diff options
Diffstat (limited to 'drivers/staging/rdma/ipath/ipath_eeprom.c')
| -rw-r--r-- | drivers/staging/rdma/ipath/ipath_eeprom.c | 1183 |
1 files changed, 1183 insertions, 0 deletions
diff --git a/drivers/staging/rdma/ipath/ipath_eeprom.c b/drivers/staging/rdma/ipath/ipath_eeprom.c new file mode 100644 index 000000000000..fc7181985e8e --- /dev/null +++ b/drivers/staging/rdma/ipath/ipath_eeprom.c @@ -0,0 +1,1183 @@ +/* + * Copyright (c) 2006, 2007, 2008 QLogic Corporation. All rights reserved. + * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. + * + * This software is available to you under a choice of one of two + * licenses. You may choose to be licensed under the terms of the GNU + * General Public License (GPL) Version 2, available from the file + * COPYING in the main directory of this source tree, or the + * OpenIB.org BSD license below: + * + * Redistribution and use in source and binary forms, with or + * without modification, are permitted provided that the following + * conditions are met: + * + * - Redistributions of source code must retain the above + * copyright notice, this list of conditions and the following + * disclaimer. + * + * - Redistributions in binary form must reproduce the above + * copyright notice, this list of conditions and the following + * disclaimer in the documentation and/or other materials + * provided with the distribution. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS + * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN + * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE + * SOFTWARE. + */ + +#include <linux/delay.h> +#include <linux/pci.h> +#include <linux/vmalloc.h> + +#include "ipath_kernel.h" + +/* + * InfiniPath I2C driver for a serial eeprom. This is not a generic + * I2C interface. For a start, the device we're using (Atmel AT24C11) + * doesn't work like a regular I2C device. It looks like one + * electrically, but not logically. Normal I2C devices have a single + * 7-bit or 10-bit I2C address that they respond to. Valid 7-bit + * addresses range from 0x03 to 0x77. Addresses 0x00 to 0x02 and 0x78 + * to 0x7F are special reserved addresses (e.g. 0x00 is the "general + * call" address.) The Atmel device, on the other hand, responds to ALL + * 7-bit addresses. It's designed to be the only device on a given I2C + * bus. A 7-bit address corresponds to the memory address within the + * Atmel device itself. + * + * Also, the timing requirements mean more than simple software + * bitbanging, with readbacks from chip to ensure timing (simple udelay + * is not enough). + * + * This all means that accessing the device is specialized enough + * that using the standard kernel I2C bitbanging interface would be + * impossible. For example, the core I2C eeprom driver expects to find + * a device at one or more of a limited set of addresses only. It doesn't + * allow writing to an eeprom. It also doesn't provide any means of + * accessing eeprom contents from within the kernel, only via sysfs. + */ + +/* Added functionality for IBA7220-based cards */ +#define IPATH_EEPROM_DEV_V1 0xA0 +#define IPATH_EEPROM_DEV_V2 0xA2 +#define IPATH_TEMP_DEV 0x98 +#define IPATH_BAD_DEV (IPATH_EEPROM_DEV_V2+2) +#define IPATH_NO_DEV (0xFF) + +/* + * The number of I2C chains is proliferating. Table below brings + * some order to the madness. The basic principle is that the + * table is scanned from the top, and a "probe" is made to the + * device probe_dev. If that succeeds, the chain is considered + * to be of that type, and dd->i2c_chain_type is set to the index+1 + * of the entry. + * The +1 is so static initialization can mean "unknown, do probe." + */ +static struct i2c_chain_desc { + u8 probe_dev; /* If seen at probe, chain is this type */ + u8 eeprom_dev; /* Dev addr (if any) for EEPROM */ + u8 temp_dev; /* Dev Addr (if any) for Temp-sense */ +} i2c_chains[] = { + { IPATH_BAD_DEV, IPATH_NO_DEV, IPATH_NO_DEV }, /* pre-iba7220 bds */ + { IPATH_EEPROM_DEV_V1, IPATH_EEPROM_DEV_V1, IPATH_TEMP_DEV}, /* V1 */ + { IPATH_EEPROM_DEV_V2, IPATH_EEPROM_DEV_V2, IPATH_TEMP_DEV}, /* V2 */ + { IPATH_NO_DEV } +}; + +enum i2c_type { + i2c_line_scl = 0, + i2c_line_sda +}; + +enum i2c_state { + i2c_line_low = 0, + i2c_line_high +}; + +#define READ_CMD 1 +#define WRITE_CMD 0 + +/** + * i2c_gpio_set - set a GPIO line + * @dd: the infinipath device + * @line: the line to set + * @new_line_state: the state to set + * + * Returns 0 if the line was set to the new state successfully, non-zero + * on error. + */ +static int i2c_gpio_set(struct ipath_devdata *dd, + enum i2c_type line, + enum i2c_state new_line_state) +{ + u64 out_mask, dir_mask, *gpioval; + unsigned long flags = 0; + + gpioval = &dd->ipath_gpio_out; + + if (line == i2c_line_scl) { + dir_mask = dd->ipath_gpio_scl; + out_mask = (1UL << dd->ipath_gpio_scl_num); + } else { + dir_mask = dd->ipath_gpio_sda; + out_mask = (1UL << dd->ipath_gpio_sda_num); + } + + spin_lock_irqsave(&dd->ipath_gpio_lock, flags); + if (new_line_state == i2c_line_high) { + /* tri-state the output rather than force high */ + dd->ipath_extctrl &= ~dir_mask; + } else { + /* config line to be an output */ + dd->ipath_extctrl |= dir_mask; + } + ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, dd->ipath_extctrl); + + /* set output as well (no real verify) */ + if (new_line_state == i2c_line_high) + *gpioval |= out_mask; + else + *gpioval &= ~out_mask; + + ipath_write_kreg(dd, dd->ipath_kregs->kr_gpio_out, *gpioval); + spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags); + + return 0; +} + +/** + * i2c_gpio_get - get a GPIO line state + * @dd: the infinipath device + * @line: the line to get + * @curr_statep: where to put the line state + * + * Returns 0 if the line was set to the new state successfully, non-zero + * on error. curr_state is not set on error. + */ +static int i2c_gpio_get(struct ipath_devdata *dd, + enum i2c_type line, + enum i2c_state *curr_statep) +{ + u64 read_val, mask; + int ret; + unsigned long flags = 0; + + /* check args */ + if (curr_statep == NULL) { + ret = 1; + goto bail; + } + + /* config line to be an input */ + if (line == i2c_line_scl) + mask = dd->ipath_gpio_scl; + else + mask = dd->ipath_gpio_sda; + + spin_lock_irqsave(&dd->ipath_gpio_lock, flags); + dd->ipath_extctrl &= ~mask; + ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, dd->ipath_extctrl); + /* + * Below is very unlikely to reflect true input state if Output + * Enable actually changed. + */ + read_val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus); + spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags); + + if (read_val & mask) + *curr_statep = i2c_line_high; + else + *curr_statep = i2c_line_low; + + ret = 0; + +bail: + return ret; +} + +/** + * i2c_wait_for_writes - wait for a write + * @dd: the infinipath device + * + * We use this instead of udelay directly, so we can make sure + * that previous register writes have been flushed all the way + * to the chip. Since we are delaying anyway, the cost doesn't + * hurt, and makes the bit twiddling more regular + */ +static void i2c_wait_for_writes(struct ipath_devdata *dd) +{ + (void)ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); + rmb(); +} + +static void scl_out(struct ipath_devdata *dd, u8 bit) +{ + udelay(1); + i2c_gpio_set(dd, i2c_line_scl, bit ? i2c_line_high : i2c_line_low); + + i2c_wait_for_writes(dd); +} + +static void sda_out(struct ipath_devdata *dd, u8 bit) +{ + i2c_gpio_set(dd, i2c_line_sda, bit ? i2c_line_high : i2c_line_low); + + i2c_wait_for_writes(dd); +} + +static u8 sda_in(struct ipath_devdata *dd, int wait) +{ + enum i2c_state bit; + + if (i2c_gpio_get(dd, i2c_line_sda, &bit)) + ipath_dbg("get bit failed!\n"); + + if (wait) + i2c_wait_for_writes(dd); + + return bit == i2c_line_high ? 