diff options
Diffstat (limited to 'drivers/net/ethernet/intel/ice/ice_ptp_hw.c')
| -rw-r--r-- | drivers/net/ethernet/intel/ice/ice_ptp_hw.c | 2913 |
1 files changed, 2755 insertions, 158 deletions
diff --git a/drivers/net/ethernet/intel/ice/ice_ptp_hw.c b/drivers/net/ethernet/intel/ice/ice_ptp_hw.c index 29f947c0cd2e..772b1f566d6e 100644 --- a/drivers/net/ethernet/intel/ice/ice_ptp_hw.c +++ b/drivers/net/ethernet/intel/ice/ice_ptp_hw.c @@ -1,8 +1,11 @@ // SPDX-License-Identifier: GPL-2.0 /* Copyright (C) 2021, Intel Corporation. */ +#include <linux/delay.h> #include "ice_common.h" #include "ice_ptp_hw.h" +#include "ice_ptp_consts.h" +#include "ice_cgu_regs.h" /* Low level functions for interacting with and managing the device clock used * for the Precision Time Protocol. @@ -29,6 +32,15 @@ * * For E810 devices, the increment frequency is 812.5 MHz * + * For E822 devices the clock can be derived from different sources, and the + * increment has an effective frequency of one of the following: + * - 823.4375 MHz + * - 783.36 MHz + * - 796.875 MHz + * - 816 MHz + * - 830.078125 MHz + * - 783.36 MHz + * * The hardware captures timestamps in the PHY for incoming packets, and for * outgoing packets on request. To support this, the PHY maintains a timer * that matches the lower 64 bits of the global source timer. @@ -37,6 +49,24 @@ * shadow registers are used to prepare the desired initial values. A special * sync command is issued to trigger copying from the shadow registers into * the appropriate source and PHY registers simultaneously. + * + * The driver supports devices which have different PHYs with subtly different + * mechanisms to program and control the timers. We divide the devices into + * families named after the first major device, E810 and similar devices, and + * E822 and similar devices. + * + * - E822 based devices have additional support for fine grained Vernier + * calibration which requires significant setup + * - The layout of timestamp data in the PHY register blocks is different + * - The way timer synchronization commands are issued is different. + * + * To support this, very low level functions have an e810 or e822 suffix + * indicating what type of device they work on. Higher level abstractions for + * tasks that can be done on both devices do not have the suffix and will + * correctly look up the appropriate low level function when running. + * + * Functions which only make sense on a single device family may not have + * a suitable generic implementation */ /** @@ -51,6 +81,2447 @@ u8 ice_get_ptp_src_clock_index(struct ice_hw *hw) return hw->func_caps.ts_func_info.tmr_index_assoc; } +/** + * ice_ptp_read_src_incval - Read source timer increment value + * @hw: pointer to HW struct + * + * Read the increment value of the source timer and return it. + */ +static u64 ice_ptp_read_src_incval(struct ice_hw *hw) +{ + u32 lo, hi; + u8 tmr_idx; + + tmr_idx = ice_get_ptp_src_clock_index(hw); + + lo = rd32(hw, GLTSYN_INCVAL_L(tmr_idx)); + hi = rd32(hw, GLTSYN_INCVAL_H(tmr_idx)); + + return ((u64)(hi & INCVAL_HIGH_M) << 32) | lo; +} + +/** + * ice_ptp_src_cmd - Prepare source timer for a timer command + * @hw: pointer to HW structure + * @cmd: Timer command + * + * Prepare the source timer for an upcoming timer sync command. + */ +static void ice_ptp_src_cmd(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) +{ + u32 cmd_val; + u8 tmr_idx; + + tmr_idx = ice_get_ptp_src_clock_index(hw); + cmd_val = tmr_idx << SEL_CPK_SRC; + + switch (cmd) { + case INIT_TIME: + cmd_val |= GLTSYN_CMD_INIT_TIME; + break; + case INIT_INCVAL: + cmd_val |= GLTSYN_CMD_INIT_INCVAL; + break; + case ADJ_TIME: + cmd_val |= GLTSYN_CMD_ADJ_TIME; + break; + case ADJ_TIME_AT_TIME: + cmd_val |= GLTSYN_CMD_ADJ_INIT_TIME; + break; + case READ_TIME: + cmd_val |= GLTSYN_CMD_READ_TIME; + break; + } + + wr32(hw, GLTSYN_CMD, cmd_val); +} + +/** + * ice_ptp_exec_tmr_cmd - Execute all prepared timer commands + * @hw: pointer to HW struct + * + * Write the SYNC_EXEC_CMD bit to the GLTSYN_CMD_SYNC register, and flush the + * write immediately. This triggers the hardware to begin executing all of the + * source and PHY timer commands synchronously. + */ +static void ice_ptp_exec_tmr_cmd(struct ice_hw *hw) +{ + wr32(hw, GLTSYN_CMD_SYNC, SYNC_EXEC_CMD); + ice_flush(hw); +} + +/* E822 family functions + * + * The following functions operate on the E822 family of devices. + */ + +/** + * ice_fill_phy_msg_e822 - Fill message data for a PHY register access + * @msg: the PHY message buffer to fill in + * @port: the port to access + * @offset: the register offset + */ +static void +ice_fill_phy_msg_e822(struct ice_sbq_msg_input *msg, u8 port, u16 offset) +{ + int phy_port, phy, quadtype; + + phy_port = port % ICE_PORTS_PER_PHY; + phy = port / ICE_PORTS_PER_PHY; + quadtype = (port / ICE_PORTS_PER_QUAD) % ICE_NUM_QUAD_TYPE; + + if (quadtype == 0) { + msg->msg_addr_low = P_Q0_L(P_0_BASE + offset, phy_port); + msg->msg_addr_high = P_Q0_H(P_0_BASE + offset, phy_port); + } else { + msg->msg_addr_low = P_Q1_L(P_4_BASE + offset, phy_port); + msg->msg_addr_high = P_Q1_H(P_4_BASE + offset, phy_port); + } + + if (phy == 0) + msg->dest_dev = rmn_0; + else if (phy == 1) + msg->dest_dev = rmn_1; + else + msg->dest_dev = rmn_2; +} + +/** + * ice_is_64b_phy_reg_e822 - Check if this is a 64bit PHY register + * @low_addr: the low address to check + * @high_addr: on return, contains the high address of the 64bit register + * + * Checks if the provided low address is one of the known 64bit PHY values + * represented as two 32bit registers. If it is, return the appropriate high + * register offset to use. + */ +static bool ice_is_64b_phy_reg_e822(u16 low_addr, u16 *high_addr) +{ + switch (low_addr) { + case P_REG_PAR_PCS_TX_OFFSET_L: + *high_addr = P_REG_PAR_PCS_TX_OFFSET_U; + return true; + case P_REG_PAR_PCS_RX_OFFSET_L: + *high_addr = P_REG_PAR_PCS_RX_OFFSET_U; + return true; + case P_REG_PAR_TX_TIME_L: + *high_addr = P_REG_PAR_TX_TIME_U; + return true; + case P_REG_PAR_RX_TIME_L: + *high_addr = P_REG_PAR_RX_TIME_U; + return true; + case P_REG_TOTAL_TX_OFFSET_L: + *high_addr = P_REG_TOTAL_TX_OFFSET_U; + return true; + case P_REG_TOTAL_RX_OFFSET_L: + *high_addr = P_REG_TOTAL_RX_OFFSET_U; + return true; + case P_REG_UIX66_10G_40G_L: + *high_addr = P_REG_UIX66_10G_40G_U; + return true; + case P_REG_UIX66_25G_100G_L: + *high_addr = P_REG_UIX66_25G_100G_U; + return true; + case P_REG_TX_CAPTURE_L: + *high_addr = P_REG_TX_CAPTURE_U; + return true; + case P_REG_RX_CAPTURE_L: + *high_addr = P_REG_RX_CAPTURE_U; + return true; + case P_REG_TX_TIMER_INC_PRE_L: + *high_addr = P_REG_TX_TIMER_INC_PRE_U; + return true; + case P_REG_RX_TIMER_INC_PRE_L: + *high_addr = P_REG_RX_TIMER_INC_PRE_U; + return true; + default: + return false; + } +} + +/** + * ice_is_40b_phy_reg_e822 - Check if this is a 40bit PHY register + * @low_addr: the low address to check + * @high_addr: on return, contains the high address of the 40bit value + * + * Checks if the provided low address is one of the known 40bit PHY values + * split into two registers with the lower 8 bits in the low register and the + * upper 32 bits in the high register. If it is, return the appropriate high + * register offset to use. + */ +static bool ice_is_40b_phy_reg_e822(u16 low_addr, u16 *high_addr) +{ + switch (low_addr) { + case P_REG_TIMETUS_L: + *high_addr = P_REG_TIMETUS_U; + return true; + case P_REG_PAR_RX_TUS_L: + *high_addr = P_REG_PAR_RX_TUS_U; + return true; + case P_REG_PAR_TX_TUS_L: + *high_addr = P_REG_PAR_TX_TUS_U; + return true; + case P_REG_PCS_RX_TUS_L: + *high_addr = P_REG_PCS_RX_TUS_U; + return true; + case P_REG_PCS_TX_TUS_L: + *high_addr = P_REG_PCS_TX_TUS_U; + return true; + case P_REG_DESK_PAR_RX_TUS_L: + *high_addr = P_REG_DESK_PAR_RX_TUS_U; + return true; + case P_REG_DESK_PAR_TX_TUS_L: + *high_addr = P_REG_DESK_PAR_TX_TUS_U; + return true; + case P_REG_DESK_PCS_RX_TUS_L: + *high_addr = P_REG_DESK_PCS_RX_TUS_U; + return true; + case P_REG_DESK_PCS_TX_TUS_L: + *high_addr = P_REG_DESK_PCS_TX_TUS_U; + return true; + default: + return false; + } +} + +/** + * ice_read_phy_reg_e822 - Read a PHY register + * @hw: pointer to the HW struct + * @port: PHY port to read from + * @offset: PHY register offset to read + * @val: on return, the contents read from the PHY + * + * Read a PHY register for the given port over the device sideband queue. + */ +int +ice_read_phy_reg_e822(struct ice_hw *hw, u8 port, u16 offset, u32 *val) +{ + struct ice_sbq_msg_input msg = {0}; + int err; + + ice_fill_phy_msg_e822(&msg, port, offset); + msg.opcode = ice_sbq_msg_rd; + + err = ice_sbq_rw_reg(hw, &msg); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to send message to PHY, err %d\n", + err); + return err; + } + + *val = msg.data; + + return 0; +} + +/** + * ice_read_64b_phy_reg_e822 - Read a 64bit value from PHY registers + * @hw: pointer to the HW struct + * @port: PHY port to read from + * @low_addr: offset of the lower register to read from + * @val: on return, the contents of the 64bit value from the PHY registers + * + * Reads the two registers associated with a 64bit value and returns it in the + * val pointer. The offset always specifies the lower register offset to use. + * The high offset is looked up. This function only operates on registers + * known to be two parts of a 64bit value. + */ +static int +ice_read_64b_phy_reg_e822(struct ice_hw *hw, u8 port, u16 low_addr, u64 *val) +{ + u32 low, high; + u16 high_addr; + int err; + + /* Only operate on registers known to be split into two 32bit + * registers. + */ + if (!ice_is_64b_phy_reg_e822(low_addr, &high_addr)) { + ice_debug(hw, ICE_DBG_PTP, "Invalid 64b register addr 0x%08x\n", + low_addr); + return -EINVAL; + } + + err = ice_read_phy_reg_e822(hw, port, low_addr, &low); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read from low register 0x%08x\n, err %d", + low_addr, err); + return err; + } + + err = ice_read_phy_reg_e822(hw, port, high_addr, &high); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read from high register 0x%08x\n, err %d", + high_addr, err); + return err; + } + + *val = (u64)high << 32 | low; + + return 0; +} + +/** + * ice_write_phy_reg_e822 - Write a PHY register + * @hw: pointer to the HW struct + * @port: PHY port to write to + * @offset: PHY register offset to write + * @val: The value to write to the register + * + * Write a PHY register for the given port over the device sideband queue. + */ +int +ice_write_phy_reg_e822(struct ice_hw *hw, u8 port, u16 offset, u32 val) +{ + struct ice_sbq_msg_input msg = {0}; + int err; + + ice_fill_phy_msg_e822(&msg, port, offset); + msg.opcode = ice_sbq_msg_wr; + msg.data = val; + + err = ice_sbq_rw_reg(hw, &msg); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to send message to PHY, err %d\n", + err); + return err; + } + + return 0; +} + +/** + * ice_write_40b_phy_reg_e822 - Write a 40b value to the PHY + * @hw: pointer to the HW struct + * @port: port to write to + * @low_addr: offset of the low register + * @val: 40b value to write + * + * Write the provided 40b value to the two associated registers by splitting + * it up into two chunks, the lower 8 bits and the upper 32 bits. + */ +static int +ice_write_40b_phy_reg_e822(struct ice_hw *hw, u8 port, u16 low_addr, u64 val) +{ + u32 low, high; + u16 high_addr; + int err; + + /* Only operate on registers known to be split into a lower 8 bit + * register and an upper 32 bit register. + */ + if (!ice_is_40b_phy_reg_e822(low_addr, &high_addr)) { + ice_debug(hw, ICE_DBG_PTP, "Invalid 40b register addr 0x%08x\n", + low_addr); + return -EINVAL; + } + + low = (u32)(val & P_REG_40B_LOW_M); + high = (u32)(val >> P_REG_40B_HIGH_S); + + err = ice_write_phy_reg_e822(hw, port, low_addr, low); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write to low register 0x%08x\n, err %d", + low_addr, err); + return err; + } + + err = ice_write_phy_reg_e822(hw, port, high_addr, high); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write to high register 0x%08x\n, err %d", + high_addr, err); + return err; + } + + return 0; +} + +/** + * ice_write_64b_phy_reg_e822 - Write a 64bit value to PHY registers + * @hw: pointer to the HW struct + * @port: PHY port to read from + * @low_addr: offset of the lower register to read from + * @val: the contents of the 64bit value to write to PHY + * + * Write the 64bit value to the two associated 32bit PHY registers. The offset + * is always specified as the lower register, and the high address is looked + * up. This function only operates on registers known to be two parts of + * a 64bit value. + */ +static int +ice_write_64b_phy_reg_e822(struct ice_hw *hw, u8 port, u16 low_addr, u64 val) +{ + u32 low, high; + u16 high_addr; + int err; + + /* Only operate on registers known to be split into two 32bit + * registers. + */ + if (!ice_is_64b_phy_reg_e822(low_addr, &high_addr)) { + ice_debug(hw, ICE_DBG_PTP, "Invalid 64b register addr 0x%08x\n", + low_addr); + return -EINVAL; + } + + low = lower_32_bits(val); + high = upper_32_bits(val); + + err = ice_write_phy_reg_e822(hw, port, low_addr, low); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write to low register 0x%08x\n, err %d", + low_addr, err); + return err; + } + + err = ice_write_phy_reg_e822(hw, port, high_addr, high); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write to high register 0x%08x\n, err %d", + high_addr, err); + return err; + } + + return 0; +} + +/** + * ice_fill_quad_msg_e822 - Fill message data for quad register access + * @msg: the PHY message buffer to fill in + * @quad: the quad to access + * @offset: the register offset + * + * Fill a message buffer for accessing a register in a quad shared between + * multiple PHYs. + */ +static void +ice_fill_quad_msg_e822(struct ice_sbq_msg_input *msg, u8 quad, u16 offset) +{ + u32 addr; + + msg->dest_dev = rmn_0; + + if ((quad % ICE_NUM_QUAD_TYPE) == 0) + addr = Q_0_BASE + offset; + else + addr = Q_1_BASE + offset; + + msg->msg_addr_low = lower_16_bits(addr); + msg->msg_addr_high = upper_16_bits(addr); +} + +/** + * ice_read_quad_reg_e822 - Read a PHY quad register + * @hw: pointer to the HW struct + * @quad: quad to read from + * @offset: quad register offset to read + * @val: on return, the contents read from the quad + * + * Read a quad register over the device sideband queue. Quad registers are + * shared between multiple PHYs. + */ +int +ice_read_quad_reg_e822(struct ice_hw *hw, u8 quad, u16 offset, u32 *val) +{ + struct ice_sbq_msg_input msg = {0}; + int err; + + if (quad >= ICE_MAX_QUAD) + return -EINVAL; + + ice_fill_quad_msg_e822(&msg, quad, offset); + msg.opcode = ice_sbq_msg_rd; + + err = ice_sbq_rw_reg(hw, &msg); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to send message to PHY, err %d\n", + err); + return err; + } + + *val = msg.data; + + return 0; +} + +/** + * ice_write_quad_reg_e822 - Write a PHY quad register + * @hw: pointer to the HW struct + * @quad: quad to write to + * @offset: quad register offset to write + * @val: The value to write to the register + * + * Write a quad register over the device sideband queue. Quad registers are + * shared between multiple PHYs. + */ +int +ice_write_quad_reg_e822(struct ice_hw *hw, u8 quad, u16 offset, u32 val) +{ + struct ice_sbq_msg_input msg = {0}; + int err; + + if (quad >= ICE_MAX_QUAD) + return -EINVAL; + + ice_fill_quad_msg_e822(&msg, quad, offset); + msg.opcode = ice_sbq_msg_wr; + msg.data = val; + + err = ice_sbq_rw_reg(hw, &msg); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to send message to PHY, err %d\n", + err); + return err; + } + + return 0; +} + +/** + * ice_read_phy_tstamp_e822 - Read a PHY timestamp out of the quad block + * @hw: pointer to the HW struct + * @quad: the quad to read from + * @idx: the timestamp index to read + * @tstamp: on return, the 40bit timestamp value + * + * Read a 40bit timestamp value out of the two associated registers in the + * quad memory block that is shared between the internal PHYs of the E822 + * family of devices. + */ +static int +ice_read_phy_tstamp_e822(struct ice_hw *hw, u8 quad, u8 idx, u64 *tstamp) +{ + u16 lo_addr, hi_addr; + u32 lo, hi; + int err; + + lo_addr = (u16)TS_L(Q_REG_TX_MEMORY_BANK_START, idx); + hi_addr = (u16)TS_H(Q_REG_TX_MEMORY_BANK_START, idx); + + err = ice_read_quad_reg_e822(hw, quad, lo_addr, &lo); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read low PTP timestamp register, err %d\n", + err); + return err; + } + + err = ice_read_quad_reg_e822(hw, quad, hi_addr, &hi); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read high PTP timestamp register, err %d\n", + err); + return err; + } + + /* For E822 based internal PHYs, the timestamp is reported with the + * lower 8 bits in the low register, and the upper 32 bits in the high + * register. + */ + *tstamp = ((u64)hi) << TS_PHY_HIGH_S | ((u64)lo & TS_PHY_LOW_M); + + return 0; +} + +/** + * ice_clear_phy_tstamp_e822 - Clear a timestamp from the quad block + * @hw: pointer to the HW struct + * @quad: the quad to read from + * @idx: the timestamp index to reset + * + * Clear a timestamp, resetting its valid bit, from the PHY quad block that is + * shared between the internal PHYs on the E822 devices. + */ +static int +ice_clear_phy_tstamp_e822(struct ice_hw *hw, u8 quad, u8 idx) +{ + u16 lo_addr, hi_addr; + int err; + + lo_addr = (u16)TS_L(Q_REG_TX_MEMORY_BANK_START, idx); + hi_addr = (u16)TS_H(Q_REG_TX_MEMORY_BANK_START, idx); + + err = ice_write_quad_reg_e822(hw, quad, lo_addr, 0); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to clear low PTP timestamp register, err %d\n", + err); + return err; + } + + err = ice_write_quad_reg_e822(hw, quad, hi_addr, 0); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to clear high PTP timestamp register, err %d\n", + err); + return err; + } + + return 0; +} + +/** + * ice_read_cgu_reg_e822 - Read a CGU register + * @hw: pointer to the HW struct + * @addr: Register address to read + * @val: storage for register value read + * + * Read the contents of a register of the Clock Generation Unit. Only + * applicable to E822 devices. + */ +static int +ice_read_cgu_reg_e822(struct ice_hw *hw, u32 addr, u32 *val) +{ + struct ice_sbq_msg_input cgu_msg; + int err; + + cgu_msg.opcode = ice_sbq_msg_rd; + cgu_msg.dest_dev = cgu; + cgu_msg.msg_addr_low = addr; + cgu_msg.msg_addr_high = 0x0; + + err = ice_sbq_rw_reg(hw, &cgu_msg); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read CGU register 0x%04x, err %d\n", + addr, err); + return err; + } + + *val = cgu_msg.data; + + return err; +} + +/** + * ice_write_cgu_reg_e822 - Write a CGU register + * @hw: pointer to the HW struct + * @addr: Register address to write + * @val: value to write into the register + * + * Write the specified value to a register of the Clock Generation Unit. Only + * applicable to E822 devices. + */ +static int +ice_write_cgu_reg_e822(struct ice_hw *hw, u32 addr, u32 val) +{ + struct ice_sbq_msg_input cgu_msg; + int err; + + cgu_msg.opcode = ice_sbq_msg_wr; + cgu_msg.dest_dev = cgu; + cgu_msg.msg_addr_low = addr; + cgu_msg.msg_addr_high = 0x0; + cgu_msg.data = val; + + err = ice_sbq_rw_reg(hw, &cgu_msg); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write CGU register 0x%04x, err %d\n", + addr, err); + return err; + } + + return err; +} + +/** + * ice_clk_freq_str - Convert time_ref_freq to string + * @clk_freq: Clock frequency + * + * Convert the specified TIME_REF clock frequency to a string. + */ +static const char *ice_clk_freq_str(u8 clk_freq) +{ + switch ((enum ice_time_ref_freq)clk_freq) { + case ICE_TIME_REF_FREQ_25_000: + return "25 MHz"; + case ICE_TIME_REF_FREQ_122_880: + return "122.88 MHz"; + case ICE_TIME_REF_FREQ_125_000: + return "125 MHz"; + case ICE_TIME_REF_FREQ_153_600: + return "153.6 MHz"; + case ICE_TIME_REF_FREQ_156_250: + return "156.25 MHz"; + case ICE_TIME_REF_FREQ_245_760: + return "245.76 MHz"; + default: + return "Unknown"; + } +} + +/** + * ice_clk_src_str - Convert time_ref_src to string + * @clk_src: Clock source + * + * Convert the specified clock source to its string name. + */ +static const char *ice_clk_src_str(u8 clk_src) +{ + switch ((enum ice_clk_src)clk_src) { + case ICE_CLK_SRC_TCX0: + return "TCX0"; + case ICE_CLK_SRC_TIME_REF: + return "TIME_REF"; + default: + return "Unknown"; + } +} + +/** + * ice_cfg_cgu_pll_e822 - Configure the Clock Generation Unit + * @hw: pointer to the HW struct + * @clk_freq: Clock frequency to program + * @clk_src: Clock source to select (TIME_REF, or TCX0) + * + * Configure the Clock Generation Unit with the desired clock frequency and + * time reference, enabling the PLL which drives the PTP hardware clock. + */ +static int +ice_cfg_cgu_pll_e822(struct ice_hw *hw, enum ice_time_ref_freq clk_freq, + enum ice_clk_src clk_src) +{ + union tspll_ro_bwm_lf bwm_lf; + union nac_cgu_dword19 dw19; + union nac_cgu_dword22 dw22; + union nac_cgu_dword24 dw24; + union nac_cgu_dword9 dw9; + int err; + + if (clk_freq >= NUM_ICE_TIME_REF_FREQ) { + dev_warn(ice_hw_to_dev(hw), "Invalid TIME_REF frequency %u\n", + clk_freq); + return -EINVAL; + } + + if (clk_src >= NUM_ICE_CLK_SRC) { + dev_warn(ice_hw_to_dev(hw), "Invalid clock source %u\n", + clk_src); + return -EINVAL; + } + + if (clk_src == ICE_CLK_SRC_TCX0 && + clk_freq != ICE_TIME_REF_FREQ_25_000) { + dev_warn(ice_hw_to_dev(hw), + "TCX0 only supports 25 MHz frequency\n"); + return -EINVAL; + } + + err = ice_read_cgu_reg_e822(hw, NAC_CGU_DWORD9, &dw9.val); + if (err) + return err; + + err = ice_read_cgu_reg_e822(hw, NAC_CGU_DWORD24, &dw24.val); + if (err) + return err; + + err = ice_read_cgu_reg_e822(hw, TSPLL_RO_BWM_LF, &bwm_lf.val); + if (err) + return err; + + /* Log the current clock configuration */ + ice_debug(hw, ICE_DBG_PTP, "Current CGU configuration -- %s, clk_src %s, clk_freq %s, PLL %s\n", + dw24.field.ts_pll_enable ? "enabled" : "disabled", + ice_clk_src_str(dw24.field.time_ref_sel), + ice_clk_freq_str(dw9.field.time_ref_freq_sel), + bwm_lf.field.plllock_true_lock_cri ? "locked" : "unlocked"); + + /* Disable the PLL before changing the clock source or frequency */ + if (dw24.field.ts_pll_enable) { + dw24.field.ts_pll_enable = 0; + + err = ice_write_cgu_reg_e822(hw, NAC_CGU_DWORD24, dw24.val); + if (err) + return