diff options
Diffstat (limited to 'arch/arm/boot/dts/r7s9210-rza2mevb.dts')
| -rw-r--r-- | arch/arm/boot/dts/r7s9210-rza2mevb.dts | 80 |
1 files changed, 55 insertions, 25 deletions
diff --git a/arch/arm/boot/dts/r7s9210-rza2mevb.dts b/arch/arm/boot/dts/r7s9210-rza2mevb.dts index d062d02865e7..69a5a44b8a2f 100644 --- a/arch/arm/boot/dts/r7s9210-rza2mevb.dts +++ b/arch/arm/boot/dts/r7s9210-rza2mevb.dts @@ -4,6 +4,28 @@ * * Copyright (C) 2018 Renesas Electronics * + * As upstream Linux does not support XIP, it cannot run in 8 MiB of HyperRAM. + * Hence the 64 MiB of SDRAM on the sub-board needs to be enabled, which has + * the following ramifications: + * - SCIF4 connected to the on-board USB-serial can no longer be used as the + * serial console, + * - Instead, SCIF2 is used as the serial console, by connecting a 3.3V TTL + * USB-to-Serial adapter to the CMOS camera connector: + * - RXD = CN17-9, + * - TXD = CN17-10, + * - GND = CN17-2 or CN17-17, + * - The first Ethernet channel can no longer be used, + * - USB Channel 1 loses the overcurrent input signal. + * + * Please make sure your sub-board matches the following switch settings: + * + * SW6 SW6-1 set to SDRAM + * ON SW6-2 set to Audio + * +---------------------+ SW6-3 set to DRP + * | = = = = = | SW6-4 set to CEU + * | = = | SW6-5 set to Ether2 + * | 1 2 3 4 5 6 7 8 9 0 | SW6-6 set to VDC6 + * +---------------------+ SW6-7 set to VDC6 */ /dts-v1/; @@ -17,9 +39,8 @@ compatible = "renesas,rza2mevb", "renesas,r7s9210"; aliases { - serial0 = &scif4; - ethernet0 = ðer0; - ethernet1 = ðer1; + serial0 = &scif2; + ethernet0 = ðer1; }; chosen { @@ -50,17 +71,17 @@ leds { compatible = "gpio-leds"; - red { + led-red { gpios = <&pinctrl RZA2_PIN(PORT6, 0) GPIO_ACTIVE_HIGH>; }; - green { + led-green { gpios = <&pinctrl RZA2_PIN(PORTC, 1) GPIO_ACTIVE_HIGH>; }; }; - memory@40000000 { + memory@c000000 { device_type = "memory"; - reg = <0x40000000 0x00800000>; /* HyperRAM */ + reg = <0x0c000000 0x04000000>; /* SDRAM */ }; }; @@ -72,17 +93,6 @@ status = "okay"; }; -ðer0 { - pinctrl-names = "default"; - pinctrl-0 = <ð0_pins>; - status = "okay"; - renesas,no-ether-link; - phy-handle = <&phy0>; - phy0: ethernet-phy@0 { - reg = <0>; - }; -}; - ðer1 { pinctrl-names = "default"; pinctrl-0 = <ð1_pins>; @@ -90,6 +100,8 @@ renesas,no-ether-link; phy-handle = <&phy1>; phy1: ethernet-phy@1 { + compatible = "ethernet-phy-id001c.c816", + "ethernet-phy-ieee802.3-c22"; reg = <0>; }; }; @@ -99,6 +111,20 @@ clock-frequency = <24000000>; /* 24MHz */ }; +&i2c3 { + status = "okay"; + clock-frequency = <400000>; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + + eeprom@50 { + compatible = "renesas,r1ex24128", "atmel,24c128"; + reg = <0x50>; + pagesize = <64>; + }; +}; + /* High resolution System tick timers */ &ostm0 { status = "okay"; @@ -137,14 +163,19 @@ <RZA2_PINMUX(PORTL, 1, 5)>; /* IRQ5 */ }; + i2c3_pins: i2c3 { + pinmux = <RZA2_PINMUX(PORTD, 6, 1)>, /* RIIC3SCL */ + <RZA2_PINMUX(PORTD, 7, 1)>; /* RIIC3SDA */ + }; + keyboard_pins: keyboard { pinmux = <RZA2_PINMUX(PORTJ, 1, 6)>; /* IRQ0 */ }; /* Serial Console */ - scif4_pins: serial4 { - pinmux = <RZA2_PINMUX(PORT9, 0, 4)>, /* TxD4 */ - <RZA2_PINMUX(PORT9, 1, 4)>; /* RxD4 */ + scif2_pins: serial2 { + pinmux = <RZA2_PINMUX(PORTE, 2, 3)>, /* TxD2 */ + <RZA2_PINMUX(PORTE, 1, 3)>; /* RxD2 */ }; sdhi0_pins: sdhi0 { @@ -165,8 +196,7 @@ usb1_pins: usb1 { pinmux = <RZA2_PINMUX(PORTC, 0, 1)>, /* VBUSIN1 */ - <RZA2_PINMUX(PORTC, 5, 1)>, /* VBUSEN1 */ - <RZA2_PINMUX(PORT7, 5, 5)>; /* OVRCUR1 */ + <RZA2_PINMUX(PORTC, 5, 1)>; /* VBUSEN1 */ }; }; @@ -176,9 +206,9 @@ }; /* Serial Console */ -&scif4 { +&scif2 { pinctrl-names = "default"; - pinctrl-0 = <&scif4_pins>; + pinctrl-0 = <&scif2_pins>; status = "okay"; }; |