diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi')
| -rw-r--r-- | arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi | 424 |
1 files changed, 295 insertions, 129 deletions
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi index bd1eb3eeca53..3255bd3fcb55 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi @@ -1,10 +1,10 @@ // SPDX-License-Identifier: GPL-2.0-only -#include "msm8916.dtsi" -#include "pm8916.dtsi" +#include "msm8916-pm8916.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> #include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> / { aliases { @@ -15,81 +15,12 @@ stdout-path = "serial0"; }; - soc { - sdhci@7824000 { - status = "okay"; - - vmmc-supply = <&pm8916_l8>; - vqmmc-supply = <&pm8916_l5>; - - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; - pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; - }; - - sdhci@7864000 { - status = "okay"; - - vmmc-supply = <&pm8916_l11>; - vqmmc-supply = <&pm8916_l12>; - - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; - pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; - - cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; - }; - - serial@78b0000 { - status = "okay"; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&blsp1_uart2_default>; - pinctrl-1 = <&blsp1_uart2_sleep>; - }; - - usb@78d9000 { - status = "okay"; - extcon = <&muic>, <&muic>; - - hnp-disable; - srp-disable; - adp-disable; - - ulpi { - phy { - extcon = <&muic>; - v1p8-supply = <&pm8916_l7>; - v3p3-supply = <&pm8916_l13>; - }; - }; - }; - - wcnss@a21b000 { - status = "okay"; + reserved-memory { + /* Additional memory used by Samsung firmware modifications */ + tz-apps@85500000 { + reg = <0x0 0x85500000 0x0 0xb00000>; + no-map; }; - - /* - * Attempting to enable these devices causes a "synchronous - * external abort". Suspected cause is that the debug power - * domain is not enabled by default on this device. - * Disable these devices for now to avoid the crash. - * - * See: https://lore.kernel.org/linux-arm-msm/20190618202623.GA53651@gerhold.net/ - */ - tpiu@820000 { status = "disabled"; }; - funnel@821000 { status = "disabled"; }; - replicator@824000 { status = "disabled"; }; - etf@825000 { status = "disabled"; }; - etr@826000 { status = "disabled"; }; - funnel@841000 { status = "disabled"; }; - debug@850000 { status = "disabled"; }; - debug@852000 { status = "disabled"; }; - debug@854000 { status = "disabled"; }; - debug@856000 { status = "disabled"; }; - etm@85c000 { status = "disabled"; }; - etm@85d000 { status = "disabled"; }; - etm@85e000 { status = "disabled"; }; - etm@85f000 { status = "disabled"; }; }; gpio-keys { @@ -100,13 +31,13 @@ label = "GPIO Buttons"; - volume-up { + button-volume-up { label = "Volume Up"; gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; linux,code = <KEY_VOLUMEUP>; }; - home { + button-home { label = "Home"; gpios = <&msmgpio 109 GPIO_ACTIVE_LOW>; linux,code = <KEY_HOMEPAGE>; @@ -121,7 +52,7 @@ label = "GPIO Hall Effect Sensor"; - hall-sensor { + event-hall-sensor { label = "Hall Effect Sensor"; gpios = <&msmgpio 52 GPIO_ACTIVE_LOW>; linux,input-type = <EV_SW>; @@ -130,15 +61,31 @@ }; }; + reg_vdd_tsp_a: regulator-vdd-tsp-a { + compatible = "regulator-fixed"; + regulator-name = "vdd_tsp_a"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&msmgpio 73 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&tsp_en_default>; + }; + i2c-muic { compatible = "i2c-gpio"; sda-gpios = <&msmgpio 105 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; scl-gpios = <&msmgpio 106 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + pinctrl-names = "default"; + pinctrl-0 = <&muic_i2c_default>; + #address-cells = <1>; #size-cells = <0>; - muic: sm5502@25 { + muic: extcon@25 { compatible = "siliconmitus,sm5502-muic"; reg = <0x25>; @@ -149,44 +96,152 @@ pinctrl-0 = <&muic_int_default>; }; }; -}; -&msmgpio { - gpio_keys_default: gpio_keys_default { - pinmux { - function = "gpio"; - pins = "gpio107", "gpio109"; - }; - pinconf { - pins = "gpio107", "gpio109"; - drive-strength = <2>; - bias-pull-up; + i2c-tkey { + compatible = "i2c-gpio"; + sda-gpios = <&msmgpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&msmgpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + + pinctrl-names = "default"; + pinctrl-0 = <&tkey_i2c_default>; + + #address-cells = <1>; + #size-cells = <0>; + + touchkey: touchkey@20 { + /* Note: Actually an ABOV MCU that implements same interface */ + compatible = "coreriver,tc360-touchkey"; + reg = <0x20>; + + interrupt-parent = <&msmgpio>; + interrupts = <98 IRQ_TYPE_EDGE_FALLING>; + + /* vcc/vdd-supply are board-specific */ + vddio-supply = <&pm8916_l6>; + + linux,keycodes = <KEY_APPSELECT KEY_BACK>; + + pinctrl-names = "default"; + pinctrl-0 = <&tkey_default>; }; }; - gpio_hall_sensor_default: gpio_hall_sensor_default { - pinmux { - function = "gpio"; - pins = "gpio52"; - }; - pinconf { - pins = "gpio52"; - drive-strength = <2>; - bias-disable; + i2c-nfc { + compatible = "i2c-gpio"; + sda-gpios = <&msmgpio 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&msmgpio 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + + pinctrl-names = "default"; + pinctrl-0 = <&nfc_i2c_default>; + + #address-cells = <1>; + #size-cells = <0>; + + nfc@27 { + compatible = "samsung,s3fwrn5-i2c"; + reg = <0x27>; + + interrupt-parent = <&msmgpio>; + interrupts = <21 IRQ_TYPE_EDGE_RISING>; + + en-gpios = <&msmgpio 20 GPIO_ACTIVE_HIGH>; + wake-gpios = <&msmgpio 49 GPIO_ACTIVE_HIGH>; + + clocks = <&rpmcc RPM_SMD_BB_CLK2_PIN>; + + pinctrl-names = "default"; + pinctrl-0 = <&nfc_default &nfc_clk_req>; }; }; +}; - muic_int_default: muic_int_default { - pinmux { - function = "gpio"; - pins = "gpio12"; - }; - pinconf { - pins = "gpio12"; - drive-strength = <2>; - bias-disable; - }; +&blsp_i2c2 { + status = "okay"; + + accelerometer: accelerometer@10 { + compatible = "bosch,bmc150_accel"; + reg = <0x10>; + interrupt-parent = <&msmgpio>; + interrupts = <115 IRQ_TYPE_EDGE_RISING>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; + + pinctrl-names = "default"; + pinctrl-0 = <&accel_int_default>; }; + + magnetometer@12 { + compatible = "bosch,bmc150_magn"; + reg = <0x12>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; + }; +}; + +&blsp_i2c4 { + status = "okay"; + + battery@35 { + compatible = "richtek,rt5033-battery"; + reg = <0x35>; + interrupt-parent = <&msmgpio>; + interrupts = <121 IRQ_TYPE_EDGE_BOTH>; + + pinctrl-names = "default"; + pinctrl-0 = <&fg_alert_default>; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&dsi0 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mdss_default>; + pinctrl-1 = <&mdss_sleep>; +}; + +&mdss { + status = "okay"; +}; + +&pm8916_resin { + status = "okay"; + linux,code = <KEY_VOLUMEDOWN>; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; + + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; +}; + +&usb { + status = "okay"; + extcon = <&muic>, <&muic>; +}; + +&usb_hs_phy { + extcon = <&muic>; }; &smd_rpm_regulators { @@ -194,11 +249,6 @@ vdd_l4_l5_l6-supply = <&pm8916_s4>; vdd_l7-supply = <&pm8916_s4>; - s1 { - regulator-min-microvolt = <500000>; - regulator-max-microvolt = <1300000>; - }; - s3 { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1300000>; @@ -219,11 +269,6 @@ regulator-max-microvolt = <1200000>; }; - l3 { - regulator-min-microvolt = <500000>; - regulator-max-microvolt = <1287500>; - }; - l4 { regulator-min-microvolt = <2050000>; regulator-max-microvolt = <2050000>; @@ -302,15 +347,136 @@ }; }; -&spmi_bus { - pm8916@0 { - pon@800 { - volume-down { - compatible = "qcom,pm8941-resin"; - interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; - bias-pull-up; - linux,code = <KEY_VOLUMEDOWN>; - }; +&msmgpio { + accel_int_default: accel-int-default { + pins = "gpio115"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + fg_alert_default: fg-alert-default { + pins = "gpio121"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + gpio_keys_default: gpio-keys-default { + pins = "gpio107", "gpio109"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + gpio_hall_sensor_default: gpio-hall-sensor-default { + pins = "gpio52"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + mdss { + mdss_default: mdss-default { + pins = "gpio25"; + function = "gpio"; + + drive-strength = <8>; + bias-disable; + }; + mdss_sleep: mdss-sleep { + pins = "gpio25"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-down; + }; + }; + + muic_i2c_default: muic-i2c-default { + pins = "gpio105", "gpio106"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + muic_int_default: muic-int-default { + pins = "gpio12"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + nfc_default: nfc-default { + pins = "gpio20", "gpio49"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + + irq { + pins = "gpio21"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-down; }; }; + + nfc_i2c_default: nfc-i2c-default { + pins = "gpio0", "gpio1"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + tkey_default: tkey-default { + pins = "gpio98"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + tkey_i2c_default: tkey-i2c-default { + pins = "gpio16", "gpio17"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + tsp_en_default: tsp-en-default { + pins = "gpio73"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + ts_int_default: ts-int-default { + pins = "gpio13"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; +}; + +&pm8916_gpios { + nfc_clk_req: nfc-clk-req-state { + pins = "gpio2"; + function = "func1"; + + input-enable; + bias-disable; + power-source = <PM8916_GPIO_L2>; + }; }; |