err; + } + + /* Set the frequency */ + dw9.field.time_ref_freq_sel = clk_freq; + err = ice_write_cgu_reg_e822(hw, NAC_CGU_DWORD9, dw9.val); + if (err) + return err; + + /* Configure the TS PLL feedback divisor */ + err = ice_read_cgu_reg_e822(hw, NAC_CGU_DWORD19, &dw19.val); + if (err) + return err; + + dw19.field.tspll_fbdiv_intgr = e822_cgu_params[clk_freq].feedback_div; + dw19.field.tspll_ndivratio = 1; + + err = ice_write_cgu_reg_e822(hw, NAC_CGU_DWORD19, dw19.val); + if (err) + return err; + + /* Configure the TS PLL post divisor */ + err = ice_read_cgu_reg_e822(hw, NAC_CGU_DWORD22, &dw22.val); + if (err) + return err; + + dw22.field.time1588clk_div = e822_cgu_params[clk_freq].post_pll_div; + dw22.field.time1588clk_sel_div2 = 0; + + err = ice_write_cgu_reg_e822(hw, NAC_CGU_DWORD22, dw22.val); + if (err) + return err; + + /* Configure the TS PLL pre divisor and clock source */ + err = ice_read_cgu_reg_e822(hw, NAC_CGU_DWORD24, &dw24.val); + if (err) + return err; + + dw24.field.ref1588_ck_div = e822_cgu_params[clk_freq].refclk_pre_div; + dw24.field.tspll_fbdiv_frac = e822_cgu_params[clk_freq].frac_n_div; + dw24.field.time_ref_sel = clk_src; + + err = ice_write_cgu_reg_e822(hw, NAC_CGU_DWORD24, dw24.val); + if (err) + return err; + + /* Finally, enable the PLL */ + dw24.field.ts_pll_enable = 1; + + err = ice_write_cgu_reg_e822(hw, NAC_CGU_DWORD24, dw24.val); + if (err) + return err; + + /* Wait to verify if the PLL locks */ + usleep_range(1000, 5000); + + err = ice_read_cgu_reg_e822(hw, TSPLL_RO_BWM_LF, &bwm_lf.val); + if (err) + return err; + + if (!bwm_lf.field.plllock_true_lock_cri) { + dev_warn(ice_hw_to_dev(hw), "CGU PLL failed to lock\n"); + return -EBUSY; + } + + /* Log the current clock configuration */ + ice_debug(hw, ICE_DBG_PTP, "New CGU configuration -- %s, clk_src %s, clk_freq %s, PLL %s\n", + dw24.field.ts_pll_enable ? "enabled" : "disabled", + ice_clk_src_str(dw24.field.time_ref_sel), + ice_clk_freq_str(dw9.field.time_ref_freq_sel), + bwm_lf.field.plllock_true_lock_cri ? "locked" : "unlocked"); + + return 0; +} + +/** + * ice_init_cgu_e822 - Initialize CGU with settings from firmware + * @hw: pointer to the HW structure + * + * Initialize the Clock Generation Unit of the E822 device. + */ +static int ice_init_cgu_e822(struct ice_hw *hw) +{ + struct ice_ts_func_info *ts_info = &hw->func_caps.ts_func_info; + union tspll_cntr_bist_settings cntr_bist; + int err; + + err = ice_read_cgu_reg_e822(hw, TSPLL_CNTR_BIST_SETTINGS, + &cntr_bist.val); + if (err) + return err; + + /* Disable sticky lock detection so lock err reported is accurate */ + cntr_bist.field.i_plllock_sel_0 = 0; + cntr_bist.field.i_plllock_sel_1 = 0; + + err = ice_write_cgu_reg_e822(hw, TSPLL_CNTR_BIST_SETTINGS, + cntr_bist.val); + if (err) + return err; + + /* Configure the CGU PLL using the parameters from the function + * capabilities. + */ + err = ice_cfg_cgu_pll_e822(hw, ts_info->time_ref, + (enum ice_clk_src)ts_info->clk_src); + if (err) + return err; + + return 0; +} + +/** + * ice_ptp_set_vernier_wl - Set the window length for vernier calibration + * @hw: pointer to the HW struct + * + * Set the window length used for the vernier port calibration process. + */ +static int ice_ptp_set_vernier_wl(struct ice_hw *hw) +{ + u8 port; + + for (port = 0; port < ICE_NUM_EXTERNAL_PORTS; port++) { + int err; + + err = ice_write_phy_reg_e822(hw, port, P_REG_WL, + PTP_VERNIER_WL); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to set vernier window length for port %u, err %d\n", + port, err); + return err; + } + } + + return 0; +} + +/** + * ice_ptp_init_phc_e822 - Perform E822 specific PHC initialization + * @hw: pointer to HW struct + * + * Perform PHC initialization steps specific to E822 devices. + */ +static int ice_ptp_init_phc_e822(struct ice_hw *hw) +{ + int err; + u32 regval; + + /* Enable reading switch and PHY registers over the sideband queue */ +#define PF_SB_REM_DEV_CTL_SWITCH_READ BIT(1) +#define PF_SB_REM_DEV_CTL_PHY0 BIT(2) + regval = rd32(hw, PF_SB_REM_DEV_CTL); + regval |= (PF_SB_REM_DEV_CTL_SWITCH_READ | + PF_SB_REM_DEV_CTL_PHY0); + wr32(hw, PF_SB_REM_DEV_CTL, regval); + + /* Initialize the Clock Generation Unit */ + err = ice_init_cgu_e822(hw); + if (err) + return err; + + /* Set window length for all the ports */ + return ice_ptp_set_vernier_wl(hw); +} + +/** + * ice_ptp_prep_phy_time_e822 - Prepare PHY port with initial time + * @hw: pointer to the HW struct + * @time: Time to initialize the PHY port clocks to + * + * Program the PHY port registers with a new initial time value. The port + * clock will be initialized once the driver issues an INIT_TIME sync + * command. The time value is the upper 32 bits of the PHY timer, usually in + * units of nominal nanoseconds. + */ +static int +ice_ptp_prep_phy_time_e822(struct ice_hw *hw, u32 time) +{ + u64 phy_time; + u8 port; + int err; + + /* The time represents the upper 32 bits of the PHY timer, so we need + * to shift to account for this when programming. + */ + phy_time = (u64)time << 32; + + for (port = 0; port < ICE_NUM_EXTERNAL_PORTS; port++) { + /* Tx case */ + err = ice_write_64b_phy_reg_e822(hw, port, + P_REG_TX_TIMER_INC_PRE_L, + phy_time); + if (err) + goto exit_err; + + /* Rx case */ + err = ice_write_64b_phy_reg_e822(hw, port, + P_REG_RX_TIMER_INC_PRE_L, + phy_time); + if (err) + goto exit_err; + } + + return 0; + +exit_err: + ice_debug(hw, ICE_DBG_PTP, "Failed to write init time for port %u, err %d\n", + port, err); + + return err; +} + +/** + * ice_ptp_prep_port_adj_e822 - Prepare a single port for time adjust + * @hw: pointer to HW struct + * @port: Port number to be programmed + * @time: time in cycles to adjust the port Tx and Rx clocks + * + * Program the port for an atomic adjustment by writing the Tx and Rx timer + * registers. The atomic adjustment won't be completed until the driver issues + * an ADJ_TIME command. + * + * Note that time is not in units of nanoseconds. It is in clock time + * including the lower sub-nanosecond portion of the port timer. + * + * Negative adjustments are supported using 2s complement arithmetic. + */ +int +ice_ptp_prep_port_adj_e822(struct ice_hw *hw, u8 port, s64 time) +{ + u32 l_time, u_time; + int err; + + l_time = lower_32_bits(time); + u_time = upper_32_bits(time); + + /* Tx case */ + err = ice_write_phy_reg_e822(hw, port, P_REG_TX_TIMER_INC_PRE_L, + l_time); + if (err) + goto exit_err; + + err = ice_write_phy_reg_e822(hw, port, P_REG_TX_TIMER_INC_PRE_U, + u_time); + if (err) + goto exit_err; + + /* Rx case */ + err = ice_write_phy_reg_e822(hw, port, P_REG_RX_TIMER_INC_PRE_L, + l_time); + if (err) + goto exit_err; + + err = ice_write_phy_reg_e822(hw, port, P_REG_RX_TIMER_INC_PRE_U, + u_time); + if (err) + goto exit_err; + + return 0; + +exit_err: + ice_debug(hw, ICE_DBG_PTP, "Failed to write time adjust for port %u, err %d\n", + port, err); + return err; +} + +/** + * ice_ptp_prep_phy_adj_e822 - Prep PHY ports for a time adjustment + * @hw: pointer to HW struct + * @adj: adjustment in nanoseconds + * + * Prepare the PHY ports for an atomic time adjustment by programming the PHY + * Tx and Rx port registers. The actual adjustment is completed by issuing an + * ADJ_TIME or ADJ_TIME_AT_TIME sync command. + */ +static int +ice_ptp_prep_phy_adj_e822(struct ice_hw *hw, s32 adj) +{ + s64 cycles; + u8 port; + + /* The port clock supports adjustment of the sub-nanosecond portion of + * the clock. We shift the provided adjustment in nanoseconds to + * calculate the appropriate adjustment to program into the PHY ports. + */ + if (adj > 0) + cycles = (s64)adj << 32; + else + cycles = -(((s64)-adj) << 32); + + for (port = 0; port < ICE_NUM_EXTERNAL_PORTS; port++) { + int err; + + err = ice_ptp_prep_port_adj_e822(hw, port, cycles); + if (err) + return err; + } + + return 0; +} + +/** + * ice_ptp_prep_phy_incval_e822 - Prepare PHY ports for time adjustment + * @hw: pointer to HW struct + * @incval: new increment value to prepare + * + * Prepare each of the PHY ports for a new increment value by programming the + * port's TIMETUS registers. The new increment value will be updated after + * issuing an INIT_INCVAL command. + */ +static int +ice_ptp_prep_phy_incval_e822(struct ice_hw *hw, u64 incval) +{ + int err; + u8 port; + + for (port = 0; port < ICE_NUM_EXTERNAL_PORTS; port++) { + err = ice_write_40b_phy_reg_e822(hw, port, P_REG_TIMETUS_L, + incval); + if (err) + goto exit_err; + } + + return 0; + +exit_err: + ice_debug(hw, ICE_DBG_PTP, "Failed to write incval for port %u, err %d\n", + port, err); + + return err; +} + +/** + * ice_ptp_read_port_capture - Read a port's local time capture + * @hw: pointer to HW struct + * @port: Port number to read + * @tx_ts: on return, the Tx port time capture + * @rx_ts: on return, the Rx port time capture + * + * Read the port's Tx and Rx local time capture values. + * + * Note this has no equivalent for the E810 devices. + */ +static int +ice_ptp_read_port_capture(struct ice_hw *hw, u8 port, u64 *tx_ts, u64 *rx_ts) +{ + int err; + + /* Tx case */ + err = ice_read_64b_phy_reg_e822(hw, port, P_REG_TX_CAPTURE_L, tx_ts); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read REG_TX_CAPTURE, err %d\n", + err); + return err; + } + + ice_debug(hw, ICE_DBG_PTP, "tx_init = 0x%016llx\n", + (unsigned long long)*tx_ts); + + /* Rx case */ + err = ice_read_64b_phy_reg_e822(hw, port, P_REG_RX_CAPTURE_L, rx_ts); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read RX_CAPTURE, err %d\n", + err); + return err; + } + + ice_debug(hw, ICE_DBG_PTP, "rx_init = 0x%016llx\n", + (unsigned long long)*rx_ts); + + return 0; +} + +/** + * ice_ptp_one_port_cmd - Prepare a single PHY port for a timer command + * @hw: pointer to HW struct + * @port: Port to which cmd has to be sent + * @cmd: Command to be sent to the port + * + * Prepare the requested port for an upcoming timer sync command. + * + * Note there is no equivalent of this operation on E810, as that device + * always handles all external PHYs internally. + */ +static int +ice_ptp_one_port_cmd(struct ice_hw *hw, u8 port, enum ice_ptp_tmr_cmd cmd) +{ + u32 cmd_val, val; + u8 tmr_idx; + int err; + + tmr_idx = ice_get_ptp_src_clock_index(hw); + cmd_val = tmr_idx << SEL_PHY_SRC; + switch (cmd) { + case INIT_TIME: + cmd_val |= PHY_CMD_INIT_TIME; + break; + case INIT_INCVAL: + cmd_val |= PHY_CMD_INIT_INCVAL; + break; + case ADJ_TIME: + cmd_val |= PHY_CMD_ADJ_TIME; + break; + case READ_TIME: + cmd_val |= PHY_CMD_READ_TIME; + break; + case ADJ_TIME_AT_TIME: + cmd_val |= PHY_CMD_ADJ_TIME_AT_TIME; + break; + } + + /* Tx case */ + /* Read, modify, write */ + err = ice_read_phy_reg_e822(hw, port, P_REG_TX_TMR_CMD, &val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read TX_TMR_CMD, err %d\n", + err); + return err; + } + + /* Modify necessary bits only and perform write */ + val &= ~TS_CMD_MASK; + val |= cmd_val; + + err = ice_write_phy_reg_e822(hw, port, P_REG_TX_TMR_CMD, val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write back TX_TMR_CMD, err %d\n", + err); + return err; + } + + /* Rx case */ + /* Read, modify, write */ + err = ice_read_phy_reg_e822(hw, port, P_REG_RX_TMR_CMD, &val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read RX_TMR_CMD, err %d\n", + err); + return err; + } + + /* Modify necessary bits only and perform write */ + val &= ~TS_CMD_MASK; + val |= cmd_val; + + err = ice_write_phy_reg_e822(hw, port, P_REG_RX_TMR_CMD, val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write back RX_TMR_CMD, err %d\n", + err); + return err; + } + + return 0; +} + +/** + * ice_ptp_port_cmd_e822 - Prepare all ports for a timer command + * @hw: pointer to the HW struct + * @cmd: timer command to prepare + * + * Prepare all ports connected to this device for an upcoming timer sync + * command. + */ +static int +ice_ptp_port_cmd_e822(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) +{ + u8 port; + + for (port = 0; port < ICE_NUM_EXTERNAL_PORTS; port++) { + int err; + + err = ice_ptp_one_port_cmd(hw, port, cmd); + if (err) + return err; + } + + return 0; +} + +/* E822 Vernier calibration functions + * + * The following functions are used as part of the vernier calibration of + * a port. This calibration increases the precision of the timestamps on the + * port. + */ + +/** + * ice_phy_get_speed_and_fec_e822 - Get link speed and FEC based on serdes mode + * @hw: pointer to HW struct + * @port: the port to read from + * @link_out: if non-NULL, holds link speed on success + * @fec_out: if non-NULL, holds FEC algorithm on success + * + * Read the serdes data for the PHY port and extract the link speed and FEC + * algorithm. + */ +static int +ice_phy_get_speed_and_fec_e822(struct ice_hw *hw, u8 port, + enum ice_ptp_link_spd *link_out, + enum ice_ptp_fec_mode *fec_out) +{ + enum ice_ptp_link_spd link; + enum ice_ptp_fec_mode fec; + u32 serdes; + int err; + + err = ice_read_phy_reg_e822(hw, port, P_REG_LINK_SPEED, &serdes); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read serdes info\n"); + return err; + } + + /* Determine the FEC algorithm */ + fec = (enum ice_ptp_fec_mode)P_REG_LINK_SPEED_FEC_MODE(serdes); + + serdes &= P_REG_LINK_SPEED_SERDES_M; + + /* Determine the link speed */ + if (fec == ICE_PTP_FEC_MODE_RS_FEC) { + switch (serdes) { + case ICE_PTP_SERDES_25G: + link = ICE_PTP_LNK_SPD_25G_RS; + break; + case ICE_PTP_SERDES_50G: + link = ICE_PTP_LNK_SPD_50G_RS; + break; + case ICE_PTP_SERDES_100G: + link = ICE_PTP_LNK_SPD_100G_RS; + break; + default: + return -EIO; + } + } else { + switch (serdes) { + case ICE_PTP_SERDES_1G: + link = ICE_PTP_LNK_SPD_1G; + break; + case ICE_PTP_SERDES_10G: + link = ICE_PTP_LNK_SPD_10G; + break; + case ICE_PTP_SERDES_25G: + link = ICE_PTP_LNK_SPD_25G; + break; + case ICE_PTP_SERDES_40G: + link = ICE_PTP_LNK_SPD_40G; + break; + case ICE_PTP_SERDES_50G: + link = ICE_PTP_LNK_SPD_50G; + break; + default: + return -EIO; + } + } + + if (link_out) + *link_out = link; + if (fec_out) + *fec_out = fec; + + return 0; +} + +/** + * ice_phy_cfg_lane_e822 - Configure PHY quad for single/multi-lane timestamp + * @hw: pointer to HW struct + * @port: to configure the quad for + */ +static void ice_phy_cfg_lane_e822(struct ice_hw *hw, u8 port) +{ + enum ice_ptp_link_spd link_spd; + int err; + u32 val; + u8 quad; + + err = ice_phy_get_speed_and_fec_e822(hw, port, &link_spd, NULL); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to get PHY link speed, err %d\n", + err); + return; + } + + quad = port / ICE_PORTS_PER_QUAD; + + err = ice_read_quad_reg_e822(hw, quad, Q_REG_TX_MEM_GBL_CFG, &val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read TX_MEM_GLB_CFG, err %d\n", + err); + return; + } + + if (link_spd >= ICE_PTP_LNK_SPD_40G) + val &= ~Q_REG_TX_MEM_GBL_CFG_LANE_TYPE_M; + else + val |= Q_REG_TX_MEM_GBL_CFG_LANE_TYPE_M; + + err = ice_write_quad_reg_e822(hw, quad, Q_REG_TX_MEM_GBL_CFG, val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write back TX_MEM_GBL_CFG, err %d\n", + err); + return; + } +} + +/** + * ice_phy_cfg_uix_e822 - Configure Serdes UI to TU conversion for E822 + * @hw: pointer to the HW structure + * @port: the port to configure + * + * Program the conversion ration of Serdes clock "unit intervals" (UIs) to PHC + * hardware clock time units (TUs). That is, determine the number of TUs per + * serdes unit interval, and program the UIX registers with this conversion. + * + * This conversion is used as part of the calibration process when determining + * the additional error of a timestamp vs the real time of transmission or + * receipt of the packet. + * + * Hardware uses the number of TUs per 66 UIs, written to the UIX registers + * for the two main serdes clock rates, 10G/40G and 25G/100G serdes clocks. + * + * To calculate the conversion ratio, we use the following facts: + * + * a) the clock frequency in Hz (cycles per second) + * b) the number of TUs per cycle (the increment value of the clock) + * c) 1 second per 1 billion nanoseconds + * d) the duration of 66 UIs in nanoseconds + * + * Given these facts, we can use the following table to work out what ratios + * to multiply in order to get the number of TUs per 66 UIs: + * + * cycles | 1 second | incval (TUs) | nanoseconds + * -------+--------------+--------------+------------- + * second | 1 billion ns | cycle | 66 UIs + * + * To perform the multiplication using integers without too much loss of + * precision, we can take use the following equation: + * + * (freq * incval * 6600 LINE_UI ) / ( 100 * 1 billion) + * + * We scale up to using 6600 UI instead of 66 in order to avoid fractional + * nanosecond UIs (66 UI at 10G/40G is 6.4 ns) + * + * The increment value has a maximum expected range of about 34 bits, while + * the frequency value is about 29 bits. Multiplying these values shouldn't + * overflow the 64 bits. However, we must then further multiply them again by + * the Serdes unit interval duration. To avoid overflow here, we split the + * overall divide by 1e11 into a divide by 256 (shift down by 8 bits) and + * a divide by 390,625,000. This does lose some precision, but avoids + * miscalculation due to arithmetic overflow. + */ +static int ice_phy_cfg_uix_e822(struct ice_hw *hw, u8 port) +{ + u64 cur_freq, clk_incval, tu_per_sec, uix; + int err; + + cur_freq = ice_e822_pll_freq(ice_e822_time_ref(hw)); + clk_incval = ice_ptp_read_src_incval(hw); + + /* Calculate TUs per second divided by 256 */ + tu_per_sec = (cur_freq * clk_incval) >> 8; + +#define LINE_UI_10G_40G 640 /* 6600 UIs is 640 nanoseconds at 10Gb/40Gb */ +#define LINE_UI_25G_100G 256 /* 6600 UIs is 256 nanoseconds at 25Gb/100Gb */ + + /* Program the 10Gb/40Gb conversion ratio */ + uix = div_u64(tu_per_sec * LINE_UI_10G_40G, 390625000); + + err = ice_write_64b_phy_reg_e822(hw, port, P_REG_UIX66_10G_40G_L, + uix); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write UIX66_10G_40G, err %d\n", + err); + return err; + } + + /* Program the 25Gb/100Gb conversion ratio */ + uix = div_u64(tu_per_sec * LINE_UI_25G_100G, 390625000); + + err = ice_write_64b_phy_reg_e822(hw, port, P_REG_UIX66_25G_100G_L, + uix); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write UIX66_25G_100G, err %d\n", + err); + return err; + } + + return 0; +} + +/** + * ice_phy_cfg_parpcs_e822 - Configure TUs per PAR/PCS clock cycle + * @hw: pointer to the HW struct + * @port: port to configure + * + * Configure the number of TUs for the PAR and PCS clocks used as part of the + * timestamp calibration process. This depends on the link speed, as the PHY + * uses different markers depending on the speed. + * + * 1Gb/10Gb/25Gb: + * - Tx/Rx PAR/PCS markers + * + * 25Gb RS: + * - Tx/Rx Reed Solomon gearbox PAR/PCS markers + * + * 40Gb/50Gb: + * - Tx/Rx PAR/PCS markers + * - Rx Deskew PAR/PCS markers + * + * 50G RS and 100GB RS: + * - Tx/Rx Reed Solomon gearbox PAR/PCS markers + * - Rx Deskew PAR/PCS markers + * - Tx PAR/PCS markers + * + * To calculate the conversion, we use the PHC clock frequency (cycles per + * second), the increment value (TUs per cycle), and the related PHY clock + * frequency to calculate the TUs per unit of the PHY link clock. The + * following table shows how the units convert: + * + * cycles | TUs | second + * -------+-------+-------- + * second | cycle | cycles + * + * For each conversion register, look up the appropriate frequency from the + * e822 PAR/PCS table and calculate the TUs per unit of that clock. Program + * this to the appropriate register, preparing hardware to perform timestamp + * calibration to calculate the total Tx or Rx offset to adjust the timestamp + * in order to calibrate for the internal PHY delays. + * + * Note that the increment value ranges up to ~34 bits, and the clock + * frequency is ~29 bits, so multiplying them together should fit within the + * 64 bit arithmetic. + */ +static int ice_phy_cfg_parpcs_e822(struct ice_hw *hw, u8 port) +{ + u64 cur_freq, clk_incval, tu_per_sec, phy_tus; + enum ice_ptp_link_spd link_spd; + enum ice_ptp_fec_mode fec_mode; + int err; + + err = ice_phy_get_speed_and_fec_e822(hw, port, &link_spd, &fec_mode); + if (err) + return err; + + cur_freq = ice_e822_pll_freq(ice_e822_time_ref(hw)); + clk_incval = ice_ptp_read_src_incval(hw); + + /* Calculate TUs per cycle of the PHC clock */ + tu_per_sec = cur_freq * clk_incval; + + /* For each PHY conversion register, look up the appropriate link + * speed frequency and determine the TUs per that clock's cycle time. + * Split this into a high and low value and then program the + * appropriate register. If that link speed does not use the + * associated register, write zeros to clear it instead. + */ + + /* P_REG_PAR_TX_TUS */ + if (e822_vernier[link_spd].tx_par_clk) + phy_tus = div_u64(tu_per_sec, + e822_vernier[link_spd].tx_par_clk); + else + phy_tus = 0; + + err = ice_write_40b_phy_reg_e822(hw, port, P_REG_PAR_TX_TUS_L, + phy_tus); + if (err) + return err; + + /* P_REG_PAR_RX_TUS */ + if (e822_vernier[link_spd].rx_par_clk) + phy_tus = div_u64(tu_per_sec, + e822_vernier[link_spd].rx_par_clk); + else + phy_tus = 0; + + err = ice_write_40b_phy_reg_e822(hw, port, P_REG_PAR_RX_TUS_L, + phy_tus); + if (err) + return err; + + /* P_REG_PCS_TX_TUS */ + if (e822_vernier[link_spd].tx_pcs_clk) + phy_tus = div_u64(tu_per_sec, + e822_vernier[link_spd].tx_pcs_clk); + else + phy_tus = 0; + + err = ice_write_40b_phy_reg_e822(hw, port, P_REG_PCS_TX_TUS_L, + phy_tus); + if (err) + return err; + + /* P_REG_PCS_RX_TUS */ + if (e822_vernier[link_spd].rx_pcs_clk) + phy_tus = div_u64(tu_per_sec, + e822_vernier[link_spd].rx_pcs_clk); + else + phy_tus = 0; + + err = ice_write_40b_phy_reg_e822(hw, port, P_REG_PCS_RX_TUS_L, + phy_tus); + if (err) + return err; + + /* P_REG_DESK_PAR_TX_TUS */ + if (e822_vernier[link_spd].tx_desk_rsgb_par) + phy_tus = div_u64(tu_per_sec, + e822_vernier[link_spd].tx_desk_rsgb_par); + else + phy_tus = 0; + + err = ice_write_40b_phy_reg_e822(hw, port, P_REG_DESK_PAR_TX_TUS_L, + phy_tus); + if (err) + return err; + + /* P_REG_DESK_PAR_RX_TUS */ + if (e822_vernier[link_spd].rx_desk_rsgb_par) + phy_tus = div_u64(tu_per_sec, + e822_vernier[link_spd].rx_desk_rsgb_par); + else + phy_tus = 0; + + err = ice_write_40b_phy_reg_e822(hw, port, P_REG_DESK_PAR_RX_TUS_L, + phy_tus); + if (err) + return err; + + /* P_REG_DESK_PCS_TX_TUS */ + if (e822_vernier[link_spd].tx_desk_rsgb_pcs) + phy_tus = div_u64(tu_per_sec, + e822_vernier[link_spd].tx_desk_rsgb_pcs); + else + phy_tus = 0; + + err = ice_write_40b_phy_reg_e822(hw, port, P_REG_DESK_PCS_TX_TUS_L, + phy_tus); + if (err) + return err; + + /* P_REG_DESK_PCS_RX_TUS */ + if (e822_vernier[link_spd].rx_desk_rsgb_pcs) + phy_tus = div_u64(tu_per_sec, + e822_vernier[link_spd].rx_desk_rsgb_pcs); + else + phy_tus = 0; + + return ice_write_40b_phy_reg_e822(hw, port, P_REG_DESK_PCS_RX_TUS_L, + phy_tus); +} + +/** + * ice_calc_fixed_tx_offset_e822 - Calculated Fixed Tx offset for a port + * @hw: pointer to the HW struct + * @link_spd: the Link speed to calculate for + * + * Calculate the fixed offset due to known static latency data. + */ +static u64 +ice_calc_fixed_tx_offset_e822(struct ice_hw *hw, enum ice_ptp_link_spd link_spd) +{ + u64 cur_freq, clk_incval, tu_per_sec, fixed_offset; + + cur_freq = ice_e822_pll_freq(ice_e822_time_ref(hw)); + clk_incval = ice_ptp_read_src_incval(hw); + + /* Calculate TUs per second */ + tu_per_sec = cur_freq * clk_incval; + + /* Calculate number of TUs to add for the fixed Tx latency. Since the + * latency measurement is in 1/100th of a nanosecond, we need to + * multiply by tu_per_sec and then divide by 1e11. This calculation + * overflows 64 bit integer arithmetic, so break it up into two + * divisions by 1e4 first then by 1e7. + */ + fixed_offset = div_u64(tu_per_sec, 10000); + fixed_offset *= e822_vernier[link_spd].tx_fixed_delay; + fixed_offset = div_u64(fixed_offset, 10000000); + + return fixed_offset; +} + +/** + * ice_phy_cfg_tx_offset_e822 - Configure total Tx timestamp offset + * @hw: pointer to the HW struct + * @port: the PHY port to configure + * + * Program the P_REG_TOTAL_TX_OFFSET register with the total number of TUs to + * adjust Tx timestamps by. This is calculated by combining some known static + * latency along with the Vernier offset computations done by hardware. + * + * This function must be called only after the offset registers are valid, + * i.e. after the Vernier calibration wait has passed, to ensure that the PHY + * has measured the offset. + * + * To avoid overflow, when calculating the offset based on the known static + * latency values, we use measurements in 1/100th of a nanosecond, and divide + * the TUs per second up front. This avoids overflow while allowing + * calculation of the adjustment using integer arithmetic. + */ +static int ice_phy_cfg_tx_offset_e822(struct ice_hw *hw, u8 port) +{ + enum ice_ptp_link_spd link_spd; + enum ice_ptp_fec_mode fec_mode; + u64 total_offset, val; + int err; + + err = ice_phy_get_speed_and_fec_e822(hw, port, &link_spd, &fec_mode); + if (err) + return err; + + total_offset = ice_calc_fixed_tx_offset_e822(hw, link_spd); + + /* Read the first Vernier offset from the PHY register and add it to + * the total offset. + */ + if (link_spd == ICE_PTP_LNK_SPD_1G || + link_spd == ICE_PTP_LNK_SPD_10G || + link_spd == ICE_PTP_LNK_SPD_25G || + link_spd == ICE_PTP_LNK_SPD_25G_RS || + link_spd == ICE_PTP_LNK_SPD_40G || + link_spd == ICE_PTP_LNK_SPD_50G) { + err = ice_read_64b_phy_reg_e822(hw, port, + P_REG_PAR_PCS_TX_OFFSET_L, + &val); + if (err) + return err; + + total_offset += val; + } + + /* For Tx, we only need to use the second Vernier offset for + * multi-lane link speeds with RS-FEC. The lanes will always be + * aligned. + */ + if (link_spd == ICE_PTP_LNK_SPD_50G_RS || + link_spd == ICE_PTP_LNK_SPD_100G_RS) { + err = ice_read_64b_phy_reg_e822(hw, port, + P_REG_PAR_TX_TIME_L, + &val); + if (err) + return err; + + total_offset += val; + } + + /* Now that the total offset has been calculated, program it to the + * PHY and indicate that the Tx offset is ready. After this, + * timestamps will be enabled. + */ + err = ice_write_64b_phy_reg_e822(hw, port, P_REG_TOTAL_TX_OFFSET_L, + total_offset); + if (err) + return err; + + err = ice_write_phy_reg_e822(hw, port, P_REG_TX_OR, 1); + if (err) + return err; + + return 0; +} + +/** + * ice_phy_cfg_fixed_tx_offset_e822 - Configure Tx offset for bypass mode + * @hw: pointer to the HW struct + * @port: the PHY port to configure + * + * Calculate and program the fixed Tx offset, and indicate that the offset is + * ready. This can be used when operating in bypass mode. + */ +static int +ice_phy_cfg_fixed_tx_offset_e822(struct ice_hw *hw, u8 port) +{ + enum ice_ptp_link_spd link_spd; + enum ice_ptp_fec_mode fec_mode; + u64 total_offset; + int err; + + err = ice_phy_get_speed_and_fec_e822(hw, port, &link_spd, &fec_mode); + if (err) + return err; + + total_offset = ice_calc_fixed_tx_offset_e822(hw, link_spd); + + /* Program the fixed Tx offset into the P_REG_TOTAL_TX_OFFSET_L + * register, then indicate that the Tx offset is ready. After this, + * timestamps will be enabled. + * + * Note that this skips including the more precise offsets generated + * by the Vernier calibration. + */ + err = ice_write_64b_phy_reg_e822(hw, port, P_REG_TOTAL_TX_OFFSET_L, + total_offset); + if (err) + return err; + + err = ice_write_phy_reg_e822(hw, port, P_REG_TX_OR, 1); + if (err) + return err; + + return 0; +} + +/** + * ice_phy_calc_pmd_adj_e822 - Calculate PMD adjustment for Rx + * @hw: pointer to the HW struct + * @port: the PHY port to adjust for + * @link_spd: the current link speed of the PHY + * @fec_mode: the current FEC mode of the PHY + * @pmd_adj: on return, the amount to adjust the Rx total offset by + * + * Calculates the adjustment to Rx timestamps due to PMD alignment in the PHY. + * This varies by link speed and FEC mode. The value calculated accounts for + * various delays caused when receiving a packet. + */ +static int +ice_phy_calc_pmd_adj_e822(struct ice_hw *hw, u8 port, + enum ice_ptp_link_spd link_spd, + enum ice_ptp_fec_mode fec_mode, u64 *pmd_adj) +{ + u64 cur_freq, clk_incval, tu_per_sec, mult, adj; + u8 pmd_align; + u32 val; + int err; + + err = ice_read_phy_reg_e822(hw, port, P_REG_PMD_ALIGNMENT, &val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read PMD alignment, err %d\n", + err); + return err; + } + + pmd_align = (u8)val; + + cur_freq = ice_e822_pll_freq(ice_e822_time_ref(hw)); + clk_incval = ice_ptp_read_src_incval(hw); + + /* Calculate TUs per second */ + tu_per_sec = cur_freq * clk_incval; + + /* The PMD alignment adjustment measurement depends on the link speed, + * and whether FEC is enabled. For each link speed, the alignment + * adjustment is calculated by dividing a value by the length of + * a Time Unit in nanoseconds. + * + * 1G: align == 4 ? 10 * 0.8 : (align + 6 % 10) * 0.8 + * 10G: align == 65 ? 0 : (align * 0.1 * 32/33) + * 10G w/FEC: align * 0.1 * 32/33 + * 25G: align == 65 ? 0 : (align * 0.4 * 32/33) + * 25G w/FEC: align * 0.4 * 32/33 + * 40G: align == 65 ? 0 : (align * 0.1 * 32/33) + * 40G w/FEC: align * 0.1 * 32/33 + * 50G: align == 65 ? 0 : (align * 0.4 * 32/33) + * 50G w/FEC: align * 0.8 * 32/33 + * + * For RS-FEC, if align is < 17 then we must also add 1.6 * 32/33. + * + * To allow for calculating this value using integer arithmetic, we + * instead start with the number of TUs per second, (inverse of the + * length of a Time Unit in nanoseconds), multiply by a value based + * on the PMD alignment register, and then divide by the right value + * calculated based on the table above. To avoid integer overflow this + * division is broken up into a step of dividing by 125 first. + */ + if (link_spd == ICE_PTP_LNK_SPD_1G) { + if (pmd_align == 4) + mult = 10; + else + mult = (pmd_align + 6) % 10; + } else if (link_spd == ICE_PTP_LNK_SPD_10G || + link_spd == ICE_PTP_LNK_SPD_25G || + link_spd == ICE_PTP_LNK_SPD_40G || + link_spd == ICE_PTP_LNK_SPD_50G) { + /* If Clause 74 FEC, always calculate PMD adjust */ + if (pmd_align != 65 || fec_mode == ICE_PTP_FEC_MODE_CLAUSE74) + mult = pmd_align; + else + mult = 0; + } else if (link_spd == ICE_PTP_LNK_SPD_25G_RS || + link_spd == ICE_PTP_LNK_SPD_50G_RS || + link_spd == ICE_PTP_LNK_SPD_100G_RS) { + if (pmd_align < 17) + mult = pmd_align + 40; + else + mult = pmd_align; + } else { + ice_debug(hw, ICE_DBG_PTP, "Unknown link speed %d, skipping PMD adjustment\n", + link_spd); + mult = 0; + } + + /* In some cases, there's no need to adjust for the PMD alignment */ + if (!mult) { + *pmd_adj = 0; + return 0; + } + + /* Calculate the adjustment by multiplying TUs per second by the + * appropriate multiplier and divisor. To avoid overflow, we first + * divide by 125, and then handle remaining divisor based on the link + * speed pmd_adj_divisor value. + */ + adj = div_u64(tu_per_sec, 125); + adj *= mult; + adj = div_u64(adj, e822_vernier[link_spd].pmd_adj_divisor); + + /* Finally, for 25G-RS and 50G-RS, a further adjustment for the Rx + * cycle count is necessary. + */ + if (link_spd == ICE_PTP_LNK_SPD_25G_RS) { + u64 cycle_adj; + u8 rx_cycle; + + err = ice_read_phy_reg_e822(hw, port, P_REG_RX_40_TO_160_CNT, + &val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read 25G-RS Rx cycle count, err %d\n", + err); + return err; + } + + rx_cycle = val & P_REG_RX_40_TO_160_CNT_RXCYC_M; + if (rx_cycle) { + mult = (4 - rx_cycle) * 40; + + cycle_adj = div_u64(tu_per_sec, 125); + cycle_adj *= mult; + cycle_adj = div_u64(cycle_adj, e822_vernier[link_spd].pmd_adj_divisor); + + adj += cycle_adj; + } + } else if (link_spd == ICE_PTP_LNK_SPD_50G_RS) { + u64 cycle_adj; + u8 rx_cycle; + + err = ice_read_phy_reg_e822(hw, port, P_REG_RX_80_TO_160_CNT, + &val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read 50G-RS Rx cycle count, err %d\n", + err); + return err; + } + + rx_cycle = val & P_REG_RX_80_TO_160_CNT_RXCYC_M; + if (rx_cycle) { + mult = rx_cycle * 40; + + cycle_adj = div_u64(tu_per_sec, 125); + cycle_adj *= mult; + cycle_adj = div_u64(cycle_adj, e822_vernier[link_spd].pmd_adj_divisor); + + adj += cycle_adj; + } + } + + /* Return the calculated adjustment */ + *pmd_adj = adj; + + return 0; +} + +/** + * ice_calc_fixed_rx_offset_e822 - Calculated the fixed Rx offset for a port + * @hw: pointer to HW struct + * @link_spd: The Link speed to calculate for + * + * Determine the fixed Rx latency for a given link speed. + */ +static u64 +ice_calc_fixed_rx_offset_e822(struct ice_hw *hw, enum ice_ptp_link_spd link_spd) +{ + u64 cur_freq, clk_incval, tu_per_sec, fixed_offset; + + cur_freq = ice_e822_pll_freq(ice_e822_time_ref(hw)); + clk_incval = ice_ptp_read_src_incval(hw); + + /* Calculate TUs per second */ + tu_per_sec = cur_freq * clk_incval; + + /* Calculate number of TUs to add for the fixed Rx latency. Since the + * latency measurement is in 1/100th of a nanosecond, we need to + * multiply by tu_per_sec and then divide by 1e11. This calculation + * overflows 64 bit integer arithmetic, so break it up into two + * divisions by 1e4 first then by 1e7. + */ + fixed_offset = div_u64(tu_per_sec, 10000); + fixed_offset *= e822_vernier[link_spd].rx_fixed_delay; + fixed_offset = div_u64(fixed_offset, 10000000); + + return fixed_offset; +} + +/** + * ice_phy_cfg_rx_offset_e822 - Configure total Rx timestamp offset + * @hw: pointer to the HW struct + * @port: the PHY port to configure + * + * Program the P_REG_TOTAL_RX_OFFSET register with the number of Time Units