1U : 0; +} + +/** + * i2c_ackrcv - see if ack following write is true + * @dd: the infinipath device + */ +static int i2c_ackrcv(struct ipath_devdata *dd) +{ + u8 ack_received; + + /* AT ENTRY SCL = LOW */ + /* change direction, ignore data */ + ack_received = sda_in(dd, 1); + scl_out(dd, i2c_line_high); + ack_received = sda_in(dd, 1) == 0; + scl_out(dd, i2c_line_low); + return ack_received; +} + +/** + * rd_byte - read a byte, leaving ACK, STOP, etc up to caller + * @dd: the infinipath device + * + * Returns byte shifted out of device + */ +static int rd_byte(struct ipath_devdata *dd) +{ + int bit_cntr, data; + + data = 0; + + for (bit_cntr = 7; bit_cntr >= 0; --bit_cntr) { + data <<= 1; + scl_out(dd, i2c_line_high); + data |= sda_in(dd, 0); + scl_out(dd, i2c_line_low); + } + return data; +} + +/** + * wr_byte - write a byte, one bit at a time + * @dd: the infinipath device + * @data: the byte to write + * + * Returns 0 if we got the following ack, otherwise 1 + */ +static int wr_byte(struct ipath_devdata *dd, u8 data) +{ + int bit_cntr; + u8 bit; + + for (bit_cntr = 7; bit_cntr >= 0; bit_cntr--) { + bit = (data >> bit_cntr) & 1; + sda_out(dd, bit); + scl_out(dd, i2c_line_high); + scl_out(dd, i2c_line_low); + } + return (!i2c_ackrcv(dd)) ? 1 : 0; +} + +static void send_ack(struct ipath_devdata *dd) +{ + sda_out(dd, i2c_line_low); + scl_out(dd, i2c_line_high); + scl_out(dd, i2c_line_low); + sda_out(dd, i2c_line_high); +} + +/** + * i2c_startcmd - transmit the start condition, followed by address/cmd + * @dd: the infinipath device + * @offset_dir: direction byte + * + * (both clock/data high, clock high, data low while clock is high) + */ +static int i2c_startcmd(struct ipath_devdata *dd, u8 offset_dir) +{ + int res; + + /* issue start sequence */ + sda_out(dd, i2c_line_high); + scl_out(dd, i2c_line_high); + sda_out(dd, i2c_line_low); + scl_out(dd, i2c_line_low); + + /* issue length and direction byte */ + res = wr_byte(dd, offset_dir); + + if (res) + ipath_cdbg(VERBOSE, "No ack to complete start\n"); + + return res; +} + +/** + * stop_cmd - transmit the stop condition + * @dd: the infinipath device + * + * (both clock/data low, clock high, data high while clock is high) + */ +static void stop_cmd(struct ipath_devdata *dd) +{ + scl_out(dd, i2c_line_low); + sda_out(dd, i2c_line_low); + scl_out(dd, i2c_line_high); + sda_out(dd, i2c_line_high); + udelay(2); +} + +/** + * eeprom_reset - reset I2C communication + * @dd: the infinipath device + */ + +static int eeprom_reset(struct ipath_devdata *dd) +{ + int clock_cycles_left = 9; + u64 *gpioval = &dd->ipath_gpio_out; + int ret; + unsigned long flags; + + spin_lock_irqsave(&dd->ipath_gpio_lock, flags); + /* Make sure shadows are consistent */ + dd->ipath_extctrl = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extctrl); + *gpioval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_gpio_out); + spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags); + + ipath_cdbg(VERBOSE, "Resetting i2c eeprom; initial gpioout reg " + "is %llx\n", (unsigned long long) *gpioval); + + /* + * This is to get the i2c into a known state, by first going low, + * then tristate sda (and then tristate scl as first thing + * in loop) + */ + scl_out(dd, i2c_line_low); + sda_out(dd, i2c_line_high); + + /* Clock up to 9 cycles looking for SDA hi, then issue START and STOP */ + while (clock_cycles_left--) { + scl_out(dd, i2c_line_high); + + /* SDA seen high, issue START by dropping it while SCL high */ + if (sda_in(dd, 0)) { + sda_out(dd, i2c_line_low); + scl_out(dd, i2c_line_low); + /* ATMEL spec says must be followed by STOP. */ + scl_out(dd, i2c_line_high); + sda_out(dd, i2c_line_high); + ret = 0; + goto bail; + } + + scl_out(dd, i2c_line_low); + } + + ret = 1; + +bail: + return ret; +} + +/* + * Probe for I2C device at specified address. Returns 0 for "success" + * to match rest of this file. + * Leave bus in "reasonable" state for further commands. + */ +static int i2c_probe(struct ipath_devdata *dd, int devaddr) +{ + int ret = 0; + + ret = eeprom_reset(dd); + if (ret) { + ipath_dev_err(dd, "Failed