aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/serial
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/serial')
-rw-r--r--drivers/serial/8250_pci.c412
-rw-r--r--drivers/serial/8250_pnp.c7
-rw-r--r--drivers/serial/Kconfig51
-rw-r--r--drivers/serial/Makefile1
-rw-r--r--drivers/serial/atmel_serial.c9
-rw-r--r--drivers/serial/bfin_5xx.c297
-rw-r--r--drivers/serial/cpm_uart/cpm_uart_core.c28
-rw-r--r--drivers/serial/crisv10.c79
-rw-r--r--drivers/serial/crisv10.h2
-rw-r--r--drivers/serial/icom.c14
-rw-r--r--drivers/serial/jsm/jsm_driver.c9
-rw-r--r--drivers/serial/jsm/jsm_neo.c14
-rw-r--r--drivers/serial/jsm/jsm_tty.c23
-rw-r--r--drivers/serial/mcf.c2
-rw-r--r--drivers/serial/mpc52xx_uart.c40
-rw-r--r--drivers/serial/pmac_zilog.c15
-rw-r--r--drivers/serial/serial_core.c76
-rw-r--r--drivers/serial/ucc_uart.c1
18 files changed, 824 insertions, 256 deletions
diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c
index 533f82025adf..7ddff3f55087 100644
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -306,6 +306,63 @@ static void __devexit pci_plx9050_exit(struct pci_dev *dev)
}
}
+#define NI8420_INT_ENABLE_REG 0x38
+#define NI8420_INT_ENABLE_BIT 0x2000
+
+static void __devexit pci_ni8420_exit(struct pci_dev *dev)
+{
+ void __iomem *p;
+ unsigned long base, len;
+ unsigned int bar = 0;
+
+ if ((pci_resource_flags(dev, bar) & IORESOURCE_MEM) == 0) {
+ moan_device("no memory in bar", dev);
+ return;
+ }
+
+ base = pci_resource_start(dev, bar);
+ len = pci_resource_len(dev, bar);
+ p = ioremap_nocache(base, len);
+ if (p == NULL)
+ return;
+
+ /* Disable the CPU Interrupt */
+ writel(readl(p + NI8420_INT_ENABLE_REG) & ~(NI8420_INT_ENABLE_BIT),
+ p + NI8420_INT_ENABLE_REG);
+ iounmap(p);
+}
+
+
+/* MITE registers */
+#define MITE_IOWBSR1 0xc4
+#define MITE_IOWCR1 0xf4
+#define MITE_LCIMR1 0x08
+#define MITE_LCIMR2 0x10
+
+#define MITE_LCIMR2_CLR_CPU_IE (1 << 30)
+
+static void __devexit pci_ni8430_exit(struct pci_dev *dev)
+{
+ void __iomem *p;
+ unsigned long base, len;
+ unsigned int bar = 0;
+
+ if ((pci_resource_flags(dev, bar) & IORESOURCE_MEM) == 0) {
+ moan_device("no memory in bar", dev);
+ return;
+ }
+
+ base = pci_resource_start(dev, bar);
+ len = pci_resource_len(dev, bar);
+ p = ioremap_nocache(base, len);
+ if (p == NULL)
+ return;
+
+ /* Disable the CPU Interrupt */
+ writel(MITE_LCIMR2_CLR_CPU_IE, p + MITE_LCIMR2);
+ iounmap(p);
+}
+
/* SBS Technologies Inc. PMC-OCTPRO and P-OCTAL cards */
static int
sbs_setup(struct serial_private *priv, const struct pciserial_board *board,
@@ -597,6 +654,108 @@ static int pci_xircom_init(struct pci_dev *dev)
return 0;
}
+static int pci_ni8420_init(struct pci_dev *dev)
+{
+ void __iomem *p;
+ unsigned long base, len;
+ unsigned int bar = 0;
+
+ if ((pci_resource_flags(dev, bar) & IORESOURCE_MEM) == 0) {
+ moan_device("no memory in bar", dev);
+ return 0;
+ }
+
+ base = pci_resource_start(dev, bar);
+ len = pci_resource_len(dev, bar);
+ p = ioremap_nocache(base, len);
+ if (p == NULL)
+ return -ENOMEM;
+
+ /* Enable CPU Interrupt */
+ writel(readl(p + NI8420_INT_ENABLE_REG) | NI8420_INT_ENABLE_BIT,
+ p + NI8420_INT_ENABLE_REG);
+
+ iounmap(p);
+ return 0;
+}
+
+#define MITE_IOWBSR1_WSIZE 0xa
+#define MITE_IOWBSR1_WIN_OFFSET 0x800
+#define MITE_IOWBSR1_WENAB (1 << 7)
+#define MITE_LCIMR1_IO_IE_0 (1 << 24)
+#define MITE_LCIMR2_SET_CPU_IE (1 << 31)
+#define MITE_IOWCR1_RAMSEL_MASK 0xfffffffe
+
+static int pci_ni8430_init(struct pci_dev *dev)
+{
+ void __iomem *p;
+ unsigned long base, len;
+ u32 device_window;
+ unsigned int bar = 0;
+
+ if ((pci_resource_flags(dev, bar) & IORESOURCE_MEM) == 0) {
+ moan_device("no memory in bar", dev);
+ return 0;
+ }
+
+ base = pci_resource_start(dev, bar);
+ len = pci_resource_len(dev, bar);
+ p = ioremap_nocache(base, len);
+ if (p == NULL)
+ return -ENOMEM;
+
+ /* Set device window address and size in BAR0 */
+ device_window = ((base + MITE_IOWBSR1_WIN_OFFSET) & 0xffffff00)
+ | MITE_IOWBSR1_WENAB | MITE_IOWBSR1_WSIZE;
+ writel(device_window, p + MITE_IOWBSR1);
+
+ /* Set window access to go to RAMSEL IO address space */
+ writel((readl(p + MITE_IOWCR1) & MITE_IOWCR1_RAMSEL_MASK),
+ p + MITE_IOWCR1);
+
+ /* Enable IO Bus Interrupt 0 */
+ writel(MITE_LCIMR1_IO_IE_0, p + MITE_LCIMR1);
+
+ /* Enable CPU Interrupt */
+ writel(MITE_LCIMR2_SET_CPU_IE, p + MITE_LCIMR2);
+
+ iounmap(p);
+ return 0;
+}
+
+/* UART Port Control Register */
+#define NI8430_PORTCON 0x0f
+#define NI8430_PORTCON_TXVR_ENABLE (1 << 3)
+
+static int
+pci_ni8430_setup(struct serial_private *priv,
+ const struct pciserial_board *board,
+ struct uart_port *port, int idx)
+{
+ void __iomem *p;
+ unsigned long base, len;
+ unsigned int bar, offset = board->first_offset;
+
+ if (idx >= board->num_ports)
+ return 1;
+
+ bar = FL_GET_BASE(board->flags);
+ offset += idx * board->uart_offset;
+
+ base = pci_resource_start(priv->dev, bar);
+ len = pci_resource_len(priv->dev, bar);
+ p = ioremap_nocache(base, len);
+
+ /* enable the transciever */
+ writeb(readb(p + offset + NI8430_PORTCON) | NI8430_PORTCON_TXVR_ENABLE,
+ p + offset + NI8430_PORTCON);
+
+ iounmap(p);
+
+ return setup_port(priv, port, bar, offset, board->reg_shift);
+}
+
+
static int pci_netmos_init(struct pci_dev *dev)
{
/* subdevice 0x00PS means <P> parallel, <S> serial */
@@ -913,6 +1072,126 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.exit = __devexit_p(pci_ite887x_exit),
},
/*
+ * National Instruments
+ */
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PCI23216,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PCI2328,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PCI2324,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PCI2322,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PCI2324I,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PCI2322I,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PXI8420_23216,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PXI8420_2328,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PXI8420_2324,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PXI8420_2322,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PXI8422_2324,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_DEVICE_ID_NI_PXI8422_2322,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8420_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ni8420_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_NI,
+ .device = PCI_ANY_ID,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ni8430_init,
+ .setup = pci_ni8430_setup,
+ .exit = __devexit_p(pci_ni8430_exit),
+ },
+ /*
* Panacom
*/
{
@@ -1216,6 +1495,7 @@ enum pci_board_num_t {
pbn_b1_2_115200,
pbn_b1_4_115200,
pbn_b1_8_115200,
+ pbn_b1_16_115200,
pbn_b1_1_921600,
pbn_b1_2_921600,
@@ -1225,6 +1505,9 @@ enum pci_board_num_t {
pbn_b1_2_1250000,
pbn_b1_bt_1_115200,
+ pbn_b1_bt_2_115200,
+ pbn_b1_bt_4_115200,
+
pbn_b1_bt_2_921600,
pbn_b1_1_1382400,
@@ -1280,6 +1563,10 @@ enum pci_board_num_t {
pbn_exar_XR17C154,
pbn_exar_XR17C158,
pbn_pasemi_1682M,
+ pbn_ni8430_2,
+ pbn_ni8430_4,
+ pbn_ni8430_8,
+ pbn_ni8430_16,
};
/*
@@ -1487,6 +1774,12 @@ static struct pciserial_board pci_boards[] __devinitdata = {
.base_baud = 115200,
.uart_offset = 8,
},
+ [pbn_b1_16_115200] = {
+ .flags = FL_BASE1,
+ .num_ports = 16,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
[pbn_b1_1_921600] = {
.flags = FL_BASE1,
@@ -1525,6 +1818,18 @@ static struct pciserial_board pci_boards[] __devinitdata = {
