diff options
Diffstat (limited to 'drivers/staging/irda/drivers/sa1100_ir.c')
| -rw-r--r-- | drivers/staging/irda/drivers/sa1100_ir.c | 1150 |
1 files changed, 1150 insertions, 0 deletions
diff --git a/drivers/staging/irda/drivers/sa1100_ir.c b/drivers/staging/irda/drivers/sa1100_ir.c new file mode 100644 index 000000000000..b6e44ff4e373 --- /dev/null +++ b/drivers/staging/irda/drivers/sa1100_ir.c @@ -0,0 +1,1150 @@ +/* + * linux/drivers/net/irda/sa1100_ir.c + * + * Copyright (C) 2000-2001 Russell King + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Infra-red driver for the StrongARM SA1100 embedded microprocessor + * + * Note that we don't have to worry about the SA1111's DMA bugs in here, + * so we use the straight forward dma_map_* functions with a null pointer. + * + * This driver takes one kernel command line parameter, sa1100ir=, with + * the following options: + * max_rate:baudrate - set the maximum baud rate + * power_level:level - set the transmitter power level + * tx_lpm:0|1 - set transmit low power mode + */ +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/types.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/netdevice.h> +#include <linux/slab.h> +#include <linux/rtnetlink.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/platform_device.h> +#include <linux/dma-mapping.h> +#include <linux/dmaengine.h> +#include <linux/sa11x0-dma.h> + +#include <net/irda/irda.h> +#include <net/irda/wrapper.h> +#include <net/irda/irda_device.h> + +#include <mach/hardware.h> +#include <linux/platform_data/irda-sa11x0.h> + +static int power_level = 3; +static int tx_lpm; +static int max_rate = 4000000; + +struct sa1100_buf { + struct device *dev; + struct sk_buff *skb; + struct scatterlist sg; + struct dma_chan *chan; + dma_cookie_t cookie; +}; + +struct sa1100_irda { + unsigned char utcr4; + unsigned char power; + unsigned char open; + + int speed; + int newspeed; + + struct sa1100_buf dma_rx; + struct sa1100_buf dma_tx; + + struct device *dev; + struct irda_platform_data *pdata; + struct irlap_cb *irlap; + struct qos_info qos; + + iobuff_t tx_buff; + iobuff_t rx_buff; + + int (*tx_start)(struct sk_buff *, struct net_device *, struct sa1100_irda *); + irqreturn_t (*irq)(struct net_device *, struct sa1100_irda *); +}; + +static int sa1100_irda_set_speed(struct sa1100_irda *, int); + +#define IS_FIR(si) ((si)->speed >= 4000000) + +#define HPSIR_MAX_RXLEN 2047 + +static struct dma_slave_config sa1100_irda_sir_tx = { + .direction = DMA_TO_DEVICE, + .dst_addr = __PREG(Ser2UTDR), + .dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE, + .dst_maxburst = 4, +}; + +static struct dma_slave_config sa1100_irda_fir_rx = { + .direction = DMA_FROM_DEVICE, + .src_addr = __PREG(Ser2HSDR), + .src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE, + .src_maxburst = 8, +}; + +static struct dma_slave_config sa1100_irda_fir_tx = { + .direction = DMA_TO_DEVICE, + .dst_addr = __PREG(Ser2HSDR), + .dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE, + .dst_maxburst = 8, +}; + +static unsigned sa1100_irda_dma_xferred(struct sa1100_buf *buf) +{ + struct dma_chan *chan = buf->chan; + struct dma_tx_state state; + enum dma_status status; + + status = chan->device->device_tx_status(chan, buf->cookie, &state); + if (status != DMA_PAUSED) + return 0; + + return sg_dma_len(&buf->sg) - state.residue; +} + +static int sa1100_irda_dma_request(struct device *dev, struct sa1100_buf *buf, + const char *name, struct dma_slave_config *cfg) +{ + dma_cap_mask_t m; + int ret; + + dma_cap_zero(m); + dma_cap_set(DMA_SLAVE, m); + + buf->chan = dma_request_channel(m, sa11x0_dma_filter_fn, (void *)name); + if (!buf->chan) { + dev_err(dev, "unable to request DMA channel for %s\n", + name); + return -ENOENT; + } + + ret = dmaengine_slave_config(buf->chan, cfg); + if (ret) + dev_warn(dev, "DMA slave_config for %s returned %d\n", + name, ret); + + buf->dev = buf->chan->device->dev; + + return 0; +} + +static void sa1100_irda_dma_start(struct sa1100_buf *buf, + enum dma_transfer_direction dir, dma_async_tx_callback cb, void *cb_p) +{ + struct dma_async_tx_descriptor *desc; + struct dma_chan *chan = buf->chan; + + desc = dmaengine_prep_slave_sg(chan, &buf->sg, 1, dir, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (desc) { + desc->callback = cb; + desc->callback_param = cb_p; + buf->cookie = dmaengine_submit(desc); + dma_async_issue_pending(chan); + } +} + +/* + * Allocate and map the receive buffer, unless it is already allocated. + */ +static int sa1100_irda_rx_alloc(struct sa1100_irda *si) +{ + if (si->dma_rx.skb) + return 0; + + si->dma_rx.skb = alloc_skb(HPSIR_MAX_RXLEN + 1, GFP_ATOMIC); + if (!si->dma_rx.skb) { + printk(KERN_ERR "sa1100_ir: out of memory for RX SKB\n"); + return -ENOMEM; + } + + /* + * Align any IP headers that may be contained + * within the frame. + */ + skb_reserve(si->dma_rx.skb, 1); + + sg_set_buf(&si->dma_rx.sg, si->dma_rx.skb->data, HPSIR_MAX_RXLEN); + if (dma_map_sg(si->dma_rx.dev, &si->dma_rx.sg, 1, DMA_FROM_DEVICE) == 0) { + dev_kfree_skb_any(si->dma_rx.skb); + return -ENOMEM; + } + + return 0; +} + +/* + * We want to get here as soon as possible, and get the receiver setup. + * We use the existing buffer. + */ +static void sa1100_irda_rx_dma_start(struct sa1100_irda *si) +{ + if (!si->dma_rx.skb) { + printk(KERN_ERR "sa1100_ir: rx buffer went missing\n"); + return; + } + + /* + * First empty receive FIFO + */ + Ser2HSCR0 = HSCR0_HSSP; + + /* + * Enable the DMA, receiver and receive interrupt. + */ + dmaengine_terminate_all(si->dma_rx.chan); + sa1100_irda_dma_start(&si->dma_rx, DMA_DEV_TO_MEM, NULL, NULL); + + Ser2HSCR0 = HSCR0_HSSP | HSCR0_RXE; +} + +static void sa1100_irda_check_speed(struct sa1100_irda *si) +{ + if (si->newspeed) { + sa1100_irda_set_speed(si, si->newspeed); + si->newspeed = 0; + } +} + +/* + * HP-SIR format support. + */ +static void sa1100_irda_sirtxdma_irq(void *id) +{ + struct net_device *dev = id; + struct sa1100_irda *si = netdev_priv(dev); + + dma_unmap_sg(si->dma_tx.dev, &si->dma_tx.sg, 1, DMA_TO_DEVICE); + dev_kfree_skb(si->dma_tx.skb); + si->dma_tx.skb = NULL; + + dev->stats.tx_packets++; + dev->stats.tx_bytes += sg_dma_len(&si->dma_tx.sg); + + /* We need to ensure that the transmitter has finished. */ + do + rmb(); + while (Ser2UTSR1 & UTSR1_TBY); + + /* + * Ok, we've finished transmitting. Now enable the receiver. + * Sometimes we get a receive IRQ immediately after a transmit... + */ + Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID; + Ser2UTCR3 = UTCR3_RIE | UTCR3_RXE | UTCR3_TXE; + + sa1100_irda_check_speed(si); + + /* I'm hungry! */ + netif_wake_queue(dev); +} + +static int sa1100_irda_sir_tx_start(struct sk_buff *skb, struct net_device *dev, + struct sa1100_irda *si) +{ + si->tx_buff.data = si->tx_buff.head; + si->tx_buff.len = async_wrap_skb(skb, si->tx_buff.data, + si->tx_buff.truesize); + + si->dma_tx.skb = skb; + sg_set_buf(&si->dma_tx.sg, si->tx_buff.data, si->tx_buff.len); + if (dma_map_sg(si->dma_tx.dev, &si->dma_tx.sg, 1, DMA_TO_DEVICE) == 0) { + si->dma_tx.skb = NULL; + netif_wake_queue(dev); + dev->stats.tx_dropped++; + return NETDEV_TX_OK; + } + + sa1100_irda_dma_start(&si->dma_tx, DMA_MEM_TO_DEV, sa1100_irda_sirtxdma_irq, dev); + + /* + * The mean turn-around time is enforced by XBOF padding, + * so we don't have to do anything special here. + */ + Ser2UTCR3 = UTCR3_TXE; + + return NETDEV_TX_OK; +} + +static irqreturn_t sa1100_irda_sir_irq(struct net_device *dev, struct sa1100_irda *si) +{ + int status; + + status = Ser2UTSR0; + + /* + * Deal with any receive errors first. The bytes in error may be + * the only bytes in the receive FIFO, so we do this first. + */ + while (status & UTSR0_EIF) { + int stat, data; + + stat = Ser2UTSR1; + data = Ser2UTDR; + + if (stat & (UTSR1_FRE | UTSR1_ROR)) { + dev->stats.rx_errors++; + if (stat & UTSR1_FRE) + dev->stats.rx_frame_errors++; + if (stat & UTSR1_ROR) + dev->stats.rx_fifo_errors++; + } else + async_unwrap_char(dev, &dev->stats, &si->rx_buff, data); + + status = Ser2UTSR0; + } + + /* + * We must clear certain bits. + */ + Ser2UTSR0 = status & (UTSR0_RID | UTSR0_RBB | UTSR0_REB); + + if (status & UTSR0_RFS) { + /* + * There are at least 4 bytes in the FIFO. Read 3 bytes + * and leave the rest to the block below. + */ + async_unwrap_char(dev, &dev->stats, &si->rx_buff, Ser2UTDR); + async_unwrap_char(dev, &dev->stats, &si->rx_buff, Ser2UTDR); + async_unwrap_char(dev, &dev->stats, &si->rx_buff, Ser2UTDR); + } + + if (status & (UTSR0_RFS | UTSR0_RID)) { + /* + * Fifo contains more than 1 character. + */ + do { + async_unwrap_char(dev, &dev->stats, &si->rx_buff, + Ser2UTDR); + } while (Ser2UTSR1 & UTSR1_RNE); + + } + + return IRQ_HANDLED; +} + +/* + * FIR format support. + */ +static void sa1100_irda_firtxdma_irq(void *id) +{ + struct net_device *dev = id; + struct sa1100_irda *si = netdev_priv(dev); + struct sk_buff *skb; + + /* + * Wait for the transmission to complete. Unfortunately, + * the hardware doesn't give us an interrupt to indicate + * "end of frame". + */ + do + rmb(); + while (!(Ser2HSSR0 & HSSR0_TUR) || Ser2HSSR1 & HSSR1_TBY); + + /* + * Clear the transmit underrun bit. + */ + Ser2HSSR0 = HSSR0_TUR; + + /* + * Do we need to change speed? Note that we're lazy + * here - we don't free the old dma_rx.skb. We don't need + * to allocate a buffer either. + */ + sa1100_irda_check_speed(si); + + /* + * Start reception. This disables the transmitter for + * us. This will be using the existing RX buffer. + */ + sa1100_irda_rx_dma_start(si); + + /* Account and free the packet. */ + skb = si->dma_tx.skb; + if (skb) { + dma_unmap_sg(si->dma_tx.dev, &si->dma_tx.sg, 1, + DMA_TO_DEVICE); + dev->stats.tx_packets ++; + dev->stats.tx_bytes += skb->len; + dev_kfree_skb_irq(skb); + si->dma_tx.skb = NULL; + } + + /* + * Make sure that the TX queue is available for