diff options
Diffstat (limited to 'drivers/staging/ath6kl/Kconfig')
-rw-r--r-- | drivers/staging/ath6kl/Kconfig | 158 |
1 files changed, 0 insertions, 158 deletions
diff --git a/drivers/staging/ath6kl/Kconfig b/drivers/staging/ath6kl/Kconfig deleted file mode 100644 index afd6cc16a2b8..000000000000 --- a/drivers/staging/ath6kl/Kconfig +++ /dev/null @@ -1,158 +0,0 @@ -config ATH6K_LEGACY - tristate "Atheros AR6003 support (non mac80211)" - depends on MMC && WLAN - depends on CFG80211 - select WIRELESS_EXT - select WEXT_PRIV - help - This module adds support for wireless adapters based on Atheros AR6003 chipset running over SDIO. If you choose to build it as a module, it will be called ath6kl. Pls note that AR6002 and AR6001 are not supported by this driver. - -choice - prompt "AR6003 Board Data Configuration" - depends on ATH6K_LEGACY - default AR600x_SD31_XXX - help - Select the appropriate board data template from the list below that matches your AR6003 based reference design. - -config AR600x_SD31_XXX - bool "SD31-xxx" - help - Board Data file for a standard SD31 reference design (File: bdata.SD31.bin) - -config AR600x_WB31_XXX - bool "WB31-xxx" - help - Board Data file for a standard WB31 (BT/WiFi) reference design (File: bdata.WB31.bin) - -config AR600x_SD32_XXX - bool "SD32-xxx" - help - Board Data file for a standard SD32 (5GHz) reference design (File: bdata.SD32.bin) - -config AR600x_CUSTOM_XXX - bool "CUSTOM-xxx" - help - Board Data file for a custom reference design (File: should be named as bdata.CUSTOM.bin) -endchoice - -config ATH6KL_ENABLE_COEXISTENCE - bool "BT Coexistence support" - depends on ATH6K_LEGACY - help - Enables WLAN/BT coexistence support. Select the apprpriate configuration from below. - -choice - prompt "Front-End Antenna Configuration" - depends on ATH6KL_ENABLE_COEXISTENCE - default AR600x_DUAL_ANTENNA - help - Indicates the number of antennas being used by BT and WLAN. Select the appropriate configuration from the list below that matches your AR6003 based reference design. - -config AR600x_DUAL_ANTENNA - bool "Dual Antenna" - help - Dual Antenna Design - -config AR600x_SINGLE_ANTENNA - bool "Single Antenna" - help - Single Antenna Design -endchoice - -choice - prompt "Collocated Bluetooth Type" - depends on ATH6KL_ENABLE_COEXISTENCE - default AR600x_BT_AR3001 - help - Select the appropriate configuration from the list below that matches your AR6003 based reference design. - -config AR600x_BT_QCOM - bool "Qualcomm BTS4020X" - help - Qualcomm BT (3 Wire PTA) - -config AR600x_BT_CSR - bool "CSR BC06" - help - CSR BT (3 Wire PTA) - -config AR600x_BT_AR3001 - bool "Atheros AR3001" - help - Atheros BT (3 Wire PTA) -endchoice - -config ATH6KL_HCI_BRIDGE - bool "HCI over SDIO support" - depends on ATH6K_LEGACY - help - Enables BT over SDIO. Applicable only for combo designs (eg: WB31) - -config ATH6KL_CONFIG_GPIO_BT_RESET - bool "Configure BT Reset GPIO" - depends on ATH6KL_HCI_BRIDGE - help - Configure a WLAN GPIO for use with BT. - -config AR600x_BT_RESET_PIN - int "GPIO" - depends on ATH6KL_CONFIG_GPIO_BT_RESET - default 22 - help - WLAN GPIO to be used for resetting BT - -config ATH6KL_HTC_RAW_INTERFACE - bool "RAW HTC support" - depends on ATH6K_LEGACY - help - Enables raw HTC interface. Allows application to directly talk to the HTC interface via the ioctl interface - -config ATH6KL_VIRTUAL_SCATTER_GATHER - bool "Virtual Scatter-Gather support" - depends on ATH6K_LEGACY - help - Enables virtual scatter gather support for the hardware that does not support it natively. - -config ATH6KL_SKIP_ABI_VERSION_CHECK - bool "Skip ABI version check support" - depends on ATH6K_LEGACY - help - Forces the driver to disable ABI version check. Caution: Incompatilbity between the host driver and target firmware may lead to unknown side effects. - -config ATH6KL_BT_UART_FC_POLARITY - int "UART Flow Control Polarity" - depends on ATH6KL_LEGACY - default 0 - help - Configures the polarity of UART Flow Control. A value of 0 implies active low and is the default setting. Set it to 1 for active high. - -config ATH6KL_DEBUG - bool "Debug support" - depends on ATH6K_LEGACY - help - Enables debug support - -config ATH6KL_ENABLE_HOST_DEBUG - bool "Host Debug support" - depends on ATH6KL_DEBUG - help - Enables debug support in the driver - -config ATH6KL_ENABLE_TARGET_DEBUG_PRINTS - bool "Target Debug support - Enable UART prints" - depends on ATH6KL_DEBUG - help - Enables uart prints - -config AR600x_DEBUG_UART_TX_PIN - int "GPIO" - depends on ATH6KL_ENABLE_TARGET_DEBUG_PRINTS - default 8 - help - WLAN GPIO to be used for Debug UART (Tx) - -config ATH6KL_DISABLE_TARGET_DBGLOGS - bool "Target Debug support - Disable Debug logs" - depends on ATH6KL_DEBUG - help - Enables debug logs |