diff options
Diffstat (limited to 'drivers/phy/marvell/phy-mvebu-a3700-comphy.c')
| -rw-r--r-- | drivers/phy/marvell/phy-mvebu-a3700-comphy.c | 1332 |
1 files changed, 1215 insertions, 117 deletions
diff --git a/drivers/phy/marvell/phy-mvebu-a3700-comphy.c b/drivers/phy/marvell/phy-mvebu-a3700-comphy.c index dbb2d4308851..a4d7d9bd100d 100644 --- a/drivers/phy/marvell/phy-mvebu-a3700-comphy.c +++ b/drivers/phy/marvell/phy-mvebu-a3700-comphy.c @@ -5,12 +5,16 @@ * Authors: * Evan Wang <xswang@marvell.com> * Miquèl Raynal <miquel.raynal@bootlin.com> + * Pali Rohár <pali@kernel.org> + * Marek Behún <kabel@kernel.org> * * Structure inspired from phy-mvebu-cp110-comphy.c written by Antoine Tenart. - * SMC call initial support done by Grzegorz Jaszczyk. + * Comphy code from ARM Trusted Firmware ported by Pali Rohár <pali@kernel.org> + * and Marek Behún <kabel@kernel.org>. */ -#include <linux/arm-smccc.h> +#include <linux/bitfield.h> +#include <linux/clk.h> #include <linux/io.h> #include <linux/iopoll.h> #include <linux/mfd/syscon.h> @@ -18,103 +22,1118 @@ #include <linux/phy.h> #include <linux/phy/phy.h> #include <linux/platform_device.h> +#include <linux/spinlock.h> -#define MVEBU_A3700_COMPHY_LANES 3 - -/* COMPHY Fast SMC function identifiers */ -#define COMPHY_SIP_POWER_ON 0x82000001 -#define COMPHY_SIP_POWER_OFF 0x82000002 -#define COMPHY_SIP_PLL_LOCK 0x82000003 - -#define COMPHY_FW_MODE_SATA 0x1 -#define COMPHY_FW_MODE_SGMII 0x2 -#define COMPHY_FW_MODE_2500BASEX 0x3 -#define COMPHY_FW_MODE_USB3H 0x4 -#define COMPHY_FW_MODE_USB3D 0x5 -#define COMPHY_FW_MODE_PCIE 0x6 -#define COMPHY_FW_MODE_USB3 0xa - -#define COMPHY_FW_SPEED_1_25G 0 /* SGMII 1G */ -#define COMPHY_FW_SPEED_2_5G 1 -#define COMPHY_FW_SPEED_3_125G 2 /* 2500BASE-X */ -#define COMPHY_FW_SPEED_5G 3 -#define COMPHY_FW_SPEED_MAX 0x3F - -#define COMPHY_FW_MODE(mode) ((mode) << 12) -#define COMPHY_FW_NET(mode, idx, speed) (COMPHY_FW_MODE(mode) | \ - ((idx) << 8) | \ - ((speed) << 2)) -#define COMPHY_FW_PCIE(mode, speed, width) (COMPHY_FW_NET(mode, 0, speed) | \ - ((width) << 18)) +#define PLL_SET_DELAY_US 600 +#define COMPHY_PLL_SLEEP 1000 +#define COMPHY_PLL_TIMEOUT 150000 + +/* Comphy lane2 indirect access register offset */ +#define COMPHY_LANE2_INDIR_ADDR 0x0 +#define COMPHY_LANE2_INDIR_DATA 0x4 + +/* SATA and USB3 PHY offset compared to SATA PHY */ +#define COMPHY_LANE2_REGS_BASE 0x200 + +/* + * When accessing common PHY lane registers directly, we need to shift by 1, + * since the registers are 16-bit. + */ +#define COMPHY_LANE_REG_DIRECT(reg) (((reg) & 0x7FF) << 1) + +/* COMPHY registers */ +#define COMPHY_POWER_PLL_CTRL 0x01 +#define PU_IVREF_BIT BIT(15) +#define PU_PLL_BIT BIT(14) +#define PU_RX_BIT BIT(13) +#define PU_TX_BIT BIT(12) +#define PU_TX_INTP_BIT BIT(11) +#define PU_DFE_BIT BIT(10) +#define RESET_DTL_RX_BIT BIT(9) +#define PLL_LOCK_BIT BIT(8) +#define REF_FREF_SEL_MASK GENMASK(4, 0) +#define REF_FREF_SEL_SERDES_25MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x1) +#define REF_FREF_SEL_SERDES_40MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x3) +#define REF_FREF_SEL_SERDES_50MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x4) +#define REF_FREF_SEL_PCIE_USB3_25MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x2) +#define REF_FREF_SEL_PCIE_USB3_40MHZ FIELD_PREP(REF_FREF_SEL_MASK, 0x3) +#define COMPHY_MODE_MASK GENMASK(7, 5) +#define COMPHY_MODE_SATA FIELD_PREP(COMPHY_MODE_MASK, 0x0) +#define COMPHY_MODE_PCIE FIELD_PREP(COMPHY_MODE_MASK, 0x3) +#define COMPHY_MODE_SERDES FIELD_PREP(COMPHY_MODE_MASK, 0x4) +#define COMPHY_MODE_USB3 FIELD_PREP(COMPHY_MODE_MASK, 0x5) + +#define COMPHY_KVCO_CAL_CTRL 0x02 +#define USE_MAX_PLL_RATE_BIT BIT(12) +#define SPEED_PLL_MASK GENMASK(7, 2) +#define SPEED_PLL_VALUE_16 FIELD_PREP(SPEED_PLL_MASK, 0x10) + +#define COMPHY_DIG_LOOPBACK_EN 0x23 +#define SEL_DATA_WIDTH_MASK GENMASK(11, 10) +#define DATA_WIDTH_10BIT FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x0) +#define DATA_WIDTH_20BIT FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x1) +#define DATA_WIDTH_40BIT FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x2) +#define PLL_READY_TX_BIT BIT(4) + +#define COMPHY_SYNC_PATTERN 0x24 +#define TXD_INVERT_BIT BIT(10) +#define RXD_INVERT_BIT BIT(11) + +#define COMPHY_SYNC_MASK_GEN 0x25 +#define PHY_GEN_MAX_MASK GENMASK(11, 10) +#define PHY_GEN_MAX_USB3_5G FIELD_PREP(PHY_GEN_MAX_MASK, 0x1) + +#define COMPHY_ISOLATION_CTRL 0x26 +#define PHY_ISOLATE_MODE BIT(15) + +#define COMPHY_GEN2_SET2 0x3e +#define GS2_TX_SSC_AMP_MASK GENMASK(15, 9) +#define GS2_TX_SSC_AMP_4128 FIELD_PREP(GS2_TX_SSC_AMP_MASK, 0x20) +#define GS2_VREG_RXTX_MAS_ISET_MASK GENMASK(8, 7) +#define GS2_VREG_RXTX_MAS_ISET_60U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\ + 0x0) +#define GS2_VREG_RXTX_MAS_ISET_80U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\ + 0x1) +#define GS2_VREG_RXTX_MAS_ISET_100U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\ + 0x2) +#define GS2_VREG_RXTX_MAS_ISET_120U FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\ + 0x3) +#define GS2_RSVD_6_0_MASK GENMASK(6, 0) + +#define COMPHY_GEN3_SET2 0x3f + +#define COMPHY_IDLE_SYNC_EN 0x48 +#define IDLE_SYNC_EN BIT(12) + +#define COMPHY_MISC_CTRL0 0x4F +#define CLK100M_125M_EN BIT(4) +#define TXDCLK_2X_SEL BIT(6) +#define CLK500M_EN BIT(7) +#define PHY_REF_CLK_SEL BIT(10) + +#define COMPHY_SFT_RESET 0x52 +#define SFT_RST BIT(9) +#define SFT_RST_NO_REG BIT(10) + +#define COMPHY_MISC_CTRL1 0x73 +#define SEL_BITS_PCIE_FORCE BIT(15) + +#define COMPHY_GEN2_SET3 0x112 +#define GS3_FFE_CAP_SEL_MASK GENMASK(3, 0) +#define GS3_FFE_CAP_SEL_VALUE FIELD_PREP(GS3_FFE_CAP_SEL_MASK, 0xF) + +/* PIPE registers */ +#define COMPHY_PIPE_LANE_CFG0 0x180 +#define PRD_TXDEEMPH0_MASK BIT(0) +#define PRD_TXMARGIN_MASK GENMASK(3, 1) +#define PRD_TXSWING_MASK BIT(4) +#define CFG_TX_ALIGN_POS_MASK GENMASK(8, 5) + +#define COMPHY_PIPE_LANE_CFG1 0x181 +#define PRD_TXDEEMPH1_MASK BIT(15) +#define USE_MAX_PLL_RATE_EN