.base_baud = 115200,
.uart_offset = 8,
},
+ [pbn_b1_bt_2_115200] = {
+ .flags = FL_BASE1|FL_BASE_BARS,
+ .num_ports = 2,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [pbn_b1_bt_4_115200] = {
+ .flags = FL_BASE1|FL_BASE_BARS,
+ .num_ports = 4,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
[pbn_b1_bt_2_921600] = {
.flags = FL_BASE1|FL_BASE_BARS,
@@ -1850,6 +2155,37 @@ static struct pciserial_board pci_boards[] __devinitdata = {
.num_ports = 1,
.base_baud = 8333333,
},
+ /*
+ * National Instruments 843x
+ */
+ [pbn_ni8430_16] = {
+ .flags = FL_BASE0,
+ .num_ports = 16,
+ .base_baud = 3686400,
+ .uart_offset = 0x10,
+ .first_offset = 0x800,
+ },
+ [pbn_ni8430_8] = {
+ .flags = FL_BASE0,
+ .num_ports = 8,
+ .base_baud = 3686400,
+ .uart_offset = 0x10,
+ .first_offset = 0x800,
+ },
+ [pbn_ni8430_4] = {
+ .flags = FL_BASE0,
+ .num_ports = 4,
+ .base_baud = 3686400,
+ .uart_offset = 0x10,
+ .first_offset = 0x800,
+ },
+ [pbn_ni8430_2] = {
+ .flags = FL_BASE0,
+ .num_ports = 2,
+ .base_baud = 3686400,
+ .uart_offset = 0x10,
+ .first_offset = 0x800,
+ },
};
static const struct pci_device_id softmodem_blacklist[] = {
@@ -3052,6 +3388,82 @@ static struct pci_device_id serial_pci_tbl[] = {
pbn_pasemi_1682M },
/*
+ * National Instruments
+ */
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI23216,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_16_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI2328,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_8_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI2324,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_bt_4_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI2322,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_bt_2_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI2324I,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_bt_4_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI2322I,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_bt_2_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8420_23216,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_16_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8420_2328,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_8_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8420_2324,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_bt_4_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8420_2322,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_bt_2_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8422_2324,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_bt_4_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8422_2322,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_bt_2_115200 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8430_2322,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_2 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI8430_2322,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_2 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8430_2324,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_4 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI8430_2324,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_4 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8430_2328,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_8 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI8430_2328,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_8 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8430_23216,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_16 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI8430_23216,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_16 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8432_2322,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_2 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI8432_2322,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_2 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PXI8432_2324,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_4 },
+ { PCI_VENDOR_ID_NI, PCI_DEVICE_ID_NI_PCI8432_2324,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_ni8430_4 },
+
+ /*
* ADDI-DATA GmbH communication cards <info@addi-data.com>
*/
{ PCI_VENDOR_ID_ADDIDATA,
diff --git a/drivers/serial/8250_pnp.c b/drivers/serial/8250_pnp.c
index bbcfc26a3b6d..d71dfe398940 100644
--- a/drivers/serial/8250_pnp.c
+++ b/drivers/serial/8250_pnp.c
@@ -333,6 +333,10 @@ static const struct pnp_device_id pnp_dev_table[] = {
{ "WACF006", 0 },
{ "WACF007", 0 },
{ "WACF008", 0 },
+ { "WACF009", 0 },
+ { "WACF00A", 0 },
+ { "WACF00B", 0 },
+ { "WACF00C", 0 },
/* Compaq touchscreen */
{ "FPI2002", 0 },
/* Fujitsu Stylistic touchscreens */
@@ -346,8 +350,9 @@ static const struct pnp_device_id pnp_dev_table[] = {
{ "FUJ02B8", 0 },
{ "FUJ02B9", 0 },
{ "FUJ02BC", 0 },
- /* Fujitsu Wacom Tablet PC devices */
+ /* Fujitsu Wacom Tablet PC device */
{ "FUJ02E5", 0 },
+ /* Fujitsu P-series tablet PC device */
{ "FUJ02E6", 0 },
/*
* LG C1 EXPRESS DUAL (C1-PB11A3) touch screen (actually a FUJ02E6 in
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 9be11b0963f2..0328fd4006e5 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -533,6 +533,13 @@ config SERIAL_S3C6400
Serial port support for the Samsung S3C6400 and S3C6410
SoCs
+config SERIAL_MAX3100
+ tristate "MAX3100 support"
+ depends on SPI
+ select SERIAL_CORE
+ help
+ MAX3100 chip support
+
config SERIAL_DZ
bool "DECstation DZ serial driver"
depends on MACH_DECSTATION && 32BIT
@@ -700,7 +707,7 @@ choice
config SERIAL_BFIN_DMA
bool "DMA mode"
- depends on !DMA_UNCACHED_NONE && !KGDB_UART
+ depends on !DMA_UNCACHED_NONE && KGDB_SERIAL_CONSOLE=n
help
This driver works under DMA mode. If this option is selected, the
blackfin simple dma driver is also enabled.
@@ -727,19 +734,19 @@ config BFIN_UART0_CTSRTS
config UART0_CTS_PIN
int "UART0 CTS pin"
- depends on BFIN_UART0_CTSRTS
+ depends on BFIN_UART0_CTSRTS && !BF548
default 23
help
The default pin is GPIO_GP7.
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config UART0_RTS_PIN
int "UART0 RTS pin"
- depends on BFIN_UART0_CTSRTS
+ depends on BFIN_UART0_CTSRTS && !BF548
default 22
help
The default pin is GPIO_GP6.
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config SERIAL_BFIN_UART1
bool "Enable UART1"
@@ -756,21 +763,21 @@ config BFIN_UART1_CTSRTS
config UART1_CTS_PIN
int "UART1 CTS pin"
- depends on BFIN_UART1_CTSRTS && !BF54x
+ depends on BFIN_UART1_CTSRTS && !BF548
default -1
help
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config UART1_RTS_PIN
int "UART1 RTS pin"
- depends on BFIN_UART1_CTSRTS && !BF54x
+ depends on BFIN_UART1_CTSRTS && !BF548
default -1
help
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config SERIAL_BFIN_UART2
bool "Enable UART2"
- depends on SERIAL_BFIN && (BF54x)
+ depends on SERIAL_BFIN && (BF54x || BF538 || BF539)
help
Enable UART2
@@ -783,17 +790,17 @@ config BFIN_UART2_CTSRTS
config UART2_CTS_PIN
int "UART2 CTS pin"
- depends on BFIN_UART2_CTSRTS
+ depends on BFIN_UART2_CTSRTS && !BF548
default -1
help
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config UART2_RTS_PIN
int "UART2 RTS pin"
- depends on BFIN_UART2_CTSRTS
+ depends on BFIN_UART2_CTSRTS && !BF548
default -1
help
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config SERIAL_BFIN_UART3
bool "Enable UART3"
@@ -808,6 +815,20 @@ config BFIN_UART3_CTSRTS
Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
signal.