reset probing device 0x%02X\n", + devaddr); + return ret; + } + /* + * Reset no longer leaves bus in start condition, so normal + * i2c_startcmd() will do. + */ + ret = i2c_startcmd(dd, devaddr | READ_CMD); + if (ret) + ipath_cdbg(VERBOSE, "Failed startcmd for device 0x%02X\n", + devaddr); + else { + /* + * Device did respond. Complete a single-byte read, because some + * devices apparently cannot handle STOP immediately after they + * ACK the start-cmd. + */ + int data; + data = rd_byte(dd); + stop_cmd(dd); + ipath_cdbg(VERBOSE, "Response from device 0x%02X\n", devaddr); + } + return ret; +} + +/* + * Returns the "i2c type". This is a pointer to a struct that describes + * the I2C chain on this board. To minimize impact on struct ipath_devdata, + * the (small integer) index into the table is actually memoized, rather + * then the pointer. + * Memoization is because the type is determined on the first call per chip. + * An alternative would be to move type determination to early + * init code. + */ +static struct i2c_chain_desc *ipath_i2c_type(struct ipath_devdata *dd) +{ + int idx; + + /* Get memoized index, from previous successful probes */ + idx = dd->ipath_i2c_chain_type - 1; + if (idx >= 0 && idx < (ARRAY_SIZE(i2c_chains) - 1)) + goto done; + + idx = 0; + while (i2c_chains[idx].probe_dev != IPATH_NO_DEV) { + /* if probe succeeds, this is type */ + if (!i2c_probe(dd, i2c_chains[idx].probe_dev)) + break; + ++idx; + } + + /* + * Old EEPROM (first entry) may require a reset after probe, + * rather than being able to "start" after "stop" + */ + if (idx == 0) + eeprom_reset(dd); + + if (i2c_chains[idx].probe_dev == IPATH_NO_DEV) + idx = -1; + else + dd->ipath_i2c_chain_type = idx + 1; +done: + return (idx >= 0) ? i2c_chains + idx : NULL; +} + +static int ipath_eeprom_internal_read(struct ipath_devdata *dd, + u8 eeprom_offset, void *buffer, int len) +{ + int ret; + struct i2c_chain_desc *icd; + u8 *bp = buffer; + + ret = 1; + icd = ipath_i2c_type(dd); + if (!icd) + goto bail; + + if (icd->eeprom_dev == IPATH_NO_DEV) { + /* legacy not-really-I2C */ + ipath_cdbg(VERBOSE, "Start command only address\n"); + eeprom_offset = (eeprom_offset << 1) | READ_CMD; + ret = i2c_startcmd(dd, eeprom_offset); + } else { + /* Actual I2C */ + ipath_cdbg(VERBOSE, "Start command uses devaddr\n"); + if (i2c_startcmd(dd, icd->eeprom_dev | WRITE_CMD)) { + ipath_dbg("Failed EEPROM startcmd\n"); + stop_cmd(dd); + ret = 1; + goto bail; + } + ret = wr_byte(dd, eeprom_offset); + stop_cmd(dd); + if (ret) { + ipath_dev_err(dd, "Failed to write EEPROM address\n"); + ret = 1; + goto bail; + } + ret = i2c_startcmd(dd, icd->eeprom_dev | READ_CMD); + } + if (ret) { + ipath_dbg("Failed startcmd for dev %02X\n", icd->eeprom_dev); + stop_cmd(dd); + ret = 1; + goto bail; + } + + /* + * eeprom keeps clocking data out as long as we ack, automatically + * incrementing the address. + */ + while (len-- > 0) { + /* get and store data */ + *bp++ = rd_byte(dd); + /* send ack if not the last byte */ + if (len) + send_ack(dd); + } + + stop_cmd(dd); + + ret = 0; + +bail: + return ret; +} + +static int ipath_eeprom_internal_write(struct ipath_devdata *dd, u8 eeprom_offset, + const void *buffer, int len) +{ + int sub_len; + const u8 *bp = buffer; + int max_wait_time, i; + int ret; + struct i2c_chain_desc *icd; + + ret = 1; + icd = ipath_i2c_type(dd); + if (!icd) + goto bail; + + while (len > 0) { + if (icd->eeprom_dev == IPATH_NO_DEV) { + if (i2c_startcmd(dd, + (eeprom_offset << 1) | WRITE_CMD)) { + ipath_dbg("Failed to start cmd offset %u\n", + eeprom_offset); + goto failed_write; + } + } else { + /* Real I2C */ + if (i2c_startcmd(dd, icd->eeprom_dev | WRITE_CMD)) { + ipath_dbg("Failed EEPROM startcmd\n"); + goto failed_write; + } + ret = wr_byte(dd, eeprom_offset); + if (ret) { + ipath_dev_err(dd, "Failed to write EEPROM " + "address\n"); + goto failed_write; + } + } + + sub_len = min(len, 4); + eeprom_offset += sub_len; + len -= sub_len; + + for (i = 0; i < sub_len; i++) { + if (wr_byte(dd, *bp++)) { + ipath_dbg("no ack after byte %u/%u (%u " + "total remain)\n", i, sub_len, + len + sub_len - i); + goto failed_write; + } + } + + stop_cmd(dd); + + /* + * wait for write complete by waiting for a successful + * read (the chip replies with a zero after the write + * cmd completes, and before it writes to the eeprom. + * The startcmd for the read will fail the ack until + * the writes have completed. We do this inline to avoid + * the debug prints that are in the real read routine + * if the startcmd fails. + * We also use the proper device address, so it doesn't matter + * whether we have real eeprom_dev. legacy likes any address. + */ + max_wait_time = 100; + while (i2c_startcmd(dd, icd->eeprom_dev | READ_CMD)) { + stop_cmd(dd); + if (!--max_wait_time) { + ipath_dbg("Did not get successful read to " + "complete write\n"); + goto failed_write; + } + } + /* now read (and ignore) the resulting byte */ + rd_byte(dd); + stop_cmd(dd); + } + + ret = 0; + goto bail; + +failed_write: + stop_cmd(dd); + ret = 1; + +bail: + return ret; +} + +/** + * ipath_eeprom_read - receives bytes from the eeprom via I2C + * @dd: the infinipath device + * @eeprom_offset: address to read from + * @buffer: where to store result + * @len: number of bytes to receive + */ +int ipath_eeprom_read(struct ipath_devdata *dd, u8 eeprom_offset, + void *buff, int len) +{ + int ret; + + ret = mutex_lock_interruptible(&dd->ipath_eep_lock); + if (!ret) { + ret = ipath_eeprom_internal_read(dd, eeprom_offset, buff, len); + mutex_unlock(&dd->ipath_eep_lock); + } + + return ret; +} + +/** + * ipath_eeprom_write - writes data to the eeprom via I2C + * @dd: the infinipath device + * @eeprom_offset: where to place data + * @buffer: data to write + * @len: number of bytes to write + */ +int ipath_eeprom_write(struct ipath_devdata *dd, u8 eeprom_offset, + const void *buff, int len) +{ + int ret; + + ret = mutex_lock_interruptible(&dd->ipath_eep_lock); + if (!ret) { + ret = ipath_eeprom_internal_write(dd, eeprom_offset, buff, len); + mutex_unlock(&dd->ipath_eep_lock); + } + + return ret; +} + +static u8 flash_csum(struct ipath_flash *ifp, int adjust) +{ + u8 *ip = (u8 *) ifp; + u8 csum = 0, len; + + /* + * Limit length checksummed to max length of actual data. + * Checksum of erased eeprom will still be bad, but we avoid + * reading past the end of the buffer we were passed. + */ + len = ifp->if_length; + if (len > sizeof(struct ipath_flash)) + len = sizeof(struct ipath_flash); + while (len--) + csum += *ip++; + csum -= ifp->if_csum; + csum = ~csum; + if (adjust) + ifp->if_csum = csum; + + return csum; +} + +/** + * ipath_get_guid - get the GUID from the i2c device + * @dd: the infinipath device + * + * We have the capability to use the ipath_nguid field, and get + * the guid from the first chip's flash, to use for all of them. + */ +void ipath_get_eeprom_info(struct ipath_devdata *dd) +{ + void *buf; + struct ipath_flash *ifp; + __be64 guid; + int len, eep_stat; + u8 csum, *bguid; + int t = dd->ipath_unit; + struct ipath_devdata *dd0 = ipath_lookup(0); + + if (t && dd0->ipath_nguid > 1 && t <= dd0->ipath_nguid) { + u8 oguid; + dd->ipath_guid = dd0->ipath_guid; + bguid = (u8 *) & dd->ipath_guid; + + oguid = bguid[7]; + bguid[7] += t; + if (oguid > bguid[7]) { + if (bguid[6] == 0xff) { + if (bguid[5] == 0xff) { + ipath_dev_err( + dd, + "Can't set %s GUID from " + "base, wraps to OUI!