aboutsummaryrefslogtreecommitdiffstats
path: root/arch/ppc/syslib/ppc83xx_setup.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/ppc/syslib/ppc83xx_setup.c')
-rw-r--r--arch/ppc/syslib/ppc83xx_setup.c251
1 files changed, 250 insertions, 1 deletions
diff --git a/arch/ppc/syslib/ppc83xx_setup.c b/arch/ppc/syslib/ppc83xx_setup.c
index 602a86891f7f..4da168a6ad03 100644
--- a/arch/ppc/syslib/ppc83xx_setup.c
+++ b/arch/ppc/syslib/ppc83xx_setup.c
@@ -11,6 +11,17 @@
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * Added PCI support -- Tony Li <tony.li@freescale.com>
*/
#include <linux/config.h>
@@ -29,8 +40,13 @@
#include <asm/ppc_sys.h>
#include <asm/kgdb.h>
#include <asm/delay.h>
+#include <asm/machdep.h>
#include <syslib/ppc83xx_setup.h>
+#if defined(CONFIG_PCI)
+#include <asm/delay.h>
+#include <syslib/ppc83xx_pci.h>
+#endif
phys_addr_t immrbar;
@@ -162,4 +178,237 @@ mpc83xx_halt(void)
for(;;);
}
-/* PCI SUPPORT DOES NOT EXIT, MODEL after ppc85xx_setup.c */
+#if defined(CONFIG_PCI)
+void __init
+mpc83xx_setup_pci1(struct pci_controller *hose)
+{
+ u16 reg16;
+ volatile immr_pcictrl_t * pci_ctrl;
+ volatile immr_ios_t * ios;
+ bd_t *binfo = (bd_t *) __res;
+
+ pci_ctrl = ioremap(binfo->bi_immr_base + 0x8500, sizeof(immr_pcictrl_t));
+ ios = ioremap(binfo->bi_immr_base + 0x8400, sizeof(immr_ios_t));
+
+ /*
+ * Configure PCI Outbound Translation Windows
+ */
+ ios->potar0 = (MPC83xx_PCI1_LOWER_MEM >> 12) & POTAR_TA_MASK;
+ ios->pobar0 = (MPC83xx_PCI1_LOWER_MEM >> 12) & POBAR_BA_MASK;
+ ios->pocmr0 = POCMR_EN |
+ (((0xffffffff - (MPC83xx_PCI1_UPPER_MEM -
+ MPC83xx_PCI1_LOWER_MEM)) >> 12) & POCMR_CM_MASK);
+
+ /* mapped to PCI1 IO space */
+ ios->potar1 = (MPC83xx_PCI1_LOWER_IO >> 12) & POTAR_TA_MASK;
+ ios->pobar1 = (MPC83xx_PCI1_IO_BASE >> 12) & POBAR_BA_MASK;
+ ios->pocmr1 = POCMR_EN | POCMR_IO |
+ (((0xffffffff - (MPC83xx_PCI1_UPPER_IO -
+ MPC83xx_PCI1_LOWER_IO)) >> 12) & POCMR_CM_MASK);
+
+ /*
+ * Configure PCI Inbound Translation Windows
+ */
+ pci_ctrl->pitar1 = 0x0;
+ pci_ctrl->pibar1 = 0x0;
+ pci_ctrl->piebar1 = 0x0;
+ pci_ctrl->piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP | PIWAR_IWS_2G;
+
+ /*
+ * Release PCI RST signal
+ */
+ pci_ctrl->gcr = 0;
+ udelay(2000);
+ pci_ctrl->gcr = 1;
+ udelay(2000);
+
+ reg16 = 0xff;
+ early_read_config_word(hose, hose->first_busno, 0, PCI_COMMAND, &reg16);
+ reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ early_write_config_word(hose, hose->first_busno, 0, PCI_COMMAND, reg16);
+
+ /*
+ * Clear non-reserved bits in status register.