+config UART3_CTS_PIN
+ int "UART3 CTS pin"
+ depends on BFIN_UART3_CTSRTS && !BF548
+ default -1
+ help
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
+config UART3_RTS_PIN
+ int "UART3 RTS pin"
+ depends on BFIN_UART3_CTSRTS && !BF548
+ default -1
+ help
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
config SERIAL_IMX
bool "IMX serial port support"
depends on ARM && (ARCH_IMX || ARCH_MXC)
@@ -1374,7 +1395,7 @@ config SERIAL_BFIN_SPORT
depends on BLACKFIN && EXPERIMENTAL
select SERIAL_CORE
help
- Enble support SPORT emulate UART on Blackfin series.
+ Enable SPORT emulate UART on Blackfin series.
To compile this driver as a module, choose M here: the
module will be called bfin_sport_uart.
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 8844c0a03929..d438eb2a73de 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -43,6 +43,7 @@ obj-$(CONFIG_SERIAL_S3C2412) += s3c2412.o
obj-$(CONFIG_SERIAL_S3C2440) += s3c2440.o
obj-$(CONFIG_SERIAL_S3C24A0) += s3c24a0.o
obj-$(CONFIG_SERIAL_S3C6400) += s3c6400.o
+obj-$(CONFIG_SERIAL_MAX3100) += max3100.o
obj-$(CONFIG_SERIAL_IP22_ZILOG) += ip22zilog.o
obj-$(CONFIG_SERIAL_MUX) += mux.o
obj-$(CONFIG_SERIAL_68328) += 68328serial.o
diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c
index 8f58f7ff0dd7..b3497d7e5354 100644
--- a/drivers/serial/atmel_serial.c
+++ b/drivers/serial/atmel_serial.c
@@ -1020,7 +1020,8 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
/* Get current mode register */
mode = UART_GET_MR(port) & ~(ATMEL_US_USCLKS | ATMEL_US_CHRL
- | ATMEL_US_NBSTOP | ATMEL_US_PAR);
+ | ATMEL_US_NBSTOP | ATMEL_US_PAR
+ | ATMEL_US_USMODE);
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
quot = uart_get_divisor(port, baud);
@@ -1065,6 +1066,12 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
} else
mode |= ATMEL_US_PAR_NONE;
+ /* hardware handshake (RTS/CTS) */
+ if (termios->c_cflag & CRTSCTS)
+ mode |= ATMEL_US_USMODE_HWHS;
+ else
+ mode |= ATMEL_US_USMODE_NORMAL;
+
spin_lock_irqsave(&port->lock, flags);
port->read_status_mask = ATMEL_US_OVRE;
diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 318d69dce8e1..18ba812a4f84 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -63,7 +63,6 @@ static int kgdboc_break_enabled;
#define DMA_RX_YCOUNT (PAGE_SIZE / DMA_RX_XCOUNT)
#define DMA_RX_FLUSH_JIFFIES (HZ / 50)
-#define CTS_CHECK_JIFFIES (HZ / 50)
#ifdef CONFIG_SERIAL_BFIN_DMA
static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
@@ -71,10 +70,65 @@ static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
#endif
-static void bfin_serial_mctrl_check(struct bfin_serial_port *uart);
-
static void bfin_serial_reset_irda(struct uart_port *port);
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->cts_pin < 0)
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+
+ /* CTS PIN is negative assertive. */
+ if (UART_GET_CTS(uart))
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+ else
+ return TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->rts_pin < 0)
+ return;
+
+ /* RTS PIN is negative assertive. */
+ if (mctrl & TIOCM_RTS)
+ UART_ENABLE_RTS(uart);
+ else
+ UART_DISABLE_RTS(uart);
+}
+
+/*
+ * Handle any change of modem status signal.
+ */
+static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
+{
+ struct bfin_serial_port *uart = dev_id;
+ unsigned int status;
+
+ status = bfin_serial_get_mctrl(&uart->port);
+ uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ uart->scts = 1;
+ UART_CLEAR_SCTS(uart);
+ UART_CLEAR_IER(uart, EDSSI);
+#endif
+
+ return IRQ_HANDLED;
+}
+#else
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+#endif
+
/*
* interrupts are disabled on entry
*/
@@ -111,6 +165,13 @@ static void bfin_serial_start_tx(struct uart_port *port)
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
struct tty_struct *tty = uart->port.info->port.tty;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
+
/*
* To avoid losting RX interrupt, we reset IR function
* before sending data.
@@ -174,10 +235,10 @@ static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
return;
}
- if (!uart->port.info || !uart->port.info->tty)
+ if (!uart->port.info || !uart->port.info->port.tty)
return;
#endif
- tty = uart->port.info->tty;
+ tty = uart->port.info->port.tty;
if (ANOMALY_05000363) {
/* The BF533 (and BF561) family of processors have a nice anomaly
@@ -264,12 +325,6 @@ static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
{
struct circ_buf *xmit = &uart->port.info->xmit;
- /*
- * Check the modem control lines before
- * transmitting anything.
- */
- bfin_serial_mctrl_check(uart);
-
if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
#ifdef CONFIG_BF54x
/* Clear TFI bit */
@@ -312,6 +367,12 @@ static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id)
{
struct bfin_serial_port *uart = dev_id;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
spin_lock(&uart->port.lock);
if (UART_GET_LSR(uart) & THRE)
bfin_serial_tx_chars(uart);
@@ -328,12 +389,6 @@ static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
uart->tx_done = 0;
- /*
- * Check the modem control lines before
- * transmitting anything.
- */
- bfin_serial_mctrl_check(uart);
-
if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
uart->tx_count = 0;
uart->tx_done = 1;
@@ -401,9 +456,11 @@ static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
else
flg = TTY_NORMAL;
- for (i = uart->rx_dma_buf.tail; i != uart->rx_dma_buf.head; i++) {
+ for (i = uart->rx_dma_buf.tail; ; i++) {
if (i >= UART_XMIT_SIZE)
i = 0;
+ if (i == uart->rx_dma_buf.head)
+ break;
if (!uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
uart_insert_char(&uart->port, status, OE,
uart->rx_dma_buf.buf[i], flg);
@@ -415,7 +472,8 @@ static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
{
- int x_pos, pos, flags;
+ int x_pos, pos;
+ unsigned long flags;
spin_lock_irqsave(&uart->port.lock, flags);
@@ -445,6 +503,13 @@ static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
struct bfin_serial_port *uart = dev_id;
struct circ_buf *xmit = &uart->port.info->xmit;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
+
spin_lock(&uart->port.lock);
if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
disable_dma(uart->tx_dma_channel);
@@ -493,61 +558,6 @@ static unsigned int bfin_serial_tx_empty(struct uart_port *port)
return 0;
}
-static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- if (uart->cts_pin < 0)
- return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-
- if (UART_GET_CTS(uart))
- return TIOCM_DSR | TIOCM_CAR;
- else
-#endif
- return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-}
-
-static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- if (uart->rts_pin < 0)
- return;
-
- if (mctrl & TIOCM_RTS)
- UART_CLEAR_RTS(uart);
- else
- UART_SET_RTS(uart);
-#endif
-}
-
-/*
- * Handle any change of modem status signal since we were last called.
- */
-static void bfin_serial_mctrl_check(struct bfin_serial_port *uart)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- unsigned int status;
- struct uart_info *info = uart->port.info;
- struct tty_struct *tty = info->port.tty;
-
- status = bfin_serial_get_mctrl(&uart->port);
- uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
- if (!(status & TIOCM_CTS)) {
- tty->hw_stopped = 1;
- uart->cts_timer.data = (unsigned long)(uart);
- uart->cts_timer.function = (void *)bfin_serial_mctrl_check;
- uart->cts_timer.expires = jiffies + CTS_CHECK_JIFFIES;
- add_timer(&(uart->cts_timer));
- } else {
- tty->hw_stopped = 0;
- }
-#endif
-}
-
-/*
- * Interrupts are always disabled.
