diff options
Diffstat (limited to 'drivers/net/phy/broadcom.c')
| -rw-r--r-- | drivers/net/phy/broadcom.c | 107 |
1 files changed, 104 insertions, 3 deletions
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c index bb5104ae4610..ad71c88c87e7 100644 --- a/drivers/net/phy/broadcom.c +++ b/drivers/net/phy/broadcom.c @@ -11,6 +11,7 @@ */ #include "bcm-phy-lib.h" +#include <linux/delay.h> #include <linux/module.h> #include <linux/phy.h> #include <linux/brcmphy.h> @@ -26,6 +27,11 @@ MODULE_DESCRIPTION("Broadcom PHY driver"); MODULE_AUTHOR("Maciej W. Rozycki"); MODULE_LICENSE("GPL"); +struct bcm54xx_phy_priv { + u64 *stats; + struct bcm_ptp_private *ptp; +}; + static int bcm54xx_config_clock_delay(struct phy_device *phydev) { int rc, val; @@ -312,6 +318,22 @@ static void bcm54xx_adjust_rxrefclk(struct phy_device *phydev) bcm_phy_write_shadow(phydev, BCM54XX_SHD_APD, val); } +static void bcm54xx_ptp_stop(struct phy_device *phydev) +{ + struct bcm54xx_phy_priv *priv = phydev->priv; + + if (priv->ptp) + bcm_ptp_stop(priv->ptp); +} + +static void bcm54xx_ptp_config_init(struct phy_device *phydev) +{ + struct bcm54xx_phy_priv *priv = phydev->priv; + + if (priv->ptp) + bcm_ptp_config_init(phydev); +} + static int bcm54xx_config_init(struct phy_device *phydev) { int reg, err, val; @@ -389,6 +411,8 @@ static int bcm54xx_config_init(struct phy_device *phydev) bcm_phy_write_exp(phydev, BCM_EXP_MULTICOLOR, val); } + bcm54xx_ptp_config_init(phydev); + return 0; } @@ -417,6 +441,8 @@ static int bcm54xx_suspend(struct phy_device *phydev) { int ret; + bcm54xx_ptp_stop(phydev); + /* We cannot use a read/modify/write here otherwise the PHY gets into * a bad state where its LEDs keep flashing, thus defeating the purpose * of low power mode. @@ -602,6 +628,26 @@ static int brcm_fet_config_init(struct phy_device *phydev) if (err < 0) return err; + /* The datasheet indicates the PHY needs up to 1us to complete a reset, + * build some slack here. + */ + usleep_range(1000, 2000); + + /* The PHY requires 65 MDC clock cycles to complete a write operation + * and turnaround the line properly. + * + * We ignore -EIO here as the MDIO controller (e.g.: mdio-bcm-unimac) + * may flag the lack of turn-around as a read failure. This is + * particularly true with this combination since the MDIO controller + * only used 64 MDC cycles. This is not a critical failure in this + * specific case and it has no functional impact otherwise, so we let + * that one go through. If there is a genuine bus error, the next read + * of MII_BRCM_FET_INTREG will error out. + */ + err = phy_read(phydev, MII_BMCR); + if (err < 0 && err != -EIO) + return err; + reg = phy_read(phydev, MII_BRCM_FET_INTREG); if (reg < 0) return reg; @@ -720,9 +766,40 @@ static irqreturn_t brcm_fet_handle_interrupt(struct phy_device *phydev) return IRQ_HANDLED; } -struct bcm54xx_phy_priv { - u64 *stats; -}; +static int brcm_fet_suspend(struct phy_device *phydev) +{ + int