1 files changed, 516 insertions, 0 deletions
diff --git a/drivers/ide/pci/sl82c105.c b/drivers/ide/pci/sl82c105.c
new file mode 100644
index 000000000000..1d970a0de21a
--- /dev/null
+++ b/drivers/ide/pci/sl82c105.c
@@ -0,0 +1,516 @@
+/*
+ * linux/drivers/ide/pci/sl82c105.c
+ *
+ * SL82C105/Winbond 553 IDE driver
+ *
+ * Maintainer unknown.
+ *
+ * Drive tuning added from Rebel.com's kernel sources
+ *  -- Russell King (15/11/98) linux@arm.linux.org.uk
+ * 
+ * Merge in Russell's HW workarounds, fix various problems
+ * with the timing registers setup.
+ *  -- Benjamin Herrenschmidt (01/11/03) benh@kernel.crashing.org
+ */
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/ioport.h>
+#include <linux/interrupt.h>
+#include <linux/blkdev.h>
+#include <linux/hdreg.h>
+#include <linux/pci.h>
+#include <linux/ide.h>
+
+#include <asm/io.h>
+#include <asm/dma.h>
+
+#undef DEBUG
+
+#ifdef DEBUG
+#define DBG(arg) printk arg
+#else
+#define DBG(fmt,...)
+#endif
+/*
+ * SL82C105 PCI config register 0x40 bits.
+ */
+#define CTRL_IDE_IRQB   (1 << 30)
+#define CTRL_IDE_IRQA   (1 << 28)
+#define CTRL_LEGIRQ     (1 << 11)
+#define CTRL_P1F16      (1 << 5)
+#define CTRL_P1EN       (1 << 4)
+#define CTRL_P0F16      (1 << 1)
+#define CTRL_P0EN       (1 << 0)
+
+/*
+ * Convert a PIO mode and cycle time to the required on/off
+ * times for the interface.  This has protection against run-away
+ * timings.
+ */
+static unsigned int get_timing_sl82c105(ide_pio_data_t *p)
+{
+	unsigned int cmd_on;
+	unsigned int cmd_off;
+
+	cmd_on = (ide_pio_timings[p->pio_mode].active_time + 29) / 30;
+	cmd_off = (p->cycle_time - 30 * cmd_on + 29) / 30;
+
+	if (cmd_on > 32)
+		cmd_on = 32;
+	if (cmd_on == 0)
+		cmd_on = 1;
+
+	if (cmd_off > 32)
+		cmd_off = 32;
+	if (cmd_off == 0)
+		cmd_off = 1;
+
+	return (cmd_on - 1) << 8 | (cmd_off - 1) | (p->use_iordy ? 0x40 : 0x00);
+}
+
+/*
+ * Configure the drive and chipset for PIO
+ */
+static void config_for_pio(ide_drive_t *drive, int pio, int report, int chipset_only)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	struct pci_dev *dev = hwif->pci_dev;
+	ide_pio_data_t p;
+	u16 drv_ctrl = 0x909;
+	unsigned int xfer_mode, reg;
+
+	DBG(("config_for_pio(drive:%s, pio:%d, report:%d, chipset_only:%d)\n",
+		drive->name, pio, report, chipset_only));
+		
+	reg = (hwif->channel ? 0x4c : 0x44) + (drive->select.b.unit ? 4 : 0);
+
+	pio = ide_get_best_pio_mode(drive, pio, 5, &p);
+
+	xfer_mode = XFER_PIO_0 + pio;
+
+	if (chipset_only || ide_config_drive_speed(drive, xfer_mode) == 0) {
+		drv_ctrl = get_timing_sl82c105(&p);
+		drive->pio_speed = xfer_mode;
+	} else
+		drive->pio_speed = XFER_PIO_0;
+
+	if (drive->using_dma == 0) {
+		/*
+		 * If we are actually using MW DMA, then we can not
+		 * reprogram the interface drive control register.