- */
static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
@@ -603,7 +613,7 @@ static int bfin_serial_startup(struct uart_port *port)
uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
add_timer(&(uart->rx_dma_timer));
#else
-#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
if (kgdboc_port_line == uart->port.line && kgdboc_break_enabled)
kgdboc_break_enabled = 0;
@@ -658,11 +668,50 @@ static int bfin_serial_startup(struct uart_port *port)
}
}
# endif
-#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
}
# endif
#endif
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ if (uart->cts_pin >= 0) {
+ if (request_irq(gpio_to_irq(uart->cts_pin),
+ bfin_serial_mctrl_cts_int,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
+ IRQF_DISABLED, "BFIN_UART_CTS", uart)) {
+ uart->cts_pin = -1;
+ pr_info("Unable to attach BlackFin UART CTS interrupt.\
+ So, disable it.\n");
+ }
+ }
+ if (uart->rts_pin >= 0) {
+ gpio_request(uart->rts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->rts_pin, 0);
+ }
+#endif
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (request_irq(uart->status_irq,
+ bfin_serial_mctrl_cts_int,
+ IRQF_DISABLED, "BFIN_UART_MODEM_STATUS", uart)) {
+ pr_info("Unable to attach BlackFin UART Modem \
+ Status interrupt.\n");
+ }
+
+ if (uart->cts_pin >= 0) {
+ gpio_request(uart->cts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->cts_pin, 1);
+ }
+ if (uart->rts_pin >= 0) {
+ gpio_request(uart->rts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->rts_pin, 0);
+ }
+
+ /* CTS RTS PINs are negative assertive. */
+ UART_PUT_MCR(uart, ACTS);
+ UART_SET_IER(uart, EDSSI);
+#endif
+
UART_SET_IER(uart, ERBFI);
return 0;
}
@@ -696,6 +745,21 @@ static void bfin_serial_shutdown(struct uart_port *port)
free_irq(uart->port.irq, uart);
free_irq(uart->port.irq+1, uart);
#endif
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ if (uart->cts_pin >= 0)
+ free_irq(gpio_to_irq(uart->cts_pin), uart);
+ if (uart->rts_pin >= 0)
+ gpio_free(uart->rts_pin);
+#endif
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->cts_pin >= 0)
+ gpio_free(uart->cts_pin);
+ if (uart->rts_pin >= 0)
+ gpio_free(uart->rts_pin);
+ if (UART_GET_IER(uart) && EDSSI)
+ free_irq(uart->status_irq, uart);
+#endif
}
static void
@@ -757,7 +821,7 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
}
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
- quot = uart_get_divisor(port, baud);
+ quot = uart_get_divisor(port, baud) - ANOMALY_05000230;
spin_lock_irqsave(&uart->port.lock, flags);
UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
@@ -861,6 +925,20 @@ static void bfin_serial_set_ldisc(struct uart_port *port)
}
}
+static void bfin_serial_reset_irda(struct uart_port *port)
+{
+ int line = port->line;
+ unsigned short val;
+
+ val = UART_GET_GCTL(&bfin_serial_ports[line]);
+ val &= ~(IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ SSYNC();
+ val |= (IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ SSYNC();
+}
+
#ifdef CONFIG_CONSOLE_POLL
static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr)
{
@@ -906,20 +984,6 @@ static int bfin_kgdboc_port_startup(struct uart_port *port)
}
#endif
-static void bfin_serial_reset_irda(struct uart_port *port)
-{
- int line = port->line;
- unsigned short val;
-
- val = UART_GET_GCTL(&bfin_serial_ports[line]);
- val &= ~(IREN | RPOLC);
- UART_PUT_GCTL(&bfin_serial_ports[line], val);
- SSYNC();
- val |= (IREN | RPOLC);
- UART_PUT_GCTL(&bfin_serial_ports[line], val);
- SSYNC();
-}
-
static struct uart_ops bfin_serial_pops = {
.tx_empty = bfin_serial_tx_empty,
.set_mctrl = bfin_serial_set_mctrl,
@@ -949,6 +1013,39 @@ static struct uart_ops bfin_serial_pops = {
#endif
};
+static void __init bfin_serial_hw_init(void)
+{
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ peripheral_request(P_UART0_TX, DRIVER_NAME);
+ peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ peripheral_request(P_UART1_TX, DRIVER_NAME);
+ peripheral_request(P_UART1_RX, DRIVER_NAME);
+
+# if defined(CONFIG_BFIN_UART1_CTSRTS) && defined(CONFIG_BF54x)
+ peripheral_request(P_UART1_RTS, DRIVER_NAME);
+ peripheral_request(P_UART1_CTS, DRIVER_NAME);
+# endif
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART2
+ peripheral_request(P_UART2_TX, DRIVER_NAME);
+ peripheral_request(P_UART2_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART3
+ peripheral_request(P_UART3_TX, DRIVER_NAME);
+ peripheral_request(P_UART3_RX, DRIVER_NAME);
+
+# if defined(CONFIG_BFIN_UART3_CTSRTS) && defined(CONFIG_BF54x)
+ peripheral_request(P_UART3_RTS, DRIVER_NAME);
+ peripheral_request(P_UART3_CTS, DRIVER_NAME);
+# endif
+#endif
+}
+
static void __init bfin_serial_init_ports(void)
{
static int first = 1;
@@ -958,6 +1055,8 @@ static void __init bfin_serial_init_ports(void)
return;
first = 0;
+ bfin_serial_hw_init();
+
for (i = 0; i < nr_active_ports; i++) {
bfin_serial_ports[i].port.uartclk = get_sclk();
bfin_serial_ports[i].port.fifosize = BFIN_UART_TX_FIFO_SIZE;
@@ -970,6 +1069,8 @@ static void __init bfin_serial_init_ports(void)
bfin_serial_resource[i].uart_base_addr;
bfin_serial_ports[i].port.irq =
bfin_serial_resource[i].uart_irq;
+ bfin_serial_ports[i].status_irq =
+ bfin_serial_resource[i].uart_status_irq;
bfin_serial_ports[i].port.flags = UPF_BOOT_AUTOCONF;
#ifdef CONFIG_SERIAL_BFIN_DMA
bfin_serial_ports[i].tx_done = 1;
@@ -980,16 +1081,14 @@ static void __init bfin_serial_init_ports(void)
bfin_serial_resource[i].uart_rx_dma_channel;
init_timer(&(bfin_serial_ports[i].rx_dma_timer));
#endif
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- init_timer(&(bfin_serial_ports[i].cts_timer));
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
bfin_serial_ports[i].cts_pin =
bfin_serial_resource[i].uart_cts_pin;
bfin_serial_ports[i].rts_pin =
bfin_serial_resource[i].uart_rts_pin;
#endif
- bfin_serial_hw_init(&bfin_serial_ports[i]);
}
-
}
#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
@@ -1046,7 +1145,8 @@ bfin_serial_console_setup(struct console *co, char *options)
int baud = 57600;
int bits = 8;
int parity = 'n';
-# ifdef CONFIG_SERIAL_BFIN_CTSRTS
+# if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
int flow = 'r';
# else
int flow = 'n';
@@ -1088,7 +1188,7 @@ static void
bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
{
struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
- int flags = 0;
+ unsigned long flags;
spin_lock_irqsave(&uart->port.lock, flags);
uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
@@ -1243,7 +1343,8 @@ static int bfin_serial_remove(struct platform_device *dev)
continue;
uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
bfin_serial_ports[i].port.dev = NULL;
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
gpio_free(bfin_serial_ports[i].cts_pin);
gpio_free(bfin_serial_ports[i].rts_pin);
