for other purposes, this enables the guest to map +the region using 64k pages and avoids conflicting attributes with other memory. + +For the user space interface see Documentation/virt/kvm/devices/vcpu.txt +section "3. GROUP: KVM_ARM_VCPU_PVTIME_CTRL". diff --git a/Documentation/virt/kvm/devices/vcpu.txt b/Documentation/virt/kvm/devices/vcpu.txt index 2b5dab16c4f2..6f3bd64a05b0 100644 --- a/Documentation/virt/kvm/devices/vcpu.txt +++ b/Documentation/virt/kvm/devices/vcpu.txt @@ -60,3 +60,17 @@ time to use the number provided for a given timer, overwriting any previously configured values on other VCPUs. Userspace should configure the interrupt numbers on at least one VCPU after creating all VCPUs and before running any VCPUs. + +3. GROUP: KVM_ARM_VCPU_PVTIME_CTRL +Architectures: ARM64 + +3.1 ATTRIBUTE: KVM_ARM_VCPU_PVTIME_IPA +Parameters: 64-bit base address +Returns: -ENXIO: Stolen time not implemented + -EEXIST: Base address already set for this VCPU + -EINVAL: Base address not 64 byte aligned + +Specifies the base address of the stolen time structure for this VCPU. The +base address must be 64 byte aligned and exist within a valid guest memory +region. See Documentation/virt/kvm/arm/pvtime.txt for more information +including the layout of the stolen time structure. diff --git a/Documentation/virt/kvm/devices/xics.txt b/Documentation/virt/kvm/devices/xics.txt index 42864935ac5d..423332dda7bc 100644 --- a/Documentation/virt/kvm/devices/xics.txt +++ b/Documentation/virt/kvm/devices/xics.txt @@ -3,9 +3,19 @@ XICS interrupt controller Device type supported: KVM_DEV_TYPE_XICS Groups: - KVM_DEV_XICS_SOURCES + 1. KVM_DEV_XICS_GRP_SOURCES Attributes: One per interrupt source, indexed by the source number. + 2. KVM_DEV_XICS_GRP_CTRL + Attributes: + 2.1 KVM_DEV_XICS_NR_SERVERS (write only) + The kvm_device_attr.addr points to a __u32 value which is the number of + interrupt server numbers (ie, highest possible vcpu id plus one). + Errors: + -EINVAL: Value greater than KVM_MAX_VCPU_ID. + -EFAULT: Invalid user pointer for attr->addr. + -EBUSY: A vcpu is already connected to the device. + This device emulates the XICS (eXternal Interrupt Controller Specification) defined in PAPR. The XICS has a set of interrupt sources, each identified by a 20-bit source number, and a set of @@ -38,7 +48,7 @@ least-significant end of the word: Each source has 64 bits of state that can be read and written using the KVM_GET_DEVICE_ATTR and KVM_SET_DEVICE_ATTR ioctls, specifying the -KVM_DEV_XICS_SOURCES attribute group, with the attribute number being +KVM_DEV_XICS_GRP_SOURCES attribute group, with the attribute number being the interrupt source number. The 64 bit state word has the following bitfields, starting from the least-significant end of the word: diff --git a/Documentation/virt/kvm/devices/xive.txt b/Documentation/virt/kvm/devices/xive.txt index 9a24a4525253..f5d1d6b5af61 100644 --- a/Documentation/virt/kvm/devices/xive.txt +++ b/Documentation/virt/kvm/devices/xive.txt @@ -78,6 +78,14 @@ the legacy interrupt mode, referred as XICS (POWER7/8). migrating the VM. Errors: none + 1.3 KVM_DEV_XIVE_NR_SERVERS (write only) + The kvm_device_attr.addr points to a __u32 value which is the number of + interrupt server numbers (ie, highest possible vcpu id plus one). + Errors: + -EINVAL: Value greater than KVM_MAX_VCPU_ID. + -EFAULT: Invalid user pointer for attr->addr. + -EBUSY: A vCPU is already connected to the device. + 2. KVM_DEV_XIVE_GRP_SOURCE (write only) Initializes a new source in the XIVE device and mask it. Attributes: |