\n", + ipath_get_unit_name(t)); + dd->ipath_guid = 0; + goto bail; + } + bguid[5]++; + } + bguid[6]++; + } + dd->ipath_nguid = 1; + + ipath_dbg("nguid %u, so adding %u to device 0 guid, " + "for %llx\n", + dd0->ipath_nguid, t, + (unsigned long long) be64_to_cpu(dd->ipath_guid)); + goto bail; + } + + /* + * read full flash, not just currently used part, since it may have + * been written with a newer definition + * */ + len = sizeof(struct ipath_flash); + buf = vmalloc(len); + if (!buf) { + ipath_dev_err(dd, "Couldn't allocate memory to read %u " + "bytes from eeprom for GUID\n", len); + goto bail; + } + + mutex_lock(&dd->ipath_eep_lock); + eep_stat = ipath_eeprom_internal_read(dd, 0, buf, len); + mutex_unlock(&dd->ipath_eep_lock); + + if (eep_stat) { + ipath_dev_err(dd, "Failed reading GUID from eeprom\n"); + goto done; + } + ifp = (struct ipath_flash *)buf; + + csum = flash_csum(ifp, 0); + if (csum != ifp->if_csum) { + dev_info(&dd->pcidev->dev, "Bad I2C flash checksum: " + "0x%x, not 0x%x\n", csum, ifp->if_csum); + goto done; + } + if (*(__be64 *) ifp->if_guid == cpu_to_be64(0) || + *(__be64 *) ifp->if_guid == ~cpu_to_be64(0)) { + ipath_dev_err(dd, "Invalid GUID %llx from flash; " + "ignoring\n", + *(unsigned long long *) ifp->if_guid); + /* don't allow GUID if all 0 or all 1's */ + goto done; + } + + /* complain, but allow it */ + if (*(u64 *) ifp->if_guid == 0x100007511000000ULL) + dev_info(&dd->pcidev->dev, "Warning, GUID %llx is " + "default, probably not correct!\n", + *(unsigned long long *) ifp->if_guid); + + bguid = ifp->if_guid; + if (!bguid[0] && !bguid[1] && !bguid[2]) { + /* original incorrect GUID format in flash; fix in + * core copy, by shifting up 2 octets; don't need to + * change top octet, since both it and shifted are + * 0.. */ + bguid[1] = bguid[3]; + bguid[2] = bguid[4]; + bguid[3] = bguid[4] = 0; + guid = *(__be64 *) ifp->if_guid; + ipath_cdbg(VERBOSE, "Old GUID format in flash, top 3 zero, " + "shifting 2 octets\n"); + } else + guid = *(__be64 *) ifp->if_guid; + dd->ipath_guid = guid; + dd->ipath_nguid = ifp->if_numguid; + /* + * Things are slightly complicated by the desire to transparently + * support both the Pathscale 10-digit serial number and the QLogic + * 13-character version. + */ + if ((ifp->if_fversion > 1) && ifp->if_sprefix[0] + && ((u8 *)ifp->if_sprefix)[0] != 0xFF) { + /* This board has a Serial-prefix, which is stored + * elsewhere for backward-compatibility. + */ + char *snp = dd->ipath_serial; + memcpy(snp, ifp->if_sprefix, sizeof ifp->if_sprefix); + snp[sizeof ifp->if_sprefix] = '\0'; + len = strlen(snp); + snp += len; + len = (sizeof dd->ipath_serial) - len; + if (len > sizeof ifp->if_serial) { + len = sizeof ifp->if_serial; + } + memcpy(snp, ifp->if_serial, len); + } else + memcpy(dd->ipath_serial, ifp->if_serial, + sizeof ifp->if_serial); + if (!strstr(ifp->if_comment, "Tested successfully")) + ipath_dev_err(dd, "Board SN %s did not pass functional " + "test: %s\n", dd->ipath_serial, + ifp->if_comment); + + ipath_cdbg(VERBOSE, "Initted GUID to %llx from eeprom\n", + (unsigned long long) be64_to_cpu(dd->ipath_guid)); + + memcpy(&dd->ipath_eep_st_errs, &ifp->if_errcntp, IPATH_EEP_LOG_CNT); + /* + * Power-on (actually "active") hours are kept as little-endian value + * in EEPROM, but as seconds in a (possibly as small as 24-bit) + * atomic_t while running. + */ + atomic_set(&dd->ipath_active_time, 0); + dd->ipath_eep_hrs = ifp->if_powerhour[0] | (ifp->if_powerhour[1] << 8); + +done: + vfree(buf); + +bail:; +} + +/** + * ipath_update_eeprom_log - copy active-time and error counters to eeprom + * @dd: the infinipath device + * + * Although the time is kept as seconds in the ipath_devdata struct, it is + * rounded to hours for re-write, as we have only 16 bits in EEPROM. + * First-cut code reads whole (expected) struct ipath_flash, modifies, + * re-writes. Future direction: read/write only what we need, assuming + * that the EEPROM had to have been "good enough" for driver init, and + * if not, we aren't making it worse. + * + */ + +int ipath_update_eeprom_log(struct ipath_devdata *dd) +{ + void *buf; + struct ipath_flash *ifp; + int len, hi_water; + uint32_t new_time, new_hrs; + u8 csum; + int ret, idx; + unsigned long flags; + + /* first, check if we actually need to do anything. */ + ret = 0; + for (idx = 0; idx < IPATH_EEP_LOG_CNT; ++idx) { + if (dd->ipath_eep_st_new_errs[idx]) { + ret = 1; + break; + } + } + new_time = atomic_read(&dd->ipath_active_time); + + if (ret == 0 && new_time < 3600) + return 0; + + /* + * The quick-check above determined that there is something worthy + * of logging, so get current contents and do a more detailed idea. + * read full flash, not just currently used part, since it may have + * been written with a newer definition + */ + len = sizeof(struct ipath_flash); + buf = vmalloc(len); + ret = 1; + if (!buf) { + ipath_dev_err(dd, "Couldn't allocate memory to read %u " + "bytes from eeprom for logging\n", len); + goto bail; + } + + /* Grab semaphore and read current EEPROM. If we get an + * error, let go, but if not, keep it until we finish write. + */ + ret = mutex_lock_interruptible(&dd->ipath_eep_lock); + if (ret) { + ipath_dev_err(dd, "Unable to acquire EEPROM for logging\n"); + goto free_bail; + } + ret = ipath_eeprom_internal_read(dd, 0, buf, len); + if (ret) { + mutex_unlock(&dd->ipath_eep_lock); + ipath_dev_err(dd, "Unable read EEPROM for logging\n"); + goto free_bail; + } + ifp = (struct ipath_flash *)buf; + + csum = flash_csum(ifp, 0); + if (csum != ifp->if_csum) { + mutex_unlock(&dd->ipath_eep_lock); + ipath_dev_err(dd, "EEPROM cks err (0x%02X, S/B 0x%02X)\n", + csum, ifp->if_csum); + ret = 1; + goto free_bail; + } + hi_water = 0; + spin_lock_irqsave(&dd->ipath_eep_st_lock, flags); + for (idx = 0; idx < IPATH_EEP_LOG_CNT; ++idx) { + int new_val = dd->ipath_eep_st_new_errs[idx]; + if (new_val) { + /* + * If we have seen any errors, add to EEPROM values + * We need to saturate at 0xFF (255) and we also + * would need to adjust the checksum if we were + * trying to minimize EEPROM traffic + * Note that we add to actual current count in EEPROM, + * in case it was altered while we were running. + */ + new_val += ifp->if_errcntp[idx]; + if (new_val > 0xFF) + new_val = 0xFF; + if (ifp->if_errcntp[idx] != new_val) { + ifp->if_errcntp[idx] = new_val; + hi_water = offsetof(struct ipath_flash, + if_errcntp) + idx; + } + /* + * update our shadow (used to minimize EEPROM + * traffic), to match what we are about to write. + */ + dd->ipath_eep_st_errs[idx] = new_val; + dd->ipath_eep_st_new_errs[idx] = 0; + } + } + /* + * now update active-time. We would like to round to the nearest hour + * but unless atomic_t are sure to be proper signed ints we cannot, + * because we need to account for what we "transfer" to EEPROM and + * if we log an hour at 31 minutes, then we would need to set + * active_time to -29 to accurately count the _next_ hour. + */ + if (new_time >= 3600) { + new_hrs = new_time / 3600; + atomic_sub((new_hrs * 3600), &dd->ipath_active_time); + new_hrs += dd->ipath_eep_hrs; + if (new_hrs > 0xFFFF) + new_hrs = 0xFFFF; + dd->ipath_eep_hrs = new_hrs; + if ((new_hrs & 0xFF) != ifp->if_powerhour[0]) { + ifp->if_powerhour[0] = new_hrs & 0xFF; + hi_water = offsetof(struct ipath_flash, if_powerhour); + } + if ((new_hrs >> 8) != ifp->if_powerhour[1]) { + ifp->if_powerhour[1] = new_hrs >> 8; + hi_water = offsetof(struct ipath_flash, if_powerhour) + + 1; + } + } + /* + * There is a tiny possibility that we could somehow fail to write + * the EEPROM after updating our shadows, but problems from holding + * the spinlock too long are a much bigger issue. + */ + spin_unlock_irqrestore(&dd->ipath_eep_st_lock, flags); + if (hi_water) { + /* we made some change to the data, uopdate cksum and write */ + csum = flash_csum(ifp, 1); + ret = ipath_eeprom_internal_write(dd, 0, buf, hi_water + 1); + } + mutex_unlock(&dd->ipath_eep_lock); + if (ret) + ipath_dev_err(dd, "Failed updating EEPROM\n"); + +free_bail: + vfree(buf); +bail: + return ret; + +} + +/** + * ipath_inc_eeprom_err - increment one of the four error counters + * that are logged to EEPROM. + * @dd: the infinipath device + * @eidx: 0..3, the counter to increment + * @incr: how much to add + * + * Each counter is 8-bits, and saturates at 255 (0xFF). They + * are copied to the EEPROM (aka flash) whenever ipath_update_eeprom_log() + * is