sending + * (for retries). TX has priority over RX at all times. + */ + netif_wake_queue(dev); +} + +static int sa1100_irda_fir_tx_start(struct sk_buff *skb, struct net_device *dev, + struct sa1100_irda *si) +{ + int mtt = irda_get_mtt(skb); + + si->dma_tx.skb = skb; + sg_set_buf(&si->dma_tx.sg, skb->data, skb->len); + if (dma_map_sg(si->dma_tx.dev, &si->dma_tx.sg, 1, DMA_TO_DEVICE) == 0) { + si->dma_tx.skb = NULL; + netif_wake_queue(dev); + dev->stats.tx_dropped++; + dev_kfree_skb(skb); + return NETDEV_TX_OK; + } + + sa1100_irda_dma_start(&si->dma_tx, DMA_MEM_TO_DEV, sa1100_irda_firtxdma_irq, dev); + + /* + * If we have a mean turn-around time, impose the specified + * specified delay. We could shorten this by timing from + * the point we received the packet. + */ + if (mtt) + udelay(mtt); + + Ser2HSCR0 = HSCR0_HSSP | HSCR0_TXE; + + return NETDEV_TX_OK; +} + +static void sa1100_irda_fir_error(struct sa1100_irda *si, struct net_device *dev) +{ + struct sk_buff *skb = si->dma_rx.skb; + unsigned int len, stat, data; + + if (!skb) { + printk(KERN_ERR "sa1100_ir: SKB is NULL!\n"); + return; + } + + /* + * Get the current data position. + */ + len = sa1100_irda_dma_xferred(&si->dma_rx); + if (len > HPSIR_MAX_RXLEN) + len = HPSIR_MAX_RXLEN; + dma_unmap_sg(si->dma_rx.dev, &si->dma_rx.sg, 1, DMA_FROM_DEVICE); + + do { + /* + * Read Status, and then Data. + */ + stat = Ser2HSSR1; + rmb(); + data = Ser2HSDR; + + if (stat & (HSSR1_CRE | HSSR1_ROR)) { + dev->stats.rx_errors++; + if (stat & HSSR1_CRE) + dev->stats.rx_crc_errors++; + if (stat & HSSR1_ROR) + dev->stats.rx_frame_errors++; + } else + skb->data[len++] = data; + + /* + * If we hit the end of frame, there's + * no point in continuing. + */ + if (stat & HSSR1_EOF) + break; + } while (Ser2HSSR0 & HSSR0_EIF); + + if (stat & HSSR1_EOF) { + si->dma_rx.skb = NULL; + + skb_put(skb, len); + skb->dev = dev; + skb_reset_mac_header(skb); + skb->protocol = htons(ETH_P_IRDA); + dev->stats.rx_packets++; + dev->stats.rx_bytes += len; + + /* + * Before we pass the buffer up, allocate a new one. + */ + sa1100_irda_rx_alloc(si); + + netif_rx(skb); + } else { + /* + * Remap the buffer - it was previously mapped, and we + * hope that this succeeds. + */ + dma_map_sg(si->dma_rx.dev, &si->dma_rx.sg, 1, DMA_FROM_DEVICE); + } +} + +/* + * We only have to handle RX events here; transmit events go via the TX + * DMA handler. We disable RX, process, and the restart RX. + */ +static irqreturn_t sa1100_irda_fir_irq(struct net_device *dev, struct sa1100_irda *si) +{ + /* + * Stop RX DMA + */ + dmaengine_pause(si->dma_rx.chan); + + /* + * Framing error - we throw away the packet completely. + * Clearing RXE flushes the error conditions and data + * from the fifo. + */ + if (Ser2HSSR0 & (HSSR0_FRE | HSSR0_RAB)) { + dev->stats.rx_errors++; + + if (Ser2HSSR0 & HSSR0_FRE) + dev->stats.rx_frame_errors++; + + /* + * Clear out the DMA... + */ + Ser2HSCR0 = HSCR0_HSSP; + + /* + * Clear selected status bits now, so we + * don't miss them next time around. + */ + Ser2HSSR0 = HSSR0_FRE | HSSR0_RAB; + } + + /* + * Deal with any receive errors. The any of the lowest + * 8 bytes in the FIFO may contain an error. We must read + * them one by one. The "error" could even be the end of + * packet! + */ + if (Ser2HSSR0 & HSSR0_EIF) + sa1100_irda_fir_error(si, dev); + + /* + * No matter what happens, we must restart reception. + */ + sa1100_irda_rx_dma_start(si); + + return IRQ_HANDLED; +} + +/* + * Set the IrDA communications speed. + */ +static int sa1100_irda_set_speed(struct sa1100_irda *si, int speed) +{ + unsigned long flags; + int brd, ret = -EINVAL; + + switch (speed) { + case 9600: case 19200: case 38400: + case 57600: case 115200: + brd = 3686400 / (16 * speed) - 1; + + /* Stop the receive DMA, and configure transmit. */ + if (IS_FIR(si)) { + dmaengine_terminate_all(si->dma_rx.chan); + dmaengine_slave_config(si->dma_tx.chan, + &sa1100_irda_sir_tx); + } + + local_irq_save(flags); + + Ser2UTCR3 = 0; + Ser2HSCR0 = HSCR0_UART; + + Ser2UTCR1 = brd >> 8; + Ser2UTCR2 = brd; + + /* + * Clear status register + */ + Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID; + Ser2UTCR3 = UTCR3_RIE | UTCR3_RXE | UTCR3_TXE; + + if (si->pdata->set_speed) + si->pdata->set_speed(si->dev, speed); + + si->speed = speed; + si->tx_start = sa1100_irda_sir_tx_start; + si->irq = sa1100_irda_sir_irq; + + local_irq_restore(flags); + ret = 0; + break; + + case 4000000: + if (!IS_FIR(si)) + dmaengine_slave_config(si->dma_tx.chan, + &sa1100_irda_fir_tx); + + local_irq_save(flags); + + Ser2HSSR0 = 0xff; + Ser2HSCR0 = HSCR0_HSSP; + Ser2UTCR3 = 0; + + si->speed = speed; + si->tx_start = sa1100_irda_fir_tx_start; + si->irq = sa1100_irda_fir_irq; + + if (si->pdata->set_speed) + si->pdata->set_speed(si->dev, speed); + + sa1100_irda_rx_alloc(si); + sa1100_irda_rx_dma_start(si); + + local_irq_restore(flags); + + break; + + default: + break; + } + + return ret; +} + +/* + * Control the power state of the IrDA transmitter. + * State: + * 0 - off + * 1 - short range, lowest power + * 2 - medium range, medium power + * 3 - maximum range, high power + * + * Currently, only assabet is known to support this. + */ +static int +__sa1100_irda_set_power(struct sa1100_irda *si, unsigned int state) +{ + int ret = 0; + if (si->pdata->set_power) + ret = si->pdata->set_power(si->dev, state); + return ret; +} + +static inline int +sa1100_set_power(struct sa1100_irda *si, unsigned int state) +{ + int ret; + + ret = __sa1100_irda_set_power(si, state); + if (ret == 0) + si->power = state; + + return ret; +} + +static irqreturn_t sa1100_irda_irq(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + struct sa1100_irda *si = netdev_priv(dev); + + return si->irq(dev, si); +} + +static int sa1100_irda_hard_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct sa1100_irda *si = netdev_priv(dev); + int speed = irda_get_next_speed(skb); + + /* + * Does this packet contain a request to change the interface + * speed? If so, remember it until we complete the transmission + * of this frame. + */ + if (speed != si->speed && speed != -1) + si->newspeed = speed; + + /* If this is an empty frame, we can bypass a lot. */ + if (skb->len == 0) { + sa1100_irda_check_speed(si); + dev_kfree_skb(skb); + return NETDEV_TX_OK; + } + + netif_stop_queue(dev); + + /* We must not already have a skb to transmit... */ + BUG_ON(si->dma_tx.skb); + + return si->tx_start(skb, dev, si); +} + +static int +sa1100_irda_ioctl(struct net_device *dev, struct ifreq *ifreq, int cmd) +{ + struct if_irda_req *rq = (struct if_irda_req *)ifreq; + struct sa1100_irda *si = netdev_priv(dev); + int ret = -EOPNOTSUPP; + + switch (cmd) { + case SIOCSBANDWIDTH: + if (capable(CAP_NET_ADMIN)) { + /* + * We are unable to set the speed if the + * device is not running. + */ + if (si->open) { + ret = sa1100_irda_set_speed(si, + rq->ifr_baudrate); + } else { + printk("sa1100_irda_ioctl: SIOCSBANDWIDTH: !netif_running\n"); + ret = 0; + } + } + break; + + case SIOCSMEDIABUSY: + ret = -EPERM; + if (capable(CAP_NET_ADMIN)) { + irda_device_set_media_busy(dev, TRUE); + ret = 0; + } + break; + + case SIOCGRECEIVING: + rq->ifr_receiving = IS_FIR(si) ? 0 + : si->rx_buff.state != OUTSIDE_FRAME; + break; + + default: + break; + } + + return ret; +} + +static int sa1100_irda_startup(struct sa1100_irda *si) +{ + int ret; + + /* + * Ensure that the ports for this device are setup correctly. + */ + if (si->pdata->startup) { + ret = si->pdata->startup(si->dev); + if (ret) + return ret; + } + + /* + * Configure PPC for IRDA - we want to drive TXD2 low. + * We also want to drive this pin low during sleep. + */ + PPSR &= ~PPC_TXD2; + PSDR &= ~PPC_TXD2; + PPDR |= PPC_TXD2; + + /* + * Enable HP-SIR modulation, and ensure that the port is disabled. + */ + Ser2UTCR3 = 0; + Ser2HSCR0 = HSCR0_UART; + Ser2UTCR4 = si->utcr4; + Ser2UTCR0 = UTCR0_8BitData; + Ser2HSCR2 = HSCR2_TrDataH | HSCR2_RcDataL; + + /* + * Clear status register + */ + Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID; + + ret = sa1100_irda_set_speed(si, si->speed = 9600); + if (ret) { + Ser2UTCR3 = 0; + Ser2HSCR0 = 0; + + if (si->pdata->shutdown) + si->pdata->shutdown(si->dev); + } + + return ret; +} + +static void sa1100_irda_shutdown(struct sa1100_irda *si) +{ + /* + * Stop all DMA activity. + */ + dmaengine_terminate_all(si->dma_rx.chan); + dmaengine_terminate_all(si->dma_tx.chan); + + /* Disable the port. */ + Ser2UTCR3 = 0; + Ser2HSCR0 = 0; + + if (si->pdata->shutdown) + si->pdata->shutdown(si->dev); +} + +static int sa1100_irda_start(struct net_device *dev) +{ + struct sa1100_irda *si = netdev_priv(dev); + int err; + + si->speed = 9600; + + err = sa1100_irda_dma_request(si->dev, &si->dma_rx, "Ser2ICPRc", + &sa1100_irda_fir_rx); + if (err) + goto err_rx_dma; + + err = sa1100_irda_dma_request(si->dev, &si->dma_tx, "Ser2ICPTr", + &sa1100_irda_sir_tx); + if (err) + goto err_tx_dma; + + /* + * Setup the serial port for the specified speed. + */ + err = sa1100_irda_startup(si); + if (err) + goto err_startup; + + /* + * Open a new IrLAP layer instance. + */ + si->irlap = irlap_open(dev, &si->qos, "sa1100"); + err = -ENOMEM; + if (!si->irlap) + goto err_irlap; + + err = request_irq(dev->irq, sa1100_irda_irq, 0, dev->name, dev); + if (err) + goto err_irq; + + /* + * Now enable the interrupt and start the queue + */ + si->open = 1; + sa1100_set_power(si, power_level); /* low power mode */ + + netif_start_queue(dev); + return 0; + +err_irq: + irlap_close(si->irlap); +err_irlap: + si->open = 0; + sa1100_irda_shutdown(si); +err_startup: + dma_release_channel(si->dma_tx.chan); +err_tx_dma: + dma_release_channel(si->dma_rx.chan); +err_rx_dma: + return err; +} + +static int sa1100_irda_stop(struct net_device *dev) +{ + struct sa1100_irda *si = netdev_priv(dev); + struct sk_buff *skb; + + netif_stop_queue(dev); + + si->open = 