diff options
Diffstat (limited to 'arch/arm/boot/dts/gemini-dlink-dir-685.dts')
-rw-r--r-- | arch/arm/boot/dts/gemini-dlink-dir-685.dts | 79 |
1 files changed, 51 insertions, 28 deletions
diff --git a/arch/arm/boot/dts/gemini-dlink-dir-685.dts b/arch/arm/boot/dts/gemini-dlink-dir-685.dts index e2030ba16512..396149664297 100644 --- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts +++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts @@ -61,9 +61,9 @@ #size-cells = <0>; /* Collides with IDE pins, that's cool (we do not use them) */ - gpio-sck = <&gpio1 5 GPIO_ACTIVE_HIGH>; - gpio-miso = <&gpio1 8 GPIO_ACTIVE_HIGH>; - gpio-mosi = <&gpio1 7 GPIO_ACTIVE_HIGH>; + sck-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + miso-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; num-chipselects = <1>; @@ -119,13 +119,11 @@ /* * This is a Sunon Maglev GM0502PFV2-8 cooling fan @10000 RPM. - * Since the platform has no temperature sensor, this is controlled - * from userspace by using the hard disks S.M.A.R.T. temperature * sensor. It is turned on when the temperature exceeds 46 degrees * and turned off when the temperatures goes below 41 degrees * (celsius). */ - gpio-fan { + fan0: gpio-fan { compatible = "gpio-fan"; /* Collides with IDE */ gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; @@ -133,11 +131,45 @@ #cooling-cells = <2>; }; + thermal-zones { + chassis-thermal { + /* Poll every 20 seconds */ + polling-delay = <20000>; + /* Poll every 2nd second when cooling */ + polling-delay-passive = <2000>; + /* Use the thermal sensor in the hard drive */ + thermal-sensors = <&drive0>; + + /* Tripping points from the fan.script in the rootfs */ + trips { + alert: chassis-alert { + /* At 43 degrees turn on the fan */ + temperature = <43000>; + hysteresis = <3000>; + type = "active"; + }; + crit: chassis-crit { + /* Just shut down at 60 degrees */ + temperature = <60000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&alert>; + cooling-device = <&fan0 1 1>; + }; + }; + }; + }; + /* * The touchpad input is connected to a GPIO bit-banged * I2C bus. */ - gpio-i2c { + i2c { compatible = "i2c-gpio"; /* Collides with ICE */ sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; @@ -407,24 +439,6 @@ pci@50000000 { status = "okay"; - interrupt-map-mask = <0xf800 0 0 7>; - interrupt-map = - <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */ - <0x4800 0 0 2 &pci_intc 1>, - <0x4800 0 0 3 &pci_intc 2>, - <0x4800 0 0 4 &pci_intc 3>, - <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */ - <0x5000 0 0 2 &pci_intc 2>, - <0x5000 0 0 3 &pci_intc 3>, - <0x5000 0 0 4 &pci_intc 0>, - <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */ - <0x5800 0 0 2 &pci_intc 3>, - <0x5800 0 0 3 &pci_intc 0>, - <0x5800 0 0 4 &pci_intc 1>, - <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */ - <0x6000 0 0 2 &pci_intc 0>, - <0x6000 0 0 3 &pci_intc 1>, - <0x6000 0 0 4 &pci_intc 2>; }; ethernet@60000000 { @@ -443,15 +457,24 @@ }; }; - ata@63000000 { + ide@63000000 { status = "okay"; + + /* + * This drive may have a temperature sensor with a + * thermal zone we can use for thermal control of the + * chassis temperature using the fan. + */ + drive0: ide-port@0 { + reg = <0>; + #thermal-sensor-cells = <0>; + }; }; display-controller@6a000000 { status = "okay"; - port@0 { - reg = <0>; + port { display_out: endpoint { remote-endpoint = <&panel_in>; }; |