#endif
diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c
index bde4b4b0b80f..f8df0681e160 100644
--- a/drivers/serial/cpm_uart/cpm_uart_core.c
+++ b/drivers/serial/cpm_uart/cpm_uart_core.c
@@ -406,6 +406,18 @@ static int cpm_uart_startup(struct uart_port *port)
pr_debug("CPM uart[%d]:startup\n", port->line);
+ /* If the port is not the console, make sure rx is disabled. */
+ if (!(pinfo->flags & FLAG_CONSOLE)) {
+ /* Disable UART rx */
+ if (IS_SMC(pinfo)) {
+ clrbits16(&pinfo->smcp->smc_smcmr, SMCMR_REN);
+ clrbits8(&pinfo->smcp->smc_smcm, SMCM_RX);
+ } else {
+ clrbits32(&pinfo->sccp->scc_gsmrl, SCC_GSMRL_ENR);
+ clrbits16(&pinfo->sccp->scc_sccm, UART_SCCM_RX);
+ }
+ cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX);
+ }
/* Install interrupt handler. */
retval = request_irq(port->irq, cpm_uart_int, 0, "cpm_uart", port);
if (retval)
@@ -420,8 +432,6 @@ static int cpm_uart_startup(struct uart_port *port)
setbits32(&pinfo->sccp->scc_gsmrl, (SCC_GSMRL_ENR | SCC_GSMRL_ENT));
}
- if (!(pinfo->flags & FLAG_CONSOLE))
- cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX);
return 0;
}
@@ -1096,6 +1106,10 @@ static int cpm_uart_init_port(struct device_node *np,
for (i = 0; i < NUM_GPIOS; i++)
pinfo->gpios[i] = of_get_gpio(np, i);
+#ifdef CONFIG_PPC_EARLY_DEBUG_CPM
+ udbg_putc = NULL;
+#endif
+
return cpm_uart_request_port(&pinfo->port);
out_pram:
@@ -1245,10 +1259,6 @@ static int __init cpm_uart_console_setup(struct console *co, char *options)
baud = 9600;
}
-#ifdef CONFIG_PPC_EARLY_DEBUG_CPM
- udbg_putc = NULL;
-#endif
-
if (IS_SMC(pinfo)) {
out_be16(&pinfo->smcup->smc_brkcr, 0);
cpm_line_cr_cmd(pinfo, CPM_CR_STOP_TX);
@@ -1329,13 +1339,13 @@ static int __devinit cpm_uart_probe(struct of_device *ofdev,
dev_set_drvdata(&ofdev->dev, pinfo);
+ /* initialize the device pointer for the port */
+ pinfo->port.dev = &ofdev->dev;
+
ret = cpm_uart_init_port(ofdev->node, pinfo);
if (ret)
return ret;
- /* initialize the device pointer for the port */
- pinfo->port.dev = &ofdev->dev;
-
return uart_add_one_port(&cpm_reg, &pinfo->port);
}
diff --git a/drivers/serial/crisv10.c b/drivers/serial/crisv10.c
index e642c22c80e2..7ba7d70f04d6 100644
--- a/drivers/serial/crisv10.c
+++ b/drivers/serial/crisv10.c
@@ -1391,7 +1391,7 @@ static inline void e100_disable_rx_irq(struct e100_serial *info)
#if defined(CONFIG_ETRAX_RS485)
/* Enable RS-485 mode on selected port. This is UGLY. */
static int
-e100_enable_rs485(struct tty_struct *tty,struct rs485_control *r)
+e100_enable_rs485(struct tty_struct *tty, struct serial_rs485 *r)
{
struct e100_serial * info = (struct e100_serial *)tty->driver_data;
@@ -1409,13 +1409,11 @@ e100_enable_rs485(struct tty_struct *tty,struct rs485_control *r)
CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 1);
#endif
- info->rs485.rts_on_send = 0x01 & r->rts_on_send;
- info->rs485.rts_after_sent = 0x01 & r->rts_after_sent;
+ info->rs485.flags = r->flags;
if (r->delay_rts_before_send >= 1000)
info->rs485.delay_rts_before_send = 1000;
else
info->rs485.delay_rts_before_send = r->delay_rts_before_send;
- info->rs485.enabled = r->enabled;
/* printk("rts: on send = %i, after = %i, enabled = %i",
info->rs485.rts_on_send,
info->rs485.rts_after_sent,
@@ -1430,17 +1428,18 @@ e100_write_rs485(struct tty_struct *tty,
const unsigned char *buf, int count)
{
struct e100_serial * info = (struct e100_serial *)tty->driver_data;
- int old_enabled = info->rs485.enabled;
+ int old_value = (info->rs485.flags) & SER_RS485_ENABLED;
/* rs485 is always implicitly enabled if we're using the ioctl()
- * but it doesn't have to be set in the rs485_control
+ * but it doesn't have to be set in the serial_rs485
* (to be backward compatible with old apps)
* So we store, set and restore it.
*/
- info->rs485.enabled = 1;
+ info->rs485.flags |= SER_RS485_ENABLED;
/* rs_write now deals with RS485 if enabled */
count = rs_write(tty, buf, count);
- info->rs485.enabled = old_enabled;
+ if (!old_value)
+ info->rs485.flags &= ~(SER_RS485_ENABLED);
return count;
}
@@ -1451,7 +1450,7 @@ static void rs485_toggle_rts_timer_function(unsigned long data)
struct e100_serial *info = (struct e100_serial *)data;
fast_timers_rs485[info->line].function = NULL;
- e100_rts(info, info->rs485.rts_after_sent);
+ e100_rts(info, (info->rs485.flags & SER_RS485_RTS_AFTER_SEND));
#if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER)
e100_enable_rx(info);
e100_enable_rx_irq(info);
@@ -1647,7 +1646,7 @@ transmit_chars_dma(struct e100_serial *info)
info->tr_running = 0;
#if defined(CONFIG_ETRAX_RS485) && defined(CONFIG_ETRAX_FAST_TIMER)
- if (info->rs485.enabled) {
+ if (info->rs485.flags & SER_RS485_ENABLED) {
/* Set a short timer to toggle RTS */
start_one_shot_timer(&fast_timers_rs485[info->line],
rs485_toggle_rts_timer_function,
@@ -2577,7 +2576,7 @@ static void handle_ser_tx_interrupt(struct e100_serial *info)
info->icount.tx++;
if (info->xmit.head == info->xmit.tail) {
#if defined(CONFIG_ETRAX_RS485) && defined(CONFIG_ETRAX_FAST_TIMER)
- if (info->rs485.enabled) {
+ if (info->rs485.flags & SER_RS485_ENABLED) {
/* Set a short timer to toggle RTS */
start_one_shot_timer(&fast_timers_rs485[info->line],
rs485_toggle_rts_timer_function,
@@ -3218,7 +3217,7 @@ rs_write(struct tty_struct *tty,
#if defined(CONFIG_ETRAX_RS485)
struct e100_serial *info = (struct e100_serial *)tty->driver_data;
- if (info->rs485.enabled)
+ if (info->rs485.flags & SER_RS485_ENABLED)
{
/* If we are in RS-485 mode, we need to toggle RTS and disable
* the receiver before initiating a DMA transfer
@@ -3228,7 +3227,7 @@ rs_write(struct tty_struct *tty,
fast_timers_rs485[info->line].function = NULL;
del_fast_timer(&fast_timers_rs485[info->line]);
#endif
- e100_rts(info, info->rs485.rts_on_send);
+ e100_rts(info, (info->rs485.flags & SER_RS485_RTS_ON_SEND));
#if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER)
e100_disable_rx(info);
e100_enable_rx_irq(info);
@@ -3242,7 +3241,7 @@ rs_write(struct tty_struct *tty,
count = rs_raw_write(tty, buf, count);
#if defined(CONFIG_ETRAX_RS485)
- if (info->rs485.enabled)
+ if (info->rs485.flags & SER_RS485_ENABLED)
{
unsigned int val;
/* If we are in RS-485 mode the following has to be done:
@@ -3263,7 +3262,7 @@ rs_write(struct tty_struct *tty,
get_lsr_info(info, &val);
}while (!(val & TIOCSER_TEMT));
- e100_rts(info, info->rs485.rts_after_sent);
+ e100_rts(info, (info->rs485.flags & SER_RS485_RTS_AFTER_SEND));
#if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER)
e100_enable_rx(info);
@@ -3678,14 +3677,52 @@ rs_ioctl(struct tty_struct *tty, struct file * file,
#if defined(CONFIG_ETRAX_RS485)
case TIOCSERSETRS485:
{
+ /* In this ioctl we still use the old structure
+ * rs485_control for backward compatibility
+ * (if we use serial_rs485, then old user-level code
+ * wouldn't work anymore...).