+		 */
+		pci_write_config_word(dev, reg, drv_ctrl);
+		pci_read_config_word(dev, reg, &drv_ctrl);
+
+		if (report) {
+			printk("%s: selected %s (%dns) (%04X)\n", drive->name,
+			       ide_xfer_verbose(xfer_mode), p.cycle_time, drv_ctrl);
+		}
+	}
+}
+
+/*
+ * Configure the drive and the chipset for DMA
+ */
+static int config_for_dma (ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	struct pci_dev *dev = hwif->pci_dev;
+	unsigned int reg;
+
+	DBG(("config_for_dma(drive:%s)\n", drive->name));
+
+	reg = (hwif->channel ? 0x4c : 0x44) + (drive->select.b.unit ? 4 : 0);
+
+	if (ide_config_drive_speed(drive, XFER_MW_DMA_2) != 0)
+		return 1;
+
+	pci_write_config_word(dev, reg, 0x0240);
+
+	return 0;
+}
+
+/*
+ * Check to see if the drive and
+ * chipset is capable of DMA mode
+ */
+
+static int sl82c105_check_drive (ide_drive_t *drive)
+{
+	ide_hwif_t *hwif	= HWIF(drive);
+
+	DBG(("sl82c105_check_drive(drive:%s)\n", drive->name));
+
+	do {
+		struct hd_driveid *id = drive->id;
+
+		if (!drive->autodma)
+			break;
+
+		if (!id || !(id->capability & 1))
+			break;
+
+		/* Consult the list of known "bad" drives */
+		if (__ide_dma_bad_drive(drive))
+			break;
+
+		if (id->field_valid & 2) {
+			if ((id->dma_mword & hwif->mwdma_mask) ||
+			    (id->dma_1word & hwif->swdma_mask))
+				return hwif->ide_dma_on(drive);
+		}
+
+		if (__ide_dma_good_drive(drive))
+			return hwif->ide_dma_on(drive);
+	} while (0);
+
+	return hwif->ide_dma_off_quietly(drive);
+}
+
+/*
+ * The SL82C105 holds off all IDE interrupts while in DMA mode until
+ * all DMA activity is completed.  Sometimes this causes problems (eg,
+ * when the drive wants to report an error condition).
+ *
+ * 0x7e is a "chip testing" register.  Bit 2 resets the DMA controller
+ * state machine.  We need to kick this to work around various bugs.
+ */
+static inline void sl82c105_reset_host(struct pci_dev *dev)
+{
+	u16 val;
+
+	pci_read_config_word(dev, 0x7e, &val);
+	pci_write_config_word(dev, 0x7e, val | (1 << 2));
+	pci_write_config_word(dev, 0x7e, val & ~(1 << 2));
+}
+
+/*
+ * If we get an IRQ timeout, it might be that the DMA state machine
+ * got confused.  Fix from Todd Inglett.  Details from Winbond.
+ *
+ * This function is called when the IDE timer expires, the drive
+ * indicates that it is READY, and we were waiting for DMA to complete.
+ */
+static int sl82c105_ide_dma_lost_irq(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	struct pci_dev *dev = hwif->pci_dev;
+	u32 val, mask = hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
+	unsigned long dma_base = hwif->dma_base;
+
+	printk("sl82c105: lost IRQ: resetting host\n");
+
+	/*
+	 * Check the raw interrupt from the drive.
+	 */
+	pci_read_config_dword(dev, 0x40, &val);
+	if (val & mask)
+		printk("sl82c105: drive was requesting IRQ, but host lost it\n");
+
+	/*
+	 * Was DMA enabled?  If so, disable it - we're resetting the
+	 * host.  The IDE layer will be handling the drive for us.
+	 */
+	val = hwif->INB(dma_base);
+	if (val & 1) {
+		outb(val & ~1, dma_base);
+		printk("sl82c105: DMA was enabled\n");
+	}
+
+	sl82c105_reset_host(dev);
+
+	/* ide_dmaproc would return 1, so we do as well */
+	return 1;
+}
+
+/*
+ * ATAPI devices can cause the SL82C105 DMA state machine to go gaga.
+ * Winbond recommend that the DMA state machine is reset prior to
+ * setting the bus master DMA enable bit.
+ *
+ * The generic IDE core will have disabled the BMEN bit before this
+ * function is called.