BIT(9) +#define TX_DET_RX_MODE BIT(6) +#define GEN2_TX_DATA_DLY_MASK GENMASK(4, 3) +#define GEN2_TX_DATA_DLY_DEFT FIELD_PREP(GEN2_TX_DATA_DLY_MASK, 2) +#define TX_ELEC_IDLE_MODE_EN BIT(0) + +#define COMPHY_PIPE_LANE_STAT1 0x183 +#define TXDCLK_PCLK_EN BIT(0) + +#define COMPHY_PIPE_LANE_CFG4 0x188 +#define SPREAD_SPECTRUM_CLK_EN BIT(7) + +#define COMPHY_PIPE_RST_CLK_CTRL 0x1C1 +#define PIPE_SOFT_RESET BIT(0) +#define PIPE_REG_RESET BIT(1) +#define MODE_CORE_CLK_FREQ_SEL BIT(9) +#define MODE_PIPE_WIDTH_32 BIT(3) +#define MODE_REFDIV_MASK GENMASK(5, 4) +#define MODE_REFDIV_BY_4 FIELD_PREP(MODE_REFDIV_MASK, 0x2) + +#define COMPHY_PIPE_TEST_MODE_CTRL 0x1C2 +#define MODE_MARGIN_OVERRIDE BIT(2) + +#define COMPHY_PIPE_CLK_SRC_LO 0x1C3 +#define MODE_CLK_SRC BIT(0) +#define BUNDLE_PERIOD_SEL BIT(1) +#define BUNDLE_PERIOD_SCALE_MASK GENMASK(3, 2) +#define BUNDLE_SAMPLE_CTRL BIT(4) +#define PLL_READY_DLY_MASK GENMASK(7, 5) +#define CFG_SEL_20B BIT(15) + +#define COMPHY_PIPE_PWR_MGM_TIM1 0x1D0 +#define CFG_PM_OSCCLK_WAIT_MASK GENMASK(15, 12) +#define CFG_PM_RXDEN_WAIT_MASK GENMASK(11, 8) +#define CFG_PM_RXDEN_WAIT_1_UNIT FIELD_PREP(CFG_PM_RXDEN_WAIT_MASK, 0x1) +#define CFG_PM_RXDLOZ_WAIT_MASK GENMASK(7, 0) +#define CFG_PM_RXDLOZ_WAIT_7_UNIT FIELD_PREP(CFG_PM_RXDLOZ_WAIT_MASK, 0x7) +#define CFG_PM_RXDLOZ_WAIT_12_UNIT FIELD_PREP(CFG_PM_RXDLOZ_WAIT_MASK, 0xC) + +/* + * This register is not from PHY lane register space. It only exists in the + * indirect register space, before the actual PHY lane 2 registers. So the + * offset is absolute, not relative to COMPHY_LANE2_REGS_BASE. + * It is used only for SATA PHY initialization. + */ +#define COMPHY_RESERVED_REG 0x0E +#define PHYCTRL_FRM_PIN_BIT BIT(13) + +/* South Bridge PHY Configuration Registers */ +#define COMPHY_PHY_REG(lane, reg) (((1 - (lane)) * 0x28) + ((reg) & 0x3f)) + +/* + * lane0: USB3/GbE1 PHY Configuration 1 + * lane1: PCIe/GbE0 PHY Configuration 1 + * (used only by SGMII code) + */ +#define COMPHY_PHY_CFG1 0x0 +#define PIN_PU_IVREF_BIT BIT(1) +#define PIN_RESET_CORE_BIT BIT(11) +#define PIN_RESET_COMPHY_BIT BIT(12) +#define PIN_PU_PLL_BIT BIT(16) +#define PIN_PU_RX_BIT BIT(17) +#define PIN_PU_TX_BIT BIT(18) +#define PIN_TX_IDLE_BIT BIT(19) +#define GEN_RX_SEL_MASK GENMASK(25, 22) +#define GEN_RX_SEL_VALUE(val) FIELD_PREP(GEN_RX_SEL_MASK, (val)) +#define GEN_TX_SEL_MASK GENMASK(29, 26) +#define GEN_TX_SEL_VALUE(val) FIELD_PREP(GEN_TX_SEL_MASK, (val)) +#define SERDES_SPEED_1_25_G 0x6 +#define SERDES_SPEED_3_125_G 0x8 +#define PHY_RX_INIT_BIT BIT(30) + +/* + * lane0: USB3/GbE1 PHY Status 1 + * lane1: PCIe/GbE0 PHY Status 1 + * (used only by SGMII code) + */ +#define COMPHY_PHY_STAT1 0x18 +#define PHY_RX_INIT_DONE_BIT BIT(0) +#define PHY_PLL_READY_RX_BIT BIT(2) +#define PHY_PLL_READY_TX_BIT BIT(3) + +/* PHY Selector */ +#define COMPHY_SELECTOR_PHY_REG 0xFC +/* bit0: 0: Lane1 is GbE0; 1: Lane1 is PCIe */ +#define COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT BIT(0) +/* bit4: 0: Lane0 is GbE1; 1: Lane0 is USB3 */ +#define COMPHY_SELECTOR_USB3_GBE1_SEL_BIT BIT(4) +/* bit8: 0: Lane0 is USB3 instead of GbE1, Lane2 is SATA; 1: Lane2 is USB3 */ +#define COMPHY_SELECTOR_USB3_PHY_SEL_BIT BIT(8) struct mvebu_a3700_comphy_conf { unsigned int lane; enum phy_mode mode; int submode; - u32 fw_mode; }; -#define MVEBU_A3700_COMPHY_CONF(_lane, _mode, _smode, _fw) \ +#define MVEBU_A3700_COMPHY_CONF(_lane, _mode, _smode) \ { \ .lane = _lane, \ .mode = _mode, \ .submode = _smode, \ - .fw_mode = _fw, \ } -#define MVEBU_A3700_COMPHY_CONF_GEN(_lane, _mode, _fw) \ - MVEBU_A3700_COMPHY_CONF(_lane, _mode, PHY_INTERFACE_MODE_NA, _fw) +#define MVEBU_A3700_COMPHY_CONF_GEN(_lane, _mode) \ + MVEBU_A3700_COMPHY_CONF(_lane, _mode, PHY_INTERFACE_MODE_NA) -#define MVEBU_A3700_COMPHY_CONF_ETH(_lane, _smode, _fw) \ - MVEBU_A3700_COMPHY_CONF(_lane, PHY_MODE_ETHERNET, _smode, _fw) +#define MVEBU_A3700_COMPHY_CONF_ETH(_lane, _smode) \ + MVEBU_A3700_COMPHY_CONF(_lane, PHY_MODE_ETHERNET, _smode) static const struct mvebu_a3700_comphy_conf mvebu_a3700_comphy_modes[] = { /* lane 0 */ - MVEBU_A3700_COMPHY_CONF_GEN(0, PHY_MODE_USB_HOST_SS, - COMPHY_FW_MODE_USB3H), - MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_SGMII, - COMPHY_FW_MODE_SGMII), - MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_2500BASEX, - COMPHY_FW_MODE_2500BASEX), + MVEBU_A3700_COMPHY_CONF_GEN(0, PHY_MODE_USB_HOST_SS), + MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_SGMII), + MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_1000BASEX), + MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_2500BASEX), /* lane 1 */ - MVEBU_A3700_COMPHY_CONF_GEN(1, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), - MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_SGMII, - COMPHY_FW_MODE_SGMII), - MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_2500BASEX, - COMPHY_FW_MODE_2500BASEX), + MVEBU_A3700_COMPHY_CONF_GEN(1, PHY_MODE_PCIE), + MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_SGMII), + MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_1000BASEX), + MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_2500BASEX), /* lane 2 */ - MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_SATA, COMPHY_FW_MODE_SATA), - MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_USB_HOST_SS, - COMPHY_FW_MODE_USB3H), + MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_SATA), + MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_USB_HOST_SS), +}; + +struct mvebu_a3700_comphy_priv { + void __iomem *comphy_regs; + void __iomem *lane0_phy_regs; /* USB3 and GbE1 */ + void __iomem *lane1_phy_regs; /* PCIe and GbE0 */ + void __iomem *lane2_phy_indirect; /* SATA and USB3 */ + spinlock_t lock; /* for PHY selector access */ + bool xtal_is_40m; }; struct mvebu_a3700_comphy_lane { + struct mvebu_a3700_comphy_priv *priv; struct device *dev; unsigned int id; enum phy_mode mode; int submode; + bool invert_tx; + bool invert_rx; + bool needs_reset; +}; + +struct gbe_phy_init_data_fix { + u16 