diff options
Diffstat (limited to 'drivers/net/dsa/realtek/rtl8365mb.c')
| -rw-r--r-- | drivers/net/dsa/realtek/rtl8365mb.c | 2113 |
1 files changed, 2113 insertions, 0 deletions
diff --git a/drivers/net/dsa/realtek/rtl8365mb.c b/drivers/net/dsa/realtek/rtl8365mb.c new file mode 100644 index 000000000000..3d70e8a77ecf --- /dev/null +++ b/drivers/net/dsa/realtek/rtl8365mb.c @@ -0,0 +1,2113 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Realtek SMI subdriver for the Realtek RTL8365MB-VC ethernet switch. + * + * Copyright (C) 2021 Alvin Šipraga <alsi@bang-olufsen.dk> + * Copyright (C) 2021 Michael Rasmussen <mir@bang-olufsen.dk> + * + * The RTL8365MB-VC is a 4+1 port 10/100/1000M switch controller. It includes 4 + * integrated PHYs for the user facing ports, and an extension interface which + * can be connected to the CPU - or another PHY - via either MII, RMII, or + * RGMII. The switch is configured via the Realtek Simple Management Interface + * (SMI), which uses the MDIO/MDC lines. + * + * Below is a simplified block diagram of the chip and its relevant interfaces. + * + * .-----------------------------------. + * | | + * UTP <---------------> Giga PHY <-> PCS <-> P0 GMAC | + * UTP <---------------> Giga PHY <-> PCS <-> P1 GMAC | + * UTP <---------------> Giga PHY <-> PCS <-> P2 GMAC | + * UTP <---------------> Giga PHY <-> PCS <-> P3 GMAC | + * | | + * CPU/PHY <-MII/RMII/RGMII---> Extension <---> Extension | + * | interface 1 GMAC 1 | + * | | + * SMI driver/ <-MDC/SCL---> Management ~~~~~~~~~~~~~~ | + * EEPROM <-MDIO/SDA--> interface ~REALTEK ~~~~~ | + * | ~RTL8365MB ~~~ | + * | ~GXXXC TAIWAN~ | + * GPIO <--------------> Reset ~~~~~~~~~~~~~~ | + * | | + * Interrupt <----------> Link UP/DOWN events | + * controller | | + * '-----------------------------------' + * + * The driver uses DSA to integrate the 4 user and 1 extension ports into the + * kernel. Netdevices are created for the user ports, as are PHY devices for + * their integrated PHYs. The device tree firmware should also specify the link + * partner of the extension port - either via a fixed-link or other phy-handle. + * See the device tree bindings for more detailed information. Note that the + * driver has only been tested with a fixed-link, but in principle it should not + * matter. + * + * NOTE: Currently, only the RGMII interface is implemented in this driver. + * + * The interrupt line is asserted on link UP/DOWN events. The driver creates a + * custom irqchip to handle this interrupt and demultiplex the events by reading + * the status registers via SMI. Interrupts are then propagated to the relevant + * PHY device. + * + * The EEPROM contains initial register values which the chip will read over I2C + * upon hardware reset. It is also possible to omit the EEPROM. In both cases, + * the driver will manually reprogram some registers using jam tables to reach + * an initial state defined by the vendor driver. + * + * This Linux driver is written based on an OS-agnostic vendor driver from + * Realtek. The reference GPL-licensed sources can be found in the OpenWrt + * source tree under the name rtl8367c. The vendor driver claims to support a + * number of similar switch controllers from Realtek, but the only hardware we + * have is the RTL8365MB-VC. Moreover, there does not seem to be any chip under + * the name RTL8367C. Although one wishes that the 'C' stood for some kind of + * common hardware revision, there exist examples of chips with the suffix -VC + * which are explicitly not supported by the rtl8367c driver and which instead + * require the rtl8367d vendor driver. With all this uncertainty, the driver has + * been modestly named rtl8365mb. Future implementors may wish to rename things + * accordingly. + * + * In the same family of chips, some carry up to 8 user ports and up to 2 + * extension ports. Where possible this driver tries to make things generic, but + * more work must be done to support these configurations. According to + * documentation from Realtek, the family should include the following chips: + * + * - RTL8363NB + * - RTL8363NB-VB + * - RTL8363SC + * - RTL8363SC-VB + * - RTL8364NB + * - RTL8364NB-VB + * - RTL8365MB-VC + * - RTL8366SC + * - RTL8367RB-VB + * - RTL8367SB + * - RTL8367S + * - RTL8370MB + * - RTL8310SR + * + * Some of the register logic for these additional chips has been skipped over + * while implementing this driver. It is therefore not possible to assume that + * things will work out-of-the-box for other chips, and a careful review of the + * vendor driver may be needed to expand support. The RTL8365MB-VC seems to be + * one of the simpler chips. + */ + +#include <linux/bitfield.h> +#include <linux/bitops.h> +#include <linux/interrupt.h> +#include <linux/irqdomain.h> +#include <linux/mutex.h> +#include <linux/of_irq.h> +#include <linux/regmap.h> +#include <linux/if_bridge.h> + +#include "realtek.h" + +/* Chip-specific data and limits */ +#define RTL8365MB_CHIP_ID_8365MB_VC 0x6367 +#define RTL8365MB_CHIP_VER_8365MB_VC 0x0040 + +#define RTL8365MB_CHIP_ID_8367S 0x6367 +#define RTL8365MB_CHIP_VER_8367S 0x00A0 + +#define RTL8365MB_CHIP_ID_8367RB 0x6367 +#define RTL8365MB_CHIP_VER_8367RB 0x0020 + +/* Family-specific data and limits */ +#define RTL8365MB_PHYADDRMAX 7 +#define RTL8365MB_NUM_PHYREGS 32 +#define RTL8365MB_PHYREGMAX (RTL8365MB_NUM_PHYREGS - 1) +/* RTL8370MB and RTL8310SR, possibly suportable by this driver, have 10 ports */ +#define RTL8365MB_MAX_NUM_PORTS 10 +#define RTL8365MB_LEARN_LIMIT_MAX 2112 + +/* valid for all 6-port or less variants */ +static const int rtl8365mb_extint_port_map[] = { -1, -1, -1, -1, -1, -1, 1, 2, -1, -1}; + +/* Chip identification registers */ +#define RTL8365MB_CHIP_ID_REG 0x1300 + +#define RTL8365MB_CHIP_VER_REG 0x1301 + +#define RTL8365MB_MAGIC_REG 0x13C2 +#define RTL8365MB_MAGIC_VALUE 0x0249 + +/* Chip reset register */ +#define RTL8365MB_CHIP_RESET_REG 0x1322 +#define RTL8365MB_CHIP_RESET_SW_MASK 0x0002 +#define RTL8365MB_CHIP_RESET_HW_MASK 0x0001 + +/* Interrupt polarity register */ +#define RTL8365MB_INTR_POLARITY_REG 0x1100 +#define RTL8365MB_INTR_POLARITY_MASK 0x0001 +#define RTL8365MB_INTR_POLARITY_HIGH 0 +#define RTL8365MB_INTR_POLARITY_LOW 1 + +/* Interrupt control/status register - enable/check specific interrupt types */ +#define RTL8365MB_INTR_CTRL_REG 0x1101 +#define RTL8365MB_INTR_STATUS_REG 0x1102 +#define RTL8365MB_INTR_SLIENT_START_2_MASK 0x1000 +#define RTL8365MB_INTR_SLIENT_START_MASK 0x0800 +#define RTL8365MB_INTR_ACL_ACTION_MASK 0x0200 +#define RTL8365MB_INTR_CABLE_DIAG_FIN_MASK 0x0100 +#define RTL8365MB_INTR_INTERRUPT_8051_MASK 0x0080 +#define RTL8365MB_INTR_LOOP_DETECTION_MASK 0x0040 +#define RTL8365MB_INTR_GREEN_TIMER_MASK 0x0020 +#define RTL8365MB_INTR_SPECIAL_CONGEST_MASK 0x0010 +#define RTL8365MB_INTR_SPEED_CHANGE_MASK 0x0008 +#define RTL8365MB_INTR_LEARN_OVER_MASK 0x0004 +#define RTL8365MB_INTR_METER_EXCEEDED_MASK 0x0002 +#define RTL8365MB_INTR_LINK_CHANGE_MASK 0x0001 +#define RTL8365MB_INTR_ALL_MASK \ + (RTL8365MB_INTR_SLIENT_START_2_MASK | \ + RTL8365MB_INTR_SLIENT_START_MASK | \ + RTL8365MB_INTR_ACL_ACTION_MASK | \ + RTL8365MB_INTR_CABLE_DIAG_FIN_MASK | \ + RTL8365MB_INTR_INTERRUPT_8051_MASK | \ + RTL8365MB_INTR_LOOP_DETECTION_MASK | \ + RTL8365MB_INTR_GREEN_TIMER_MASK | \ + RTL8365MB_INTR_SPECIAL_CONGEST_MASK | \ + RTL8365MB_INTR_SPEED_CHANGE_MASK | \ + RTL8365MB_INTR_LEARN_OVER_MASK | \ + RTL8365MB_INTR_METER_EXCEEDED_MASK | \ + RTL8365MB_INTR_LINK_CHANGE_MASK) + +/* Per-port interrupt type status registers */ +#define RTL8365MB_PORT_LINKDOWN_IND_REG 0x1106 +#define RTL8365MB_PORT_LINKDOWN_IND_MASK 0x07FF + +#define RTL8365MB_PORT_LINKUP_IND_REG 0x1107 +#define RTL8365MB_PORT_LINKUP_IND_MASK 0x07FF + +/* PHY indirect access registers */ +#define RTL8365MB_INDIRECT_ACCESS_CTRL_REG 0x1F00 +#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK 0x0002 +#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ 0 +#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE 1 +#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK 0x0001 +#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE 1 +#define RTL8365MB_INDIRECT_ACCESS_STATUS_REG 0x1F01 +#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG 0x1F02 +#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK GENMASK(4, 0) +#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK GENMASK(7, 5) +#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK GENMASK(11, 8) +#define RTL8365MB_PHY_BASE 0x2000 +#define RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG 0x1F03 +#define RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG 0x1F04 + +/* PHY OCP address prefix register */ +#define RTL8365MB_GPHY_OCP_MSB_0_REG 0x1D15 +#define RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK 0x0FC0 +#define RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK 0xFC00 + +/* The PHY OCP addresses of PHY registers 0~31 start here */ +#define RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE 0xA400 + +/* EXT interface port mode values - used in DIGITAL_INTERFACE_SELECT */ +#define RTL8365MB_EXT_PORT_MODE_DISABLE 0 +#define RTL8365MB_EXT_PORT_MODE_RGMII 1 +#define RTL8365MB_EXT_PORT_MODE_MII_MAC 2 +#define RTL8365MB_EXT_PORT_MODE_MII_PHY 3 +#define RTL8365MB_EXT_PORT_MODE_TMII_MAC 4 +#define RTL8365MB_EXT_PORT_MODE_TMII_PHY 5 +#define RTL8365MB_EXT_PORT_MODE_GMII 6 +#define RTL8365MB_EXT_PORT_MODE_RMII_MAC 7 +#define RTL8365MB_EXT_PORT_MODE_RMII_PHY 8 +#define RTL8365MB_EXT_PORT_MODE_SGMII 9 +#define RTL8365MB_EXT_PORT_MODE_HSGMII 10 +#define RTL8365MB_EXT_PORT_MODE_1000X_100FX 11 +#define RTL8365MB_EXT_PORT_MODE_1000X 12 +#define RTL8365MB_EXT_PORT_MODE_100FX 13 + +/* Realtek docs and driver uses logic number as EXT_PORT0=16, EXT_PORT1=17, + * EXT_PORT2=18, to interact with switch ports. That logic number is internally + * converted to either a physical port number (0..9) or an external interface id (0..2), + * depending on which function was called. The external interface id is calculated as + * (ext_id=logic_port-15), while the logical to physical map depends on the chip id/version. + * + * EXT_PORT0 mentioned in datasheets and rtl8367c driver is used in this driver + * as extid==1, EXT_PORT2, mentioned in Realtek rtl8367c driver for 10-port switches, + * would have an ext_id of 3 (out of range for most extint macros) and ext_id 0 does + * not seem to be used as well for this family. + */ + +/* EXT interface mode configuration registers 0~1 */ +#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 0x1305 /* EXT1 */ +#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 0x13C3 /* EXT2 */ +#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(_extint) \ + ((_extint) == 1 ? RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 : \ + (_extint) == 2 ? RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 : \ + 0x0) +#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(_extint) \ + (0xF << (((_extint) % 2))) +#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(_extint) \ + (((_extint) % 2) * 4) + +/* EXT interface RGMII TX/RX delay configuration registers 0~2 */ +#define RTL8365MB_EXT_RGMXF_REG0 0x1306 /* EXT0 */ +#define RTL8365MB_EXT_RGMXF_REG1 0x1307 /* EXT1 */ +#define RTL8365MB_EXT_RGMXF_REG2 0x13C5 /* EXT2 */ +#define RTL8365MB_EXT_RGMXF_REG(_extint) \ + ((_extint) == 0 ? RTL8365MB_EXT_RGMXF_REG0 : \ + (_extint) == 1 ? RTL8365MB_EXT_RGMXF_REG1 : \ + (_extint) == 2 ? RTL8365MB_EXT_RGMXF_REG2 : \ + 0x0) +#define RTL8365MB_EXT_RGMXF_RXDELAY_MASK 0x0007 +#define RTL8365MB_EXT_RGMXF_TXDELAY_MASK 0x0008 + +/* External interface port speed values - used in DIGITAL_INTERFACE_FORCE */ +#define RTL8365MB_PORT_SPEED_10M 0 +#define RTL8365MB_PORT_SPEED_100M 1 +#define RTL8365MB_PORT_SPEED_1000M 2 + +/* EXT interface force configuration registers 0~2 */ +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 0x1310 /* EXT0 */ +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 0x1311 /* EXT1 */ +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 0x13C4 /* EXT2 */ +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(_extint) \ + ((_extint) == 0 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 : \ + (_extint) == 1 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 : \ + (_extint) == 2 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 : \ + 0x0) +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK 0x1000 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_NWAY_MASK 0x0080 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK 0x0040 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK 0x0020 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK 0x0010 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK 0x0004 +#define RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK 0x0003 + +/* CPU port mask register - controls which ports are treated as CPU ports */ +#define RTL8365MB_CPU_PORT_MASK_REG 0x1219 +#define RTL8365MB_CPU_PORT_MASK_MASK 0x07FF + +/* CPU control register */ +#define RTL8365MB_CPU_CTRL_REG 0x121A +#define RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK 0x0400 +#define RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK 0x0200 +#define RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK 0x0080 +#define RTL8365MB_CPU_CTRL_TAG_POSITION_MASK 0x0040 +#define RTL8365MB_CPU_CTRL_TRAP_PORT_MASK 0x0038 +#define RTL8365MB_CPU_CTRL_INSERTMODE_MASK 0x0006 +#define RTL8365MB_CPU_CTRL_EN_MASK 0x0001 + +/* Maximum packet length register */ +#define RTL8365MB_CFG0_MAX_LEN_REG 0x088C +#define RTL8365MB_CFG0_MAX_LEN_MASK 0x3FFF + +/* Port learning limit registers */ +#define RTL8365MB_LUT_PORT_LEARN_LIMIT_BASE 0x0A20 +#define RTL8365MB_LUT_PORT_LEARN_LIMIT_REG(_physport) \ + (RTL8365MB_LUT_PORT_LEARN_LIMIT_BASE + (_physport)) + +/* Port isolation (forwarding mask) registers */ +#define RTL8365MB_PORT_ISOLATION_REG_BASE 0x08A2 +#define RTL8365MB_PORT_ISOLATION_REG(_physport) \ + (RTL8365MB_PORT_ISOLATION_REG_BASE + (_physport)) +#define RTL8365MB_PORT_ISOLATION_MASK 0x07FF + +/* MSTP port state registers - indexed by tree instance */ +#define RTL8365MB_MSTI_CTRL_BASE 0x0A00 +#define RTL8365MB_MSTI_CTRL_REG(_msti, _physport) \ + (RTL8365MB_MSTI_CTRL_BASE + ((_msti) << 1) + ((_physport) >> 3)) +#define RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET(_physport) ((_physport) << 1) +#define RTL8365MB_MSTI_CTRL_PORT_STATE_MASK(_physport) \ + (0x3 << RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET((_physport))) + +/* MIB counter value registers */ +#define RTL8365MB_MIB_COUNTER_BASE 0x1000 +#define RTL8365MB_MIB_COUNTER_REG(_x) (RTL8365MB_MIB_COUNTER_BASE + (_x)) + +/* MIB counter address register */ +#define RTL8365MB_MIB_ADDRESS_REG 0x1004 +#define RTL8365MB_MIB_ADDRESS_PORT_OFFSET 0x007C +#define RTL8365MB_MIB_ADDRESS(_p, _x) \ + (((RTL8365MB_MIB_ADDRESS_PORT_OFFSET) * (_p) + (_x)) >> 2) + +#define RTL8365MB_MIB_CTRL0_REG 0x1005 +#define RTL8365MB_MIB_CTRL0_RESET_MASK 0x0002 +#define RTL8365MB_MIB_CTRL0_BUSY_MASK 0x0001 + +/* The DSA callback .get_stats64 runs in atomic context, so we are not allowed + * to block. On the other hand, accessing MIB counters absolutely requires us to + * block. The solution is thus to schedule work which polls the MIB counters + * asynchronously and updates some private data, which the callback can then + * fetch atomically. Three seconds should be a good enough polling interval. + */ +#define RTL8365MB_STATS_INTERVAL_JIFFIES (3 * HZ) + +enum rtl8365mb_mib_counter_index { + RTL8365MB_MIB_ifInOctets, + RTL8365MB_MIB_dot3StatsFCSErrors, + RTL8365MB_MIB_dot3StatsSymbolErrors, + RTL8365MB_MIB_dot3InPauseFrames, + RTL8365MB_MIB_dot3ControlInUnknownOpcodes, + RTL8365MB_MIB_etherStatsFragments, + RTL8365MB_MIB_etherStatsJabbers, + RTL8365MB_MIB_ifInUcastPkts, + RTL8365MB_MIB_etherStatsDropEvents, + RTL8365MB_MIB_ifInMulticastPkts, + RTL8365MB_MIB_ifInBroadcastPkts, + RTL8365MB_MIB_inMldChecksumError, + RTL8365MB_MIB_inIgmpChecksumError, + RTL8365MB_MIB_inMldSpecificQuery, + RTL8365MB_MIB_inMldGeneralQuery, + RTL8365MB_MIB_inIgmpSpecificQuery, + RTL8365MB_MIB_inIgmpGeneralQuery, + RTL8365MB_MIB_inMldLeaves, + RTL8365MB_MIB_inIgmpLeaves, + RTL8365MB_MIB_etherStatsOctets, + RTL8365MB_MIB_etherStatsUnderSizePkts, + RTL8365MB_MIB_etherOversizeStats, + RTL8365MB_MIB_etherStatsPkts64Octets, + RTL8365MB_MIB_etherStatsPkts65to127Octets, + RTL8365MB_MIB_etherStatsPkts128to255Octets, + RTL8365MB_MIB_etherStatsPkts256to511Octets, + RTL8365MB_MIB_etherStatsPkts512to1023Octets, + RTL8365MB_MIB_etherStatsPkts1024to1518Octets, + RTL8365MB_MIB_ifOutOctets, + RTL8365MB_MIB_dot3StatsSingleCollisionFrames, + RTL8365MB_MIB_dot3StatsMultipleCollisionFrames, + RTL8365MB_MIB_dot3StatsDeferredTransmissions, + RTL8365MB_MIB_dot3StatsLateCollisions, + RTL8365MB_MIB_etherStatsCollisions, + RTL8365MB_MIB_dot3StatsExcessiveCollisions, + RTL8365MB_MIB_dot3OutPauseFrames, + RTL8365MB_MIB_ifOutDiscards, + RTL8365MB_MIB_dot1dTpPortInDiscards, + RTL8365MB_MIB_ifOutUcastPkts, + RTL8365MB_MIB_ifOutMulticastPkts, + RTL8365MB_MIB_ifOutBroadcastPkts, + RTL8365MB_MIB_outOampduPkts, + RTL8365MB_MIB_inOampduPkts, + RTL8365MB_MIB_inIgmpJoinsSuccess, + RTL8365MB_MIB_inIgmpJoinsFail, + RTL8365MB_MIB_inMldJoinsSuccess, + RTL8365MB_MIB_inMldJoinsFail, + RTL8365MB_MIB_inReportSuppressionDrop, + RTL8365MB_MIB_inLeaveSuppressionDrop, + RTL8365MB_MIB_outIgmpReports, + RTL8365MB_MIB_outIgmpLeaves, + RTL8365MB_MIB_outIgmpGeneralQuery, + RTL8365MB_MIB_outIgmpSpecificQuery, + RTL8365MB_MIB_outMldReports, + RTL8365MB_MIB_outMldLeaves, + RTL8365MB_MIB_outMldGeneralQuery, + RTL8365MB_MIB_outMldSpecificQuery, + RTL8365MB_MIB_inKnownMulticastPkts, + RTL8365MB_MIB_END, +}; + +struct rtl8365mb_mib_counter { + u32 offset; + u32 length; + const char *name; +}; + +#define RTL8365MB_MAKE_MIB_COUNTER(_offset, _length, _name) \ + [RTL8365MB_MIB_ ## _name] = { _offset, _length, #_name } + +static struct rtl8365mb_mib_counter rtl8365mb_mib_counters[] = { + RTL8365MB_MAKE_MIB_COUNTER(0, 4, ifInOctets), + RTL8365MB_MAKE_MIB_COUNTER(4, 2, dot3StatsFCSErrors), + RTL8365MB_MAKE_MIB_COUNTER(6, 2, dot3StatsSymbolErrors), + RTL8365MB_MAKE_MIB_COUNTER(8, 2, dot3InPauseFrames), + RTL8365MB_MAKE_MIB_COUNTER(10, 2, dot3ControlInUnknownOpcodes), + RTL8365MB_MAKE_MIB_COUNTER(12, 2, etherStatsFragments), + RTL8365MB_MAKE_MIB_COUNTER(14, 2, etherStatsJabbers), + RTL8365MB_MAKE_MIB_COUNTER(16, 2, ifInUcastPkts), + RTL8365MB_MAKE_MIB_COUNTER(18, 2, etherStatsDropEvents), + RTL8365MB_MAKE_MIB_COUNTER(20, 2, ifInMulticastPkts), + RTL8365MB_MAKE_MIB_COUNTER(22, 2, ifInBroadcastPkts), + RTL8365MB_MAKE_MIB_COUNTER(24, 2, inMldChecksumError), + RTL8365MB_MAKE_MIB_COUNTER(26, 2, inIgmpChecksumError), + RTL8365MB_MAKE_MIB_COUNTER(28, 2, inMldSpecificQuery), + RTL8365MB_MAKE_MIB_COUNTER(30, 2, inMldGeneralQuery), + RTL8365MB_MAKE_MIB_COUNTER(32, 2, inIgmpSpecificQuery), + RTL8365MB_MAKE_MIB_COUNTER(34, 2, inIgmpGeneralQuery), + RTL8365MB_MAKE_MIB_COUNTER(36, 2, inMldLeaves), + RTL8365MB_MAKE_MIB_COUNTER(38, 2, inIgmpLeaves), + RTL8365MB_MAKE_MIB_COUNTER(40, 4, etherStatsOctets), + RTL8365MB_MAKE_MIB_COUNTER(44, 2, etherStatsUnderSizePkts), + RTL8365MB_MAKE_MIB_COUNTER(46, 2, etherOversizeStats), + RTL8365MB_MAKE_MIB_COUNTER(48, 2, etherStatsPkts64Octets), + RTL8365MB_MAKE_MIB_COUNTER(50, 2, etherStatsPkts65to127Octets), + RTL8365MB_MAKE_MIB_COUNTER(52, 2, etherStatsPkts128to255Octets), + RTL8365MB_MAKE_MIB_COUNTER(54, 2, etherStatsPkts256to511Octets), + RTL8365MB_MAKE_MIB_COUNTER(56, 2, etherStatsPkts512to1023Octets), + RTL8365MB_MAKE_MIB_COUNTER(58, 2, etherStatsPkts1024to1518Octets), + RTL8365MB_MAKE_MIB_COUNTER(60, 4, ifOutOctets), + RTL8365MB_MAKE_MIB_COUNTER(64, 2, dot3StatsSingleCollisionFrames), + RTL8365MB_MAKE_MIB_COUNTER(66, 2, dot3StatsMultipleCollisionFrames), + RTL8365MB_MAKE_MIB_COUNTER(68, 2, dot3StatsDeferredTransmissions), + RTL8365MB_MAKE_MIB_COUNTER(70, 2, dot3StatsLateCollisions), + RTL8365MB_MAKE_MIB_COUNTER(72, 2, etherStatsCollisions), + RTL8365MB_MAKE_MIB_COUNTER(74, 2, dot3StatsExcessiveCollisions), + RTL8365MB_MAKE_MIB_COUNTER(76, 2, dot3OutPauseFrames), + RTL8365MB_MAKE_MIB_COUNTER(78, 2, ifOutDiscards), + RTL8365MB_MAKE_MIB_COUNTER(80, 2, dot1dTpPortInDiscards), + RTL8365MB_MAKE_MIB_COUNTER(82, 2, ifOutUcastPkts), + RTL8365MB_MAKE_MIB_COUNTER(84, 2, ifOutMulticastPkts), + RTL8365MB_MAKE_MIB_COUNTER(86, 2, ifOutBroadcastPkts), + RTL8365MB_MAKE_MIB_COUNTER(88, 2, outOampduPkts), + RTL8365MB_MAKE_MIB_COUNTER(90, 2, inOampduPkts), + RTL8365MB_MAKE_MIB_COUNTER(92, 4, inIgmpJoinsSuccess), + RTL8365MB_MAKE_MIB_COUNTER(96, 2, inIgmpJoinsFail), + RTL8365MB_MAKE_MIB_COUNTER(98, 2, inMldJoinsSuccess), + RTL8365MB_MAKE_MIB_COUNTER(100, 2, inMldJoinsFail), + RTL8365MB_MAKE_MIB_COUNTER(102, 2, inReportSuppressionDrop), + RTL8365MB_MAKE_MIB_COUNTER(104, 2, inLeaveSuppressionDrop), + RTL8365MB_MAKE_MIB_COUNTER(106, 2, outIgmpReports), + RTL8365MB_MAKE_MIB_COUNTER(108, 2, outIgmpLeaves), + RTL8365MB_MAKE_MIB_COUNTER(110, 2, outIgmpGeneralQuery), + RTL8365MB_MAKE_MIB_COUNTER(112, 2, outIgmpSpecificQuery), + RTL8365MB_MAKE_MIB_COUNTER(114, 2, outMldReports), + RTL8365MB_MAKE_MIB_COUNTER(116, 2, outMldLeaves), + RTL8365MB_MAKE_MIB_COUNTER(118, 2, outMldGeneralQuery), + RTL8365MB_MAKE_MIB_COUNTER(120, 2, outMldSpecificQuery), + RTL8365MB_MAKE_MIB_COUNTER(122, 2, inKnownMulticastPkts), +}; + +static_assert(ARRAY_SIZE(rtl8365mb_mib_counters) == RTL8365MB_MIB_END); + +struct rtl8365mb_jam_tbl_entry { + u16 reg; + u16 val; +}; + +/* Lifted from the vendor driver sources */ +static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_8365mb_vc[] = { + { 0x13EB, 0x15BB }, { 0x1303, 0x06D6 }, { 0x1304, 0x0700 }, + { 0x13E2, 0x003F }, { 0x13F9, 0x0090 }, { 0x121E, 0x03CA }, + { 0x1233, 0x0352 }, { 0x1237, 0x00A0 }, { 0x123A, 0x0030 }, + { 0x1239, 0x0084 }, { 0x0301, 0x1000 }, { 0x1349, 0x001F }, + { 0x18E0, 0x4004 }, { 0x122B, 0x241C }, { 0x1305, 0xC000 }, + { 0x13F0, 0x0000 }, +}; + +static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_common[] = { + { 0x1200, 0x7FCB }, { 0x0884, 0x0003 }, { 0x06EB, 0x0001 }, + { 0x03Fa, 0x0007 }, { 0x08C8, 0x00C0 }, { 0x0A30, 0x020E }, + { 0x0800, 0x0000 }, { 0x0802, 0x0000 }, { 0x09DA, 0x0013 }, + { 0x1D32, 0x0002 }, +}; + +enum rtl8365mb_stp_state { + RTL8365MB_STP_STATE_DISABLED = 0, + RTL8365MB_STP_STATE_BLOCKING = 1, + RTL8365MB_STP_STATE_LEARNING = 2, + RTL8365MB_STP_STATE_FORWARDING = 3, +}; + +enum rtl8365mb_cpu_insert { + RTL8365MB_CPU_INSERT_TO_ALL = 0, + RTL8365MB_CPU_INSERT_TO_TRAPPING = 1, + RTL8365MB_CPU_INSERT_TO_NONE = 2, +}; + +enum rtl8365mb_cpu_position { + RTL8365MB_CPU_POS_AFTER_SA = 0, + RTL8365MB_CPU_POS_BEFORE_CRC = 1, +}; + +enum rtl8365mb_cpu_format { + RTL8365MB_CPU_FORMAT_8BYTES = 0, + RTL8365MB_CPU_FORMAT_4BYTES = 1, +}; + +enum rtl8365mb_cpu_rxlen { + RTL8365MB_CPU_RXLEN_72BYTES = 0, + RTL8365MB_CPU_RXLEN_64BYTES = 1, +}; + +/** + * struct rtl8365mb_cpu - CPU port configuration + * @enable: enable/disable hardware insertion of CPU tag in switch->CPU frames + * @mask: port mask of ports that parse should parse CPU tags + * @trap_port: forward trapped frames to this port + * @insert: CPU tag insertion mode in switch->CPU frames + * @position: position of CPU tag in frame + * @rx_length: minimum CPU RX length + * @format: CPU tag format + * + * Represents the CPU tagging and CPU port configuration of the switch. These + * settings are configurable at runtime. + */ +struct rtl8365mb_cpu { + bool enable; + u32 mask; + u32 trap_port; + enum rtl8365mb_cpu_insert insert; + enum rtl8365mb_cpu_position position; + enum rtl8365mb_cpu_rxlen rx_length; + enum rtl8365mb_cpu_format format; +}; + +/** + * struct rtl8365mb_port - private per-port data + * @priv: pointer to parent realtek_priv data + * @index: DSA port index, same as dsa_port::index + * @stats: link statistics populated by rtl8365mb_stats_poll, ready for atomic + * access via rtl8365mb_get_stats64 + * @stats_lock: protect the stats structure during read/update + * @mib_work: delayed work for polling MIB counters + */ +struct rtl8365mb_port { + struct realtek_priv *priv; + unsigned int index; + struct rtnl_link_stats64 stats; + spinlock_t stats_lock; + struct delayed_work mib_work; +}; + +/** + * struct rtl8365mb - private chip-specific driver data + * @priv: pointer to parent realtek_priv data + * @irq: registered IRQ or zero + * @chip_id: chip identifier + * @chip_ver: chip silicon revision + * @port_mask: mask of all ports + * @learn_limit_max: maximum number of L2 addresses the chip can learn + * @cpu: CPU tagging and CPU port configuration for this chip + * @mib_lock: prevent concurrent reads of MIB counters + * @ports: per-port data + * @jam_table: chip-specific initialization jam table + * @jam_size: size of the chip's jam table + * + * Private data for this driver. + */ +struct rtl8365mb { + struct realtek_priv *priv; + int irq; + u32 chip_id; + u32 chip_ver; + u32 port_mask; + u32 learn_limit_max; + struct rtl8365mb_cpu cpu; + struct mutex mib_lock; + struct rtl8365mb_port ports[RTL8365MB_MAX_NUM_PORTS]; + const struct rtl8365mb_jam_tbl_entry *jam_table; + size_t jam_size; +}; + +static int rtl8365mb_phy_poll_busy(struct realtek_priv *priv) +{ + u32 val; + + return regmap_read_poll_timeout(priv->map_nolock, + RTL8365MB_INDIRECT_ACCESS_STATUS_REG, + val, !val, 10, 100); +} + +static int rtl8365mb_phy_ocp_prepare(struct realtek_priv *priv, int phy, + u32 ocp_addr) +{ + u32 val; + int ret; + + /* Set OCP prefix */ + val = FIELD_GET(RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK, ocp_addr); + ret = regmap_update_bits( + priv->map_nolock, RTL8365MB_GPHY_OCP_MSB_0_REG, + RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK, + FIELD_PREP(RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK, val)); + if (ret) + return ret; + + /* Set PHY register address */ + val = RTL8365MB_PHY_BASE; + val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK, phy); + val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK, + ocp_addr >> 1); + val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK, + ocp_addr >> 6); + ret = regmap_write(priv->map_nolock, + RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG, val); + if (ret) + return ret; + + return 0; +} + +static int rtl8365mb_phy_ocp_read(struct realtek_priv *priv, int phy, + u32 ocp_addr, u16 *data) +{ + u32 val; + int ret; + + mutex_lock(&priv->map_lock); + + ret = rtl8365mb_phy_poll_busy(priv); + if (ret) + goto out; + + ret = rtl8365mb_phy_ocp_prepare(priv, phy, ocp_addr); + if (ret) + goto out; + + /* Execute read operation */ + val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK, + RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) | + FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK, + RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ); + ret = regmap_write(priv->map_nolock, RTL8365MB_INDIRECT_ACCESS_CTRL_REG, + val); + if (ret) + goto out; + + ret = rtl8365mb_phy_poll_busy(priv); + if (ret) + goto out; + + /* Get PHY register data */ + ret = regmap_read(priv->map_nolock, + RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG, &val); + if (ret) + goto out; + + *data = val & 0xFFFF; + +out: + mutex_unlock(&priv->map_lock); + + return ret; +} + +static int rtl8365mb_phy_ocp_write(struct realtek_priv *priv, int phy, + u32 ocp_addr, u16 data) +{ + u32 val; + int ret; + + mutex_lock(&priv->map_lock); + + ret = rtl8365mb_phy_poll_busy(priv); + if (ret) + goto out; + + ret = rtl8365mb_phy_ocp_prepare(priv, phy, ocp_addr); + if (ret) + goto out; + + /* Set PHY register data */ + ret = regmap_write(priv->map_nolock, + RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG, data); + if (ret) + goto out; + + /* Execute write operation */ + val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK, + RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) | + FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK, + RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE); + ret = regmap_write(priv->map_nolock, RTL8365MB_INDIRECT_ACCESS_CTRL_REG, + val); + if (ret) + goto out; + + ret = rtl8365mb_phy_poll_busy(priv); + if (ret) + goto out; + +out: + mutex_unlock(&priv->map_lock); + + return 0; +} + +static int rtl8365mb_phy_read(struct realtek_priv *priv, int phy, int regnum) +{ + u32 ocp_addr; + u16 val; + int ret; + + if (phy > RTL8365MB_PHYADDRMAX) + return -EINVAL; + + if (regnum > RTL8365MB_PHYREGMAX) + return -EINVAL; + + ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2; + + ret = rtl8365mb_phy_ocp_read(priv, phy, ocp_addr, &val); + if (ret) { + dev_err(priv->dev, + "failed to read PHY%d reg %02x @ %04x, ret %d\n", phy, + regnum, ocp_addr, ret); + return ret; + } + + dev_dbg(priv->dev, "read PHY%d register 0x%02x @ %04x, val <- %04x\n", + phy, regnum, ocp_addr, val); + + return val; +} + +static int rtl8365mb_phy_write(struct realtek_priv *priv, int phy, int regnum, + u16 val) +{ + u32 ocp_addr; + int ret; + + if (phy > RTL8365MB_PHYADDRMAX) + return -EINVAL; + + if (regnum > RTL8365MB_PHYREGMAX) + return -EINVAL; + + ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2; + + ret = rtl8365mb_phy_ocp_write(priv, phy, ocp_addr, val); + if (ret) { + dev_err(priv->dev, + "failed to write PHY%d reg %02x @ %04x, ret %d\n", phy, + regnum, ocp_addr, ret); + return ret; + } + + dev_dbg(priv->dev, "write PHY%d register 0x%02x @ %04x, val -> %04x\n", + phy, regnum, ocp_addr, val); + + return 0; +} + +static int rtl8365mb_dsa_phy_read(struct dsa_switch *ds, int phy, int regnum) +{ + return rtl8365mb_phy_read(ds->priv, phy, regnum); +} + +static int rtl8365mb_dsa_phy_write(struct dsa_switch *ds, int phy, int regnum, + u16 val) +{ + return rtl8365mb_phy_write(ds->priv, phy, regnum, val); +} + +static enum dsa_tag_protocol +rtl8365mb_get_tag_protocol(struct dsa_switch *ds, int port, + enum dsa_tag_protocol mp) +{ + struct realtek_priv *priv = ds->priv; + struct rtl8365mb_cpu *cpu; + struct rtl8365mb *mb; + + mb = priv->chip_data; + cpu = &mb->cpu; + + if (cpu->position == RTL8365MB_CPU_POS_BEFORE_CRC) + return DSA_TAG_PROTO_RTL8_4T; + + return DSA_TAG_PROTO_RTL8_4; +} + +static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port, + phy_interface_t interface) +{ + struct device_node *dn; + struct dsa_port *dp; + int tx_delay = 0; + int rx_delay = 0; + int ext_int; + u32 val; + int ret; + + ext_int = rtl8365mb_extint_port_map[port]; + + if (ext_int <= 0) { + dev_err(priv->dev, "Port %d is not an external interface port\n", port); + return -EINVAL; + } + + dp = dsa_to_port(priv->ds, port); + dn = dp->dn; + + /* Set the RGMII TX/RX delay + * + * The Realtek vendor driver indicates the following possible + * configuration settings: + * + * TX delay: + * 0 = no delay, 1 = 2 ns delay + * RX delay: + * 0 = no delay, 7 = maximum delay + * Each step is approximately 0.3 ns, so the maximum delay is about + * 2.1 ns. + * + * The vendor driver also states that this must be configured *before* + * forcing the external interface into a particular mode, which is done + * in the rtl8365mb_phylink_mac_link_{up,down} functions. + * + * Only configure an RGMII TX (resp. RX) delay if the + * tx-internal-delay-ps (resp. rx-internal-delay-ps) OF property is + * specified. We ignore the detail of the RGMII interface mode + * (RGMII_{RXID, TXID, etc.}), as this is considered to be a PHY-only + * property. + */ + if (!of_property_read_u32(dn, "tx-internal-delay-ps", &val)) { + val = val / 1000; /* convert to ns */ + + if (val == 0 || val == 2) + tx_delay = val / 2; + else + dev_warn(priv->dev, + "EXT interface TX delay must be 0 or 2 ns\n"); + } + + if (!of_property_read_u32(dn, "rx-internal-delay-ps", &val)) { + val = DIV_ROUND_CLOSEST(val, 300); /* convert to 0.3 ns step */ + + if (val <= 7) + rx_delay = val; + else + dev_warn(priv->dev, + "EXT interface RX delay must be 0 to 2.1 ns\n"); + } + + ret = regmap_update_bits( + priv->map, RTL8365MB_EXT_RGMXF_REG(ext_int), + RTL8365MB_EXT_RGMXF_TXDELAY_MASK | + RTL8365MB_EXT_RGMXF_RXDELAY_MASK, + FIELD_PREP(RTL8365MB_EXT_RGMXF_TXDELAY_MASK, tx_delay) | + FIELD_PREP(RTL8365MB_EXT_RGMXF_RXDELAY_MASK, rx_delay)); + if (ret) + return ret; + + ret = regmap_update_bits( + priv->map, RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(ext_int), + RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(ext_int), + RTL8365MB_EXT_PORT_MODE_RGMII + << RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET( + ext_int)); + if (ret) + return ret; + + return 0; +} + +static int rtl8365mb_ext_config_forcemode(struct realtek_priv *priv, int port, + bool link, int speed, int duplex, + bool tx_pause, bool rx_pause) +{ + u32 r_tx_pause; + u32 r_rx_pause; + u32 r_duplex; + u32 r_speed; + u32 r_link; + int ext_int; + int val; + int ret; + + ext_int = rtl8365mb_extint_port_map[port]; + + if (ext_int <= 0) { + dev_err(priv->dev, "Port %d is not an external interface port\n", port); + return -EINVAL; + } + + if (link) { + /* Force the link up with the desired configuration */ + r_link = 1; + r_rx_pause = rx_pause ? 