diff options
Diffstat (limited to 'drivers/mmc')
| -rw-r--r-- | drivers/mmc/host/sdhci-msm.c | 125 |
1 files changed, 123 insertions, 2 deletions
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c index 5c73f7dfc83b..32879b845b75 100644 --- a/drivers/mmc/host/sdhci-msm.c +++ b/drivers/mmc/host/sdhci-msm.c @@ -52,6 +52,7 @@ #define INT_MASK 0xf #define MAX_PHASES 16 #define CORE_DLL_LOCK BIT(7) +#define CORE_DDR_DLL_LOCK BIT(11) #define CORE_DLL_EN BIT(16) #define CORE_CDR_EN BIT(17) #define CORE_CK_OUT_EN BIT(18) @@ -63,6 +64,7 @@ #define CORE_DLL_STATUS 0x108 #define CORE_DLL_CONFIG_2 0x1b4 +#define CORE_DDR_CAL_EN BIT(0) #define CORE_FLL_CYCLE_CNT BIT(18) #define CORE_DLL_CLOCK_DISABLE BIT(21) @@ -101,6 +103,11 @@ #define CORE_DDR_200_CFG 0x184 #define CORE_CDC_T4_DLY_SEL BIT(0) #define CORE_START_CDC_TRAFFIC BIT(6) +#define CORE_VENDOR_SPEC3 0x1b0 +#define CORE_PWRSAVE_DLL BIT(3) + +#define CORE_DDR_CONFIG 0x1b8 +#define DDR_CONFIG_POR_VAL 0x80040853 #define CORE_VENDOR_SPEC_CAPABILITIES0 0x11c @@ -128,6 +135,7 @@ struct sdhci_msm_host { bool tuning_done; bool calibration_done; u8 saved_tuning_phase; + bool use_cdclp533; }; /* Platform specific tuning */ @@ -569,6 +577,87 @@ out: return ret; } +static int sdhci_msm_cm_dll_sdc4_calibration(struct sdhci_host *host) +{ + u32 dll_status, config; + int ret; + + pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__); + + /* + * Currently the CORE_DDR_CONFIG register defaults to desired + * configuration on reset. Currently reprogramming the power on + * reset (POR) value in case it might have been modified by + * bootloaders. In the future, if this changes, then the desired + * values will need to be programmed appropriately. + */ + writel_relaxed(DDR_CONFIG_POR_VAL, host->ioaddr + CORE_DDR_CONFIG); + + config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG_2); + config |= CORE_DDR_CAL_EN; + writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG_2); + + ret = readl_relaxed_poll_timeout(host->ioaddr + CORE_DLL_STATUS, + dll_status, + (dll_status & CORE_DDR_DLL_LOCK), + 10, 1000); + + if (ret == -ETIMEDOUT) { + pr_err("%s: %s: CM_DLL_SDC4 calibration was not completed\n", + mmc_hostname(host->mmc), __func__); + goto out; + } + + config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC3); + config |= CORE_PWRSAVE_DLL; + writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC3); + + /* + * Drain writebuffer to ensure above DLL calibration + * and PWRSAVE DLL is enabled. + */ + wmb(); +out: + pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc), + __func__, ret); + return ret; +} + +static int sdhci_msm_hs400_dll_calibration(struct sdhci_host *host) +{ + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); + int ret; + u32 config; + + pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__); + + /* + * Retuning in HS400 (DDR mode) will fail, just reset the + * tuning block and restore the saved tuning phase. + */ + ret = msm_init_cm_dll(host); + if (ret) + goto out; + + /* Set the selected phase in delay line hw block */ + ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase); + if (ret) + goto out; + + config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG); + config |= CORE_CMD_DAT_TRACK_SEL; + writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG); + if (msm_host->use_cdclp533) + ret = sdhci_msm_cdclp533_calibration(host); + else + ret = sdhci_msm_cm_dll_sdc4_calibration(host); +out: + pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc), + __func__, ret); + return ret; +} + static int sdhci_msm_execute_tuning(struct sdhci_host *host, u32 opcode) { int tuning_seq_cnt = 3; @@ -715,7 +804,7 @@ static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host, if (host->clock > CORE_FREQ_100MHZ && msm_host->tuning_done && !msm_host->calibration_done && mmc->ios.timing == MMC_TIMING_MMC_HS400) - if (!sdhci_msm_cdclp533_calibration(host)) + if (!sdhci_msm_hs400_dll_calibration(host)) msm_host->calibration_done = true; spin_lock_irq(&host->lock); } @@ -805,7 +894,7 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock) struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host); struct mmc_ios curr_ios = host->mmc->ios; - u32 config; + u32 config, dll_lock; int rc; if (!clock) { @@ -862,7 +951,32 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock) config |= CORE_HC_SELECT_IN_EN; writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC); } + if (!msm_host->clk_rate && !msm_host->use_cdclp533) { + /* + * Poll on DLL_LOCK or DDR_DLL_LOCK bits in + * CORE_DLL_STATUS to be set. This should get set + * within 15 us at 200 MHz. + */ + rc = readl_relaxed_poll_timeout(host->ioaddr + + CORE_DLL_STATUS, + dll_lock, + (dll_lock & + (CORE_DLL_LOCK | + CORE_DDR_DLL_LOCK)), 10, + 1000); + if (rc == -ETIMEDOUT) + pr_err("%s: Unable to get DLL_LOCK/DDR_DLL_LOCK, dll_status: 0x%08x\n", + mmc_hostname(host->mmc), dll_lock); + } } else { + if (!msm_host->use_cdclp533) { + config = readl_relaxed(host->ioaddr + + CORE_VENDOR_SPEC3); + config &= ~CORE_PWRSAVE_DLL; + writel_relaxed(config, host->ioaddr + + CORE_VENDOR_SPEC3); + } + config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC); config &= ~CORE_HC_MCLK_SEL_MASK; config |= CORE_HC_MCLK_SEL_DFLT; @@ -1055,6 +1169,13 @@ static int sdhci_msm_probe(struct platform_device *pdev) msm_host->use_14lpp_dll_reset = true; /* + * SDCC 5 controller with major version 1, minor version 0x34 and later + * with HS 400 mode support will use CM DLL instead of CDC LP 533 DLL. + */ + if (core_major == 1 && core_minor < 0x34) + msm_host->use_cdclp533 = true; + + /* * Support for some capabilities is not advertised by newer * controller versions and must be explicitly enabled. */ |