diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/clock/silabs,si5351.txt | 4 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt (renamed from Documentation/devicetree/bindings/mtd/m25p80.txt) | 6 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/net/cdns-emac.txt | 3 | ||||
| -rw-r--r-- | Documentation/serial/tty.txt | 3 | ||||
| -rw-r--r-- | Documentation/virtual/kvm/mmu.txt | 18 |
5 files changed, 25 insertions, 9 deletions
diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt index c40711e8e8f7..28b28309f535 100644 --- a/Documentation/devicetree/bindings/clock/silabs,si5351.txt +++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt @@ -17,7 +17,8 @@ Required properties: - #clock-cells: from common clock binding; shall be set to 1. - clocks: from common clock binding; list of parent clock handles, shall be xtal reference clock or xtal and clkin for - si5351c only. + si5351c only. Corresponding clock input names are "xtal" and + "clkin" respectively. - #address-cells: shall be set to 1. - #size-cells: shall be set to 0. @@ -71,6 +72,7 @@ i2c-master-node { /* connect xtal input to 25MHz reference */ clocks = <&ref25>; + clock-names = "xtal"; /* connect xtal input as source of pll0 and pll1 */ silabs,pll-source = <0 0>, <1 0>; diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt index f20b111b502a..2bee68103b01 100644 --- a/Documentation/devicetree/bindings/mtd/m25p80.txt +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt @@ -8,8 +8,8 @@ Required properties: is not Linux-only, but in case of Linux, see the "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of supported chips. - Must also include "nor-jedec" for any SPI NOR flash that can be - identified by the JEDEC READ ID opcode (0x9F). + Must also include "jedec,spi-nor" for any SPI NOR flash that can + be identified by the JEDEC READ ID opcode (0x9F). - reg : Chip-Select number - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at @@ -25,7 +25,7 @@ Example: flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "spansion,m25p80", "nor-jedec"; + compatible = "spansion,m25p80", "jedec,spi-nor"; reg = <0>; spi-max-frequency = <40000000>; m25p,fast-read; diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt index abd67c13d344..4451ee973223 100644 --- a/Documentation/devicetree/bindings/net/cdns-emac.txt +++ b/Documentation/devicetree/bindings/net/cdns-emac.txt @@ -3,7 +3,8 @@ Required properties: - compatible: Should be "cdns,[<chip>-]{emac}" Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. - or the generic form: "cdns,emac". + Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. + Or the generic form: "cdns,emac". - reg: Address and length of the register set for the device - interrupts: Should contain macb interrupt - phy-mode: see ethernet.txt file in the same directory. diff --git a/Documentation/serial/tty.txt b/Documentation/serial/tty.txt index 1e52d67d0abf..dbe6623fed1c 100644 --- a/Documentation/serial/tty.txt +++ b/Documentation/serial/tty.txt @@ -198,6 +198,9 @@ TTY_IO_ERROR If set, causes all subsequent userspace read/write TTY_OTHER_CLOSED Device is a pty and the other side has closed. +TTY_OTHER_DONE Device is a pty and the other side has closed and + all pending input processing has been completed. + TTY_NO_WRITE_SPLIT Prevent driver from splitting up writes into smaller chunks. diff --git a/Documentation/virtual/kvm/mmu.txt b/Documentation/virtual/kvm/mmu.txt index 53838d9c6295..c59bd9bc41ef 100644 --- a/Documentation/virtual/kvm/mmu.txt +++ b/Documentation/virtual/kvm/mmu.txt @@ -169,6 +169,10 @@ Shadow pages contain the following information: Contains the value of cr4.smep && !cr0.wp for which the page is valid (pages for which this is true are different from other pages; see the treatment of cr0.wp=0 below). + role.smap_andnot_wp: + Contains the value of cr4.smap && !cr0.wp for which the page is valid + (pages for which this is true are different from other pages; see the + treatment of cr0.wp=0 below). gfn: Either the guest page table containing the translations shadowed by this page, or the base page frame for linear translations. See role.direct. @@ -344,10 +348,16 @@ on fault type: (user write faults generate a #PF) -In the first case there is an additional complication if CR4.SMEP is -enabled: since we've turned the page into a kernel page, the kernel may now -execute it. We handle this by also setting spte.nx. If we get a user -fetch or read fault, we'll change spte.u=1 and spte.nx=gpte.nx back. +In the first case there are two additional complications: +- if CR4.SMEP is enabled: since we've turned the page into a kernel page, + the kernel may now execute it. We handle this by also setting spte.nx. + If we get a user fetch or read fault, we'll change spte.u=1 and + spte.nx=gpte.nx back. +- if CR4.SMAP is disabled: since the page has been changed to a kernel + page, it can not be reused when CR4.SMAP is enabled. We set + CR4.SMAP && !CR0.WP into shadow page's role to avoid this case. Note, + here we do not care the case that CR4.SMAP is enabled since KVM will + directly inject #PF to guest due to failed permission check. To prevent an spte that was converted into a kernel page with cr0.wp=0 from being written by the kernel after cr0.wp has changed to 1, we make |