reg, err, err2, brcmtest; + + /* We cannot use a read/modify/write here otherwise the PHY continues + * to drive LEDs which defeats the purpose of low power mode. + */ + err = phy_write(phydev, MII_BMCR, BMCR_PDOWN); + if (err < 0) + return err; + + /* Enable shadow register access */ + brcmtest = phy_read(phydev, MII_BRCM_FET_BRCMTEST); + if (brcmtest < 0) + return brcmtest; + + reg = brcmtest | MII_BRCM_FET_BT_SRE; + + err = phy_write(phydev, MII_BRCM_FET_BRCMTEST, reg); + if (err < 0) + return err; + + /* Set standby mode */ + err = phy_modify(phydev, MII_BRCM_FET_SHDW_AUXMODE4, + MII_BRCM_FET_SHDW_AM4_STANDBY, + MII_BRCM_FET_SHDW_AM4_STANDBY); + + /* Disable shadow register access */ + err2 = phy_write(phydev, MII_BRCM_FET_BRCMTEST, brcmtest); + if (!err) + err = err2; + + return err; +} static int bcm54xx_phy_probe(struct phy_device *phydev) { @@ -740,6 +817,10 @@ static int bcm54xx_phy_probe(struct phy_device *phydev) if (!priv->stats) return -ENOMEM; + priv->ptp = bcm_ptp_probe(phydev); + if (IS_ERR(priv->ptp)) + return PTR_ERR(priv->ptp); + return 0; } @@ -854,6 +935,7 @@ static struct phy_driver broadcom_drivers[] = { .phy_id_mask = 0xfffffff0, .name = "Broadcom BCM54616S", /* PHY_GBIT_FEATURES */ + .soft_reset = genphy_soft_reset, .config_init = bcm54xx_config_init, .config_aneg = bcm54616s_config_aneg, .config_intr = bcm_phy_config_intr, @@ -986,6 +1068,8 @@ static struct phy_driver broadcom_drivers[] = { .config_init = brcm_fet_config_init, .config_intr = brcm_fet_config_intr, .handle_interrupt = brcm_fet_handle_interrupt, + .suspend = brcm_fet_suspend, + .resume = brcm_fet_config_init, }, { .phy_id = PHY_ID_BCM5241, .phy_id_mask = 0xfffffff0, @@ -994,6 +1078,8 @@ static struct phy_driver broadcom_drivers[] = { .config_init = brcm_fet_config_init, .config_intr = brcm_fet_config_intr, .handle_interrupt = brcm_fet_handle_interrupt, + .suspend = brcm_fet_suspend, + .resume = brcm_fet_config_init, }, { .phy_id = PHY_ID_BCM5395, .phy_id_mask = 0xfffffff0, @@ -1020,6 +1106,20 @@ static struct phy_driver broadcom_drivers[] = { .handle_interrupt = bcm_phy_handle_interrupt, .link_change_notify = bcm54xx_link_change_notify, }, { + .phy_id = PHY_ID_BCM53128, + .phy_id_mask = 0xfffffff0, + .name = "Broadcom BCM53128", + .flags = PHY_IS_INTERNAL, + /* PHY_GBIT_FEATURES */ + .get_sset_count = bcm_phy_get_sset_count, + .get_strings = bcm_phy_get_strings, + .get_stats = bcm54xx_get_stats, + .probe = bcm54xx_phy_probe, + .config_init = bcm54xx_config_init, + .config_intr = bcm_phy_config_intr, + .handle_interrupt = bcm_phy_handle_interrupt, + .link_change_notify = bcm54xx_link_change_notify, +}, { .phy_id = PHY_ID_BCM89610, .phy_id_mask = 0xfffffff0, .name = "Broadcom BCM89610", @@ -1055,6 +1155,7 @@ static struct mdio_device_id __maybe_unused broadcom_tbl[] = { { PHY_ID_BCM5241, 0xfffffff0 }, { PHY_ID_BCM5395, 0xfffffff0 }, { PHY_ID_BCM53125, 0xfffffff0 }, + { PHY_ID_BCM53128, 0xfffffff0 }, { PHY_ID_BCM89610, 0xfffffff0 }, { } }; |