+ * The use of this ioctl is deprecated: use TIOCSRS485
+ * instead.*/
struct rs485_control rs485ctrl;
+ struct serial_rs485 rs485data;
+ printk(KERN_DEBUG "The use of this ioctl is deprecated. Use TIOCSRS485 instead\n");
if (copy_from_user(&rs485ctrl, (struct rs485_control *)arg,
sizeof(rs485ctrl)))
return -EFAULT;
- return e100_enable_rs485(tty, &rs485ctrl);
+ rs485data.delay_rts_before_send = rs485ctrl.delay_rts_before_send;
+ rs485data.flags = 0;
+ if (rs485ctrl.enabled)
+ rs485data.flags |= SER_RS485_ENABLED;
+ else
+ rs485data.flags &= ~(SER_RS485_ENABLED);
+
+ if (rs485ctrl.rts_on_send)
+ rs485data.flags |= SER_RS485_RTS_ON_SEND;
+ else
+ rs485data.flags &= ~(SER_RS485_RTS_ON_SEND);
+
+ if (rs485ctrl.rts_after_sent)
+ rs485data.flags |= SER_RS485_RTS_AFTER_SEND;
+ else
+ rs485data.flags &= ~(SER_RS485_RTS_AFTER_SEND);
+
+ return e100_enable_rs485(tty, &rs485data);
}
+ case TIOCSRS485:
+ {
+ /* This is the new version of TIOCSRS485, with new
+ * data structure serial_rs485 */
+ struct serial_rs485 rs485data;
+ if (copy_from_user(&rs485data, (struct rs485_control *)arg,
+ sizeof(rs485data)))
+ return -EFAULT;
+
+ return e100_enable_rs485(tty, &rs485data);
+ }
+
+
case TIOCSERWRRS485:
{
struct rs485_write rs485wr;
@@ -3827,8 +3864,8 @@ rs_close(struct tty_struct *tty, struct file * filp)
/* port closed */
#if defined(CONFIG_ETRAX_RS485)
- if (info->rs485.enabled) {
- info->rs485.enabled = 0;
+ if (info->rs485.flags & SER_RS485_ENABLED) {
+ info->rs485.flags &= ~(SER_RS485_ENABLED);
#if defined(CONFIG_ETRAX_RS485_ON_PA)
*R_PORT_PA_DATA = port_pa_data_shadow &= ~(1 << rs485_pa_bit);
#endif
@@ -4493,10 +4530,10 @@ rs_init(void)
#if defined(CONFIG_ETRAX_RS485)
/* Set sane defaults */
- info->rs485.rts_on_send = 0;
- info->rs485.rts_after_sent = 1;
+ info->rs485.flags &= ~(SER_RS485_RTS_ON_SEND);
+ info->rs485.flags |= SER_RS485_RTS_AFTER_SEND;
info->rs485.delay_rts_before_send = 0;
- info->rs485.enabled = 0;
+ info->rs485.flags &= ~(SER_RS485_ENABLED);
#endif
INIT_WORK(&info->work, do_softint);
diff --git a/drivers/serial/crisv10.h b/drivers/serial/crisv10.h
index f36a729280bc..ea0beb46a10d 100644
--- a/drivers/serial/crisv10.h
+++ b/drivers/serial/crisv10.h
@@ -125,7 +125,7 @@ struct e100_serial {
int errorcode;
#ifdef CONFIG_ETRAX_RS485
- struct rs485_control rs485; /* RS-485 support */
+ struct serial_rs485 rs485; /* RS-485 support */
#endif
};
diff --git a/drivers/serial/icom.c b/drivers/serial/icom.c
index 2b7531d9f6ab..6579e2be1dd1 100644
--- a/drivers/serial/icom.c
+++ b/drivers/serial/icom.c
@@ -1098,7 +1098,6 @@ static void icom_set_termios(struct uart_port *port,
{
int baud;
unsigned cflag, iflag;
- int bits;
char new_config2;
char new_config3 = 0;
char tmp_byte;
@@ -1119,34 +1118,27 @@ static void icom_set_termios(struct uart_port *port,
switch (cflag & CSIZE) {
case CS5: /* 5 bits/char */
new_config2 |= ICOM_ACFG_5BPC;
- bits = 7;
break;
case CS6: /* 6 bits/char */
new_config2 |= ICOM_ACFG_6BPC;
- bits = 8;
break;
case CS7: /* 7 bits/char */
new_config2 |= ICOM_ACFG_7BPC;
- bits = 9;
break;
case CS8: /* 8 bits/char */
new_config2 |= ICOM_ACFG_8BPC;
- bits = 10;
break;
default:
- bits = 10;
break;
}
if (cflag & CSTOPB) {
/* 2 stop bits */
new_config2 |= ICOM_ACFG_2STOP_BIT;
- bits++;
}
if (cflag & PARENB) {
/* parity bit enabled */
new_config2 |= ICOM_ACFG_PARITY_ENAB;
trace(ICOM_PORT, "PARENB", 0);
- bits++;
}
if (cflag & PARODD) {
/* odd parity */
@@ -1322,7 +1314,6 @@ static struct uart_driver icom_uart_driver = {
static int __devinit icom_init_ports(struct icom_adapter *icom_adapter)
{
u32 subsystem_id = icom_adapter->subsystem_id;
- int retval = 0;
int i;
struct icom_port *icom_port;
@@ -1368,7 +1359,7 @@ static int __devinit icom_init_ports(struct icom_adapter *icom_adapter)
}
}
- return retval;
+ return 0;
}
static void icom_port_active(struct icom_port *icom_port, struct icom_adapter *icom_adapter, int port_num)
@@ -1391,7 +1382,6 @@ static int __devinit icom_load_ports(struct icom_adapter *icom_adapter)
{
struct icom_port *icom_port;
int port_num;
- int retval;
for (port_num = 0; port_num < icom_adapter->numb_ports; port_num++) {
@@ -1405,7 +1395,7 @@ static int __devinit icom_load_ports(struct icom_adapter *icom_adapter)
icom_port->adapter = icom_adapter;
/* get port memory */
- if ((retval = get_port_memory(icom_port)) != 0) {
+ if (get_port_memory(icom_port) != 0) {
dev_err(&icom_port->adapter->pci_dev->dev,
"Memory allocation for port FAILED\n");
}
diff --git a/drivers/serial/jsm/jsm_driver.c b/drivers/serial/jsm/jsm_driver.c
index ac79cbe4c2cf..d2d32a198629 100644
--- a/drivers/serial/jsm/jsm_driver.c
+++ b/drivers/serial/jsm/jsm_driver.c
@@ -52,12 +52,11 @@ int jsm_debug;
module_param(jsm_debug, int, 0);
MODULE_PARM_DESC(jsm_debug, "Driver debugging level");
-static int jsm_probe_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+static int __devinit jsm_probe_one(struct pci_dev *pdev, const struct pci_device_id *ent)
{
int rc = 0;
struct jsm_board *brd;
static int adapter_count = 0;
- int retval;
rc = pci_enable_device(pdev);
if (rc) {
@@ -134,7 +133,7 @@ static int jsm_probe_one(struct pci_dev *pdev, const struct pci_device_id *ent)
rc = jsm_tty_init(brd);
if (rc < 0) {