addr; + u16 value; +}; + +/* Changes to 40M1G25 mode data required for running 40M3G125 init mode */ +static struct gbe_phy_init_data_fix gbe_phy_init_fix[] = { + { 0x005, 0x07CC }, { 0x015, 0x0000 }, { 0x01B, 0x0000 }, + { 0x01D, 0x0000 }, { 0x01E, 0x0000 }, { 0x01F, 0x0000 }, + { 0x020, 0x0000 }, { 0x021, 0x0030 }, { 0x026, 0x0888 }, + { 0x04D, 0x0152 }, { 0x04F, 0xA020 }, { 0x050, 0x07CC }, + { 0x053, 0xE9CA }, { 0x055, 0xBD97 }, { 0x071, 0x3015 }, + { 0x076, 0x03AA }, { 0x07C, 0x0FDF }, { 0x0C2, 0x3030 }, + { 0x0C3, 0x8000 }, { 0x0E2, 0x5550 }, { 0x0E3, 0x12A4 }, + { 0x0E4, 0x7D00 }, { 0x0E6, 0x0C83 }, { 0x101, 0xFCC0 }, + { 0x104, 0x0C10 } +}; + +/* 40M1G25 mode init data */ +static u16 gbe_phy_init[512] = { + /* 0 1 2 3 4 5 6 7 */ + /*-----------------------------------------------------------*/ + /* 8 9 A B C D E F */ + 0x3110, 0xFD83, 0x6430, 0x412F, 0x82C0, 0x06FA, 0x4500, 0x6D26, /* 00 */ + 0xAFC0, 0x8000, 0xC000, 0x0000, 0x2000, 0x49CC, 0x0BC9, 0x2A52, /* 08 */ + 0x0BD2, 0x0CDE, 0x13D2, 0x0CE8, 0x1149, 0x10E0, 0x0000, 0x0000, /* 10 */ + 0x0000, 0x0000, 0x0000, 0x0001, 0x0000, 0x4134, 0x0D2D, 0xFFFF, /* 18 */ + 0xFFE0, 0x4030, 0x1016, 0x0030, 0x0000, 0x0800, 0x0866, 0x0000, /* 20 */ + 0x0000, 0x0000, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, /* 28 */ + 0xFFFF, 0xFFFF, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* 30 */ + 0x0000, 0x0000, 0x000F, 0x6A62, 0x1988, 0x3100, 0x3100, 0x3100, /* 38 */ + 0x3100, 0xA708, 0x2430, 0x0830, 0x1030, 0x4610, 0xFF00, 0xFF00, /* 40 */ + 0x0060, 0x1000, 0x0400, 0x0040, 0x00F0, 0x0155, 0x1100, 0xA02A, /* 48 */ + 0x06FA, 0x0080, 0xB008, 0xE3ED, 0x5002, 0xB592, 0x7A80, 0x0001, /* 50 */ + 0x020A, 0x8820, 0x6014, 0x8054, 0xACAA, 0xFC88, 0x2A02, 0x45CF, /* 58 */ + 0x000F, 0x1817, 0x2860, 0x064F, 0x0000, 0x0204, 0x1800, 0x6000, /* 60 */ + 0x810F, 0x4F23, 0x4000, 0x4498, 0x0850, 0x0000, 0x000E, 0x1002, /* 68 */ + 0x9D3A, 0x3009, 0xD066, 0x0491, 0x0001, 0x6AB0, 0x0399, 0x3780, /* 70 */ + 0x0040, 0x5AC0, 0x4A80, 0x0000, 0x01DF, 0x0000, 0x0007, 0x0000, /* 78 */ + 0x2D54, 0x00A1, 0x4000, 0x0100, 0xA20A, 0x0000, 0x0000, 0x0000, /* 80 */ + 0x0000, 0x0000, 0x0000, 0x7400, 0x0E81, 0x1000, 0x1242, 0x0210, /* 88 */ + 0x80DF, 0x0F1F, 0x2F3F, 0x4F5F, 0x6F7F, 0x0F1F, 0x2F3F, 0x4F5F, /* 90 */ + 0x6F7F, 0x4BAD, 0x0000, 0x0000, 0x0800, 0x0000, 0x2400, 0xB651, /* 98 */ + 0xC9E0, 0x4247, 0x0A24, 0x0000, 0xAF19, 0x1004, 0x0000, 0x0000, /* A0 */ + 0x0000, 0x0013, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* A8 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* B0 */ + 0x0000, 0x0000, 0x0000, 0x0060, 0x0000, 0x0000, 0x0000, 0x0000, /* B8 */ + 0x0000, 0x0000, 0x3010, 0xFA00, 0x0000, 0x0000, 0x0000, 0x0003, /* C0 */ + 0x1618, 0x8200, 0x8000, 0x0400, 0x050F, 0x0000, 0x0000, 0x0000, /* C8 */ + 0x4C93, 0x0000, 0x1000, 0x1120, 0x0010, 0x1242, 0x1242, 0x1E00, /* D0 */ + 0x0000, 0x0000, 0x0000, 0x00F8, 0x0000, 0x0041, 0x0800, 0x0000, /* D8 */ + 0x82A0, 0x572E, 0x2490, 0x14A9, 0x4E00, 0x0000, 0x0803, 0x0541, /* E0 */ + 0x0C15, 0x0000, 0x0000, 0x0400, 0x2626, 0x0000, 0x0000, 0x4200, /* E8 */ + 0x0000, 0xAA55, 0x1020, 0x0000, 0x0000, 0x5010, 0x0000, 0x0000, /* F0 */ + 0x0000, 0x0000, 0x5000, 0x0000, 0x0000, 0x0000, 0x02F2, 0x0000, /* F8 */ + 0x101F, 0xFDC0, 0x4000, 0x8010, 0x0110, 0x0006, 0x0000, 0x0000, /*100 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*108 */ + 0x04CF, 0x0000, 0x04CF, 0x0000, 0x04CF, 0x0000, 0x04C6, 0x0000, /*110 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*118 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*120 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*128 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*130 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*138 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*140 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*148 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*150 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*158 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*160 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*168 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*170 */ + 0x0000, 0x0000, 0x0000, 0x00F0, 0x08A2, 0x3112, 0x0A14, 0x0000, /*178 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*180 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*188 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*190 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*198 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1A0 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1A8 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1B0 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1B8 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1C0 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1C8 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1D0 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1D8 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1E0 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1E8 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1F0 */ + 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 /*1F8 */ }; -static int mvebu_a3700_comphy_smc(unsigned long function, unsigned long lane, - unsigned long mode) +static inline void comphy_reg_set(void __iomem *addr, u32 data, u32 mask) { - struct arm_smccc_res res; - s32 ret; + u32 val; - arm_smccc_smc(function, lane, mode, 0, 0, 0, 0, 0, &res); - ret = res.a0; + val = readl(addr); + val = (val & ~mask) | (data & mask); + writel(val, addr); +} + +static inline void comphy_reg_set16(void __iomem *addr, u16 data, u16 mask) +{ + u16 val; + + val = readw(addr); + val = (val & ~mask) | (data & mask); + writew(val, addr); +} + +/* Used for accessing lane 2 registers (SATA/USB3 PHY) */ +static void comphy_set_indirect(struct mvebu_a3700_comphy_priv *priv, + u32 offset, u16 data, u16 mask) +{ + writel(offset, + priv->lane2_phy_indirect + COMPHY_LANE2_INDIR_ADDR); + comphy_reg_set(priv->lane2_phy_indirect + COMPHY_LANE2_INDIR_DATA, + data, mask); +} + +static void comphy_lane_reg_set(struct mvebu_a3700_comphy_lane *lane, + u16 reg, u16 data, u16 mask) +{ + if (lane->id == 2) { + /* lane 2 PHY registers are accessed indirectly */ + comphy_set_indirect(lane->priv, + reg + COMPHY_LANE2_REGS_BASE, + data, mask); + } else { + void __iomem *base = lane->id == 1 ? + lane->priv->lane1_phy_regs : + lane->priv->lane0_phy_regs; + + comphy_reg_set16(base + COMPHY_LANE_REG_DIRECT(reg), + data, mask); + } +} + +static int comphy_lane_reg_poll(struct mvebu_a3700_comphy_lane *lane, + u16 reg, u16 bits, + ulong sleep_us, ulong timeout_us) +{ + int ret; + + if (lane->id == 2) { + u32 data; + + /* lane 2 PHY registers are accessed indirectly */ + writel(reg + COMPHY_LANE2_REGS_BASE, + lane->priv->lane2_phy_indirect + + COMPHY_LANE2_INDIR_ADDR); + + ret = readl_poll_timeout(lane->priv->lane2_phy_indirect + + COMPHY_LANE2_INDIR_DATA, + data, (data & bits) == bits, + sleep_us, timeout_us); + } else { + void __iomem *base = lane->id == 1 ? + lane->priv->lane1_phy_regs : + lane->priv->lane0_phy_regs; + u16 data; + + ret = readw_poll_timeout(base + COMPHY_LANE_REG_DIRECT(reg), + data, (data & bits) == bits, + sleep_us, timeout_us); + } + + return ret; +} + +static void comphy_periph_reg_set(struct mvebu_a3700_comphy_lane *lane, + u8 reg, u32 data, u32 mask) +{ + comphy_reg_set(lane->priv->comphy_regs + COMPHY_PHY_REG(lane->id, reg), + data, mask); +} + +static int comphy_periph_reg_poll(struct mvebu_a3700_comphy_lane *lane, + u8 reg, u32 bits, + ulong sleep_us, ulong timeout_us) +{ + u32 data; + + return readl_poll_timeout(lane->priv->comphy_regs + + COMPHY_PHY_REG(lane->id, reg), + data, (data & bits) == bits, + sleep_us, timeout_us); +} + +/* PHY selector configures with corresponding modes */ +static int +mvebu_a3700_comphy_set_phy_selector(struct mvebu_a3700_comphy_lane *lane) +{ + u32 old, new, clr = 0, set = 0; + unsigned long flags; + + switch (lane->mode) { + case PHY_MODE_SATA: + /* SATA must be in Lane2 */ + if (lane->id == 2) + clr = COMPHY_SELECTOR_USB3_PHY_SEL_BIT; + else + goto error; + break; + + case PHY_MODE_ETHERNET: + if (lane->id == 0) + clr = COMPHY_SELECTOR_USB3_GBE1_SEL_BIT; + else if (lane->id == 1) + clr = COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT; + else + goto error; + break; + + case PHY_MODE_USB_HOST_SS: + if (lane->id == 2) + set = COMPHY_SELECTOR_USB3_PHY_SEL_BIT; + else if (lane->id == 0) + set = COMPHY_SELECTOR_USB3_GBE1_SEL_BIT; + else + goto error; + break; + + case PHY_MODE_PCIE: + /* PCIE must be in Lane1 */ + if (lane->id == 1) + set = COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT; + else + goto error; + break; - switch (ret) { - case SMCCC_RET_SUCCESS: - return 0; - case SMCCC_RET_NOT_SUPPORTED: - return -EOPNOTSUPP; default: + goto error; + } + + spin_lock_irqsave(&lane->priv->lock, flags); + + old = readl(lane->priv->comphy_regs + COMPHY_SELECTOR_PHY_REG); + new = (old & ~clr) | set; + writel(new, lane->priv->comphy_regs + COMPHY_SELECTOR_PHY_REG); + + spin_unlock_irqrestore(&lane->priv->lock, flags); + + dev_dbg(lane->dev, + "COMPHY[%d] mode[%d] changed PHY selector 0x%08x -> 0x%08x\n", + lane->id, lane->mode, old, new); + + return 0; +error: + dev_err(lane->dev, "COMPHY[%d] mode[%d] is invalid\n", lane->id, + lane->mode); + return -EINVAL; +} + +static int +mvebu_a3700_comphy_sata_power_on(struct mvebu_a3700_comphy_lane *lane) +{ + u32 mask, data, ref_clk; + int ret; + + /* Configure phy selector for SATA */ + ret = mvebu_a3700_comphy_set_phy_selector(lane); + if (ret) + return ret; + + /* Clear phy isolation mode to make it work in normal mode */ + comphy_lane_reg_set(lane, COMPHY_ISOLATION_CTRL, + 0x0, PHY_ISOLATE_MODE); + + /* 0. Check the Polarity invert bits */ + data = 0x0; + if (lane->invert_tx) + data |= TXD_INVERT_BIT; + if (lane->invert_rx) + data |= RXD_INVERT_BIT; + mask = TXD_INVERT_BIT | RXD_INVERT_BIT; + comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask); + + /* 1. Select 40-bit data width */ + comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN, + DATA_WIDTH_40BIT, SEL_DATA_WIDTH_MASK); + + /* 2. Select reference clock(25M) and PHY mode (SATA) */ + if (lane->priv->xtal_is_40m) + ref_clk = REF_FREF_SEL_SERDES_40MHZ; + else + ref_clk = REF_FREF_SEL_SERDES_25MHZ; + + data = ref_clk | COMPHY_MODE_SATA; + mask = REF_FREF_SEL_MASK | COMPHY_MODE_MASK; + comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask); + + /* 3. Use maximum PLL rate (no power save) */ + comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL, + USE_MAX_PLL_RATE_BIT, USE_MAX_PLL_RATE_BIT); + + /* 4. Reset reserved bit */ + comphy_set_indirect(lane->priv, COMPHY_RESERVED_REG, + 0x0, PHYCTRL_FRM_PIN_BIT); + + /* 5. Set vendor-specific configuration (It is done in sata driver) */ + /* XXX: in U-Boot below sequence was executed in this place, in Linux + * not. Now it is done only in U-Boot before this comphy + * initialization - tests shows that it works ok, but in case of any + * future problem it is left for reference. + * reg_set(MVEBU_REGS_BASE + 0xe00a0, 0, 0xffffffff); + * reg_set(MVEBU_REGS_BASE + 0xe00a4, BIT(6), BIT(6)); + */ + + /* Wait for > 55 us to allow PLL be enabled */ + udelay(PLL_SET_DELAY_US); + + /* Polling status */ + ret = comphy_lane_reg_poll(lane, COMPHY_DIG_LOOPBACK_EN, + PLL_READY_TX_BIT, COMPHY_PLL_SLEEP, + COMPHY_PLL_TIMEOUT); + if (ret) + dev_err(lane->dev, "Failed to lock SATA PLL\n"); + + return ret; +} + +static void comphy_gbe_phy_init(struct mvebu_a3700_comphy_lane *lane, + bool is_1gbps) +{ + int addr, fix_idx; + u16 val; + + fix_idx = 0; + for (addr = 0; addr < 512; addr++) { + /* + * All PHY register values are defined in full for 3.125Gbps + * SERDES speed. The values required for 1.25 Gbps are almost + * the same and only few registers should be "fixed" in + * comparison to 3.125 Gbps values. These register values are + * stored in "gbe_phy_init_fix" array. + */ + if (!is_1gbps && gbe_phy_init_fix[fix_idx].addr == addr) { + /* Use new value */ + val = gbe_phy_init_fix[fix_idx].value; + if (fix_idx < ARRAY_SIZE(gbe_phy_init_fix)) + fix_idx++; + } else { + val = gbe_phy_init[addr]; + } + + comphy_lane_reg_set(lane, addr, val, 0xFFFF); + } +} + +static int +mvebu_a3700_comphy_ethernet_power_on(struct mvebu_a3700_comphy_lane *lane) +{ + u32 mask, data, speed_sel; + int ret; + + /* Set selector */ + ret = mvebu_a3700_comphy_set_phy_selector(lane); + if (ret) + return ret; + + /* + * 1. Reset PHY by setting PHY input port PIN_RESET=1. + * 2. Set PHY input port PIN_TX_IDLE=1, PIN_PU_IVREF=1 to keep + * PHY TXP/TXN output to idle state during PHY initialization + * 3. Set PHY input port PIN_PU_PLL=0, PIN_PU_RX=0, PIN_PU_TX=0. + */ + data = PIN_PU_IVREF_BIT | PIN_TX_IDLE_BIT | PIN_RESET_COMPHY_BIT; + mask = data | PIN_RESET_CORE_BIT | PIN_PU_PLL_BIT | PIN_PU_RX_BIT | + PIN_PU_TX_BIT | PHY_RX_INIT_BIT; + comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask); + + /* 4. Release reset to the PHY by setting PIN_RESET=0. */ + data = 0x0; + mask = PIN_RESET_COMPHY_BIT; + comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask); + + /* + * 5. Set PIN_PHY_GEN_TX[3:0] and PIN_PHY_GEN_RX[3:0] to decide COMPHY + * bit rate + */ + switch (lane->submode) { + case PHY_INTERFACE_MODE_SGMII: + case PHY_INTERFACE_MODE_1000BASEX: + /* SGMII 1G, SerDes speed 1.25G */ + speed_sel = SERDES_SPEED_1_25_G; + break; + case PHY_INTERFACE_MODE_2500BASEX: + /* 2500Base-X, SerDes speed 3.125G */ + speed_sel = SERDES_SPEED_3_125_G; + break; + default: + /* Other rates are not supported */ + dev_err(lane->dev, + "unsupported phy speed %d on comphy lane%d\n", + lane->submode, lane->id); return -EINVAL; } + data = GEN_RX_SEL_VALUE(speed_sel) | GEN_TX_SEL_VALUE(speed_sel); + mask = GEN_RX_SEL_MASK | GEN_TX_SEL_MASK; + comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask); + + /* + * 6. Wait 10mS for bandgap and reference clocks to stabilize; then + * start SW programming. + */ + mdelay(10); + + /* 7. Program COMPHY register PHY_MODE */ + data = COMPHY_MODE_SERDES; + mask = COMPHY_MODE_MASK; + comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask); + + /* + * 8. Set COMPHY register REFCLK_SEL to select the correct REFCLK + * source + */ + data = 0x0; + mask = PHY_REF_CLK_SEL; + comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, data, mask); + + /* + * 9. Set correct reference clock frequency in COMPHY register + * REF_FREF_SEL. + */ + if (lane->priv->xtal_is_40m) + data = REF_FREF_SEL_SERDES_50MHZ; + else + data = REF_FREF_SEL_SERDES_25MHZ; + + mask = REF_FREF_SEL_MASK; + comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask); + + /* + * 10. Program COMPHY register PHY_GEN_MAX[1:0] + * This step is mentioned in the flow received from verification team. + * However the PHY_GEN_MAX value is only meaningful for other interfaces + * (not SERDES). For instance, it selects SATA speed 1.5/3/6 Gbps or + * PCIe speed 2.5/5 Gbps + */ + + /* + * 11. Program COMPHY register SEL_BITS to set correct parallel data + * bus width + */ + data = DATA_WIDTH_10BIT; + mask = SEL_DATA_WIDTH_MASK; + comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN, data, mask); + + /* + * 12. As long as DFE function needs to be enabled in any mode, + * COMPHY register DFE_UPDATE_EN[5:0] shall be programmed to 0x3F + * for real chip during COMPHY power on. + * The value of the DFE_UPDATE_EN already is 0x3F, because it is the + * default value after reset of the PHY. + */ + + /* + * 13. Program COMPHY GEN registers. + * These registers should be programmed based on the lab testing result + * to achieve optimal performance. Please contact the CEA group to get + * the related GEN table during real chip bring-up. We only required to + * run though the entire registers programming flow defined by + * "comphy_gbe_phy_init" when the REF clock is 40 MHz. For REF clock + * 25 MHz the default values stored in PHY registers are OK. + */ + dev_dbg(lane->dev, "Running C-DPI phy init %s mode\n", + lane->submode == PHY_INTERFACE_MODE_2500BASEX ? "2G5" : "1G"); + if (lane->priv->xtal_is_40m) + comphy_gbe_phy_init(lane, + lane->submode != PHY_INTERFACE_MODE_2500BASEX); + + /* + * 14. Check the PHY Polarity invert bit + */ + data = 0x0; + if (lane->invert_tx) + data |= TXD_INVERT_BIT; + if (lane->invert_rx) + data |= RXD_INVERT_BIT; + mask = TXD_INVERT_BIT | RXD_INVERT_BIT; + comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask); + + /* + * 15. Set PHY input ports PIN_PU_PLL, PIN_PU_TX and PIN_PU_RX to 1 to + * start PHY power up sequence. All the PHY register programming should + * be done before PIN_PU_PLL=1. There should be no register programming + * for normal PHY operation from this point. + */ + data = PIN_PU_PLL_BIT | PIN_PU_RX_BIT | PIN_PU_TX_BIT; + mask = data; + comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask); + + /* + * 16. Wait for PHY power up sequence to finish by checking output ports + * PIN_PLL_READY_TX=1 and PIN_PLL_READY_RX=1. + */ + ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1, + PHY_PLL_READY_TX_BIT | + PHY_PLL_READY_RX_BIT, + COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT); + if (ret) { + dev_err(lane->dev, "Failed to lock PLL for SERDES PHY %d\n", + lane->id); + return ret; + } + + /* + * 17. Set COMPHY input port PIN_TX_IDLE=0 + */ + comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, 0x0, PIN_TX_IDLE_BIT); + + /* + * 18. After valid data appear on PIN_RXDATA bus, set PIN_RX_INIT=1. To + * start RX initialization. PIN_RX_INIT_DONE will be cleared to 0 by the + * PHY After RX initialization is done, PIN_RX_INIT_DONE will be set to + * 1 by COMPHY Set PIN_RX_INIT=0 after PIN_RX_INIT_DONE= 1. Please + * refer to RX initialization part for details. + */ + comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, + PHY_RX_INIT_BIT, PHY_RX_INIT_BIT); + + ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1, + PHY_PLL_READY_TX_BIT | + PHY_PLL_READY_RX_BIT, + COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT); + if (ret) { + dev_err(lane->dev, "Failed to lock PLL for SERDES PHY %d\n", + lane->id); + return ret; + } + + ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1, + PHY_RX_INIT_DONE_BIT, + COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT); + if (ret) + dev_err(lane->dev, "Failed to init RX of SERDES PHY %d\n", + lane->id); + + return ret; +} + +static int +mvebu_a3700_comphy_usb3_power_on(struct mvebu_a3700_comphy_lane *lane) +{ + u32 mask, data, cfg, ref_clk; + int ret; + + /* Set phy seclector */ + ret = mvebu_a3700_comphy_set_phy_selector(lane); + if (ret) + return ret; + + /* + * 0. Set PHY OTG Control(0x5d034), bit 4, Power up OTG module The + * register belong to UTMI module, so it is set in UTMI phy driver. + */ + + /* + * 1. Set PRD_TXDEEMPH (3.5db de-emph) + */ + data = PRD_TXDEEMPH0_MASK; + mask = PRD_TXDEEMPH0_MASK | PRD_TXMARGIN_MASK | PRD_TXSWING_MASK | + CFG_TX_ALIGN_POS_MASK; + comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG0, data, mask); + + /* + * 2. Set BIT0: enable transmitter in high impedance mode + * Set BIT[3:4]: delay 2 clock cycles for HiZ off latency + * Set BIT6: Tx detect Rx at HiZ mode + * Unset BIT15: set to 0 to set USB3 De-emphasize level to -3.5db + * together with bit 0 of COMPHY_PIPE_LANE_CFG0 register + */ + data = TX_DET_RX_MODE | GEN2_TX_DATA_DLY_DEFT | TX_ELEC_IDLE_MODE_EN; + mask = PRD_TXDEEMPH1_MASK | TX_DET_RX_MODE | GEN2_TX_DATA_DLY_MASK | + TX_ELEC_IDLE_MODE_EN; + comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG1, data, mask); + + /* + * 3. Set Spread Spectrum Clock Enabled + */ + comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG4, + SPREAD_SPECTRUM_CLK_EN, SPREAD_SPECTRUM_CLK_EN); + + /* + * 4. Set Override Margining Controls From the MAC: + * Use margining signals from lane configuration + */ + comphy_lane_reg_set(lane, COMPHY_PIPE_TEST_MODE_CTRL, + MODE_MARGIN_OVERRIDE, 0xFFFF); + + /* + * 5. Set Lane-to-Lane Bundle Clock Sampling Period = per PCLK cycles + * set Mode Clock Source = PCLK is generated from REFCLK + */ + data = 0x0; + mask = MODE_CLK_SRC | BUNDLE_PERIOD_SEL | BUNDLE_PERIOD_SCALE_MASK | + BUNDLE_SAMPLE_CTRL | PLL_READY_DLY_MASK; + comphy_lane_reg_set(lane, COMPHY_PIPE_CLK_SRC_LO, data, mask); + + /* + * 6. Set G2 Spread Spectrum Clock Amplitude at 4K + */ + comphy_lane_reg_set(lane, COMPHY_GEN2_SET2, + GS2_TX_SSC_AMP_4128, GS2_TX_SSC_AMP_MASK); + + /* + * 7. Unset G3 Spread Spectrum Clock Amplitude + * set G3 TX and RX Register Master Current Select + */ + data = GS2_VREG_RXTX_MAS_ISET_60U; + mask = GS2_TX_SSC_AMP_MASK | GS2_VREG_RXTX_MAS_ISET_MASK | + GS2_RSVD_6_0_MASK; + comphy_lane_reg_set(lane, COMPHY_GEN3_SET2, data, mask); + + /* + * 8. Check crystal jumper setting and program the Power and PLL Control + * accordingly Change RX wait + */ + if (lane->priv->xtal_is_40m) { + ref_clk = REF_FREF_SEL_PCIE_USB3_40MHZ; + cfg = CFG_PM_RXDLOZ_WAIT_12_UNIT; + } else { + ref_clk = REF_FREF_SEL_PCIE_USB3_25MHZ; + cfg = CFG_PM_RXDLOZ_WAIT_7_UNIT; + } + + data = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT | + PU_TX_INTP_BIT | PU_DFE_BIT | COMPHY_MODE_USB3 | ref_clk; + mask = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT | + PU_TX_INTP_BIT | PU_DFE_BIT | PLL_LOCK_BIT | COMPHY_MODE_MASK | + REF_FREF_SEL_MASK; + comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask); + + data = CFG_PM_RXDEN_WAIT_1_UNIT | cfg; + mask = CFG_PM_OSCCLK_WAIT_MASK | CFG_PM_RXDEN_WAIT_MASK | + CFG_PM_RXDLOZ_WAIT_MASK; + comphy_lane_reg_set(lane, COMPHY_PIPE_PWR_MGM_TIM1, data, mask); + + /* + * 9. Enable idle sync + */ + comphy_lane_reg_set(lane, COMPHY_IDLE_SYNC_EN, + IDLE_SYNC_EN, IDLE_SYNC_EN); + + /* + * 10. Enable the output of 500M clock + */ + comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, CLK500M_EN, CLK500M_EN); + + /* + * 11. Set 20-bit data width + */ + comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN, + DATA_WIDTH_20BIT, 0xFFFF); + + /* + * 12. Override Speed_PLL value and use MAC PLL + */ + data = SPEED_PLL_VALUE_16 | USE_MAX_PLL_RATE_BIT; + mask = 0xFFFF; + comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL, data, mask); + + /* + * 13. Check the Polarity invert bit + */ + data = 0x0; + if (lane->invert_tx) + data |= TXD_INVERT_BIT; + if (lane->invert_rx) + data |= RXD_INVERT_BIT; + mask = TXD_INVERT_BIT | RXD_INVERT_BIT; + comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask); + + /* + * 14. Set max speed generation to USB3.0 5Gbps + */ + comphy_lane_reg_set(lane, COMPHY_SYNC_MASK_GEN, + PHY_GEN_MAX_USB3_5G, PHY_GEN_MAX_MASK); + + /* + * 15. Set capacitor value for FFE gain peaking to 0xF + */ + comphy_lane_reg_set(lane, COMPHY_GEN2_SET3, + GS3_FFE_CAP_SEL_VALUE, GS3_FFE_CAP_SEL_MASK); + + /* + * 16. Release SW reset + */ + data = MODE_CORE_CLK_FREQ_SEL | MODE_PIPE_WIDTH_32 | MODE_REFDIV_BY_4; + mask = 0xFFFF; + comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL, data, mask); + + /* Wait for > 55 us to allow PCLK be enabled */ + udelay(PLL_SET_DELAY_US); + + ret = comphy_lane_reg_poll(lane, COMPHY_PIPE_LANE_STAT1, TXDCLK_PCLK_EN, + COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT); + if (ret) + dev_err(lane->dev, "Failed to lock USB3 PLL\n"); + + return ret; +} + +static int +mvebu_a3700_comphy_pcie_power_on(struct mvebu_a3700_comphy_lane *lane) +{ + u32 mask, data, ref_clk; + int ret; + + /* Configure phy selector for PCIe */ + ret = mvebu_a3700_comphy_set_phy_selector(lane); + if (ret) + return ret; + + /* 1. Enable max PLL. */ + comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG1, + USE_MAX_PLL_RATE_EN, USE_MAX_PLL_RATE_EN); + + /* 2. Select 20 bit SERDES interface. */ + comphy_lane_reg_set(lane, COMPHY_PIPE_CLK_SRC_LO, + CFG_SEL_20B, CFG_SEL_20B); + + /* 3. Force to use reg setting for PCIe mode */ + comphy_lane_reg_set(lane, COMPHY_MISC_CTRL1, + SEL_BITS_PCIE_FORCE, SEL_BITS_PCIE_FORCE); + + /* 4. Change RX wait */ + data = CFG_PM_RXDEN_WAIT_1_UNIT | CFG_PM_RXDLOZ_WAIT_12_UNIT; + mask = CFG_PM_OSCCLK_WAIT_MASK | CFG_PM_RXDEN_WAIT_MASK | + CFG_PM_RXDLOZ_WAIT_MASK; + comphy_lane_reg_set(lane, COMPHY_PIPE_PWR_MGM_TIM1, data, mask); + + /* 5. Enable idle sync */ + comphy_lane_reg_set(lane, COMPHY_IDLE_SYNC_EN, + IDLE_SYNC_EN, IDLE_SYNC_EN); + + /* 6. Enable the output of 100M/125M/500M clock */ + data = CLK500M_EN | TXDCLK_2X_SEL | CLK100M_125M_EN; + mask = data; + comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, data, mask); + + /* + * 7. Enable TX, PCIE global register, 0xd0074814, it is done in + * PCI-E driver + */ + + /* + * 8. Check crystal jumper setting and program the Power and PLL + * Control accordingly + */ + + if (lane->priv->xtal_is_40m) + ref_clk = REF_FREF_SEL_PCIE_USB3_40MHZ; + else + ref_clk = REF_FREF_SEL_PCIE_USB3_25MHZ; + + data = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT | + PU_TX_INTP_BIT | PU_DFE_BIT | COMPHY_MODE_PCIE | ref_clk; + mask = 0xFFFF; + comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask); + + /* 9. Override Speed_PLL value and use MAC PLL */ + comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL, + SPEED_PLL_VALUE_16 | USE_MAX_PLL_RATE_BIT, + 0xFFFF); + + /* 10. Check the Polarity invert bit */ + data = 0x0; + if (lane->invert_tx) + data |= TXD_INVERT_BIT; + if (lane->invert_rx) + data |= RXD_INVERT_BIT; + mask = TXD_INVERT_BIT | RXD_INVERT_BIT; + comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask); + + /* 11. Release SW reset */ + data = MODE_CORE_CLK_FREQ_SEL | MODE_PIPE_WIDTH_32; + mask = data | PIPE_SOFT_RESET | MODE_REFDIV_MASK; + comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL, data, mask); + + /* Wait for > 55 us to allow PCLK be enabled */ + udelay(PLL_SET_DELAY_US); + + ret = comphy_lane_reg_poll(lane, COMPHY_PIPE_LANE_STAT1, TXDCLK_PCLK_EN, + COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT); + if (ret) + dev_err(lane->dev, "Failed to lock PCIE PLL\n"); + + return ret; } -static int mvebu_a3700_comphy_get_fw_mode(int lane, +static void +mvebu_a3700_comphy_sata_power_off(struct mvebu_a3700_comphy_lane *lane) +{ + /* Set phy isolation mode */ + comphy_lane_reg_set(lane, COMPHY_ISOLATION_CTRL, + PHY_ISOLATE_MODE, PHY_ISOLATE_MODE); + + /* Power off PLL, Tx, Rx */ + comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, + 0x0, PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT); +} + +static void +mvebu_a3700_comphy_ethernet_power_off(struct mvebu_a3700_comphy_lane *lane) +{ + u32 mask, data; + + data = PIN_RESET_CORE_BIT | PIN_RESET_COMPHY_BIT | PIN_PU_IVREF_BIT | + PHY_RX_INIT_BIT; + mask = data; + comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask); +} + +static void +mvebu_a3700_comphy_pcie_power_off(struct mvebu_a3700_comphy_lane *lane) +{ + /* Power off PLL, Tx, Rx */ + comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, + 0x0, PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT); +} + +static int mvebu_a3700_comphy_reset(struct phy *phy) +{ + struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy); + u16 mask, data; + + dev_dbg(lane->dev, "resetting lane %d\n", lane->id); + + /* COMPHY reset for internal logic */ + comphy_lane_reg_set(lane, COMPHY_SFT_RESET, + SFT_RST_NO_REG, SFT_RST_NO_REG); + + /* COMPHY register reset (cleared automatically) */ + comphy_lane_reg_set(lane, COMPHY_SFT_RESET, SFT_RST, SFT_RST); + + /* PIPE soft and register reset */ + data = PIPE_SOFT_RESET | PIPE_REG_RESET; + mask = data; + comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL, data, mask); + + /* Release PIPE register reset */ + comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL, + 0x0, PIPE_REG_RESET); + + /* Reset SB configuration register (only for lanes 0 and 1) */ + if (lane->id == 0 || lane->id == 1) { + u32 mask, data; + + data = PIN_RESET_CORE_BIT | PIN_RESET_COMPHY_BIT | + PIN_PU_PLL_BIT | PIN_PU_RX_BIT | PIN_PU_TX_BIT; + mask = data | PIN_PU_IVREF_BIT | PIN_TX_IDLE_BIT; + comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask); + } + + return 0; +} + +static bool mvebu_a3700_comphy_check_mode(int lane, enum phy_mode mode, int submode) { @@ -122,7 +1141,7 @@ static int mvebu_a3700_comphy_get_fw_mode(int lane, /* Unused PHY mux value is 0x0 */ if (mode == PHY_MODE_INVALID) - return -EINVAL; + return false; for (i = 0; i < n; i++) { if (mvebu_a3700_comphy_modes[i].lane == lane && @@ -132,27 +1151,30 @@ static int mvebu_a3700_comphy_get_fw_mode(int lane, } if (i == n) - return -EINVAL; + return false; - return mvebu_a3700_comphy_modes[i].fw_mode; + return true; } static int mvebu_a3700_comphy_set_mode(struct phy *phy, enum phy_mode mode, int submode) { struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy); - int fw_mode; - if (submode == PHY_INTERFACE_MODE_1000BASEX) - submode = PHY_INTERFACE_MODE_SGMII; - - fw_mode = mvebu_a3700_comphy_get_fw_mode(lane->id, mode, - submode); - if (fw_mode < 0) { + if (!mvebu_a3700_comphy_check_mode(lane->id, mode, submode)) { dev_err(lane->dev, "invalid COMPHY mode\n"); - return fw_mode; + return -EINVAL; } + /* Mode cannot be changed while the PHY is powered on */ + if (phy->power_count && + (lane->mode != mode || lane->submode != submode)) + return -EBUSY; + + /* If changing mode, ensure reset is called */ + if (lane->mode != PHY_MODE_INVALID && lane->mode != mode) + lane->needs_reset = true; + /* Just remember the mode, ->power_on() will do the real setup */ lane->mode = mode; lane->submode = submode; @@ -163,76 +1185,77 @@ static int mvebu_a3700_comphy_set_mode(struct phy *phy, enum phy_mode mode, static int mvebu_a3700_comphy_power_on(struct phy *phy) { struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy); - u32 fw_param; - int fw_mode; - int fw_port; int ret; - fw_mode = mvebu_a3700_comphy_get_fw_mode(lane->id, - lane->mode, lane->submode); - if (fw_mode < 0) { + if (!mvebu_a3700_comphy_check_mode(lane->id, lane->mode, + lane->submode)) { dev_err(lane->dev, "invalid COMPHY mode\n"); - return fw_mode; + return -EINVAL; + } + + if (lane->needs_reset) { + ret = mvebu_a3700_comphy_reset(phy); + if (ret) + return ret; + + lane->needs_reset = false; } switch (lane->mode) { case PHY_MODE_USB_HOST_SS: dev_dbg(lane->dev, "set lane %d to USB3 host mode\n", lane->id); - fw_param = COMPHY_FW_MODE(fw_mode); - break; + return mvebu_a3700_comphy_usb3_power_on(lane); case PHY_MODE_SATA: dev_dbg(lane->dev, "set lane %d to SATA mode\n", lane->id); - fw_param = COMPHY_FW_MODE(fw_mode); - break; + return mvebu_a3700_comphy_sata_power_on(lane); case PHY_MODE_ETHERNET: - fw_port = (lane->id == 0) ? 