diff options
Diffstat (limited to 'arch/arm/mach-omap1/board-osk.c')
| -rw-r--r-- | arch/arm/mach-omap1/board-osk.c | 49 |
1 files changed, 38 insertions, 11 deletions
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c index e18b6f13300e..76684b7a4e87 100644 --- a/arch/arm/mach-omap1/board-osk.c +++ b/arch/arm/mach-omap1/board-osk.c @@ -42,18 +42,17 @@ #include <linux/mfd/tps65010.h> #include <linux/platform_data/gpio-omap.h> #include <linux/platform_data/omap1_bl.h> +#include <linux/soc/ti/omap1-io.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> +#include "tc.h" #include "flash.h" -#include <mach/mux.h> -#include <mach/tc.h> - -#include <mach/hardware.h> -#include <mach/usb.h> - +#include "mux.h" +#include "hardware.h" +#include "usb.h" #include "common.h" /* Name of the GPIO chip used by the OMAP for GPIOs 0..15 */ @@ -153,14 +152,14 @@ static struct resource osk5912_cf_resources[] = { [0] = { .flags = IORESOURCE_IRQ, }, + [1] = { + .flags = IORESOURCE_MEM, + }, }; static struct platform_device osk5912_cf_device = { .name = "omap_cf", .id = -1, - .dev = { - .platform_data = (void *) 2 /* CS2 */, - }, .num_resources = ARRAY_SIZE(osk5912_cf_resources), .resource = osk5912_cf_resources, }; @@ -275,13 +274,41 @@ static void __init osk_init_smc91x(void) omap_writel(l, EMIFS_CCS(1)); } -static void __init osk_init_cf(void) +static void __init osk_init_cf(int seg) { + struct resource *res = &osk5912_cf_resources[1]; + omap_cfg_reg(M7_1610_GPIO62); if ((gpio_request(62, "cf_irq")) < 0) { printk("Error requesting gpio 62 for CF irq\n"); return; } + + switch (seg) { + /* NOTE: CS0 could be configured too ... */ + case 1: + res->start = OMAP_CS1_PHYS; + break; + case 2: + res->start = OMAP_CS2_PHYS; + break; + case 3: + res->start = omap_cs3_phys(); + break; + } + + res->end = res->start + SZ_8K - 1; + osk5912_cf_device.dev.platform_data = (void *)(uintptr_t)seg; + + /* NOTE: better EMIFS setup might support more cards; but the + * TRM only shows how to affect regular flash signals, not their + * CF/PCMCIA variants... + */ + pr_debug("%s: cs%d, previous ccs %08x acs %08x\n", __func__, + seg, omap_readl(EMIFS_CCS(seg)), omap_readl(EMIFS_ACS(seg))); + omap_writel(0x0004a1b3, EMIFS_CCS(seg)); /* synch mode 4 etc */ + omap_writel(0x00000000, EMIFS_ACS(seg)); /* OE hold/setup */ + /* the CF I/O IRQ is really active-low */ irq_set_irq_type(gpio_to_irq(62), IRQ_TYPE_EDGE_FALLING); } @@ -580,7 +607,7 @@ static void __init osk_init(void) u32 l; osk_init_smc91x(); - osk_init_cf(); + osk_init_cf(2); /* CS2 */ /* Workaround for wrong CS3 (NOR flash) timing * There are some U-Boot versions out there which configure |