called, but it can only be called in a context that allows sleep. + * This function can be called even at interrupt level. + */ + +void ipath_inc_eeprom_err(struct ipath_devdata *dd, u32 eidx, u32 incr) +{ + uint new_val; + unsigned long flags; + + spin_lock_irqsave(&dd->ipath_eep_st_lock, flags); + new_val = dd->ipath_eep_st_new_errs[eidx] + incr; + if (new_val > 255) + new_val = 255; + dd->ipath_eep_st_new_errs[eidx] = new_val; + spin_unlock_irqrestore(&dd->ipath_eep_st_lock, flags); + return; +} + +static int ipath_tempsense_internal_read(struct ipath_devdata *dd, u8 regnum) +{ + int ret; + struct i2c_chain_desc *icd; + + ret = -ENOENT; + + icd = ipath_i2c_type(dd); + if (!icd) + goto bail; + + if (icd->temp_dev == IPATH_NO_DEV) { + /* tempsense only exists on new, real-I2C boards */ + ret = -ENXIO; + goto bail; + } + + if (i2c_startcmd(dd, icd->temp_dev | WRITE_CMD)) { + ipath_dbg("Failed tempsense startcmd\n"); + stop_cmd(dd); + ret = -ENXIO; + goto bail; + } + ret = wr_byte(dd, regnum); + stop_cmd(dd); + if (ret) { + ipath_dev_err(dd, "Failed tempsense WR command %02X\n", + regnum); + ret = -ENXIO; + goto bail; + } + if (i2c_startcmd(dd, icd->temp_dev | READ_CMD)) { + ipath_dbg("Failed tempsense RD startcmd\n"); + stop_cmd(dd); + ret = -ENXIO; + goto bail; + } + /* + * We can only clock out one byte per command, sensibly + */ + ret = rd_byte(dd); + stop_cmd(dd); + +bail: + return ret; +} + +#define VALID_TS_RD_REG_MASK 0xBF + +/** + * ipath_tempsense_read - read register of temp sensor via I2C + * @dd: the infinipath device + * @regnum: register to read from + * + * returns reg contents (0..255) or < 0 for error + */ +int ipath_tempsense_read(struct ipath_devdata *dd, u8 regnum) +{ + int ret; + + if (regnum > 7) + return -EINVAL; + + /* return a bogus value for (the one) register we do not have */ + if (!((1 << regnum) & VALID_TS_RD_REG_MASK)) + return 0; + + ret = mutex_lock_interruptible(&dd->ipath_eep_lock); + if (!ret) { + ret = ipath_tempsense_internal_read(dd, regnum); + mutex_unlock(&dd->ipath_eep_lock); + } + + /* + * There are three possibilities here: + * ret is actual value (0..255) + * ret is -ENXIO or -EINVAL from code in this file + * ret is -EINTR from mutex_lock_interruptible. + */ + return ret; +} + +static int ipath_tempsense_internal_write(struct ipath_devdata *dd, + u8 regnum, u8 data) +{ + int ret = -ENOENT; + struct i2c_chain_desc *icd; + + icd = ipath_i2c_type(dd); + if (!icd) + goto bail; + + if (icd->temp_dev == IPATH_NO_DEV) { + /* tempsense only exists on new, real-I2C boards */ + ret = -ENXIO; + goto bail; + } + if (i2c_startcmd(dd, icd->temp_dev | WRITE_CMD)) { + ipath_dbg("Failed tempsense startcmd\n"); + stop_cmd(dd); + ret = -ENXIO; + goto bail; + } + ret = wr_byte(dd, regnum); + if (ret) { + stop_cmd(dd); + ipath_dev_err(dd, "Failed to write tempsense command %02X\n", + regnum); + ret = -ENXIO; + goto bail; + } + ret = wr_byte(dd, data); + stop_cmd(dd); + ret = i2c_startcmd(dd, icd->temp_dev | READ_CMD); + if (ret) { + ipath_dev_err(dd, "Failed tempsense data wrt to %02X\n", + regnum); + ret = -ENXIO; + } + +bail: + return ret; +} + +#define VALID_TS_WR_REG_MASK ((1 << 9) | (1 << 0xB) | (1 << 0xD)) + +/** + * ipath_tempsense_write - write register of temp sensor via I2C + * @dd: the infinipath device + * @regnum: register to write + * @data: data to write + * + * returns 0 for success or < 0 for error + */ +int ipath_tempsense_write(struct ipath_devdata *dd, u8 regnum, u8 data) +{ + int ret; + + if (regnum > 15 || !((1 << regnum) & VALID_TS_WR_REG_MASK)) + return -EINVAL; + + ret = mutex_lock_interruptible(&dd->ipath_eep_lock); + if (!ret) { + ret = ipath_tempsense_internal_write(dd, regnum, data); + mutex_unlock(&dd->ipath_eep_lock); + } + + /* + * There are three possibilities here: + * ret is 0 for success + * ret is -ENXIO or -EINVAL from code in this file + * ret is -EINTR from mutex_lock_interruptible. + */ + return ret; +} |