1 : 0; - switch (lane->submode) { - case PHY_INTERFACE_MODE_SGMII: - dev_dbg(lane->dev, "set lane %d to SGMII mode\n", - lane->id); - fw_param = COMPHY_FW_NET(fw_mode, fw_port, - COMPHY_FW_SPEED_1_25G); - break; - case PHY_INTERFACE_MODE_2500BASEX: - dev_dbg(lane->dev, "set lane %d to 2500BASEX mode\n", - lane->id); - fw_param = COMPHY_FW_NET(fw_mode, fw_port, - COMPHY_FW_SPEED_3_125G); - break; - default: - dev_err(lane->dev, "unsupported PHY submode (%d)\n", - lane->submode); - return -ENOTSUPP; - } - break; + dev_dbg(lane->dev, "set lane %d to Ethernet mode\n", lane->id); + return mvebu_a3700_comphy_ethernet_power_on(lane); case PHY_MODE_PCIE: dev_dbg(lane->dev, "set lane %d to PCIe mode\n", lane->id); - fw_param = COMPHY_FW_PCIE(fw_mode, COMPHY_FW_SPEED_5G, - phy->attrs.bus_width); - break; + return mvebu_a3700_comphy_pcie_power_on(lane); default: dev_err(lane->dev, "unsupported PHY mode (%d)\n", lane->mode); - return -ENOTSUPP; + return -EOPNOTSUPP; } - - ret = mvebu_a3700_comphy_smc(COMPHY_SIP_POWER_ON, lane->id, fw_param); - if (ret == -EOPNOTSUPP) - dev_err(lane->dev, - "unsupported SMC call, try updating your firmware\n"); - - return ret; } static int mvebu_a3700_comphy_power_off(struct phy *phy) { struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy); - return mvebu_a3700_comphy_smc(COMPHY_SIP_POWER_OFF, lane->id, 0); + switch (lane->mode) { + case PHY_MODE_USB_HOST_SS: + /* + * The USB3 MAC sets the USB3 PHY to low state, so we do not + * need to power off USB3 PHY again. + */ + break; + + case PHY_MODE_SATA: + mvebu_a3700_comphy_sata_power_off(lane); + break; + + case PHY_MODE_ETHERNET: + mvebu_a3700_comphy_ethernet_power_off(lane); + break; + + case PHY_MODE_PCIE: + mvebu_a3700_comphy_pcie_power_off(lane); + break; + + default: + dev_err(lane->dev, "invalid COMPHY mode\n"); + return -EINVAL; + } + + return 0; } static const struct phy_ops mvebu_a3700_comphy_ops = { .power_on = mvebu_a3700_comphy_power_on, .power_off = mvebu_a3700_comphy_power_off, + .reset = mvebu_a3700_comphy_reset, .set_mode = mvebu_a3700_comphy_set_mode, .owner = THIS_MODULE, }; @@ -256,13 +1279,75 @@ static struct phy *mvebu_a3700_comphy_xlate(struct device *dev, return ERR_PTR(-EINVAL); } + lane->invert_tx = args->args[1] & BIT(0); + lane->invert_rx = args->args[1] & BIT(1); + return phy; } static int mvebu_a3700_comphy_probe(struct platform_device *pdev) { + struct mvebu_a3700_comphy_priv *priv; struct phy_provider *provider; struct device_node *child; + struct resource *res; + struct clk *clk; + int ret; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + spin_lock_init(&priv->lock); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "comphy"); + priv->comphy_regs = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(priv->comphy_regs)) + return PTR_ERR(priv->comphy_regs); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "lane1_pcie_gbe"); + priv->lane1_phy_regs = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(priv->lane1_phy_regs)) + return PTR_ERR(priv->lane1_phy_regs); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "lane0_usb3_gbe"); + priv->lane0_phy_regs = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(priv->lane0_phy_regs)) + return PTR_ERR(priv->lane0_phy_regs); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "lane2_sata_usb3"); + priv->lane2_phy_indirect = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(priv->lane2_phy_indirect)) + return PTR_ERR(priv->lane2_phy_indirect); + + /* + * Driver needs to know if reference xtal clock is 40MHz or 25MHz. + * Old DT bindings do not have xtal clk present. So do not fail here + * and expects that default 25MHz reference clock is used. + */ + clk = clk_get(&pdev->dev, "xtal"); + if (IS_ERR(clk)) { + if (PTR_ERR(clk) == -EPROBE_DEFER) + return -EPROBE_DEFER; + dev_warn(&pdev->dev, "missing 'xtal' clk (%ld)\n", + PTR_ERR(clk)); + } else { + ret = clk_prepare_enable(clk); + if (ret) { + dev_warn(&pdev->dev, "enabling xtal clk failed (%d)\n", + ret); + } else { + if (clk_get_rate(clk) == 40000000) + priv->xtal_is_40m = true; + clk_disable_unprepare(clk); + } + clk_put(clk); + } + + dev_set_drvdata(&pdev->dev, priv); for_each_available_child_of_node(pdev->dev.of_node, child) { struct mvebu_a3700_comphy_lane *lane; @@ -277,7 +1362,7 @@ static int mvebu_a3700_comphy_probe(struct platform_device *pdev) continue; } - if (lane_id >= MVEBU_A3700_COMPHY_LANES) { + if (lane_id >= 3) { dev_err(&pdev->dev, "invalid 'reg' property\n"); continue; } @@ -295,15 +1380,26 @@ static int mvebu_a3700_comphy_probe(struct platform_device *pdev) return PTR_ERR(phy); } + lane->priv = priv; lane->dev = &pdev->dev; lane->mode = PHY_MODE_INVALID; lane->submode = PHY_INTERFACE_MODE_NA; lane->id = lane_id; + lane->invert_tx = false; + lane->invert_rx = false; phy_set_drvdata(phy, lane); + + /* + * To avoid relying on the bootloader/firmware configuration, + * power off all comphys. + */ + mvebu_a3700_comphy_reset(phy); + lane->needs_reset = false; } provider = devm_of_phy_provider_register(&pdev->dev, mvebu_a3700_comphy_xlate); + return PTR_ERR_OR_ZERO(provider); } @@ -323,5 +1419,7 @@ static struct platform_driver mvebu_a3700_comphy_driver = { module_platform_driver(mvebu_a3700_comphy_driver); MODULE_AUTHOR("Miquèl Raynal <miquel.raynal@bootlin.com>"); +MODULE_AUTHOR("Pali Rohár <pali@kernel.org>"); +MODULE_AUTHOR("Marek Behún <kabel@kernel.org>"); MODULE_DESCRIPTION("Common PHY driver for A3700"); MODULE_LICENSE("GPL v2"); |