+ */
+ early_write_config_word(hose, hose->first_busno, 0, PCI_STATUS, 0xffff);
+ early_write_config_byte(hose, hose->first_busno, 0, PCI_LATENCY_TIMER, 0x80);
+
+ iounmap(pci_ctrl);
+ iounmap(ios);
+}
+
+void __init
+mpc83xx_setup_pci2(struct pci_controller *hose)
+{
+ u16 reg16;
+ volatile immr_pcictrl_t * pci_ctrl;
+ volatile immr_ios_t * ios;
+ bd_t *binfo = (bd_t *) __res;
+
+ pci_ctrl = ioremap(binfo->bi_immr_base + 0x8600, sizeof(immr_pcictrl_t));
+ ios = ioremap(binfo->bi_immr_base + 0x8400, sizeof(immr_ios_t));
+
+ /*
+ * Configure PCI Outbound Translation Windows
+ */
+ ios->potar3 = (MPC83xx_PCI2_LOWER_MEM >> 12) & POTAR_TA_MASK;
+ ios->pobar3 = (MPC83xx_PCI2_LOWER_MEM >> 12) & POBAR_BA_MASK;
+ ios->pocmr3 = POCMR_EN | POCMR_DST |
+ (((0xffffffff - (MPC83xx_PCI2_UPPER_MEM -
+ MPC83xx_PCI2_LOWER_MEM)) >> 12) & POCMR_CM_MASK);
+
+ /* mapped to PCI2 IO space */
+ ios->potar4 = (MPC83xx_PCI2_LOWER_IO >> 12) & POTAR_TA_MASK;
+ ios->pobar4 = (MPC83xx_PCI2_IO_BASE >> 12) & POBAR_BA_MASK;
+ ios->pocmr4 = POCMR_EN | POCMR_DST | POCMR_IO |
+ (((0xffffffff - (MPC83xx_PCI2_UPPER_IO -
+ MPC83xx_PCI2_LOWER_IO)) >> 12) & POCMR_CM_MASK);
+
+ /*
+ * Configure PCI Inbound Translation Windows
+ */
+ pci_ctrl->pitar1 = 0x0;
+ pci_ctrl->pibar1 = 0x0;
+ pci_ctrl->piebar1 = 0x0;
+ pci_ctrl->piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP | PIWAR_IWS_2G;
+
+ /*
+ * Release PCI RST signal
+ */
+ pci_ctrl->gcr = 0;
+ udelay(2000);
+ pci_ctrl->gcr = 1;
+ udelay(2000);
+
+ reg16 = 0xff;
+ early_read_config_word(hose, hose->first_busno, 0, PCI_COMMAND, &reg16);
+ reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ early_write_config_word(hose, hose->first_busno, 0, PCI_COMMAND, reg16);
+
+ /*
+ * Clear non-reserved bits in status register.
+ */
+ early_write_config_word(hose, hose->first_busno, 0, PCI_STATUS, 0xffff);
+ early_write_config_byte(hose, hose->first_busno, 0, PCI_LATENCY_TIMER, 0x80);
+
+ iounmap(pci_ctrl);
+ iounmap(ios);
+}
+
+/*
+ * PCI buses can be enabled only if SYS board combinates with PIB
+ * (Platform IO Board) board which provide 3 PCI slots. There is 2 PCI buses
+ * and 3 PCI slots, so people must configure the routes between them before
+ * enable PCI bus. This routes are under the control of PCA9555PW device which
+ * can be accessed via I2C bus 2 and are configured by firmware. Refer to
+ * Freescale to get more information about firmware configuration.