+ */
+static void sl82c105_ide_dma_start(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	struct pci_dev *dev = hwif->pci_dev;
+
+	sl82c105_reset_host(dev);
+	ide_dma_start(drive);
+}
+
+static int sl82c105_ide_dma_timeout(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	struct pci_dev *dev = hwif->pci_dev;
+
+	DBG(("sl82c105_ide_dma_timeout(drive:%s)\n", drive->name));
+
+	sl82c105_reset_host(dev);
+	return __ide_dma_timeout(drive);
+}
+
+static int sl82c105_ide_dma_on (ide_drive_t *drive)
+{
+	DBG(("sl82c105_ide_dma_on(drive:%s)\n", drive->name));
+
+	if (config_for_dma(drive)) {
+		config_for_pio(drive, 4, 0, 0);
+		return HWIF(drive)->ide_dma_off_quietly(drive);
+	}
+	printk(KERN_INFO "%s: DMA enabled\n", drive->name);
+	return __ide_dma_on(drive);
+}
+
+static int sl82c105_ide_dma_off_quietly (ide_drive_t *drive)
+{
+	u8 speed = XFER_PIO_0;
+	int rc;
+	
+	DBG(("sl82c105_ide_dma_off_quietly(drive:%s)\n", drive->name));
+
+	rc = __ide_dma_off_quietly(drive);
+	if (drive->pio_speed)
+		speed = drive->pio_speed - XFER_PIO_0;
+	config_for_pio(drive, speed, 0, 1);
+	drive->current_speed = drive->pio_speed;
+
+	return rc;
+}
+
+/*
+ * Ok, that is nasty, but we must make sure the DMA timings
+ * won't be used for a PIO access. The solution here is
+ * to make sure the 16 bits mode is diabled on the channel
+ * when DMA is enabled, thus causing the chip to use PIO0
+ * timings for those operations.
+ */
+static void sl82c105_selectproc(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	struct pci_dev *dev = hwif->pci_dev;
+	u32 val, old, mask;
+
+	//DBG(("sl82c105_selectproc(drive:%s)\n", drive->name));
+
+	mask = hwif->channel ? CTRL_P1F16 : CTRL_P0F16;
+	old = val = *((u32 *)&hwif->hwif_data);
+	if (drive->using_dma)
+		val &= ~mask;
+	else
+		val |= mask;
+	if (old != val) {
+		pci_write_config_dword(dev, 0x40, val);	
+		*((u32 *)&hwif->hwif_data) = val;
+	}
+}
+
+/*
+ * ATA reset will clear the 16 bits mode in the control
+ * register, we need to update our cache
+ */
+static void sl82c105_resetproc(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	struct pci_dev *dev = hwif->pci_dev;
+	u32 val;
+
+	DBG(("sl82c105_resetproc(drive:%s)\n", drive->name));
+
+	pci_read_config_dword(dev, 0x40, &val);
+	*((u32 *)&hwif->hwif_data) = val;
+}
+	
+/*
+ * We only deal with PIO mode here - DMA mode 'using_dma' is not
+ * initialised at the point that this function is called.
+ */
+static void tune_sl82c105(ide_drive_t *drive, u8 pio)
+{
+	DBG(("tune_sl82c105(drive:%s)\n", drive->name));
+
+	config_for_pio(drive, pio, 1, 0);
+
+	/*
+	 * We support 32-bit I/O on this interface, and it
+	 * doesn't have problems with interrupts.
+	 */
+	drive->io_32bit = 1;
+	drive->unmask = 1;
+}
+
+/*
+ * Return the revision of the Winbond bridge
+ * which this function is part of.
+ */
+static unsigned int sl82c105_bridge_revision(struct pci_dev *dev)
+{
+	struct pci_dev *bridge;
+	u8 rev;
+
+	/*
+	 * The bridge should be part of the same device, but function 0.
+	 */
+	bridge = pci_find_slot(dev->bus->number,
+			       PCI_DEVFN(PCI_SLOT(dev->devfn), 0));
+	if (!bridge)
+		return -1;
+
+	/*
+	 * Make sure it is a Winbond 553 and is an ISA bridge.
+	 */
+	if (bridge->vendor != PCI_VENDOR_ID_WINBOND ||
+	    bridge->device != PCI_DEVICE_ID_WINBOND_83C553 ||
+	    bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA)
+		return -1;
+
+	/*
+	 * We need to find function 0's revision, not function 1
+	 */
+	pci_read_config_byte(bridge, PCI_REVISION_ID, &rev);
+
+	return rev;
+}
+
+/*
+ * Enable the PCI device
+ * 
+ * --BenH: It's arch fixup code that should enable channels that
+ * have not been enabled by firmware. I decided we can still enable
+ * channel 0 here at least, but channel 1 has to be enabled by
+ * firmware or arch code. We still set both to 16 bits mode.