to + * adjust Rx timestamps by. This combines calculations from the Vernier offset + * measurements taken in hardware with some data about known fixed delay as + * well as adjusting for multi-lane alignment delay. + * + * This function must be called only after the offset registers are valid, + * i.e. after the Vernier calibration wait has passed, to ensure that the PHY + * has measured the offset. + * + * To avoid overflow, when calculating the offset based on the known static + * latency values, we use measurements in 1/100th of a nanosecond, and divide + * the TUs per second up front. This avoids overflow while allowing + * calculation of the adjustment using integer arithmetic. + */ +static int ice_phy_cfg_rx_offset_e822(struct ice_hw *hw, u8 port) +{ + enum ice_ptp_link_spd link_spd; + enum ice_ptp_fec_mode fec_mode; + u64 total_offset, pmd, val; + int err; + + err = ice_phy_get_speed_and_fec_e822(hw, port, &link_spd, &fec_mode); + if (err) + return err; + + total_offset = ice_calc_fixed_rx_offset_e822(hw, link_spd); + + /* Read the first Vernier offset from the PHY register and add it to + * the total offset. + */ + err = ice_read_64b_phy_reg_e822(hw, port, + P_REG_PAR_PCS_RX_OFFSET_L, + &val); + if (err) + return err; + + total_offset += val; + + /* For Rx, all multi-lane link speeds include a second Vernier + * calibration, because the lanes might not be aligned. + */ + if (link_spd == ICE_PTP_LNK_SPD_40G || + link_spd == ICE_PTP_LNK_SPD_50G || + link_spd == ICE_PTP_LNK_SPD_50G_RS || + link_spd == ICE_PTP_LNK_SPD_100G_RS) { + err = ice_read_64b_phy_reg_e822(hw, port, + P_REG_PAR_RX_TIME_L, + &val); + if (err) + return err; + + total_offset += val; + } + + /* In addition, Rx must account for the PMD alignment */ + err = ice_phy_calc_pmd_adj_e822(hw, port, link_spd, fec_mode, &pmd); + if (err) + return err; + + /* For RS-FEC, this adjustment adds delay, but for other modes, it + * subtracts delay. + */ + if (fec_mode == ICE_PTP_FEC_MODE_RS_FEC) + total_offset += pmd; + else + total_offset -= pmd; + + /* Now that the total offset has been calculated, program it to the + * PHY and indicate that the Rx offset is ready. After this, + * timestamps will be enabled. + */ + err = ice_write_64b_phy_reg_e822(hw, port, P_REG_TOTAL_RX_OFFSET_L, + total_offset); + if (err) + return err; + + err = ice_write_phy_reg_e822(hw, port, P_REG_RX_OR, 1); + if (err) + return err; + + return 0; +} + +/** + * ice_phy_cfg_fixed_rx_offset_e822 - Configure fixed Rx offset for bypass mode + * @hw: pointer to the HW struct + * @port: the PHY port to configure + * + * Calculate and program the fixed Rx offset, and indicate that the offset is + * ready. This can be used when operating in bypass mode. + */ +static int +ice_phy_cfg_fixed_rx_offset_e822(struct ice_hw *hw, u8 port) +{ + enum ice_ptp_link_spd link_spd; + enum ice_ptp_fec_mode fec_mode; + u64 total_offset; + int err; + + err = ice_phy_get_speed_and_fec_e822(hw, port, &link_spd, &fec_mode); + if (err) + return err; + + total_offset = ice_calc_fixed_rx_offset_e822(hw, link_spd); + + /* Program the fixed Rx offset into the P_REG_TOTAL_RX_OFFSET_L + * register, then indicate that the Rx offset is ready. After this, + * timestamps will be enabled. + * + * Note that this skips including the more precise offsets generated + * by Vernier calibration. + */ + err = ice_write_64b_phy_reg_e822(hw, port, P_REG_TOTAL_RX_OFFSET_L, + total_offset); + if (err) + return err; + + err = ice_write_phy_reg_e822(hw, port, P_REG_RX_OR, 1); + if (err) + return err; + + return 0; +} + +/** + * ice_read_phy_and_phc_time_e822 - Simultaneously capture PHC and PHY time + * @hw: pointer to the HW struct + * @port: the PHY port to read + * @phy_time: on return, the 64bit PHY timer value + * @phc_time: on return, the lower 64bits of PHC time + * + * Issue a READ_TIME timer command to simultaneously capture the PHY and PHC + * timer values. + */ +static int +ice_read_phy_and_phc_time_e822(struct ice_hw *hw, u8 port, u64 *phy_time, + u64 *phc_time) +{ + u64 tx_time, rx_time; + u32 zo, lo; + u8 tmr_idx; + int err; + + tmr_idx = ice_get_ptp_src_clock_index(hw); + + /* Prepare the PHC timer for a READ_TIME capture command */ + ice_ptp_src_cmd(hw, READ_TIME); + + /* Prepare the PHY timer for a READ_TIME capture command */ + err = ice_ptp_one_port_cmd(hw, port, READ_TIME); + if (err) + return err; + + /* Issue the sync to start the READ_TIME capture */ + ice_ptp_exec_tmr_cmd(hw); + + /* Read the captured PHC time from the shadow time registers */ + zo = rd32(hw, GLTSYN_SHTIME_0(tmr_idx)); + lo = rd32(hw, GLTSYN_SHTIME_L(tmr_idx)); + *phc_time = (u64)lo << 32 | zo; + + /* Read the captured PHY time from the PHY shadow registers */ + err = ice_ptp_read_port_capture(hw, port, &tx_time, &rx_time); + if (err) + return err; + + /* If the PHY Tx and Rx timers don't match, log a warning message. + * Note that this should not happen in normal circumstances since the + * driver always programs them together. + */ + if (tx_time != rx_time) + dev_warn(ice_hw_to_dev(hw), + "PHY port %u Tx and Rx timers do not match, tx_time 0x%016llX, rx_time 0x%016llX\n", + port, (unsigned long long)tx_time, + (unsigned long long)rx_time); + + *phy_time = tx_time; + + return 0; +} + +/** + * ice_sync_phy_timer_e822 - Synchronize the PHY timer with PHC timer + * @hw: pointer to the HW struct + * @port: the PHY port to synchronize + * + * Perform an adjustment to ensure that the PHY and PHC timers are in sync. + * This is done by issuing a READ_TIME command which triggers a simultaneous + * read of the PHY timer and PHC timer. Then we use the difference to + * calculate an appropriate 2s complement addition to add to the PHY timer in + * order to ensure it reads the same value as the primary PHC timer. + */ +static int ice_sync_phy_timer_e822(struct ice_hw *hw, u8 port) +{ + u64 phc_time, phy_time, difference; + int err; + + if (!ice_ptp_lock(hw)) { + ice_debug(hw, ICE_DBG_PTP, "Failed to acquire PTP semaphore\n"); + return -EBUSY; + } + + err = ice_read_phy_and_phc_time_e822(hw, port, &phy_time, &phc_time); + if (err) + goto err_unlock; + + /* Calculate the amount required to add to the port time in order for + * it to match the PHC time. + * + * Note that the port adjustment is done using 2s complement + * arithmetic. This is convenient since it means that we can simply + * calculate the difference between the PHC time and the port time, + * and it will be interpreted correctly. + */ + difference = phc_time - phy_time; + + err = ice_ptp_prep_port_adj_e822(hw, port, (s64)difference); + if (err) + goto err_unlock; + + err = ice_ptp_one_port_cmd(hw, port, ADJ_TIME); + if (err) + goto err_unlock; + + /* Issue the sync to activate the time adjustment */ + ice_ptp_exec_tmr_cmd(hw); + + /* Re-capture the timer values to flush the command registers and + * verify that the time was properly adjusted. + */ + err = ice_read_phy_and_phc_time_e822(hw, port, &phy_time, &phc_time); + if (err) + goto err_unlock; + + dev_info(ice_hw_to_dev(hw), + "Port %u PHY time synced to PHC: 0x%016llX, 0x%016llX\n", + port, (unsigned long long)phy_time, + (unsigned long long)phc_time); + + ice_ptp_unlock(hw); + + return 0; + +err_unlock: + ice_ptp_unlock(hw); + return err; +} + +/** + * ice_stop_phy_timer_e822 - Stop the PHY clock timer + * @hw: pointer to the HW struct + * @port: the PHY port to stop + * @soft_reset: if true, hold the SOFT_RESET bit of P_REG_PS + * + * Stop the clock of a PHY port. This must be done as part of the flow to + * re-calibrate Tx and Rx timestamping offsets whenever the clock time is + * initialized or when link speed changes. + */ +int +ice_stop_phy_timer_e822(struct ice_hw *hw, u8 port, bool soft_reset) +{ + int err; + u32 val; + + err = ice_write_phy_reg_e822(hw, port, P_REG_TX_OR, 0); + if (err) + return err; + + err = ice_write_phy_reg_e822(hw, port, P_REG_RX_OR, 0); + if (err) + return err; + + err = ice_read_phy_reg_e822(hw, port, P_REG_PS, &val); + if (err) + return err; + + val &= ~P_REG_PS_START_M; + err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); + if (err) + return err; + + val &= ~P_REG_PS_ENA_CLK_M; + err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); + if (err) + return err; + + if (soft_reset) { + val |= P_REG_PS_SFT_RESET_M; + err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); + if (err) + return err; + } + + ice_debug(hw, ICE_DBG_PTP, "Disabled clock on PHY port %u\n", port); + + return 0; +} + +/** + * ice_start_phy_timer_e822 - Start the PHY clock timer + * @hw: pointer to the HW struct + * @port: the PHY port to start + * @bypass: if true, start the PHY in bypass mode + * + * Start the clock of a PHY port. This must be done as part of the flow to + * re-calibrate Tx and Rx timestamping offsets whenever the clock time is + * initialized or when link speed changes. + * + * Bypass mode enables timestamps immediately without waiting for Vernier + * calibration to complete. Hardware will still continue taking Vernier + * measurements on Tx or Rx of packets, but they will not be applied to + * timestamps. Use ice_phy_exit_bypass_e822 to exit bypass mode once hardware + * has completed offset calculation. + */ +int +ice_start_phy_timer_e822(struct ice_hw *hw, u8 port, bool bypass) +{ + u32 lo, hi, val; + u64 incval; + u8 tmr_idx; + int err; + + tmr_idx = ice_get_ptp_src_clock_index(hw); + + err = ice_stop_phy_timer_e822(hw, port, false); + if (err) + return err; + + ice_phy_cfg_lane_e822(hw, port); + + err = ice_phy_cfg_uix_e822(hw, port); + if (err) + return err; + + err = ice_phy_cfg_parpcs_e822(hw, port); + if (err) + return err; + + lo = rd32(hw, GLTSYN_INCVAL_L(tmr_idx)); + hi = rd32(hw, GLTSYN_INCVAL_H(tmr_idx)); + incval = (u64)hi << 32 | lo; + + err = ice_write_40b_phy_reg_e822(hw, port, P_REG_TIMETUS_L, incval); + if (err) + return err; + + err = ice_ptp_one_port_cmd(hw, port, INIT_INCVAL); + if (err) + return err; + + ice_ptp_exec_tmr_cmd(hw); + + err = ice_read_phy_reg_e822(hw, port, P_REG_PS, &val); + if (err) + return err; + + val |= P_REG_PS_SFT_RESET_M; + err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); + if (err) + return err; + + val |= P_REG_PS_START_M; + err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); + if (err) + return err; + + val &= ~P_REG_PS_SFT_RESET_M; + err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); + if (err) + return err; + + err = ice_ptp_one_port_cmd(hw, port, INIT_INCVAL); + if (err) + return err; + + ice_ptp_exec_tmr_cmd(hw); + + val |= P_REG_PS_ENA_CLK_M; + err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); + if (err) + return err; + + val |= P_REG_PS_LOAD_OFFSET_M; + err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); + if (err) + return err; + + ice_ptp_exec_tmr_cmd(hw); + + err = ice_sync_phy_timer_e822(hw, port); + if (err) + return err; + + if (bypass) { + val |= P_REG_PS_BYPASS_MODE_M; + /* Enter BYPASS mode, enabling timestamps immediately. */ + err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); + if (err) + return err; + + /* Program the fixed Tx offset */ + err = ice_phy_cfg_fixed_tx_offset_e822(hw, port); + if (err) + return err; + + /* Program the fixed Rx offset */ + err = ice_phy_cfg_fixed_rx_offset_e822(hw, port); + if (err) + return err; + } + + ice_debug(hw, ICE_DBG_PTP, "Enabled clock on PHY port %u\n", port); + + return 0; +} + +/** + * ice_phy_exit_bypass_e822 - Exit bypass mode, after vernier calculations + * @hw: pointer to the HW struct + * @port: the PHY port to configure + * + * After hardware finishes vernier calculations for the Tx and Rx offset, this + * function can be used to exit bypass mode by updating the total Tx and Rx + * offsets, and then disabling bypass. This will enable hardware to include + * the more precise offset calibrations, increasing precision of the generated + * timestamps. + * + * This cannot be done until hardware has measured the offsets, which requires + * waiting until at least one packet has been sent and received by the device. + */ +int ice_phy_exit_bypass_e822(struct ice_hw *hw, u8 port) +{ + int err; + u32 val; + + err = ice_read_phy_reg_e822(hw, port, P_REG_TX_OV_STATUS, &val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read TX_OV_STATUS for port %u, err %d\n", + port, err); + return err; + } + + if (!