diff options
Diffstat (limited to 'arch/arm/mach-omap1/devices.c')
| -rw-r--r-- | arch/arm/mach-omap1/devices.c | 351 |
1 files changed, 351 insertions, 0 deletions
diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c new file mode 100644 index 000000000000..3c5d901efeaa --- /dev/null +++ b/arch/arm/mach-omap1/devices.c @@ -0,0 +1,351 @@ +/* + * linux/arch/arm/mach-omap1/devices.c + * + * OMAP1 platform device setup/initialization + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/config.h> +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> + +#include <asm/hardware.h> +#include <asm/io.h> +#include <asm/mach-types.h> +#include <asm/mach/map.h> + +#include <asm/arch/tc.h> +#include <asm/arch/board.h> +#include <asm/arch/mux.h> +#include <asm/arch/gpio.h> + + +static void omap_nop_release(struct device *dev) +{ + /* Nothing */ +} + +/*-------------------------------------------------------------------------*/ + +#if defined(CONFIG_I2C_OMAP) || defined(CONFIG_I2C_OMAP_MODULE) + +#define OMAP_I2C_BASE 0xfffb3800 + +static struct resource i2c_resources[] = { + { + .start = OMAP_I2C_BASE, + .end = OMAP_I2C_BASE + 0x3f, + .flags = IORESOURCE_MEM, + }, + { + .start = INT_I2C, + .flags = IORESOURCE_IRQ, + }, +}; + +/* DMA not used; works around erratum writing to non-empty i2c fifo */ + +static struct platform_device omap_i2c_device = { + .name = "i2c_omap", + .id = -1, + .dev = { + .release = omap_nop_release, + }, + .num_resources = ARRAY_SIZE(i2c_resources), + .resource = i2c_resources, +}; + +static void omap_init_i2c(void) +{ + /* FIXME define and use a boot tag, in case of boards that + * either don't wire up I2C, or chips that mux it differently... + * it can include clocking and address info, maybe more. + */ + omap_cfg_reg(I2C_SCL); + omap_cfg_reg(I2C_SDA); + + (void) platform_device_register(&omap_i2c_device); +} +#else +static inline void omap_init_i2c(void) {} +#endif + +/*-------------------------------------------------------------------------*/ + +#if defined(CONFIG_OMAP1610_IR) || defined(CONFIG_OMAP161O_IR_MODULE) + +static u64 irda_dmamask = 0xffffffff; + +static struct platform_device omap1610ir_device = { + .name = "omap1610-ir", + .id = -1, + .dev = { + .release = omap_nop_release, + .dma_mask = &irda_dmamask, + }, +}; + +static void omap_init_irda(void) +{ + /* FIXME define and use a boot tag, members something like: + * u8 uart; // uart1, or uart3 + * ... but driver only handles uart3 for now + * s16 fir_sel; // gpio for SIR vs FIR + * ... may prefer a callback for SIR/MIR/FIR mode select; + * while h2 uses a GPIO, H3 uses a gpio expander + */ + if (machine_is_omap_h2() + || machine_is_omap_h3()) + (void) platform_device_register(&omap1610ir_device); +} +#else +static inline void omap_init_irda(void) {} +#endif + +/*-------------------------------------------------------------------------*/ + +#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) + +#define OMAP_MMC1_BASE 0xfffb7800 +#define OMAP_MMC2_BASE 0xfffb7c00 /* omap16xx only */ + +static struct omap_mmc_conf mmc1_conf; + +static u64 mmc1_dmamask = 0xffffffff; + +static struct resource mmc1_resources[] = { + { + .start = IO_ADDRESS(OMAP_MMC1_BASE), + .end = IO_ADDRESS(OMAP_MMC1_BASE) + 0x7f, + .flags = IORESOURCE_MEM, + }, + { + .start = INT_MMC, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mmc_omap_device1 = { + .name = "mmci-omap", + .id = 1, + .dev = { + .release = omap_nop_release, + .dma_mask = &mmc1_dmamask, + .platform_data = &mmc1_conf, + }, + .num_resources = ARRAY_SIZE(mmc1_resources), + .resource = mmc1_resources, +}; + +#ifdef CONFIG_ARCH_OMAP16XX + +static struct omap_mmc_conf mmc2_conf; + +static u64 mmc2_dmamask = 0xffffffff; + +static struct resource mmc2_resources[] = { + { + .start = IO_ADDRESS(OMAP_MMC2_BASE), + .end = IO_ADDRESS(OMAP_MMC2_BASE) + 0x7f, + .flags = IORESOURCE_MEM, + }, + { + .start = INT_1610_MMC2, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mmc_omap_device2 = { + .name = "mmci-omap", + .id = 2, + .dev = { + .release = omap_nop_release, + .dma_mask = &mmc2_dmamask, + .platform_data = &mmc2_conf, + }, + .num_resources = ARRAY_SIZE(mmc2_resources), + .resource = mmc2_resources, +}; +#endif + +static void __init omap_init_mmc(void) +{ + const struct omap_mmc_config *mmc_conf; + const struct omap_mmc_conf *mmc; + + /* NOTE: assumes MMC was never (wrongly) enabled */ + mmc_conf = omap_get_config(OMAP_TAG_MMC, struct omap_mmc_config); + if (!mmc_conf) + return; + + /* block 1 is always available and has just one pinout option */ + mmc = &mmc_conf->mmc[0]; + if (mmc->enabled) { + omap_cfg_reg(MMC_CMD); + omap_cfg_reg(MMC_CLK); + omap_cfg_reg(MMC_DAT0); + if (cpu_is_omap1710()) { + omap_cfg_reg(M15_1710_MMC_CLKI); + omap_cfg_reg(P19_1710_MMC_CMDDIR); + omap_cfg_reg(P20_1710_MMC_DATDIR0); + } + if (mmc->wire4) { + omap_cfg_reg(MMC_DAT1); + /* NOTE: DAT2 can be on W10 (here) or M15 */ + if (!mmc->nomux) + omap_cfg_reg(MMC_DAT2); + omap_cfg_reg(MMC_DAT3); + } + mmc1_conf = *mmc; + (void) platform_device_register(&mmc_omap_device1); + } + +#ifdef CONFIG_ARCH_OMAP16XX + /* block 2 is on newer chips, and has many pinout options */ + mmc = &mmc_conf->mmc[1]; + if (mmc->enabled) { + if (!mmc->nomux) { + omap_cfg_reg(Y8_1610_MMC2_CMD); + omap_cfg_reg(Y10_1610_MMC2_CLK); + omap_cfg_reg(R18_1610_MMC2_CLKIN); + omap_cfg_reg(W8_1610_MMC2_DAT0); + if (mmc->wire4) { + omap_cfg_reg(V8_1610_MMC2_DAT1); + omap_cfg_reg(W15_1610_MMC2_DAT2); + omap_cfg_reg(R10_1610_MMC2_DAT3); + } + + /* These are needed for the level shifter */ + omap_cfg_reg(V9_1610_MMC2_CMDDIR); + omap_cfg_reg(V5_1610_MMC2_DATDIR0); + omap_cfg_reg(W19_1610_MMC2_DATDIR1); + } + + /* Feedback clock must be set on OMAP-1710 MMC2 */ + if (cpu_is_omap1710()) + omap_writel(omap_readl(MOD_CONF_CTRL_1) | (1 << 24), + MOD_CONF_CTRL_1); + mmc2_conf = *mmc; + (void) platform_device_register(&mmc_omap_device2); + } +#endif + return; +} +#else +static inline void omap_init_mmc(void) {} +#endif + +#if defined(CONFIG_OMAP_RTC) || defined(CONFIG_OMAP_RTC) + +#define OMAP_RTC_BASE 0xfffb4800 + +static struct resource rtc_resources[] = { + { + .start = OMAP_RTC_BASE, + .end = OMAP_RTC_BASE + 0x5f, + .flags = IORESOURCE_MEM, + }, + { + .start = INT_RTC_TIMER, + .flags = IORESOURCE_IRQ, + }, + { + .start = INT_RTC_ALARM, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device omap_rtc_device = { + .name = "omap_rtc", + .id = -1, + .dev = { + .release = omap_nop_release, + }, + .num_resources = ARRAY_SIZE(rtc_resources), + .resource = rtc_resources, +}; + +static void omap_init_rtc(void) +{ + (void) platform_device_register(&omap_rtc_device); +} +#else +static inline void omap_init_rtc(void) {} +#endif + +/*-------------------------------------------------------------------------*/ + +#if defined(CONFIG_OMAP16XX_WATCHDOG) || defined(CONFIG_OMAP16XX_WATCHDOG_MODULE) + +#define OMAP_WDT_BASE 0xfffeb000 + +static struct resource wdt_resources[] = { + { + .start = OMAP_WDT_BASE, + .end = OMAP_WDT_BASE + 0x4f, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device omap_wdt_device = { + .name = "omap1610_wdt", + .id = -1, + .dev = { + .release = omap_nop_release, + }, + .num_resources = ARRAY_SIZE(wdt_resources), + .resource = wdt_resources, +}; + +static void omap_init_wdt(void) +{ + (void) platform_device_register(&omap_wdt_device); +} +#else +static inline void omap_init_wdt(void) {} +#endif + + +/*-------------------------------------------------------------------------*/ + +/* + * This gets called after board-specific INIT_MACHINE, and initializes most + * on-chip peripherals accessible on this board (except for few like USB): + * + * (a) Does any "standard config" pin muxing needed. Board-specific + * code will have muxed GPIO pins and done "nonstandard" setup; + * that code could live in the boot loader. + * (b) Populating board-specific platform_data with the data drivers + * rely on to handle wiring variations. + * (c) Creating platform devices as meaningful on this board and + * with this kernel configuration. + * + * Claiming GPIOs, and setting their direction and initial values, is the + * responsibility of the device drivers. So is responding to probe(). + * + * Board-specific knowlege like creating devices or pin setup is to be + * kept out of drivers as much as possible. In particular, pin setup + * may be handled by the boot loader, and drivers should expect it will + * normally have been done by the time they're probed. + */ +static int __init omap_init_devices(void) +{ + /* please keep these calls, and their implementations above, + * in alphabetical order so they're easier to sort through. + */ + omap_init_i2c(); + omap_init_irda(); + omap_init_mmc(); + omap_init_rtc(); + omap_init_wdt(); + + return 0; +} +arch_initcall(omap_init_devices); + |