+ */
+
+extern int mpc83xx_exclude_device(u_char bus, u_char devfn);
+extern int mpc83xx_map_irq(struct pci_dev *dev, unsigned char idsel,
+ unsigned char pin);
+void __init
+mpc83xx_setup_hose(void)
+{
+ u32 val32;
+ volatile immr_clk_t * clk;
+ struct pci_controller * hose1;
+#ifdef CONFIG_MPC83xx_PCI2
+ struct pci_controller * hose2;
+#endif
+ bd_t * binfo = (bd_t *)__res;
+
+ clk = ioremap(binfo->bi_immr_base + 0xA00,
+ sizeof(immr_clk_t));
+
+ /*
+ * Configure PCI controller and PCI_CLK_OUTPUT both in 66M mode
+ */
+ val32 = clk->occr;
+ udelay(2000);
+ clk->occr = 0xff000000;
+ udelay(2000);
+
+ iounmap(clk);
+
+ hose1 = pcibios_alloc_controller();
+ if(!hose1)
+ return;
+
+ ppc_md.pci_swizzle = common_swizzle;
+ ppc_md.pci_map_irq = mpc83xx_map_irq;
+
+ hose1->bus_offset = 0;
+ hose1->first_busno = 0;
+ hose1->last_busno = 0xff;
+
+ setup_indirect_pci(hose1, binfo->bi_immr_base + PCI1_CFG_ADDR_OFFSET,
+ binfo->bi_immr_base + PCI1_CFG_DATA_OFFSET);
+ hose1->set_cfg_type = 1;
+
+ mpc83xx_setup_pci1(hose1);
+
+ hose1->pci_mem_offset = MPC83xx_PCI1_MEM_OFFSET;
+ hose1->mem_space.start = MPC83xx_PCI1_LOWER_MEM;
+ hose1->mem_space.end = MPC83xx_PCI1_UPPER_MEM;
+
+ hose1->io_base_phys = MPC83xx_PCI1_IO_BASE;
+ hose1->io_space.start = MPC83xx_PCI1_LOWER_IO;
+ hose1->io_space.end = MPC83xx_PCI1_UPPER_IO;
+#ifdef CONFIG_MPC83xx_PCI2
+ isa_io_base = (unsigned long)ioremap(MPC83xx_PCI1_IO_BASE,
+ MPC83xx_PCI1_IO_SIZE + MPC83xx_PCI2_IO_SIZE);
+#else
+ isa_io_base = (unsigned long)ioremap(MPC83xx_PCI1_IO_BASE,
+ MPC83xx_PCI1_IO_SIZE);
+#endif /* CONFIG_MPC83xx_PCI2 */
+ hose1->io_base_virt = (void *)isa_io_base;
+ /* setup resources */
+ pci_init_resource(&hose1->io_resource,
+ MPC83xx_PCI1_LOWER_IO,
+ MPC83xx_PCI1_UPPER_IO,
+ IORESOURCE_IO, "PCI host bridge 1");
+ pci_init_resource(&hose1->mem_resources[0],
+ MPC83xx_PCI1_LOWER_MEM,
+ MPC83xx_PCI1_UPPER_MEM,
+ IORESOURCE_MEM, "PCI host bridge 1");
+
+ ppc_md.pci_exclude_device = mpc83xx_exclude_device;
+ hose1->last_busno = pciauto_bus_scan(hose1, hose1->first_busno);
+
+#ifdef CONFIG_MPC83xx_PCI2
+ hose2 = pcibios_alloc_controller();
+ if(!hose2)
+ return;
+
+ hose2->bus_offset = hose1->last_busno + 1;
+ hose2->first_busno = hose1->last_busno + 1;
+ hose2->last_busno = 0xff;
+ setup_indirect_pci(hose2, binfo->bi_immr_base + PCI2_CFG_ADDR_OFFSET,
+ binfo->bi_immr_base + PCI2_CFG_DATA_OFFSET);
+ hose2->set_cfg_type = 1;
+
+ mpc83xx_setup_pci2(hose2);
+
+ hose2->pci_mem_offset = MPC83xx_PCI2_MEM_OFFSET;
+ hose2->mem_space.start = MPC83xx_PCI2_LOWER_MEM;
+ hose2->mem_space.end = MPC83xx_PCI2_UPPER_MEM;
+
+ hose2->io_base_phys = MPC83xx_PCI2_IO_BASE;
+ hose2->io_space.start = MPC83xx_PCI2_LOWER_IO;
+ hose2->io_space.end = MPC83xx_PCI2_UPPER_IO;
+ hose2->io_base_virt = (void *)(isa_io_base + MPC83xx_PCI1_IO_SIZE);
+ /* setup resources */
+ pci_init_resource(&hose2->io_resource,
+ MPC83xx_PCI2_LOWER_IO,
+ MPC83xx_PCI2_UPPER_IO,
+ IORESOURCE_IO, "PCI host bridge 2");
+ pci_init_resource(&hose2->mem_resources[0],
+ MPC83xx_PCI2_LOWER_MEM,
+ MPC83xx_PCI2_UPPER_MEM,
+ IORESOURCE_MEM, "PCI host bridge 2");
+
+ hose2->last_busno = pciauto_bus_scan(hose2, hose2->first_busno);
+#endif /* CONFIG_MPC83xx_PCI2 */
+}
+#endif /*CONFIG_PCI*/
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.