diff options
Diffstat (limited to 'arch/arm/boot/dts/ste-ux500-samsung-golden.dts')
-rw-r--r-- | arch/arm/boot/dts/ste-ux500-samsung-golden.dts | 294 |
1 files changed, 286 insertions, 8 deletions
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts index 313f0ab16866..9604695edf53 100644 --- a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts +++ b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts @@ -5,6 +5,7 @@ #include "ste-ab8505.dtsi" #include "ste-dbx5x0-pinctrl.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> #include <dt-bindings/input/input.h> #include <dt-bindings/interrupt-controller/irq.h> @@ -24,9 +25,85 @@ stdout-path = &serial2; }; + battery: battery { + compatible = "samsung,eb-l1m7flu"; + }; + + thermal-zones { + battery-thermal { + /* This zone will be polled by the battery temperature code */ + polling-delay = <0>; + polling-delay-passive = <0>; + thermal-sensors = <&bat_therm>; + + trips { + battery-crit-hi { + temperature = <70000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; + + bat_therm: thermistor { + compatible = "samsung,1404-001221"; + io-channels = <&gpadc 0x02>; /* BatTemp */ + pullup-uv = <1800000>; + pullup-ohm = <230000>; + pulldown-ohm = <0>; + #thermal-sensor-cells = <0>; + }; + + i2c-gpio-0 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio2 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio2 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_0_default>; + + #address-cells = <1>; + #size-cells = <0>; + + touchkey@20 { + compatible = "coreriver,tc360-touchkey"; + reg = <0x20>; + vdd-supply = <&ab8500_ldo_aux4_reg>; + vcc-supply = <&ab8500_ldo_aux6_reg>; + + interrupt-parent = <&gpio2>; + interrupts = <15 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&touchkey_default>; + linux,keycodes = <KEY_MENU KEY_BACK>; + }; + }; + + i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_1_default>; + + #address-cells = <1>; + #size-cells = <0>; + + magnetometer@c { + compatible = "alps,hscdtd008a"; + reg = <0x0c>; + + avdd-supply = <&ab8500_ldo_aux1_reg>; + dvdd-supply = <&ab8500_ldo_aux8_reg>; + }; + }; + soc { /* External Micro SD card slot */ - sdi0_per1@80126000 { + mmc@80126000 { status = "okay"; arm,primecell-periphid = <0x10480180>; @@ -54,7 +131,7 @@ }; /* WLAN SDIO */ - sdi1_per2@80118000 { + mmc@80118000 { status = "okay"; arm,primecell-periphid = <0x10480180>; @@ -74,7 +151,7 @@ #size-cells = <0>; wifi@1 { - compatible = "brcm,bcm4329-fmac"; + compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac"; reg = <1>; /* GPIO216 (WLAN_HOST_WAKE) */ @@ -88,7 +165,7 @@ }; /* eMMC */ - sdi2_per3@80005000 { + mmc@80005000 { status = "okay"; arm,primecell-periphid = <0x10480180>; @@ -98,6 +175,8 @@ non-removable; cap-mmc-highspeed; mmc-ddr-1_8v; + no-sdio; + no-sd; vmmc-supply = <&vmem_3v3>; @@ -115,6 +194,7 @@ pinctrl-1 = <&u0_a_1_sleep>; bluetooth { + /* BCM4334B0 actually */ compatible = "brcm,bcm4330-bt"; /* GPIO222 (BT_VREG_ON) */ shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; @@ -146,6 +226,32 @@ pinctrl-1 = <&u2rxtx_c_1_sleep>; }; + i2c@80004000 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c0_a_1_default>; + pinctrl-1 = <&i2c0_a_1_sleep>; + + proximity@44 { + compatible = "sharp,gp2ap002s00f"; + reg = <0x44>; + + /* GPIO146 (PS_INT) */ + interrupt-parent = <&gpio4>; + interrupts = <18 IRQ_TYPE_EDGE_FALLING>; + + vdd-supply = <&ab8500_ldo_aux1_reg>; + vio-supply = <&ab8500_ldo_aux8_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&proximity_default>; + + sharp,proximity-far-hysteresis = <0x40>; + sharp,proximity-close-hysteresis = <0x0f>; + }; + }; + i2c@80128000 { status = "okay"; @@ -188,6 +294,11 @@ interrupt-parent = <&gpio6>; interrupts = <26 IRQ_TYPE_EDGE_FALLING>; + /* VDDA is "analog supply", 2.57-3.47 V */ + vdda-supply = <&ab8500_ldo_aux2_reg>; + /* VDD is "digital supply" 1.71-3.47V */ + vdd-supply = <&ab8500_ldo_aux5_reg>; + pinctrl-names = "default"; pinctrl-0 = <&tsp_default>; }; @@ -195,13 +306,17 @@ prcmu@80157000 { ab8505 { - ab8500_usb { + phy { pinctrl-names = "default", "sleep"; pinctrl-0 = <&usb_a_1_default>; pinctrl-1 = <&usb_a_1_sleep>; }; - ab8505-regulators { + ab8500_fg { + line-impedance-micro-ohms = <36000>; + }; + + regulator { ab8500_ldo_aux1 { regulator-name = "sensor_3v"; regulator-min-microvolt = <3000000>; @@ -212,7 +327,6 @@ regulator-name = "vreg_tsp_a3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - regulator-always-on; /* FIXME */ }; ab8500_ldo_aux3 { @@ -229,7 +343,6 @@ regulator-name = "vreg_tsp_1v8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - regulator-always-on; /* FIXME */ }; ab8500_ldo_aux6 { @@ -244,6 +357,29 @@ }; }; }; + + mcde@a0350000 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dsi_default_mode>; + + dsi@a0351000 { + panel@0 { + compatible = "samsung,s6e63m0"; + reg = <0>; + max-brightness = <15>; + vdd3-supply = <&panel_reg_3v0>; + vci-supply = <&panel_reg_1v8>; + reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; + /* ESD (electrostatic discharge) detection interrupt */ + interrupt-parent = <&gpio2>; + interrupts = <18 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "esd"; + pinctrl-names = "default"; + pinctrl-0 = <&display_default_mode>; + }; + }; + }; }; gpio-keys { @@ -276,6 +412,32 @@ }; }; + /* Richtek RT8515GQW Flash LED Driver IC */ + flash { + compatible = "richtek,rt8515"; + /* GPIO 140 */ + enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; + /* GPIO 141 */ + ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; + /* + * RFS is 16 kOhm and RTS is 100 kOhm giving + * the flash max current 343mA and torch max + * current 55 mA. + */ + richtek,rfs-ohms = <16000>; + richtek,rts-ohms = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_flash_default_mode>; + + led { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; + flash-max-timeout-us = <250000>; + flash-max-microamp = <343750>; + led-max-microamp = <55000>; + }; + }; + vibrator { compatible = "gpio-vibrator"; /* GPIO195 (MOT_EN) */ @@ -343,6 +505,40 @@ pinctrl-names = "default"; pinctrl-0 = <&wlan_en_default>; }; + + /* MIC5366 GPIO-controlled regulator */ + panel_reg_1v8: regulator-panel-1v8 { + compatible = "regulator-fixed"; + + regulator-name = "panel-fixed-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + /* GPIO219 */ + gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; + + startup-delay-us = <200>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_reg_default_mode>; + }; + + /* MIC5366 GPIO-controlled regulator */ + panel_reg_3v0: regulator-panel-3v0 { + compatible = "regulator-fixed"; + + regulator-name = "panel-fixed-supply"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + /* GPIO219 */ + gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; + + startup-delay-us = <200>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_reg_default_mode>; + }; }; &pinctrl { @@ -357,6 +553,44 @@ }; }; + i2c-gpio-0 { + i2c_gpio_0_default: i2c_gpio_0 { + golden_cfg1 { + pins = "GPIO77", /* TOUCHKEY_SCL */ + "GPIO78"; /* TOUCHKEY_SDA */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + + flash { + gpio_flash_default_mode: flash_default { + golden_cfg1 { + pins = "GPIO140_B11", "GPIO141_C12"; + ste,config = <&gpio_out_lo>; + }; + }; + }; + + i2c-gpio-1 { + i2c_gpio_1_default: i2c_gpio_1 { + golden_cfg1 { + pins = "GPIO151", /* COMP_SCL */ + "GPIO152"; /* COMP_SDA */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + + touchkey { + touchkey_default: touchkey_default { + golden_cfg1 { + pins = "GPIO79"; /* TOUCHKEY_INT */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + sdi0 { sd_level_translator_default: sd_level_translator_default { golden_cfg1 { @@ -375,6 +609,50 @@ }; }; + mcde { + dsi_default_mode: dsi_default { + default_mux1 { + /* Mux in VSI0 used for DSI TE */ + function = "lcd"; + groups = + "lcdvsi0_a_1"; /* VSI0 for LCD */ + }; + default_cfg1 { + pins = + "GPIO68_E1"; /* VSI0 */ + ste,config = <&in_nopull>; + }; + }; + }; + + display { + display_default_mode: display_default { + golden_cfg1 { + pins = "GPIO139_C9"; /* MIPI_DSI0_RESET_N */ + ste,config = <&gpio_out_lo>; + }; + golden_cfg2 { + pins = "GPIO82_C1"; /* LDI_ESD_DET */ + ste,config = <&gpio_in_pu>; + }; + }; + panel_reg_default_mode: panel_reg_default { + golden_cfg1 { + pins = "GPIO219_AG10"; /* LCD_PWR_EN */ + ste,config = <&gpio_out_lo>; + }; + }; + }; + + proximity { + proximity_default: proximity_default { + golden_cfg1 { + pins = "GPIO146_D13"; /* PS_INT */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + imu { imu_default: imu_default { golden_cfg1 { |