+ */
+static unsigned int __init init_chipset_sl82c105(struct pci_dev *dev, const char *msg)
+{
+	u32 val;
+
+	DBG(("init_chipset_sl82c105()\n"));
+
+	pci_read_config_dword(dev, 0x40, &val);
+	val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
+	pci_write_config_dword(dev, 0x40, val);
+
+	return dev->irq;
+}
+
+static void __init init_dma_sl82c105(ide_hwif_t *hwif, unsigned long dma_base)
+{
+	unsigned int rev;
+	u8 dma_state;
+
+	DBG(("init_dma_sl82c105(hwif: ide%d, dma_base: 0x%08x)\n", hwif->index, dma_base));
+
+	hwif->autodma = 0;
+
+	if (!dma_base)
+		return;
+
+	dma_state = hwif->INB(dma_base + 2);
+	rev = sl82c105_bridge_revision(hwif->pci_dev);
+	if (rev <= 5) {
+		printk("    %s: Winbond 553 bridge revision %d, BM-DMA disabled\n",
+		       hwif->name, rev);
+		dma_state &= ~0x60;
+	} else {
+		dma_state |= 0x60;
+		if (!noautodma)
+			hwif->autodma = 1;
+	}
+	hwif->OUTB(dma_state, dma_base + 2);
+
+	ide_setup_dma(hwif, dma_base, 8);
+}
+
+/*
+ * Initialise the chip
+ */
+
+static void __init init_hwif_sl82c105(ide_hwif_t *hwif)
+{
+	struct pci_dev *dev = hwif->pci_dev;
+	u32 val;
+	
+	DBG(("init_hwif_sl82c105(hwif: ide%d)\n", hwif->index));
+
+	hwif->tuneproc = tune_sl82c105;
+	hwif->selectproc = sl82c105_selectproc;
+	hwif->resetproc = sl82c105_resetproc;
+	
+	/* Default to PIO 0 for fallback unless tuned otherwise,
+	 * we always autotune PIO, this is done before DMA is
+	 * checked, so there is no risk of accidentally disabling
+	 * DMA
+	  */
+	hwif->drives[0].pio_speed = XFER_PIO_0;
+	hwif->drives[0].autotune = 1;
+	hwif->drives[1].pio_speed = XFER_PIO_1;
+	hwif->drives[1].autotune = 1;
+
+	pci_read_config_dword(dev, 0x40, &val);
+	*((u32 *)&hwif->hwif_data) = val;
+	
+	if (!hwif->dma_base)
+		return;
+
+	hwif->atapi_dma = 1;
+	hwif->mwdma_mask = 0x07;
+	hwif->swdma_mask = 0x07;
+
+#ifdef CONFIG_BLK_DEV_IDEDMA
+	hwif->ide_dma_check = &sl82c105_check_drive;
+	hwif->ide_dma_on = &sl82c105_ide_dma_on;
+	hwif->ide_dma_off_quietly = &sl82c105_ide_dma_off_quietly;
+	hwif->ide_dma_lostirq = &sl82c105_ide_dma_lost_irq;
+	hwif->dma_start = &sl82c105_ide_dma_start;
+	hwif->ide_dma_timeout = &sl82c105_ide_dma_timeout;
+
+	if (!noautodma)
+		hwif->autodma = 1;
+	hwif->drives[0].autodma = hwif->autodma;
+	hwif->drives[1].autodma = hwif->autodma;
+#endif /* CONFIG_BLK_DEV_IDEDMA */
+}
+
+static ide_pci_device_t sl82c105_chipset __devinitdata = {
+	.name		= "W82C105",
+	.init_chipset	= init_chipset_sl82c105,
+	.init_hwif	= init_hwif_sl82c105,
+	.init_dma	= init_dma_sl82c105,
+	.channels	= 2,
+	.autodma	= NOAUTODMA,
+	.enablebits	= {{0x40,0x01,0x01}, {0x40,0x10,0x10}},
+	.bootable	= ON_BOARD,
+};
+
+static int __devinit sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	return ide_setup_pci_device(dev, &sl82c105_chipset);
+}
+
+static struct pci_device_id sl82c105_pci_tbl[] = {
+	{ PCI_VENDOR_ID_WINBOND, PCI_DEVICE_ID_WINBOND_82C105, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+	{ 0, },
+};
+MODULE_DEVICE_TABLE(pci, sl82c105_pci_tbl);
+
+static struct pci_driver driver = {
+	.name		= "W82C105_IDE",
+	.id_table	= sl82c105_pci_tbl,
+	.probe		= sl82c105_init_one,
+};
+
+static int sl82c105_ide_init(void)
+{
+	return ide_pci_register_driver(&driver);
+}
+
+module_init(sl82c105_ide_init);
+
+MODULE_DESCRIPTION("PCI driver module for W82C105 IDE");
+MODULE_LICENSE("GPL");