1 : 0; + r_tx_pause = tx_pause ? 1 : 0; + + if (speed == SPEED_1000) { + r_speed = RTL8365MB_PORT_SPEED_1000M; + } else if (speed == SPEED_100) { + r_speed = RTL8365MB_PORT_SPEED_100M; + } else if (speed == SPEED_10) { + r_speed = RTL8365MB_PORT_SPEED_10M; + } else { + dev_err(priv->dev, "unsupported port speed %s\n", + phy_speed_to_str(speed)); + return -EINVAL; + } + + if (duplex == DUPLEX_FULL) { + r_duplex = 1; + } else if (duplex == DUPLEX_HALF) { + r_duplex = 0; + } else { + dev_err(priv->dev, "unsupported duplex %s\n", + phy_duplex_to_str(duplex)); + return -EINVAL; + } + } else { + /* Force the link down and reset any programmed configuration */ + r_link = 0; + r_tx_pause = 0; + r_rx_pause = 0; + r_speed = 0; + r_duplex = 0; + } + + val = FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK, 1) | + FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK, + r_tx_pause) | + FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK, + r_rx_pause) | + FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK, r_link) | + FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK, + r_duplex) | + FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK, r_speed); + ret = regmap_write(priv->map, + RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(ext_int), + val); + if (ret) + return ret; + + return 0; +} + +static bool rtl8365mb_phy_mode_supported(struct dsa_switch *ds, int port, + phy_interface_t interface) +{ + int ext_int; + + ext_int = rtl8365mb_extint_port_map[port]; + + if (ext_int < 0 && + (interface == PHY_INTERFACE_MODE_NA || + interface == PHY_INTERFACE_MODE_INTERNAL || + interface == PHY_INTERFACE_MODE_GMII)) + /* Internal PHY */ + return true; + else if ((ext_int >= 1) && + phy_interface_mode_is_rgmii(interface)) + /* Extension MAC */ + return true; + + return false; +} + +static void rtl8365mb_phylink_get_caps(struct dsa_switch *ds, int port, + struct phylink_config *config) +{ + if (dsa_is_user_port(ds, port)) + __set_bit(PHY_INTERFACE_MODE_INTERNAL, + config->supported_interfaces); + else if (dsa_is_cpu_port(ds, port)) + phy_interface_set_rgmii(config->supported_interfaces); + + config->mac_capabilities = MAC_SYM_PAUSE | MAC_ASYM_PAUSE | + MAC_10 | MAC_100 | MAC_1000FD; +} + +static void rtl8365mb_phylink_mac_config(struct dsa_switch *ds, int port, + unsigned int mode, + const struct phylink_link_state *state) +{ + struct realtek_priv *priv = ds->priv; + int ret; + + if (!rtl8365mb_phy_mode_supported(ds, port, state->interface)) { + dev_err(priv->dev, "phy mode %s is unsupported on port %d\n", + phy_modes(state->interface), port); + return; + } + + if (mode != MLO_AN_PHY && mode != MLO_AN_FIXED) { + dev_err(priv->dev, + "port %d supports only conventional PHY or fixed-link\n", + port); + return; + } + + if (phy_interface_mode_is_rgmii(state->interface)) { + ret = rtl8365mb_ext_config_rgmii(priv, port, state->interface); + if (ret) + dev_err(priv->dev, + "failed to configure RGMII mode on port %d: %d\n", + port, ret); + return; + } + + /* TODO: Implement MII and RMII modes, which the RTL8365MB-VC also + * supports + */ +} + +static void rtl8365mb_phylink_mac_link_down(struct dsa_switch *ds, int port, + unsigned int mode, + phy_interface_t interface) +{ + struct realtek_priv *priv = ds->priv; + struct rtl8365mb_port *p; + struct rtl8365mb *mb; + int ret; + + mb = priv->chip_data; + p = &mb->ports[port]; + cancel_delayed_work_sync(&p->mib_work); + + if (phy_interface_mode_is_rgmii(interface)) { + ret = rtl8365mb_ext_config_forcemode(priv, port, false, 0, 0, + false, false); + if (ret) + dev_err(priv->dev, + "failed to reset forced mode on port %d: %d\n", + port, ret); + + return; + } +} + +static void rtl8365mb_phylink_mac_link_up(struct dsa_switch *ds, int port, + unsigned int mode, + phy_interface_t interface, + struct phy_device *phydev, int speed, + int duplex, bool tx_pause, + bool rx_pause) +{ + struct realtek_priv *priv = ds->priv; + struct rtl8365mb_port *p; + struct rtl8365mb *mb; + int ret; + + mb = priv->chip_data; + p = &mb->ports[port]; + schedule_delayed_work(&p->mib_work, 0); + + if (phy_interface_mode_is_rgmii(interface)) { + ret = rtl8365mb_ext_config_forcemode(priv, port, true, speed, + duplex, tx_pause, + rx_pause); + if (ret) + dev_err(priv->dev, + "failed to force mode on port %d: %d\n", port, + ret); + + return; + } +} + +static void rtl8365mb_port_stp_state_set(struct dsa_switch *ds, int port, + u8 state) +{ + struct realtek_priv *priv = ds->priv; + enum rtl8365mb_stp_state val; + int msti = 0; + + switch (state) { + case BR_STATE_DISABLED: + val = RTL8365MB_STP_STATE_DISABLED; + break; + case BR_STATE_BLOCKING: + case BR_STATE_LISTENING: + val = RTL8365MB_STP_STATE_BLOCKING; + break; + case BR_STATE_LEARNING: + val = RTL8365MB_STP_STATE_LEARNING; + break; + case BR_STATE_FORWARDING: + val = RTL8365MB_STP_STATE_FORWARDING; + break; + default: + dev_err(priv->dev, "invalid STP state: %u\n", state); + return; + } + + regmap_update_bits(priv->map, RTL8365MB_MSTI_CTRL_REG(msti, port), + RTL8365MB_MSTI_CTRL_PORT_STATE_MASK(port), + val << RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET(port)); +} + +static int rtl8365mb_port_set_learning(struct realtek_priv *priv, int port, + bool enable) +{ + struct rtl8365mb *mb = priv->chip_data; + + /* Enable/disable learning by limiting the number of L2 addresses the + * port can learn. Realtek documentation states that a limit of zero + * disables learning. When enabling learning, set it to the chip's + * maximum. + */ + return regmap_write(priv->map, RTL8365MB_LUT_PORT_LEARN_LIMIT_REG(port), + enable ? mb->learn_limit_max : 0); +} + +static int rtl8365mb_port_set_isolation(struct realtek_priv *priv, int port, + u32 mask) +{ + return regmap_write(priv->map, RTL8365MB_PORT_ISOLATION_REG(port), mask); +} + +static int rtl8365mb_mib_counter_read(struct realtek_priv *priv, int port, + u32 offset, u32 length, u64 *mibvalue) +{ + u64 tmpvalue = 0; + u32 val; + int ret; + int i; + + /* The MIB address is an SRAM address. We request a particular address + * and then poll the control register before reading the value from some + * counter registers. + */ + ret = regmap_write(priv->map, RTL8365MB_MIB_ADDRESS_REG, + RTL8365MB_MIB_ADDRESS(port, offset)); + if (ret) + return ret; + + /* Poll for completion */ + ret = regmap_read_poll_timeout(priv->map, RTL8365MB_MIB_CTRL0_REG, val, + !(val & RTL8365MB_MIB_CTRL0_BUSY_MASK), + 10, 100); + if (ret) + return ret; + + /* Presumably this indicates a MIB counter read failure */ + if (val & RTL8365MB_MIB_CTRL0_RESET_MASK) + return -EIO; + + /* There are four MIB counter registers each holding a 16 bit word of a + * MIB counter. Depending on the offset, we should read from the upper + * two or lower two registers. In case the MIB counter is 4 words, we + * read from all four registers. + */ + if (length == 4) + offset = 3; + else + offset = (offset + 1) % 4; + + /* Read the MIB counter 16 bits at a time */ + for (i = 0; i < length; i++) { + ret = regmap_read(priv->map, + RTL8365MB_MIB_COUNTER_REG(offset - i), &val); + if (ret) + return ret; + + tmpvalue = ((tmpvalue) << 16) | (val & 0xFFFF); + } + + /* Only commit the result if no error occurred */ + *mibvalue = tmpvalue; + + return 0; +} + +static void rtl8365mb_get_ethtool_stats(struct dsa_switch *ds, int port, u64 *data) +{ + struct realtek_priv *priv = ds->priv; + struct rtl8365mb *mb; + int ret; + int i; + + mb = priv->chip_data; + + mutex_lock(&mb->mib_lock); + for (i = 0; i < RTL8365MB_MIB_END; i++) { + struct rtl8365mb_mib_counter *mib = &rtl8365mb_mib_counters[i]; + + ret = rtl8365mb_mib_counter_read(priv, port, mib->offset, + mib->length, &data[i]); + if (ret) { + dev_err(priv->dev, + "failed to read port %d counters: %d\n", port, + ret); + break; + } + } + mutex_unlock(&mb->mib_lock); +} + +static void rtl8365mb_get_strings(struct dsa_switch *ds, int port, u32 stringset, u8 *data) +{ + int i; + + if (stringset != ETH_SS_STATS) + return; + + for (i = 0; i < RTL8365MB_MIB_END; i++) { + struct rtl8365mb_mib_counter *mib = &rtl8365mb_mib_counters[i]; + + strncpy(data + i * ETH_GSTRING_LEN, mib->name, ETH_GSTRING_LEN); + } +} + +static int rtl8365mb_get_sset_count(struct dsa_switch *ds, int port, int sset) +{ + if (sset != ETH_SS_STATS) + return -EOPNOTSUPP; + + return RTL8365MB_MIB_END; +} + +static void rtl8365mb_get_phy_stats(struct dsa_switch *ds, int port, + struct ethtool_eth_phy_stats *phy_stats) +{ + struct realtek_priv *priv = ds->priv; + struct rtl8365mb_mib_counter *mib; + struct rtl8365mb *mb; + + mb = priv->chip_data; + mib = &rtl8365mb_mib_counters[RTL8365MB_MIB_dot3StatsSymbolErrors]; + + mutex_lock(&mb->mib_lock); + rtl8365mb_mib_counter_read(priv, port, mib->offset, mib->length, + &phy_stats->SymbolErrorDuringCarrier); + mutex_unlock(&mb->mib_lock); +} + +static void rtl8365mb_get_mac_stats(struct dsa_switch *ds, int port, + struct ethtool_eth_mac_stats *mac_stats) +{ + u64 cnt[RTL8365MB_MIB_END] = { + [RTL8365MB_MIB_ifOutOctets] = 1, + [RTL8365MB_MIB_ifOutUcastPkts] = 1, + [RTL8365MB_MIB_ifOutMulticastPkts] = 1, + [RTL8365MB_MIB_ifOutBroadcastPkts] = 1, + [RTL8365MB_MIB_dot3OutPauseFrames] = 1, + [RTL8365MB_MIB_ifOutDiscards] = 1, + [RTL8365MB_MIB_ifInOctets] = 1, + [RTL8365MB_MIB_ifInUcastPkts] = 1, + [RTL8365MB_MIB_ifInMulticastPkts] = 1, + [RTL8365MB_MIB_ifInBroadcastPkts] = 1, + [RTL8365MB_MIB_dot3InPauseFrames] = 1, + [RTL8365MB_MIB_dot3StatsSingleCollisionFrames] = 1, + [RTL8365MB_MIB_dot3StatsMultipleCollisionFrames] = 1, + [RTL8365MB_MIB_dot3StatsFCSErrors] = 1, + [RTL8365MB_MIB_dot3StatsDeferredTransmissions] = 1, + [RTL8365MB_MIB_dot3StatsLateCollisions] = 1, + [RTL8365MB_MIB_dot3StatsExcessiveCollisions] = 1, + + }; + struct realtek_priv *priv = ds->priv; + struct rtl8365mb *mb; + int ret; + int i; + + mb = priv->chip_data; + + mutex_lock(&mb->mib_lock); + for (i = 0; i < RTL8365MB_MIB_END; i++) { + struct rtl8365mb_mib_counter *mib = &rtl8365mb_mib_counters[i]; + + /* Only fetch required MIB counters (marked = 1 above) */ + if (!cnt[i]) + continue; + + ret = rtl8365mb_mib_counter_read(priv, port, mib->offset, + mib->length, &cnt[i]); + if (ret) + break; + } + mutex_unlock(&mb->mib_lock); + + /* The RTL8365MB-VC exposes MIB objects, which we have to translate into + * IEEE 802.3 Managed Objects. This is not always completely faithful, + * but we try out best. See RFC 3635 for a detailed treatment of the + * subject. + */ + + mac_stats->FramesTransmittedOK = cnt[RTL8365MB_MIB_ifOutUcastPkts] + + cnt[RTL8365MB_MIB_ifOutMulticastPkts] + + cnt[RTL8365MB_MIB_ifOutBroadcastPkts] + + cnt[RTL8365MB_MIB_dot3OutPauseFrames] - + cnt[RTL8365MB_MIB_ifOutDiscards]; + mac_stats->SingleCollisionFrames = + cnt[RTL8365MB_MIB_dot3StatsSingleCollisionFrames]; + mac_stats->MultipleCollisionFrames = + cnt[RTL8365MB_MIB_dot3StatsMultipleCollisionFrames]; + mac_stats->FramesReceivedOK = cnt[RTL8365MB_MIB_ifInUcastPkts] + + cnt[RTL8365MB_MIB_ifInMulticastPkts] + + cnt[RTL8365MB_MIB_ifInBroadcastPkts] + + cnt[RTL8365MB_MIB_dot3InPauseFrames]; + mac_stats->FrameCheckSequenceErrors = + cnt[RTL8365MB_MIB_dot3StatsFCSErrors]; + mac_stats->OctetsTransmittedOK = cnt[RTL8365MB_MIB_ifOutOctets] - + 18 * mac_stats->FramesTransmittedOK; + mac_stats->FramesWithDeferredXmissions = + cnt[RTL8365MB_MIB_dot3StatsDeferredTransmissions]; + mac_stats->LateCollisions = cnt[RTL8365MB_MIB_dot3StatsLateCollisions]; + mac_stats->FramesAbortedDueToXSColls = + cnt[RTL8365MB_MIB_dot3StatsExcessiveCollisions]; + mac_stats->OctetsReceivedOK = cnt[RTL8365MB_MIB_ifInOctets] - + 18 * mac_stats->FramesReceivedOK; + mac_stats->MulticastFramesXmittedOK = + cnt[RTL8365MB_MIB_ifOutMulticastPkts]; + mac_stats->BroadcastFramesXmittedOK = + cnt[RTL8365MB_MIB_ifOutBroadcastPkts]; + mac_stats->MulticastFramesReceivedOK = + cnt[RTL8365MB_MIB_ifInMulticastPkts]; + mac_stats->BroadcastFramesReceivedOK = + cnt[RTL8365MB_MIB_ifInBroadcastPkts]; +} + +static void rtl8365mb_get_ctrl_stats(struct dsa_switch *ds, int port, + struct ethtool_eth_ctrl_stats *ctrl_stats) +{ + struct realtek_priv *priv = ds->priv; + struct rtl8365mb_mib_counter *mib; + struct rtl8365mb *mb; + + mb = priv->chip_data; + mib = &rtl8365mb_mib_counters[RTL8365MB_MIB_dot3ControlInUnknownOpcodes]; + + mutex_lock(&mb->mib_lock); + rtl8365mb_mib_counter_read(priv, port, mib->offset, mib->length, + &ctrl_stats->UnsupportedOpcodesReceived); + mutex_unlock(&mb->mib_lock); +} + +static void rtl8365mb_stats_update(struct realtek_priv *priv, int port) +{ + u64 cnt[RTL8365MB_MIB_END] = { + [RTL8365MB_MIB_ifOutOctets] = 1, + [RTL8365MB_MIB_ifOutUcastPkts] = 1, + [RTL8365MB_MIB_ifOutMulticastPkts] = 1, + [RTL8365MB_MIB_ifOutBroadcastPkts] = 1, + [RTL8365MB_MIB_ifOutDiscards] = 1, + [RTL8365MB_MIB_ifInOctets] = 1, + [RTL8365MB_MIB_ifInUcastPkts] = 1, + [RTL8365MB_MIB_ifInMulticastPkts] = 1, + [RTL8365MB_MIB_ifInBroadcastPkts] = 1, + [RTL8365MB_MIB_etherStatsDropEvents] = 1, + [RTL8365MB_MIB_etherStatsCollisions] = 1, + [RTL8365MB_MIB_etherStatsFragments] = 1, + [RTL8365MB_MIB_etherStatsJabbers] = 1, + [RTL8365MB_MIB_dot3StatsFCSErrors] = 1, + [RTL8365MB_MIB_dot3StatsLateCollisions] = 1, + }; + struct rtl8365mb *mb = priv->chip_data; + struct rtnl_link_stats64 *stats; + int ret; + int i; + + stats = &mb->ports[port].stats; + + mutex_lock(&mb->mib_lock); + for (i = 0; i < RTL8365MB_MIB_END; i++) { + struct rtl8365mb_mib_counter *c = &rtl8365mb_mib_counters[i]; + + /* Only fetch required MIB counters (marked = 1 above) */ + if (!cnt[i]) + continue; + + ret = rtl8365mb_mib_counter_read(priv, port, c->offset, + c->length, &cnt[i]); + if (ret) + break; + } + mutex_unlock(&mb->mib_lock); + + /* Don't update statistics if there was an error reading the counters */ + if (ret) + return; + + spin_lock(&mb->ports[port].stats_lock); + + stats->rx_packets = cnt[RTL8365MB_MIB_ifInUcastPkts] + + cnt[RTL8365MB_MIB_ifInMulticastPkts] + + cnt[RTL8365MB_MIB_ifInBroadcastPkts] - + cnt[RTL8365MB_MIB_ifOutDiscards]; + + stats->tx_packets = cnt[RTL8365MB_MIB_ifOutUcastPkts] + + cnt[RTL8365MB_MIB_ifOutMulticastPkts] + + cnt[RTL8365MB_MIB_ifOutBroadcastPkts]; + + /* if{In,Out}Octets includes FCS - remove it */ + stats->rx_bytes = cnt[RTL8365MB_MIB_ifInOctets] - 4 * stats->rx_packets; + stats->tx_bytes = + cnt[RTL8365MB_MIB_ifOutOctets] - 4 * stats->tx_packets; + + stats->rx_dropped = cnt[RTL8365MB_MIB_etherStatsDropEvents]; + stats->tx_dropped = cnt[RTL8365MB_MIB_ifOutDiscards]; + + stats->multicast = cnt[RTL8365MB_MIB_ifInMulticastPkts]; + stats->collisions = cnt[RTL8365MB_MIB_etherStatsCollisions]; + + stats->rx_length_errors = cnt[RTL8365MB_MIB_etherStatsFragments] + + cnt[RTL8365MB_MIB_etherStatsJabbers]; + stats->rx_crc_errors = cnt[RTL8365MB_MIB_dot3StatsFCSErrors]; + stats->rx_errors = stats->rx_length_errors + stats->rx_crc_errors; + + stats->tx_aborted_errors = cnt[RTL8365MB_MIB_ifOutDiscards]; + stats->tx_window_errors = cnt[RTL8365MB_MIB_dot3StatsLateCollisions]; + stats->tx_errors = stats->tx_aborted_errors + stats->tx_window_errors; + + spin_unlock(&mb->ports[port].stats_lock); +} + +static void rtl8365mb_stats_poll(struct work_struct *work) +{ + struct rtl8365mb_port *p = container_of(to_delayed_work(work), + struct rtl8365mb_port, + mib_work); + struct realtek_priv *priv = p->priv; + + rtl8365mb_stats_update(priv, p->index); + + schedule_delayed_work(&p->mib_work, RTL8365MB_STATS_INTERVAL_JIFFIES); +} + +static void rtl8365mb_get_stats64(struct dsa_switch *ds, int port, + struct rtnl_link_stats64 *s) +{ + struct realtek_priv *priv = ds->priv; + struct rtl8365mb_port *p; + struct rtl8365mb *mb; + + mb = priv->chip_data; + p = &mb->ports[port]; + + spin_lock(&p->stats_lock); + memcpy(s, &p->stats, sizeof(*s)); + spin_unlock(&p->stats_lock); +} + +static void rtl8365mb_stats_setup(struct realtek_priv *priv) +{ + struct rtl8365mb *mb = priv->chip_data; + int i; + + /* Per-chip global mutex to protect MIB counter access, since doing + * so requires accessing a series of registers in a particular order. + */ + mutex_init(&mb->mib_lock); + + for (i = 0; i < priv->num_ports; i++) { + struct rtl8365mb_port *p = &mb->ports[i]; + + if (dsa_is_unused_port(priv->ds, i)) + continue; + + /* Per-port spinlock to protect the stats64 data */ + spin_lock_init(&p->stats_lock); + + /* This work polls the MIB counters and keeps the stats64 data + * up-to-date. + */ + INIT_DELAYED_WORK(&p->mib_work, rtl8365mb_stats_poll); + } +} + +static void rtl8365mb_stats_teardown(struct realtek_priv *priv) +{ + struct rtl8365mb *mb = priv->chip_data; + int i; + + for (i = 0; i < priv->num_ports; i++) { + struct rtl8365mb_port *p = &mb->ports[i]; + + if (dsa_is_unused_port(priv->ds, i)) + continue; + + cancel_delayed_work_sync(&p->mib_work); + } +} + +static int rtl8365mb_get_and_clear_status_reg(struct realtek_priv *priv, u32 reg, + u32 *val) +{ + int ret; + + ret = regmap_read(priv->map, reg, val); + if (ret) + return ret; + + return regmap_write(priv->map, reg, *val); +} + +static irqreturn_t rtl8365mb_irq(int irq, void *data) +{ + struct realtek_priv *priv = data; + unsigned long line_changes = 0; + struct rtl8365mb *mb; + u32 stat; + int line; + int ret; + + mb = priv->chip_data; + + ret = rtl8365mb_get_and_clear_status_reg(priv, RTL8365MB_INTR_STATUS_REG, + &stat); + if (ret) + goto out_error; + + if (stat & RTL8365MB_INTR_LINK_CHANGE_MASK) { + u32 linkdown_ind; + u32 linkup_ind; + u32 val; + + ret = rtl8365mb_get_and_clear_status_reg( + priv, RTL8365MB_PORT_LINKUP_IND_REG, &val); + if (ret) + goto out_error; + + linkup_ind = FIELD_GET(RTL8365MB_PORT_LINKUP_IND_MASK, val); + + ret = rtl8365mb_get_and_clear_status_reg( + priv, RTL8365MB_PORT_LINKDOWN_IND_REG, &val); + if (ret) + goto out_error; + + linkdown_ind = FIELD_GET(RTL8365MB_PORT_LINKDOWN_IND_MASK, val); + + line_changes = (linkup_ind | linkdown_ind) & mb->port_mask; + } + + if (!line_changes) + goto out_none; + + for_each_set_bit(line, &line_changes, priv->num_ports) { + int child_irq = irq_find_mapping(priv->irqdomain, line); + + handle_nested_irq(child_irq); + } + + return IRQ_HANDLED; + +out_error: + dev_err(priv->dev, "failed to read interrupt status: %d\n", ret); + +out_none: + return IRQ_NONE; +} + +static struct irq_chip rtl8365mb_irq_chip = { + .name = "rtl8365mb", + /* The hardware doesn't support masking IRQs on a per-port basis */ +}; + +static int rtl8365mb_irq_map(struct irq_domain *domain, unsigned int irq, + irq_hw_number_t hwirq) +{ + irq_set_chip_data(irq, domain->host_data); + irq_set_chip_and_handler(irq, &rtl8365mb_irq_chip, handle_simple_irq); + irq_set_nested_thread(irq, 1); + irq_set_noprobe(irq); + + return 0; +} + +static void rtl8365mb_irq_unmap(struct irq_domain *d, unsigned int irq) +{ + irq_set_nested_thread(irq, 0); + irq_set_chip_and_handler(irq, NULL, NULL); + irq_set_chip_data(irq, NULL); +} + +static const struct irq_domain_ops rtl8365mb_irqdomain_ops = { + .map = rtl8365mb_irq_map, + .unmap = rtl8365mb_irq_unmap, + .xlate = irq_domain_xlate_onecell, +}; + +static int rtl8365mb_set_irq_enable(struct realtek_priv *priv, bool enable) +{ + return regmap_update_bits(priv->map, RTL8365MB_INTR_CTRL_REG, + RTL8365MB_INTR_LINK_CHANGE_MASK, + FIELD_PREP(RTL8365MB_INTR_LINK_CHANGE_MASK, + enable ? 1 : 0)); +} + +static int rtl8365mb_irq_enable(struct realtek_priv *priv) +{ + return rtl8365mb_set_irq_enable(priv, true); +} + +static int rtl8365mb_irq_disable(struct realtek_priv *priv) +{ + return rtl8365mb_set_irq_enable(priv, false); +} + +static int rtl8365mb_irq_setup(struct realtek_priv *priv) +{ + struct rtl8365mb *mb = priv->chip_data; + struct device_node *intc; + u32 irq_trig; + int virq; + int irq; + u32 val; + int ret; + int i; + + intc = of_get_child_by_name(priv->dev->of_node, "interrupt-controller"); + if (!intc) { + dev_err(priv->dev, "missing child interrupt-controller node\n"); + return -EINVAL; + } + + /* rtl8365mb IRQs cascade off this one */ + irq = of_irq_get(intc, 0); + if (irq <= 0) { + if (irq != -EPROBE_DEFER) + dev_err(priv->dev, "failed to get parent irq: %d\n", + irq); + ret = irq ? irq : -EINVAL; + goto out_put_node; + } + + priv->irqdomain = irq_domain_add_linear(intc, priv->num_ports, + &rtl8365mb_irqdomain_ops, priv); + if (!priv->irqdomain) { + dev_err(priv->dev, "failed to add irq domain\n"); + ret = -ENOMEM; + goto out_put_node; + } + + for (i = 0; i < priv->num_ports; i++) { + virq = irq_create_mapping(priv->irqdomain, i); + if (!virq) { + dev_err(priv->dev, + "failed to create irq domain mapping\n"); + ret = -EINVAL; + goto out_remove_irqdomain; + } + + irq_set_parent(virq, irq); + } + + /* Configure chip interrupt signal polarity */ + irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq)); + switch (irq_trig) { + case IRQF_TRIGGER_RISING: + case IRQF_TRIGGER_HIGH: + val = RTL8365MB_INTR_POLARITY_HIGH; + break; + case IRQF_TRIGGER_FALLING: + case IRQF_TRIGGER_LOW: + val = RTL8365MB_INTR_POLARITY_LOW; + break; + default: + dev_err(priv->dev, "unsupported irq trigger type %u\n", + irq_trig); + ret = -EINVAL; + goto out_remove_irqdomain; + } + + ret = regmap_update_bits(priv->map, RTL8365MB_INTR_POLARITY_REG, + RTL8365MB_INTR_POLARITY_MASK, + FIELD_PREP(RTL8365MB_INTR_POLARITY_MASK, val)); + if (ret) + goto out_remove_irqdomain; + + /* Disable the interrupt in case the chip has it enabled on reset */ + ret = rtl8365mb_irq_disable(priv); + if (ret) + goto out_remove_irqdomain; + + /* Clear the interrupt status register */ + ret = regmap_write(priv->map, RTL8365MB_INTR_STATUS_REG, + RTL8365MB_INTR_ALL_MASK); + if (ret) + goto out_remove_irqdomain; + + ret = request_threaded_irq(irq, NULL, rtl8365mb_irq, IRQF_ONESHOT, + "rtl8365mb", priv); + if (ret) { + dev_err(priv->dev, "failed to request irq: %d\n", ret); + goto out_remove_irqdomain; + } + + /* Store the irq so that we know to free it during teardown */ + mb->irq = irq; + + ret = rtl8365mb_irq_enable(priv); + if (ret) + goto out_free_irq; + + of_node_put(intc); + + return 0; + +out_free_irq: + free_irq(mb->irq, priv); + mb->irq = 0; + +out_remove_irqdomain: + for (i = 0; i < priv->num_ports; i++) { + virq = irq_find_mapping(priv->irqdomain, i); + irq_dispose_mapping(virq); + } + + irq_domain_remove(priv->irqdomain); + priv->irqdomain = NULL; + +out_put_node: + of_node_put(intc); + + return ret; +} + +static void rtl8365mb_irq_teardown(struct realtek_priv *priv) +{ + struct rtl8365mb *mb = priv->chip_data; + int virq; + int i; + + if (mb->irq) { + free_irq(mb->irq, priv); + mb->irq = 0; + } + + if (priv->irqdomain) { + for (i = 0; i < priv->num_ports; i++) { + virq = irq_find_mapping(priv->irqdomain, i); + irq_dispose_mapping(virq); + } + + irq_domain_remove(priv->irqdomain); + priv->irqdomain = NULL; + } +} + +static int rtl8365mb_cpu_config(struct realtek_priv *priv) +{ + struct rtl8365mb *mb = priv->chip_data; + struct rtl8365mb_cpu *cpu = &mb->cpu; + u32 val; + int ret; + + ret = regmap_update_bits(priv->map, RTL8365MB_CPU_PORT_MASK_REG, + RTL8365MB_CPU_PORT_MASK_MASK, + FIELD_PREP(RTL8365MB_CPU_PORT_MASK_MASK, + cpu->mask)); + if (ret) + return ret; + + val = FIELD_PREP(RTL8365MB_CPU_CTRL_EN_MASK, cpu->enable ? 1 : 0) | + FIELD_PREP(RTL8365MB_CPU_CTRL_INSERTMODE_MASK, cpu->insert) | + FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_POSITION_MASK, cpu->position) | + FIELD_PREP(RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK, cpu->rx_length) | + FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK, cpu->format) | + FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_MASK, cpu->trap_port & 0x7) | + FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK, + cpu->trap_port >> 3 & 0x1); + ret = regmap_write(priv->map, RTL8365MB_CPU_CTRL_REG, val); + if (ret) + return ret; + + return 0; +} + +static int rtl8365mb_change_tag_protocol(struct dsa_switch *ds, int cpu_index, + enum dsa_tag_protocol proto) +{ + struct realtek_priv *priv = ds->priv; + struct rtl8365mb_cpu *cpu; + struct rtl8365mb *mb; + + mb = priv->chip_data; + cpu = &mb->cpu; + + switch (proto) { + case DSA_TAG_PROTO_RTL8_4: + cpu->format = RTL8365MB_CPU_FORMAT_8BYTES; + cpu->position = RTL8365MB_CPU_POS_AFTER_SA; + break; + case DSA_TAG_PROTO_RTL8_4T: + cpu->format = RTL8365MB_CPU_FORMAT_8BYTES; + cpu->position = RTL8365MB_CPU_POS_BEFORE_CRC; + break; + /* The switch also supports a 4-byte format, similar to rtl4a but with + * the same 0x04 8-bit version and probably 8-bit port source/dest. + * There is no public doc about it. Not supported yet and it will probably + * never be. + */ + default: + return -EPROTONOSUPPORT; + } + + return rtl8365mb_cpu_config(priv); +} + +static int rtl8365mb_switch_init(struct realtek_priv *priv) +{ + struct rtl8365mb *mb = priv->chip_data; + int ret; + int i; + + /* Do any chip-specific init jam before getting to the common stuff */ + if (mb->jam_table) { + for (i = 0; i < mb->jam_size; i++) { + ret = regmap_write(priv->map, mb->jam_table[i].reg, + mb->jam_table[i].val); + if (ret) + return ret; + } + } + + /* Common init jam */ + for (i = 0; i < ARRAY_SIZE(rtl8365mb_init_jam_common); i++) { + ret = regmap_write(priv->map, rtl8365mb_init_jam_common[i].reg, + rtl8365mb_init_jam_common[i].val); + if (ret) + return ret; + } + + return 0; +} + +static int rtl8365mb_reset_chip(struct realtek_priv *priv) +{ + u32 val; + + priv->write_reg_noack(priv, RTL8365MB_CHIP_RESET_REG, + FIELD_PREP(RTL8365MB_CHIP_RESET_HW_MASK, 1)); + + /* Realtek documentation says the chip needs 1 second to reset. Sleep + * for 100 ms before accessing any registers to prevent ACK timeouts. + */ + msleep(100); + return regmap_read_poll_timeout(priv->map, RTL8365MB_CHIP_RESET_REG, val, + !