dev_err(&pdev->dev, "Can't init tty devices (%d)\n", rc);
- retval = -ENXIO;
+ rc = -ENXIO;
goto out_free_irq;
}
@@ -142,7 +141,7 @@ static int jsm_probe_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (rc < 0) {
/* XXX: leaking all resources from jsm_tty_init here! */
dev_err(&pdev->dev, "Can't init uart port (%d)\n", rc);
- retval = -ENXIO;
+ rc = -ENXIO;
goto out_free_irq;
}
@@ -161,7 +160,7 @@ static int jsm_probe_one(struct pci_dev *pdev, const struct pci_device_id *ent)
/* XXX: leaking all resources from jsm_tty_init and
jsm_uart_port_init here! */
dev_err(&pdev->dev, "memory allocation for flipbuf failed\n");
- retval = -ENOMEM;
+ rc = -ENOMEM;
goto out_free_irq;
}
diff --git a/drivers/serial/jsm/jsm_neo.c b/drivers/serial/jsm/jsm_neo.c
index e6390d023634..9dadaa11d266 100644
--- a/drivers/serial/jsm/jsm_neo.c
+++ b/drivers/serial/jsm/jsm_neo.c
@@ -533,7 +533,6 @@ static void neo_copy_data_from_queue_to_uart(struct jsm_channel *ch)
if (!(ch->ch_flags & (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM)))
return;
- len_written = 0;
n = UART_17158_TX_FIFOSIZE - ch->ch_t_tlevel;
/* cache head and tail of queue */
@@ -619,14 +618,10 @@ static void neo_parse_modem(struct jsm_channel *ch, u8 signals)
/* Make the UART raise any of the output signals we want up */
static void neo_assert_modem_signals(struct jsm_channel *ch)
{
- u8 out;
-
if (!ch)
return;
- out = ch->ch_mostat;
-
- writeb(out, &ch->ch_neo_uart->mcr);
+ writeb(ch->ch_mostat, &ch->ch_neo_uart->mcr);
/* flush write operation */
neo_pci_posting_flush(ch->ch_bd);
@@ -936,10 +931,9 @@ static inline void neo_parse_lsr(struct jsm_board *brd, u32 port)
static void neo_param(struct jsm_channel *ch)
{
u8 lcr = 0;
- u8 uart_lcr = 0;
- u8 ier = 0;
- u32 baud = 9600;
- int quot = 0;
+ u8 uart_lcr, ier;
+ u32 baud;
+ int quot;
struct jsm_board *bd;
bd = ch->ch_bd;
diff --git a/drivers/serial/jsm/jsm_tty.c b/drivers/serial/jsm/jsm_tty.c
index 324c74d2f666..31496dc0a0d1 100644
--- a/drivers/serial/jsm/jsm_tty.c
+++ b/drivers/serial/jsm/jsm_tty.c
@@ -183,7 +183,6 @@ static void jsm_tty_break(struct uart_port *port, int break_state)
static int jsm_tty_open(struct uart_port *port)
{
struct jsm_board *brd;
- int rc = 0;
struct jsm_channel *channel = (struct jsm_channel *)port;
struct ktermios *termios;
@@ -265,7 +264,7 @@ static int jsm_tty_open(struct uart_port *port)
channel->ch_open_count++;
jsm_printk(OPEN, INFO, &channel->ch_bd->pci_dev, "finish\n");
- return rc;
+ return 0;
}
static void jsm_tty_close(struct uart_port *port)
@@ -367,7 +366,7 @@ static struct uart_ops jsm_ops = {
* Init the tty subsystem. Called once per board after board has been
* downloaded and init'ed.
*/
-int jsm_tty_init(struct jsm_board *brd)
+int __devinit jsm_tty_init(struct jsm_board *brd)
{
int i;
void __iomem *vaddr;
@@ -431,7 +430,7 @@ int jsm_tty_init(struct jsm_board *brd)
return 0;
}
-int jsm_uart_port_init(struct jsm_board *brd)
+int __devinit jsm_uart_port_init(struct jsm_board *brd)
{
int i;
struct jsm_channel *ch;
@@ -748,7 +747,7 @@ static void jsm_carrier(struct jsm_channel *ch)
void jsm_check_queue_flow_control(struct jsm_channel *ch)
{
struct board_ops *bd_ops = ch->ch_bd->bd_ops;
- int qleft = 0;
+ int qleft;
/* Store how much space we have left in the queue */
if ((qleft = ch->ch_r_tail - ch->ch_r_head - 1) < 0)
@@ -834,7 +833,7 @@ void jsm_check_queue_flow_control(struct jsm_channel *ch)
*/
int jsm_tty_write(struct uart_port *port)
{
- int bufcount = 0, n = 0;
+ int bufcount;
int data_count = 0,data_count1 =0;
u16 head;
u16 tail;
@@ -850,14 +849,12 @@ int jsm_tty_write(struct uart_port *port)
if ((bufcount = tail - head - 1) < 0)
bufcount += WQUEUESIZE;
- n = bufcount;
-
- n = min(n, 56);
+ bufcount = min(bufcount, 56);
remain = WQUEUESIZE - head;
data_count = 0;
- if (n >= remain) {
- n -= remain;
+ if (bufcount >= remain) {
+ bufcount -= remain;
while ((port->info->xmit.head != temp_tail) &&
(data_count < remain)) {
channel->ch_wqueue[head++] =
@@ -871,8 +868,8 @@ int jsm_tty_write(struct uart_port *port)
}
data_count1 = 0;
- if (n > 0) {
- remain = n;
+ if (bufcount > 0) {
+ remain = bufcount;
while ((port->info->xmit.head != temp_tail) &&
(data_count1 < remain)) {
channel->ch_wqueue[head++] =
diff --git a/drivers/serial/mcf.c b/drivers/serial/mcf.c
index 56841fe5f483..0eefb07bebaf 100644
--- a/drivers/serial/mcf.c
+++ b/drivers/serial/mcf.c
@@ -513,7 +513,7 @@ static int __init mcf_console_setup(struct console *co, char *options)
int parity = 'n';
int flow = 'n';
- if ((co->index >= 0) && (co->index <= MCF_MAXPORTS))
+ if ((co->index < 0) || (co->index >= MCF_MAXPORTS))
co->index = 0;
port = &mcf_ports[co->index].port;
if (port->membase == 0)
diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c
index 0c3a2ab1612c..7f72f8ceaa6f 100644
--- a/drivers/serial/mpc52xx_uart.c
+++ b/drivers/serial/mpc52xx_uart.c
@@ -50,8 +50,8 @@
/* OF Platform device Usage :
*
* This driver is only used for PSCs configured in uart mode. The device
- * tree will have a node for each PSC in uart mode w/ device_type = "serial"
- * and "mpc52xx-psc-uart" in the compatible string
+ * tree will have a node for each PSC with "mpc52xx-psc-uart" in the compatible
+ * list.