0; + sa1100_irda_shutdown(si); + + /* + * If we have been doing any DMA activity, make sure we + * tidy that up cleanly. + */ + skb = si->dma_rx.skb; + if (skb) { + dma_unmap_sg(si->dma_rx.dev, &si->dma_rx.sg, 1, + DMA_FROM_DEVICE); + dev_kfree_skb(skb); + si->dma_rx.skb = NULL; + } + + skb = si->dma_tx.skb; + if (skb) { + dma_unmap_sg(si->dma_tx.dev, &si->dma_tx.sg, 1, + DMA_TO_DEVICE); + dev_kfree_skb(skb); + si->dma_tx.skb = NULL; + } + + /* Stop IrLAP */ + if (si->irlap) { + irlap_close(si->irlap); + si->irlap = NULL; + } + + /* + * Free resources + */ + dma_release_channel(si->dma_tx.chan); + dma_release_channel(si->dma_rx.chan); + free_irq(dev->irq, dev); + + sa1100_set_power(si, 0); + + return 0; +} + +static int sa1100_irda_init_iobuf(iobuff_t *io, int size) +{ + io->head = kmalloc(size, GFP_KERNEL | GFP_DMA); + if (io->head != NULL) { + io->truesize = size; + io->in_frame = FALSE; + io->state = OUTSIDE_FRAME; + io->data = io->head; + } + return io->head ? 0 : -ENOMEM; +} + +static const struct net_device_ops sa1100_irda_netdev_ops = { + .ndo_open = sa1100_irda_start, + .ndo_stop = sa1100_irda_stop, + .ndo_start_xmit = sa1100_irda_hard_xmit, + .ndo_do_ioctl = sa1100_irda_ioctl, +}; + +static int sa1100_irda_probe(struct platform_device *pdev) +{ + struct net_device *dev; + struct sa1100_irda *si; + unsigned int baudrate_mask; + int err, irq; + + if (!pdev->dev.platform_data) + return -EINVAL; + + irq = platform_get_irq(pdev, 0); + if (irq <= 0) + return irq < 0 ? irq : -ENXIO; + + err = request_mem_region(__PREG(Ser2UTCR0), 0x24, "IrDA") ? 0 : -EBUSY; + if (err) + goto err_mem_1; + err = request_mem_region(__PREG(Ser2HSCR0), 0x1c, "IrDA") ? 0 : -EBUSY; + if (err) + goto err_mem_2; + err = request_mem_region(__PREG(Ser2HSCR2), 0x04, "IrDA") ? 0 : -EBUSY; + if (err) + goto err_mem_3; + + dev = alloc_irdadev(sizeof(struct sa1100_irda)); + if (!dev) { + err = -ENOMEM; + goto err_mem_4; + } + + SET_NETDEV_DEV(dev, &pdev->dev); + + si = netdev_priv(dev); + si->dev = &pdev->dev; + si->pdata = pdev->dev.platform_data; + + sg_init_table(&si->dma_rx.sg, 1); + sg_init_table(&si->dma_tx.sg, 1); + + /* + * Initialise the HP-SIR buffers + */ + err = sa1100_irda_init_iobuf(&si->rx_buff, 14384); + if (err) + goto err_mem_5; + err = sa1100_irda_init_iobuf(&si->tx_buff, IRDA_SIR_MAX_FRAME); + if (err) + goto err_mem_5; + + dev->netdev_ops = &sa1100_irda_netdev_ops; + dev->irq = irq; + + irda_init_max_qos_capabilies(&si->qos); + + /* + * We support original IRDA up to 115k2. (we don't currently + * support 4Mbps). Min Turn Time set to 1ms or greater. + */ + baudrate_mask = IR_9600; + + switch (max_rate) { + case 4000000: baudrate_mask |= IR_4000000 << 8; + case 115200: baudrate_mask |= IR_115200; + case 57600: baudrate_mask |= IR_57600; + case 38400: baudrate_mask |= IR_38400; + case 19200: baudrate_mask |= IR_19200; + } + + si->qos.baud_rate.bits &= baudrate_mask; + si->qos.min_turn_time.bits = 7; + + irda_qos_bits_to_value(&si->qos); + + si->utcr4 = UTCR4_HPSIR; + if (tx_lpm) + si->utcr4 |= UTCR4_Z1_6us; + + /* + * Initially enable HP-SIR modulation, and ensure that the port + * is disabled. + */ + Ser2UTCR3 = 0; + Ser2UTCR4 = si->utcr4; + Ser2HSCR0 = HSCR0_UART; + + err = register_netdev(dev); + if (err == 0) + platform_set_drvdata(pdev, dev); + + if (err) { + err_mem_5: + kfree(si->tx_buff.head); + kfree(si->rx_buff.head); + free_netdev(dev); + err_mem_4: + release_mem_region(__PREG(Ser2HSCR2), 0x04); + err_mem_3: + release_mem_region(__PREG(Ser2HSCR0), 0x1c); + err_mem_2: + release_mem_region(__PREG(Ser2UTCR0), 0x24); + } + err_mem_1: + return err; +} + +static int sa1100_irda_remove(struct platform_device *pdev) +{ + struct net_device *dev = platform_get_drvdata(pdev); + + if (dev) { + struct sa1100_irda *si = netdev_priv(dev); + unregister_netdev(dev); + kfree(si->tx_buff.head); + kfree(si->rx_buff.head); + free_netdev(dev); + } + + release_mem_region(__PREG(Ser2HSCR2), 0x04); + release_mem_region(__PREG(Ser2HSCR0), 0x1c); + release_mem_region(__PREG(Ser2UTCR0), 0x24); + + return 0; +} + +#ifdef CONFIG_PM +/* + * Suspend the IrDA interface. + */ +static int sa1100_irda_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct net_device *dev = platform_get_drvdata(pdev); + struct sa1100_irda *si; + + if (!dev) + return 0; + + si = netdev_priv(dev); + if (si->open) { + /* + * Stop the transmit queue + */ + netif_device_detach(dev); + disable_irq(dev->irq); + sa1100_irda_shutdown(si); + __sa1100_irda_set_power(si, 0); + } + + return 0; +} + +/* + * Resume the IrDA interface. + */ +static int sa1100_irda_resume(struct platform_device *pdev) +{ + struct net_device *dev = platform_get_drvdata(pdev); + struct sa1100_irda *si; + + if (!dev) + return 0; + + si = netdev_priv(dev); + if (si->open) { + /* + * If we missed a speed change, initialise at the new speed + * directly. It is debatable whether this is actually + * required, but in the interests of continuing from where + * we left off it is desirable. The converse argument is + * that we should re-negotiate at 9600 baud again. + */ + if (si->newspeed) { + si->speed = si->newspeed; + si->newspeed = 0; + } + + sa1100_irda_startup(si); + __sa1100_irda_set_power(si, si->power); + enable_irq(dev->irq); + + /* + * This automatically wakes up the queue + */ + netif_device_attach(dev); + } + + return 0; +} +#else +#define sa1100_irda_suspend NULL +#define sa1100_irda_resume NULL +#endif + +static struct platform_driver sa1100ir_driver = { + .probe = sa1100_irda_probe, + .remove = sa1100_irda_remove, + .suspend = sa1100_irda_suspend, + .resume = sa1100_irda_resume, + .driver = { + .name = "sa11x0-ir", + }, +}; + +static int __init sa1100_irda_init(void) +{ + /* + * Limit power level a sensible range. + */ + if (power_level < 1) + power_level = 1; + if (power_level > 3) + power_level = 3; + + return platform_driver_register(&sa1100ir_driver); +} + +static void __exit sa1100_irda_exit(void) +{ + platform_driver_unregister(&sa1100ir_driver); +} + +module_init(sa1100_irda_init); +module_exit(sa1100_irda_exit); +module_param(power_level, int, 0); +module_param(tx_lpm, int, 0); +module_param(max_rate, int, 0); + +MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>"); +MODULE_DESCRIPTION("StrongARM SA1100 IrDA driver"); +MODULE_LICENSE("GPL"); +MODULE_PARM_DESC(power_level, "IrDA power level, 1 (low) to 3 (high)"); +MODULE_PARM_DESC(tx_lpm, "Enable transmitter low power (1.6us) mode"); +MODULE_PARM_DESC(max_rate, "Maximum baud rate (4000000, 115200, 57600, 38400, 19200, 9600)"); +MODULE_ALIAS("platform:sa11x0-ir"); |