diff options
Diffstat (limited to 'arch/arm/boot/dts/ste-href-tvk1281618.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 71 |
1 files changed, 2 insertions, 69 deletions
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi index 3bafd26b4824..e1dbfae22595 100644 --- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi +++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi @@ -2,7 +2,7 @@ /* * Copyright 2012 ST-Ericsson AB * - * Device Tree for the TVK1281618 UIB + * Device Tree for the TVK1281618 family of UIBs */ #include <dt-bindings/interrupt-controller/irq.h> @@ -81,62 +81,8 @@ }; }; }; - /* Sensors mounted on this board variant */ + /* Sensors mounted on all board variants */ i2c@80128000 { - lsm303dlh@18 { - /* Accelerometer */ - compatible = "st,lsm303dlh-accel"; - st,drdy-int-pin = <1>; - drive-open-drain; - reg = <0x18>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&accel_tvk_mode>; - /* - * These interrupts cannot be used: the other component - * ST-Micro L3D4200D gyro that is connected to the same lines - * cannot set its DRDY line to open drain, so it cannot be - * shared with other peripherals. The should be defined for - * the falling edge if they could be wired together. - * - * interrupts-extended = - * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, - * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; - */ - }; - lsm303dlh@1e { - /* Magnetometer */ - compatible = "st,lsm303dlh-magn"; - reg = <0x1e>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - /* - * These interrupts cannot be used: the other component - * ST-Micro L3D4200D gyro that is connected to the same lines - * cannot set its DRDY line to open drain, so it cannot be - * shared with other peripherals. The should be defined for - * the falling edge if they could be wired together. - * - * interrupts-extended = - * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, - * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; - */ - }; - lis331dl@1c { - /* Accelerometer */ - compatible = "st,lis331dl-accel"; - st,drdy-int-pin = <1>; - reg = <0x1c>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&accel_tvk_mode>; - interrupt-parent = <&gpio2>; - /* INT2 would need to be open drain */ - interrupts = <18 IRQ_TYPE_EDGE_RISING>, - <19 IRQ_TYPE_EDGE_RISING>; - }; ak8974@f { /* Magnetometer */ compatible = "asahi-kasei,ak8974"; @@ -268,18 +214,5 @@ }; }; }; - - mcde@a0350000 { - status = "okay"; - - dsi@a0351000 { - panel { - compatible = "samsung,s6d16d0"; - reg = <0>; - vdd1-supply = <&ab8500_ldo_aux1_reg>; - reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; - }; - }; - }; }; }; |