(val & RTL8365MB_CHIP_RESET_HW_MASK), + 20000, 1e6); +} + +static int rtl8365mb_setup(struct dsa_switch *ds) +{ + struct realtek_priv *priv = ds->priv; + struct rtl8365mb_cpu *cpu; + struct dsa_port *cpu_dp; + struct rtl8365mb *mb; + int ret; + int i; + + mb = priv->chip_data; + cpu = &mb->cpu; + + ret = rtl8365mb_reset_chip(priv); + if (ret) { + dev_err(priv->dev, "failed to reset chip: %d\n", ret); + goto out_error; + } + + /* Configure switch to vendor-defined initial state */ + ret = rtl8365mb_switch_init(priv); + if (ret) { + dev_err(priv->dev, "failed to initialize switch: %d\n", ret); + goto out_error; + } + + /* Set up cascading IRQs */ + ret = rtl8365mb_irq_setup(priv); + if (ret == -EPROBE_DEFER) + return ret; + else if (ret) + dev_info(priv->dev, "no interrupt support\n"); + + /* Configure CPU tagging */ + dsa_switch_for_each_cpu_port(cpu_dp, priv->ds) { + cpu->mask |= BIT(cpu_dp->index); + + if (cpu->trap_port == RTL8365MB_MAX_NUM_PORTS) + cpu->trap_port = cpu_dp->index; + } + cpu->enable = cpu->mask > 0; + ret = rtl8365mb_cpu_config(priv); + if (ret) + goto out_teardown_irq; + + /* Configure ports */ + for (i = 0; i < priv->num_ports; i++) { + struct rtl8365mb_port *p = &mb->ports[i]; + + if (dsa_is_unused_port(priv->ds, i)) + continue; + + /* Forward only to the CPU */ + ret = rtl8365mb_port_set_isolation(priv, i, cpu->mask); + if (ret) + goto out_teardown_irq; + + /* Disable learning */ + ret = rtl8365mb_port_set_learning(priv, i, false); + if (ret) + goto out_teardown_irq; + + /* Set the initial STP state of all ports to DISABLED, otherwise + * ports will still forward frames to the CPU despite being + * administratively down by default. + */ + rtl8365mb_port_stp_state_set(priv->ds, i, BR_STATE_DISABLED); + + /* Set up per-port private data */ + p->priv = priv; + p->index = i; + } + + /* Set maximum packet length to 1536 bytes */ + ret = regmap_update_bits(priv->map, RTL8365MB_CFG0_MAX_LEN_REG, + RTL8365MB_CFG0_MAX_LEN_MASK, + FIELD_PREP(RTL8365MB_CFG0_MAX_LEN_MASK, 1536)); + if (ret) + goto out_teardown_irq; + + if (priv->setup_interface) { + ret = priv->setup_interface(ds); + if (ret) { + dev_err(priv->dev, "could not set up MDIO bus\n"); + goto out_teardown_irq; + } + } + + /* Start statistics counter polling */ + rtl8365mb_stats_setup(priv); + + return 0; + +out_teardown_irq: + rtl8365mb_irq_teardown(priv); + +out_error: + return ret; +} + +static void rtl8365mb_teardown(struct dsa_switch *ds) +{ + struct realtek_priv *priv = ds->priv; + + rtl8365mb_stats_teardown(priv); + rtl8365mb_irq_teardown(priv); +} + +static int rtl8365mb_get_chip_id_and_ver(struct regmap *map, u32 *id, u32 *ver) +{ + int ret; + + /* For some reason we have to write a magic value to an arbitrary + * register whenever accessing the chip ID/version registers. + */ + ret = regmap_write(map, RTL8365MB_MAGIC_REG, RTL8365MB_MAGIC_VALUE); + if (ret) + return ret; + + ret = regmap_read(map, RTL8365MB_CHIP_ID_REG, id); + if (ret) + return ret; + + ret = regmap_read(map, RTL8365MB_CHIP_VER_REG, ver); + if (ret) + return ret; + + /* Reset magic register */ + ret = regmap_write(map, RTL8365MB_MAGIC_REG, 0); + if (ret) + return ret; + + return 0; +} + +static int rtl8365mb_detect(struct realtek_priv *priv) +{ + struct rtl8365mb *mb = priv->chip_data; + u32 chip_id; + u32 chip_ver; + int ret; + + ret = rtl8365mb_get_chip_id_and_ver(priv->map, &chip_id, &chip_ver); + if (ret) { + dev_err(priv->dev, "failed to read chip id and version: %d\n", + ret); + return ret; + } + + switch (chip_id) { + case RTL8365MB_CHIP_ID_8365MB_VC: + switch (chip_ver) { + case RTL8365MB_CHIP_VER_8365MB_VC: + dev_info(priv->dev, + "found an RTL8365MB-VC switch (ver=0x%04x)\n", + chip_ver); + break; + case RTL8365MB_CHIP_VER_8367RB: + dev_info(priv->dev, + "found an RTL8367RB-VB switch (ver=0x%04x)\n", + chip_ver); + break; + case RTL8365MB_CHIP_VER_8367S: + dev_info(priv->dev, + "found an RTL8367S switch (ver=0x%04x)\n", + chip_ver); + break; + default: + dev_err(priv->dev, "unrecognized switch version (ver=0x%04x)", + chip_ver); + return -ENODEV; + } + + priv->num_ports = RTL8365MB_MAX_NUM_PORTS; + + mb->priv = priv; + mb->chip_id = chip_id; + mb->chip_ver = chip_ver; + mb->port_mask = GENMASK(priv->num_ports - 1, 0); + mb->learn_limit_max = RTL8365MB_LEARN_LIMIT_MAX; + mb->jam_table = rtl8365mb_init_jam_8365mb_vc; + mb->jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc); + + mb->cpu.trap_port = RTL8365MB_MAX_NUM_PORTS; + mb->cpu.insert = RTL8365MB_CPU_INSERT_TO_ALL; + mb->cpu.position = RTL8365MB_CPU_POS_AFTER_SA; + mb->cpu.rx_length = RTL8365MB_CPU_RXLEN_64BYTES; + mb->cpu.format = RTL8365MB_CPU_FORMAT_8BYTES; + + break; + default: + dev_err(priv->dev, + "found an unknown Realtek switch (id=0x%04x, ver=0x%04x)\n", + chip_id, chip_ver); + return -ENODEV; + } + + return 0; +} + +static const struct dsa_switch_ops rtl8365mb_switch_ops_smi = { + .get_tag_protocol = rtl8365mb_get_tag_protocol, + .change_tag_protocol = rtl8365mb_change_tag_protocol, + .setup = rtl8365mb_setup, + .teardown = rtl8365mb_teardown, + .phylink_get_caps = rtl8365mb_phylink_get_caps, + .phylink_mac_config = rtl8365mb_phylink_mac_config, + .phylink_mac_link_down = rtl8365mb_phylink_mac_link_down, + .phylink_mac_link_up = rtl8365mb_phylink_mac_link_up, + .port_stp_state_set = rtl8365mb_port_stp_state_set, + .get_strings = rtl8365mb_get_strings, + .get_ethtool_stats = rtl8365mb_get_ethtool_stats, + .get_sset_count = rtl8365mb_get_sset_count, + .get_eth_phy_stats = rtl8365mb_get_phy_stats, + .get_eth_mac_stats = rtl8365mb_get_mac_stats, + .get_eth_ctrl_stats = rtl8365mb_get_ctrl_stats, + .get_stats64 = rtl8365mb_get_stats64, +}; + +static const struct dsa_switch_ops rtl8365mb_switch_ops_mdio = { + .get_tag_protocol = rtl8365mb_get_tag_protocol, + .change_tag_protocol = rtl8365mb_change_tag_protocol, + .setup = rtl8365mb_setup, + .teardown = rtl8365mb_teardown, + .phylink_get_caps = rtl8365mb_phylink_get_caps, + .phylink_mac_config = rtl8365mb_phylink_mac_config, + .phylink_mac_link_down = rtl8365mb_phylink_mac_link_down, + .phylink_mac_link_up = rtl8365mb_phylink_mac_link_up, + .phy_read = rtl8365mb_dsa_phy_read, + .phy_write = rtl8365mb_dsa_phy_write, + .port_stp_state_set = rtl8365mb_port_stp_state_set, + .get_strings = rtl8365mb_get_strings, + .get_ethtool_stats = rtl8365mb_get_ethtool_stats, + .get_sset_count = rtl8365mb_get_sset_count, + .get_eth_phy_stats = rtl8365mb_get_phy_stats, + .get_eth_mac_stats = rtl8365mb_get_mac_stats, + .get_eth_ctrl_stats = rtl8365mb_get_ctrl_stats, + .get_stats64 = rtl8365mb_get_stats64, +}; + +static const struct realtek_ops rtl8365mb_ops = { + .detect = rtl8365mb_detect, + .phy_read = rtl8365mb_phy_read, + .phy_write = rtl8365mb_phy_write, +}; + +const struct realtek_variant rtl8365mb_variant = { + .ds_ops_smi = &rtl8365mb_switch_ops_smi, + .ds_ops_mdio = &rtl8365mb_switch_ops_mdio, + .ops = &rtl8365mb_ops, + .clk_delay = 10, + .cmd_read = 0xb9, + .cmd_write = 0xb8, + .chip_data_sz = sizeof(struct rtl8365mb), +}; +EXPORT_SYMBOL_GPL(rtl8365mb_variant); + +MODULE_AUTHOR("Alvin Šipraga <alsi@bang-olufsen.dk>"); +MODULE_DESCRIPTION("Driver for RTL8365MB-VC ethernet switch"); +MODULE_LICENSE("GPL"); |