(val & P_REG_TX_OV_STATUS_OV_M)) { + ice_debug(hw, ICE_DBG_PTP, "Tx offset is not yet valid for port %u\n", + port); + return -EBUSY; + } + + err = ice_read_phy_reg_e822(hw, port, P_REG_RX_OV_STATUS, &val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read RX_OV_STATUS for port %u, err %d\n", + port, err); + return err; + } + + if (!(val & P_REG_TX_OV_STATUS_OV_M)) { + ice_debug(hw, ICE_DBG_PTP, "Rx offset is not yet valid for port %u\n", + port); + return -EBUSY; + } + + err = ice_phy_cfg_tx_offset_e822(hw, port); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to program total Tx offset for port %u, err %d\n", + port, err); + return err; + } + + err = ice_phy_cfg_rx_offset_e822(hw, port); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to program total Rx offset for port %u, err %d\n", + port, err); + return err; + } + + /* Exit bypass mode now that the offset has been updated */ + err = ice_read_phy_reg_e822(hw, port, P_REG_PS, &val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read P_REG_PS for port %u, err %d\n", + port, err); + return err; + } + + if (!(val & P_REG_PS_BYPASS_MODE_M)) + ice_debug(hw, ICE_DBG_PTP, "Port %u not in bypass mode\n", + port); + + val &= ~P_REG_PS_BYPASS_MODE_M; + err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to disable bypass for port %u, err %d\n", + port, err); + return err; + } + + dev_info(ice_hw_to_dev(hw), "Exiting bypass mode on PHY port %u\n", + port); + + return 0; +} + /* E810 functions * * The following functions operate on the E810 series devices which use @@ -68,18 +2539,18 @@ u8 ice_get_ptp_src_clock_index(struct ice_hw *hw) static int ice_read_phy_reg_e810(struct ice_hw *hw, u32 addr, u32 *val) { struct ice_sbq_msg_input msg = {0}; - int status; + int err; msg.msg_addr_low = lower_16_bits(addr); msg.msg_addr_high = upper_16_bits(addr); msg.opcode = ice_sbq_msg_rd; msg.dest_dev = rmn_0; - status = ice_sbq_rw_reg(hw, &msg); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to send message to PHY, status %d\n", - status); - return status; + err = ice_sbq_rw_reg(hw, &msg); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to send message to PHY, err %d\n", + err); + return err; } *val = msg.data; @@ -98,7 +2569,7 @@ static int ice_read_phy_reg_e810(struct ice_hw *hw, u32 addr, u32 *val) static int ice_write_phy_reg_e810(struct ice_hw *hw, u32 addr, u32 val) { struct ice_sbq_msg_input msg = {0}; - int status; + int err; msg.msg_addr_low = lower_16_bits(addr); msg.msg_addr_high = upper_16_bits(addr); @@ -106,17 +2577,100 @@ static int ice_write_phy_reg_e810(struct ice_hw *hw, u32 addr, u32 val) msg.dest_dev = rmn_0; msg.data = val; - status = ice_sbq_rw_reg(hw, &msg); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to send message to PHY, status %d\n", - status); - return status; + err = ice_sbq_rw_reg(hw, &msg); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to send message to PHY, err %d\n", + err); + return err; } return 0; } /** + * ice_read_phy_tstamp_ll_e810 - Read a PHY timestamp registers through the FW + * @hw: pointer to the HW struct + * @idx: the timestamp index to read + * @hi: 8 bit timestamp high value + * @lo: 32 bit timestamp low value + * + * Read a 8bit timestamp high value and 32 bit timestamp low value out of the + * timestamp block of the external PHY on the E810 device using the low latency + * timestamp read. + */ +static int +ice_read_phy_tstamp_ll_e810(struct ice_hw *hw, u8 idx, u8 *hi, u32 *lo) +{ + u32 val; + u8 i; + + /* Write TS index to read to the PF register so the FW can read it */ + val = FIELD_PREP(TS_LL_READ_TS_IDX, idx) | TS_LL_READ_TS; + wr32(hw, PF_SB_ATQBAL, val); + + /* Read the register repeatedly until the FW provides us the TS */ + for (i = TS_LL_READ_RETRIES; i > 0; i--) { + val = rd32(hw, PF_SB_ATQBAL); + + /* When the bit is cleared, the TS is ready in the register */ + if (!(FIELD_GET(TS_LL_READ_TS, val))) { + /* High 8 bit value of the TS is on the bits 16:23 */ + *hi = FIELD_GET(TS_LL_READ_TS_HIGH, val); + + /* Read the low 32 bit value and set the TS valid bit */ + *lo = rd32(hw, PF_SB_ATQBAH) | TS_VALID; + return 0; + } + + udelay(10); + } + + /* FW failed to provide the TS in time */ + ice_debug(hw, ICE_DBG_PTP, "Failed to read PTP timestamp using low latency read\n"); + return -EINVAL; +} + +/** + * ice_read_phy_tstamp_sbq_e810 - Read a PHY timestamp registers through the sbq + * @hw: pointer to the HW struct + * @lport: the lport to read from + * @idx: the timestamp index to read + * @hi: 8 bit timestamp high value + * @lo: 32 bit timestamp low value + * + * Read a 8bit timestamp high value and 32 bit timestamp low value out of the + * timestamp block of the external PHY on the E810 device using sideband queue. + */ +static int +ice_read_phy_tstamp_sbq_e810(struct ice_hw *hw, u8 lport, u8 idx, u8 *hi, + u32 *lo) +{ + u32 hi_addr = TS_EXT(HIGH_TX_MEMORY_BANK_START, lport, idx); + u32 lo_addr = TS_EXT(LOW_TX_MEMORY_BANK_START, lport, idx); + u32 lo_val, hi_val; + int err; + + err = ice_read_phy_reg_e810(hw, lo_addr, &lo_val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read low PTP timestamp register, err %d\n", + err); + return err; + } + + err = ice_read_phy_reg_e810(hw, hi_addr, &hi_val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read high PTP timestamp register, err %d\n", + err); + return err; + } + + *lo = lo_val; + *hi = (u8)hi_val; + + return 0; +} + +/** * ice_read_phy_tstamp_e810 - Read a PHY timestamp out of the external PHY * @hw: pointer to the HW struct * @lport: the lport to read from @@ -129,25 +2683,17 @@ static int ice_write_phy_reg_e810(struct ice_hw *hw, u32 addr, u32 val) static int ice_read_phy_tstamp_e810(struct ice_hw *hw, u8 lport, u8 idx, u64 *tstamp) { - u32 lo_addr, hi_addr, lo, hi; - int status; - - lo_addr = TS_EXT(LOW_TX_MEMORY_BANK_START, lport, idx); - hi_addr = TS_EXT(HIGH_TX_MEMORY_BANK_START, lport, idx); + u32 lo = 0; + u8 hi = 0; + int err; - status = ice_read_phy_reg_e810(hw, lo_addr, &lo); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to read low PTP timestamp register, status %d\n", - status); - return status; - } + if (hw->dev_caps.ts_dev_info.ts_ll_read) + err = ice_read_phy_tstamp_ll_e810(hw, idx, &hi, &lo); + else + err = ice_read_phy_tstamp_sbq_e810(hw, lport, idx, &hi, &lo); - status = ice_read_phy_reg_e810(hw, hi_addr, &hi); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to read high PTP timestamp register, status %d\n", - status); - return status; - } + if (err) + return err; /* For E810 devices, the timestamp is reported with the lower 32 bits * in the low register, and the upper 8 bits in the high register. @@ -169,23 +2715,23 @@ ice_read_phy_tstamp_e810(struct ice_hw *hw, u8 lport, u8 idx, u64 *tstamp) static int ice_clear_phy_tstamp_e810(struct ice_hw *hw, u8 lport, u8 idx) { u32 lo_addr, hi_addr; - int status; + int err; lo_addr = TS_EXT(LOW_TX_MEMORY_BANK_START, lport, idx); hi_addr = TS_EXT(HIGH_TX_MEMORY_BANK_START, lport, idx); - status = ice_write_phy_reg_e810(hw, lo_addr, 0); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to clear low PTP timestamp register, status %d\n", - status); - return status; + err = ice_write_phy_reg_e810(hw, lo_addr, 0); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to clear low PTP timestamp register, err %d\n", + err); + return err; } - status = ice_write_phy_reg_e810(hw, hi_addr, 0); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to clear high PTP timestamp register, status %d\n", - status); - return status; + err = ice_write_phy_reg_e810(hw, hi_addr, 0); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to clear high PTP timestamp register, err %d\n", + err); + return err; } return 0; @@ -200,17 +2746,32 @@ static int ice_clear_phy_tstamp_e810(struct ice_hw *hw, u8 lport, u8 idx) */ int ice_ptp_init_phy_e810(struct ice_hw *hw) { - int status; u8 tmr_idx; + int err; tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; - status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_ENA(tmr_idx), - GLTSYN_ENA_TSYN_ENA_M); - if (status) + err = ice_write_phy_reg_e810(hw, ETH_GLTSYN_ENA(tmr_idx), + GLTSYN_ENA_TSYN_ENA_M); + if (err) ice_debug(hw, ICE_DBG_PTP, "PTP failed in ena_phy_time_syn %d\n", - status); + err); - return status; + return err; +} + +/** + * ice_ptp_init_phc_e810 - Perform E810 specific PHC initialization + * @hw: pointer to HW struct + * + * Perform E810-specific PTP hardware clock initialization steps. + */ +static int ice_ptp_init_phc_e810(struct ice_hw *hw) +{ + /* Ensure synchronization delay is zero */ + wr32(hw, GLTSYN_SYNC_DLAY, 0); + + /* Initialize the PHY */ + return ice_ptp_init_phy_e810(hw); } /** @@ -227,22 +2788,22 @@ int ice_ptp_init_phy_e810(struct ice_hw *hw) */ static int ice_ptp_prep_phy_time_e810(struct ice_hw *hw, u32 time) { - int status; u8 tmr_idx; + int err; tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; - status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHTIME_0(tmr_idx), 0); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to write SHTIME_0, status %d\n", - status); - return status; + err = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHTIME_0(tmr_idx), 0); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write SHTIME_0, err %d\n", + err); + return err; } - status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHTIME_L(tmr_idx), time); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to write SHTIME_L, status %d\n", - status); - return status; + err = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHTIME_L(tmr_idx), time); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write SHTIME_L, err %d\n", + err); + return err; } return 0; @@ -263,26 +2824,26 @@ static int ice_ptp_prep_phy_time_e810(struct ice_hw *hw, u32 time) */ static int ice_ptp_prep_phy_adj_e810(struct ice_hw *hw, s32 adj) { - int status; u8 tmr_idx; + int err; tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; /* Adjustments are represented as signed 2's complement values in * nanoseconds. Sub-nanosecond adjustment is not supported. */ - status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_L(tmr_idx), 0); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to write adj to PHY SHADJ_L, status %d\n", - status); - return status; + err = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_L(tmr_idx), 0); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write adj to PHY SHADJ_L, err %d\n", + err); + return err; } - status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_H(tmr_idx), adj); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to write adj to PHY SHADJ_H, status %d\n", - status); - return status; + err = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_H(tmr_idx), adj); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write adj to PHY SHADJ_H, err %d\n", + err); + return err; } return 0; @@ -300,25 +2861,25 @@ static int ice_ptp_prep_phy_adj_e810(struct ice_hw *hw, s32 adj) static int ice_ptp_prep_phy_incval_e810(struct ice_hw *hw, u64 incval) { u32 high, low; - int status; u8 tmr_idx; + int err; tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; low = lower_32_bits(incval); high = upper_32_bits(incval); - status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_L(tmr_idx), low); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to write incval to PHY SHADJ_L, status %d\n", - status); - return status; + err = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_L(tmr_idx), low); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write incval to PHY SHADJ_L, err %d\n", + err); + return err; } - status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_H(tmr_idx), high); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to write incval PHY SHADJ_H, status %d\n", - status); - return status; + err = ice_write_phy_reg_e810(hw, ETH_GLTSYN_SHADJ_H(tmr_idx), high); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write incval PHY SHADJ_H, err %d\n", + err); + return err; } return 0; @@ -335,7 +2896,7 @@ static int ice_ptp_prep_phy_incval_e810(struct ice_hw *hw, u64 incval) static int ice_ptp_port_cmd_e810(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) { u32 cmd_val, val; - int status; + int err; switch (cmd) { case INIT_TIME: @@ -356,20 +2917,20 @@ static int ice_ptp_port_cmd_e810(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) } /* Read, modify, write */ - status = ice_read_phy_reg_e810(hw, ETH_GLTSYN_CMD, &val); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to read GLTSYN_CMD, status %d\n", status); - return status; + err = ice_read_phy_reg_e810(hw, ETH_GLTSYN_CMD, &val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to read GLTSYN_CMD, err %d\n", err); + return err; } /* Modify necessary bits only and perform write */ val &= ~TS_CMD_MASK_E810; val |= cmd_val; - status = ice_write_phy_reg_e810(hw, ETH_GLTSYN_CMD, val); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to write back GLTSYN_CMD, status %d\n", status); - return status; + err = ice_write_phy_reg_e810(hw, ETH_GLTSYN_CMD, val); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to write back GLTSYN_CMD, err %d\n", err); + return err; } return 0; @@ -377,12 +2938,9 @@ static int ice_ptp_port_cmd_e810(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) /* Device agnostic functions * - * The following functions implement useful behavior to hide the differences - * between E810 and other devices. They call the device-specific - * implementations where necessary. - * - * Currently, the driver only supports E810, but future work will enable - * support for E822-based devices. + * The following functions implement shared behavior common to both E822 and + * E810 devices, possibly calling a device specific implementation where + * necessary. */ /** @@ -433,42 +2991,6 @@ void ice_ptp_unlock(struct ice_hw *hw) } /** - * ice_ptp_src_cmd - Prepare source timer for a timer command - * @hw: pointer to HW structure - * @cmd: Timer command - * - * Prepare the source timer for an upcoming timer sync command. - */ -static void ice_ptp_src_cmd(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) -{ - u32 cmd_val; - u8 tmr_idx; - - tmr_idx = ice_get_ptp_src_clock_index(hw); - cmd_val = tmr_idx << SEL_CPK_SRC; - - switch (cmd) { - case INIT_TIME: - cmd_val |= GLTSYN_CMD_INIT_TIME; - break; - case INIT_INCVAL: - cmd_val |= GLTSYN_CMD_INIT_INCVAL; - break; - case ADJ_TIME: - cmd_val |= GLTSYN_CMD_ADJ_TIME; - break; - case ADJ_TIME_AT_TIME: - cmd_val |= GLTSYN_CMD_ADJ_INIT_TIME; - break; - case READ_TIME: - cmd_val |= GLTSYN_CMD_READ_TIME; - break; - } - - wr32(hw, GLTSYN_CMD, cmd_val); -} - -/** * ice_ptp_tmr_cmd - Prepare and trigger a timer sync command * @hw: pointer to HW struct * @cmd: the command to issue @@ -480,23 +3002,26 @@ static void ice_ptp_src_cmd(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) */ static int ice_ptp_tmr_cmd(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) { - int status; + int err; /* First, prepare the source timer */ ice_ptp_src_cmd(hw, cmd); /* Next, prepare the ports */ - status = ice_ptp_port_cmd_e810(hw, cmd); - if (status) { - ice_debug(hw, ICE_DBG_PTP, "Failed to prepare PHY ports for timer command %u, status %d\n", - cmd, status); - return status; + if (ice_is_e810(hw)) + err = ice_ptp_port_cmd_e810(hw, cmd); + else + err = ice_ptp_port_cmd_e822(hw, cmd); + if (err) { + ice_debug(hw, ICE_DBG_PTP, "Failed to prepare PHY ports for timer command %u, err %d\n", + cmd, err); + return err; } - /* Write the sync command register to drive both source and PHY timer commands - * synchronously + /* Write the sync command register to drive both source and PHY timer + * commands synchronously */ - wr32(hw, GLTSYN_CMD_SYNC, SYNC_EXEC_CMD); + ice_ptp_exec_tmr_cmd(hw); return 0; } @@ -516,8 +3041,8 @@ static int ice_ptp_tmr_cmd(struct ice_hw *hw, enum ice_ptp_tmr_cmd cmd) */ int ice_ptp_init_time(struct ice_hw *hw, u64 time) { - int status; u8 tmr_idx; + int err; tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; @@ -528,9 +3053,12 @@ int ice_ptp_init_time(struct ice_hw *hw, u64 time) /* PHY timers */ /* Fill Rx and Tx ports and send msg to PHY */ - status = ice_ptp_prep_phy_time_e810(hw, time & 0xFFFFFFFF); - if (status) - return status; + if (ice_is_e810(hw)) + err = ice_ptp_prep_phy_time_e810(hw, time & 0xFFFFFFFF); + else + err = ice_ptp_prep_phy_time_e822(hw, time & 0xFFFFFFFF); + if (err) + return err; return ice_ptp_tmr_cmd(hw, INIT_TIME); } @@ -551,8 +3079,8 @@ int ice_ptp_init_time(struct ice_hw *hw, u64 time) */ int ice_ptp_write_incval(struct ice_hw *hw, u64 incval) { - int status; u8 tmr_idx; + int err; tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; @@ -560,9 +3088,12 @@ int ice_ptp_write_incval(struct ice_hw *hw, u64 incval) wr32(hw, GLTSYN_SHADJ_L(tmr_idx), lower_32_bits(incval)); wr32(hw, GLTSYN_SHADJ_H(tmr_idx), upper_32_bits(incval)); - status = ice_ptp_prep_phy_incval_e810(hw, incval); - if (status) - return status; + if (ice_is_e810(hw)) + err = ice_ptp_prep_phy_incval_e810(hw, incval); + else + err = ice_ptp_prep_phy_incval_e822(hw, incval); + if (err) + return err; return ice_ptp_tmr_cmd(hw, INIT_INCVAL); } @@ -576,16 +3107,16 @@ int ice_ptp_write_incval(struct ice_hw *hw, u64 incval) */ int ice_ptp_write_incval_locked(struct ice_hw *hw, u64 incval) { - int status; + int err; if (!ice_ptp_lock(hw)) return -EBUSY; - status = ice_ptp_write_incval(hw, incval); + err = ice_ptp_write_incval(hw, incval); ice_ptp_unlock(hw); - return status; + return err; } /** @@ -603,8 +3134,8 @@ int ice_ptp_write_incval_locked(struct ice_hw *hw, u64 incval) */ int ice_ptp_adj_clock(struct ice_hw *hw, s32 adj) { - int status; u8 tmr_idx; + int err; tmr_idx = hw->func_caps.ts_func_info.tmr_index_owned; @@ -616,9 +3147,12 @@ int ice_ptp_adj_clock(struct ice_hw *hw, s32 adj) wr32(hw, GLTSYN_SHADJ_L(tmr_idx), 0); wr32(hw, GLTSYN_SHADJ_H(tmr_idx), adj); - status = ice_ptp_prep_phy_adj_e810(hw, adj); - if (status) - return status; + if (ice_is_e810(hw)) + err = ice_ptp_prep_phy_adj_e810(hw, adj); + else + err = ice_ptp_prep_phy_adj_e822(hw, adj); + if (err) + return err; return ice_ptp_tmr_cmd(hw, ADJ_TIME); } @@ -630,11 +3164,16 @@ int ice_ptp_adj_clock(struct ice_hw *hw, s32 adj) * @idx: the timestamp index to read * @tstamp: on return, the 40bit timestamp value * - * Read a 40bit timestamp value out of the timestamp block. + * Read a 40bit timestamp value out of the timestamp block. For E822 devices, + * the block is the quad to read from. For E810 devices, the block is the + * logical port to read from. */ int ice_read_phy_tstamp(struct ice_hw *hw, u8 block, u8 idx, u64 *tstamp) { - return ice_read_phy_tstamp_e810(hw, block, idx, tstamp); + if (ice_is_e810(hw)) + return ice_read_phy_tstamp_e810(hw, block, idx, tstamp); + else + return ice_read_phy_tstamp_e822(hw, block, idx, tstamp); } /** @@ -643,11 +3182,16 @@ int ice_read_phy_tstamp(struct ice_hw *hw, u8 block, u8 idx, u64 *tstamp) * @block: the block to read from * @idx: the timestamp index to reset * - * Clear a timestamp, resetting its valid bit, from the timestamp block. + * Clear a timestamp, resetting its valid bit, from the timestamp block. For + * E822 devices, the block is the quad to clear from. For E810 devices, the + * block is the logical port to clear from. */ int ice_clear_phy_tstamp(struct ice_hw *hw, u8 block, u8 idx) { - return ice_clear_phy_tstamp_e810(hw, block, idx); + if (ice_is_e810(hw)) + return ice_clear_phy_tstamp_e810(hw, block, idx); + else + return ice_clear_phy_tstamp_e822(hw, block, idx); } /* E810T SMA functions @@ -783,6 +3327,37 @@ int ice_write_sma_ctrl_e810t(struct ice_hw *hw, u8 data) } /** + * ice_read_pca9575_reg_e810t + * @hw: pointer to the hw struct + * @offset: GPIO controller register offset + * @data: pointer to data to be read from the GPIO controller + * + * Read the register from the GPIO controller + */ +int ice_read_pca9575_reg_e810t(struct ice_hw *hw, u8 offset, u8 *data) +{ + struct ice_aqc_link_topo_addr link_topo; + __le16 addr; + u16 handle; + int err; + + memset(&link_topo, 0, sizeof(link_topo)); + + err = ice_get_pca9575_handle(hw, &handle); + if (err) + return err; + + link_topo.handle = cpu_to_le16(handle); + link_topo.topo_params.node_type_ctx = + FIELD_PREP(ICE_AQC_LINK_TOPO_NODE_CTX_M, + ICE_AQC_LINK_TOPO_NODE_CTX_PROVIDED); + + addr = cpu_to_le16((u16)offset); + + return ice_aq_read_i2c(hw, link_topo, 0, addr, 1, data, NULL); +} + +/** * ice_is_pca9575_present * @hw: pointer to the hw struct * @@ -800,3 +3375,25 @@ bool ice_is_pca9575_present(struct ice_hw *hw) return !status && handle; } + +/** + * ice_ptp_init_phc - Initialize PTP hardware clock + * @hw: pointer to the HW struct + * + * Perform the steps required to initialize the PTP hardware clock. + */ +int ice_ptp_init_phc(struct ice_hw *hw) +{ + u8 src_idx = hw->func_caps.ts_func_info.tmr_index_owned; + + /* Enable source clocks */ + wr32(hw, GLTSYN_ENA(src_idx), GLTSYN_ENA_TSYN_ENA_M); + + /* Clear event err indications for auxiliary pins */ + (void)rd32(hw, GLTSYN_STAT(src_idx)); + + if (ice_is_e810(hw)) + return ice_ptp_init_phc_e810(hw); + else + return ice_ptp_init_phc_e822(hw); +} |