*
* By default, PSC devices are enumerated in the order they are found. However
* a particular PSC number can be forces by adding 'device_no = <port#>'
@@ -522,7 +522,7 @@ mpc52xx_uart_startup(struct uart_port *port)
/* Request IRQ */
ret = request_irq(port->irq, mpc52xx_uart_int,
- IRQF_DISABLED | IRQF_SAMPLE_RANDOM | IRQF_SHARED,
+ IRQF_DISABLED | IRQF_SAMPLE_RANDOM,
"mpc52xx_psc_uart", port);
if (ret)
return ret;
@@ -1212,30 +1212,18 @@ mpc52xx_uart_of_resume(struct of_device *op)
#endif
static void
-mpc52xx_uart_of_assign(struct device_node *np, int idx)
+mpc52xx_uart_of_assign(struct device_node *np)
{
- int free_idx = -1;
int i;
- /* Find the first free node */
+ /* Find the first free PSC number */
for (i = 0; i < MPC52xx_PSC_MAXNUM; i++) {
if (mpc52xx_uart_nodes[i] == NULL) {
- free_idx = i;
- break;
+ of_node_get(np);
+ mpc52xx_uart_nodes[i] = np;
+ return;
}
}
-
- if ((idx < 0) || (idx >= MPC52xx_PSC_MAXNUM))
- idx = free_idx;
-
- if (idx < 0)
- return; /* No free slot; abort */
-
- of_node_get(np);
- /* If the slot is already occupied, then swap slots */
- if (mpc52xx_uart_nodes[idx] && (free_idx != -1))
- mpc52xx_uart_nodes[free_idx] = mpc52xx_uart_nodes[idx];
- mpc52xx_uart_nodes[idx] = np;
}
static void
@@ -1243,23 +1231,17 @@ mpc52xx_uart_of_enumerate(void)
{
static int enum_done;
struct device_node *np;
- const unsigned int *devno;
const struct of_device_id *match;
int i;
if (enum_done)
return;
- for_each_node_by_type(np, "serial") {
+ /* Assign index to each PSC in device tree */
+ for_each_matching_node(np, mpc52xx_uart_of_match) {
match = of_match_node(mpc52xx_uart_of_match, np);
- if (!match)
- continue;
-
psc_ops = match->data;
-
- /* Is a particular device number requested? */
- devno = of_get_property(np, "port-number", NULL);
- mpc52xx_uart_of_assign(np, devno ? *devno : -1);
+ mpc52xx_uart_of_assign(np);
}
enum_done = 1;
diff --git a/drivers/serial/pmac_zilog.c b/drivers/serial/pmac_zilog.c
index ad3488504010..9c1243fbd512 100644
--- a/drivers/serial/pmac_zilog.c
+++ b/drivers/serial/pmac_zilog.c
@@ -1538,6 +1538,21 @@ no_dma:
uap->port.type = PORT_PMAC_ZILOG;
uap->port.flags = 0;
+ /*
+ * Fixup for the port on Gatwick for which the device-tree has
+ * missing interrupts. Normally, the macio_dev would contain
+ * fixed up interrupt info, but we use the device-tree directly
+ * here due to early probing so we need the fixup too.
+ */
+ if (uap->port.irq == NO_IRQ &&
+ np->parent && np->parent->parent &&
+ of_device_is_compatible(np->parent->parent, "gatwick")) {
+ /* IRQs on gatwick are offset by 64 */
+ uap->port.irq = irq_create_mapping(NULL, 64 + 15);
+ uap->tx_dma_irq = irq_create_mapping(NULL, 64 + 4);
+ uap->rx_dma_irq = irq_create_mapping(NULL, 64 + 5);
+ }
+
/* Setup some valid baud rate information in the register
* shadows so we don't write crap there before baud rate is
* first initialized.
diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c
index 42f4e66fccaf..b0bb29d804ae 100644
--- a/drivers/serial/serial_core.c
+++ b/drivers/serial/serial_core.c
@@ -27,6 +27,8 @@
#include <linux/slab.h>
#include <linux/init.h>
#include <linux/console.h>
+#include <linux/proc_fs.h>
+#include <linux/seq_file.h>
#include <linux/serial_core.h>
#include <linux/smp_lock.h>
#include <linux/device.h>
@@ -1682,20 +1684,20 @@ static const char *uart_type(struct uart_port *port)
#ifdef CONFIG_PROC_FS
-static int uart_line_info(char *buf, struct uart_driver *drv, int i)
+static void uart_line_info(struct seq_file *m, struct uart_driver *drv, int i)
{
struct uart_state *state = drv->state + i;
int pm_state;
struct uart_port *port = state->port;
char stat_buf[32];
unsigned int status;
- int mmio, ret;
+ int mmio;
if (!port)
- return 0;
+ return;
mmio = port->iotype >= UPIO_MEM;
- ret = sprintf(buf, "%d: uart:%s %s%08llX irq:%d",
+ seq_printf(m, "%d: uart:%s %s%08llX irq:%d",
port->line, uart_type(port),
mmio ? "mmio:0x" : "port:",
mmio ? (unsigned long long)port->mapbase
@@ -1703,8 +1705,8 @@ static int uart_line_info(char *buf, struct uart_driver *drv, int i)
port->irq);
if (port->type == PORT_UNKNOWN) {
- strcat(buf, "\n");
- return ret + 1;
+ seq_putc(m, '\n');
+ return;
}
if (capable(CAP_SYS_ADMIN)) {
@@ -1719,19 +1721,19 @@ static int uart_line_info(char *buf, struct uart_driver *drv, int i)
uart_change_pm(state, pm_state);
mutex_unlock(&state->mutex);
- ret += sprintf(buf + ret, " tx:%d rx:%d",
+ seq_printf(m, " tx:%d rx:%d",
port->icount.tx, port->icount.rx);
if (port->icount.frame)
- ret += sprintf(buf + ret, " fe:%d",
+ seq_printf(m, " fe:%d",
port->icount.frame);
if (port->icount.parity)
- ret += sprintf(buf + ret, " pe:%d",
+ seq_printf(m, " pe:%d",
port->icount.parity);
if (port->icount.brk)
- ret += sprintf(buf + ret, " brk:%d",
+ seq_printf(m, " brk:%d",
port->icount.brk);
if (port->icount.overrun)
- ret += sprintf(buf + ret, " oe:%d",
+ seq_printf(m, " oe:%d",
port->icount.overrun);
#define INFOBIT(bit, str) \
@@ -1753,45 +1755,39 @@ static int uart_line_info(char *buf, struct uart_driver *drv, int i)
STATBIT(TIOCM_RNG, "|RI");
if (stat_buf[0])
stat_buf[0] = ' ';
- strcat(stat_buf, "\n");
- ret += sprintf(buf + ret, stat_buf);
- } else {
- strcat(buf, "\n");
- ret++;
+ seq_puts(m, stat_buf);
}
+ seq_putc(m, '\n');
#undef STATBIT
#undef INFOBIT
- return ret;
}
-static int uart_read_proc(char *page, char **start, off_t off,
- int count, int *eof, void *data)
+static int uart_proc_show(struct seq_file *m, void *v)
{
- struct tty_driver *ttydrv = data;
+ struct tty_driver *ttydrv = m->private;
struct uart_driver *drv = ttydrv->driver_state;
- int i, len = 0, l;
- off_t begin = 0;
+ int i;
- len += sprintf(page, "serinfo:1.0 driver%s%s revision:%s\n",
+ seq_printf(m, "serinfo:1.0 driver%s%s revision:%s\n",
"", "", "");
- for (i = 0; i < drv->nr && len < PAGE_SIZE - 96; i++) {
- l = uart_line_info(page + len, drv, i);
- len += l;
- if (len + begin > off + count)
- goto done;
- if (len + begin < off) {
- begin += len;
- len = 0;
- }
- }
- *eof = 1;
- done:
- if (off >= len + begin)
- return 0;
- *start = page + (off - begin);
- return (count < begin + len - off) ? count : (begin + len - off);
+ for (i = 0; i < drv->nr; i++)
+ uart_line_info(m, drv, i);
+ return 0;
}
+
+static int uart_proc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, uart_proc_show, PDE(inode)->data);
+}
+
+static const struct file_operations uart_proc_fops = {
+ .owner = THIS_MODULE,
+ .open = uart_proc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
#endif
#if defined(CONFIG_SERIAL_CORE_CONSOLE) || defined(CONFIG_CONSOLE_POLL)
@@ -2299,7 +2295,7 @@ static const struct tty_operations uart_ops = {
.break_ctl = uart_break_ctl,
.wait_until_sent= uart_wait_until_sent,
#ifdef CONFIG_PROC_FS
- .read_proc = uart_read_proc,
+ .proc_fops = &uart_proc_fops,
#endif
.tiocmget = uart_tiocmget,
.tiocmset = uart_tiocmset,
diff --git a/drivers/serial/ucc_uart.c b/drivers/serial/ucc_uart.c
index 315a9333ca3c..7de66c06b05d 100644
--- a/drivers/serial/ucc_uart.c
+++ b/drivers/serial/ucc_uart.c
@@ -1274,6 +1274,7 @@ static int ucc_uart_probe(struct of_device *ofdev,
if (!iprop) {
iprop = of_get_property(np, "device-id", NULL);
if (!iprop) {
+ kfree(qe_port);
dev_err(&ofdev->dev, "UCC is unspecified in "
"device tree\n");
return -EINVAL;
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.