diff options
Diffstat (limited to 'arch/arm/boot/dts/stm32mp157c-ev1.dts')
| -rw-r--r-- | arch/arm/boot/dts/stm32mp157c-ev1.dts | 93 |
1 files changed, 68 insertions, 25 deletions
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts index 228e35e16884..050c3c27a420 100644 --- a/arch/arm/boot/dts/stm32mp157c-ev1.dts +++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts @@ -19,6 +19,7 @@ aliases { serial0 = &uart4; + serial1 = &usart3; ethernet0 = ðernet0; }; @@ -89,6 +90,7 @@ port { dcmi_0: endpoint { remote-endpoint = <&ov5640_0>; + bus-type = <5>; bus-width = <8>; hsync-active = <0>; vsync-active = <0>; @@ -98,15 +100,10 @@ }; &dsi { - #address-cells = <1>; - #size-cells = <0>; phy-dsi-supply = <®18>; status = "okay"; ports { - #address-cells = <1>; - #size-cells = <0>; - port@0 { reg = <0>; dsi_in: endpoint { @@ -141,7 +138,7 @@ ðernet0 { status = "okay"; pinctrl-0 = <ðernet0_rgmii_pins_a>; - pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>; + pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>; pinctrl-names = "default", "sleep"; phy-mode = "rgmii-id"; max-speed = <1000>; @@ -162,20 +159,23 @@ pinctrl-0 = <&fmc_pins_a>; pinctrl-1 = <&fmc_sleep_pins_a>; status = "okay"; - #address-cells = <1>; - #size-cells = <0>; - nand@0 { - reg = <0>; - nand-on-flash-bbt; - #address-cells = <1>; - #size-cells = <1>; + nand-controller@4,0 { + status = "okay"; + + nand@0 { + reg = <0>; + nand-on-flash-bbt; + #address-cells = <1>; + #size-cells = <1>; + }; }; }; &i2c2 { - pinctrl-names = "default"; + pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c2_pins_a>; + pinctrl-1 = <&i2c2_sleep_pins_a>; i2c-scl-rising-time-ns = <185>; i2c-scl-falling-time-ns = <20>; status = "okay"; @@ -210,7 +210,7 @@ interrupt-parent = <&gpioi>; vdd-supply = <&v3v3>; - stmfx_pinctrl: stmfx-pin-controller { + stmfx_pinctrl: pinctrl { compatible = "st,stmfx-0300-pinctrl"; gpio-controller; #gpio-cells = <2>; @@ -218,7 +218,7 @@ #interrupt-cells = <2>; gpio-ranges = <&stmfx_pinctrl 0 0 24>; - joystick_pins: joystick { + joystick_pins: joystick-pins { pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4"; bias-pull-down; }; @@ -227,8 +227,9 @@ }; &i2c5 { - pinctrl-names = "default"; + pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c5_pins_a>; + pinctrl-1 = <&i2c5_sleep_pins_a>; i2c-scl-rising-time-ns = <185>; i2c-scl-falling-time-ns = <20>; status = "okay"; @@ -238,9 +239,6 @@ status = "okay"; port { - #address-cells = <1>; - #size-cells = <0>; - ltdc_ep0_out: endpoint@0 { reg = <0>; remote-endpoint = <&dsi_in>; @@ -257,14 +255,22 @@ &qspi { pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>; - pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>; + pinctrl-0 = <&qspi_clk_pins_a + &qspi_bk1_pins_a + &qspi_cs1_pins_a + &qspi_bk2_pins_a + &qspi_cs2_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a + &qspi_bk1_sleep_pins_a + &qspi_cs1_sleep_pins_a + &qspi_bk2_sleep_pins_a + &qspi_cs2_sleep_pins_a>; reg = <0x58003000 0x1000>, <0x70000000 0x4000000>; #address-cells = <1>; #size-cells = <0>; status = "okay"; - flash0: mx66l51235l@0 { + flash0: flash@0 { compatible = "jedec,spi-nor"; reg = <0>; spi-rx-bus-width = <4>; @@ -273,7 +279,7 @@ #size-cells = <1>; }; - flash1: mx66l51235l@1 { + flash1: flash@1 { compatible = "jedec,spi-nor"; reg = <1>; spi-rx-bus-width = <4>; @@ -347,13 +353,28 @@ }; }; +&usart3 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&usart3_pins_b>; + pinctrl-1 = <&usart3_sleep_pins_b>; + pinctrl-2 = <&usart3_idle_pins_b>; + /* + * HW flow control USART3_RTS is optional, and isn't default wired to + * the connector. SB23 needs to be soldered in order to use it, and R77 + * (ETH_CLK) should be removed. + */ + uart-has-rtscts; + status = "disabled"; +}; + &usbh_ehci { phys = <&usbphyc_port0>; status = "okay"; }; &usbotg_hs { - dr_mode = "peripheral"; + pinctrl-0 = <&usbotg_hs_pins_a>; + pinctrl-names = "default"; phys = <&usbphyc_port1 0>; phy-names = "usb2-phy"; status = "okay"; @@ -362,3 +383,25 @@ &usbphyc { status = "okay"; }; + +&usbphyc_port0 { + st,tune-hs-dc-level = <2>; + st,enable-fs-rftime-tuning; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <15>; + st,trim-hs-impedance = <1>; + st,tune-squelch-level = <3>; + st,tune-hs-rx-offset = <2>; + st,no-lsfs-sc; +}; + +&usbphyc_port1 { + st,tune-hs-dc-level = <2>; + st,enable-fs-rftime-tuning; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <15>; + st,trim-hs-impedance = <1>; + st,tune-squelch-level = <3>; + st,tune-hs-rx-offset = <2>; + st,no-lsfs-sc; +}; |