diff options
Diffstat (limited to 'arch/arm/boot/dts/ste-ux500-samsung-gavini.dts')
| -rw-r--r-- | arch/arm/boot/dts/ste-ux500-samsung-gavini.dts | 77 |
1 files changed, 53 insertions, 24 deletions
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts b/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts index 47bbf5ab267f..7231bc745200 100644 --- a/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts +++ b/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts @@ -24,6 +24,32 @@ compatible = "samsung,eb585157lu"; }; + thermal-zones { + battery-thermal { + /* This zone will be polled by the battery temperature code */ + polling-delay = <0>; + polling-delay-passive = <0>; + thermal-sensors = <&bat_therm>; + + trips { + battery-crit-hi { + temperature = <70000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; + + bat_therm: thermistor { + compatible = "samsung,1404-001221"; + io-channels = <&gpadc 0x02>; /* BatTemp */ + pullup-uv = <1800000>; + pullup-ohm = <230000>; + pulldown-ohm = <0>; + #thermal-sensor-cells = <0>; + }; + /* TI TXS0206 level translator for 2.9 V */ sd_level_translator: regulator-gpio { compatible = "regulator-fixed"; @@ -232,19 +258,18 @@ #address-cells = <1>; #size-cells = <0>; - /* TODO: Memsic MMC328 magnetometer */ - magnetometer@30 { - compatible = "memsic,mmc328"; - reg = <0x30>; - /* TODO: if you have the schematic, check if both voltages come from AUX2 */ - /* VDA 1.8 V */ - vda-supply = <&ab8500_ldo_aux2_reg>; - /* VDD 1.8V */ - vdd-supply = <&ab8500_ldo_aux2_reg>; - /* GPIO204 */ + /* Yamaha YAS530 magnetometer */ + magnetometer@2e { + compatible = "yamaha,yas530"; + reg = <0x2e>; + /* VDD 3V */ + vdd-supply = <&ab8500_ldo_aux1_reg>; + /* IOVDD 1.8V */ + iovdd-supply = <&ab8500_ldo_aux2_reg>; + /* GPIO204 COMPASS_RST_N */ reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; - pinctrl-0 = <&mmc328_default>; + pinctrl-0 = <&yas530_default>; }; /* TODO: this should also be used by the NCP6914 Camera power management unit */ }; @@ -433,13 +458,17 @@ prcmu@80157000 { ab8500 { - ab8500_usb { + phy { pinctrl-names = "default", "sleep"; pinctrl-0 = <&usb_a_1_default>; pinctrl-1 = <&usb_a_1_sleep>; }; - ab8500-regulators { + ab8500_fg { + line-impedance-micro-ohms = <43000>; + }; + + regulator { ab8500_ldo_aux1 { /* Used for VDD for sensors */ regulator-name = "V-SENSORS-VDD"; @@ -506,8 +535,8 @@ accelerometer@18 { compatible = "bosch,bma222e"; reg = <0x18>; - mount-matrix = "0", "1", "0", - "-1", "0", "0", + mount-matrix = "0", "-1", "0", + "1", "0", "0", "0", "0", "1"; vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V @@ -645,6 +674,15 @@ }; }; }; + /* Reset line for the Yamaha YAS530 magnetometer */ + yas530 { + yas530_default: yas530_janice { + janice_cfg1 { + pins = "GPIO204_AF23"; + ste,config = <&gpio_out_hi>; + }; + }; + }; /* Flash and torch */ flash { gpio_flash_default_mode: flash_default { @@ -747,15 +785,6 @@ }; }; }; - /* Reset line for the Memsic MMC328 magnetometer */ - mmc328 { - mmc328_default: mmc328_gavini { - gavini_cfg1 { - pins = "GPIO204_AF23"; - ste,config = <&gpio_out_hi>; - }; - }; - }; /* Interrupt line for Invensense MPU3050 gyroscope */ mpu3050 { mpu3050_default: mpu3050 { |