diff options
Diffstat (limited to 'drivers/tty/serial/8250/8250_bcm2835aux.c')
| -rw-r--r-- | drivers/tty/serial/8250/8250_bcm2835aux.c | 143 |
1 files changed, 128 insertions, 15 deletions
diff --git a/drivers/tty/serial/8250/8250_bcm2835aux.c b/drivers/tty/serial/8250/8250_bcm2835aux.c index e70e3cc30050..15a2387a5b25 100644 --- a/drivers/tty/serial/8250/8250_bcm2835aux.c +++ b/drivers/tty/serial/8250/8250_bcm2835aux.c @@ -6,6 +6,10 @@ * * Based on 8250_lpc18xx.c: * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com> + * + * The bcm2835aux is capable of RTS auto flow-control, but this driver doesn't + * take advantage of it yet. When adding support, be sure not to enable it + * simultaneously to rs485. */ #include <linux/clk.h> @@ -13,24 +17,80 @@ #include <linux/module.h> #include <linux/of.h> #include <linux/platform_device.h> +#include <linux/property.h> #include "8250.h" +#define BCM2835_AUX_UART_CNTL 8 +#define BCM2835_AUX_UART_CNTL_RXEN 0x01 /* Receiver enable */ +#define BCM2835_AUX_UART_CNTL_TXEN 0x02 /* Transmitter enable */ +#define BCM2835_AUX_UART_CNTL_AUTORTS 0x04 /* RTS set by RX fill level */ +#define BCM2835_AUX_UART_CNTL_AUTOCTS 0x08 /* CTS stops transmitter */ +#define BCM2835_AUX_UART_CNTL_RTS3 0x00 /* RTS set until 3 chars left */ +#define BCM2835_AUX_UART_CNTL_RTS2 0x10 /* RTS set until 2 chars left */ +#define BCM2835_AUX_UART_CNTL_RTS1 0x20 /* RTS set until 1 chars left */ +#define BCM2835_AUX_UART_CNTL_RTS4 0x30 /* RTS set until 4 chars left */ +#define BCM2835_AUX_UART_CNTL_RTSINV 0x40 /* Invert auto RTS polarity */ +#define BCM2835_AUX_UART_CNTL_CTSINV 0x80 /* Invert auto CTS polarity */ + /** * struct bcm2835aux_data - driver private data of BCM2835 auxiliary UART * @clk: clock producer of the port's uartclk * @line: index of the port's serial8250_ports[] entry + * @cntl: cached copy of CNTL register */ struct bcm2835aux_data { struct clk *clk; int line; + u32 cntl; +}; + +struct bcm2835_aux_serial_driver_data { + resource_size_t offset; }; +static void bcm2835aux_rs485_start_tx(struct uart_8250_port *up) +{ + if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) { + struct bcm2835aux_data *data = dev_get_drvdata(up->port.dev); + + data->cntl &= ~BCM2835_AUX_UART_CNTL_RXEN; + serial_out(up, BCM2835_AUX_UART_CNTL, data->cntl); + } + + /* + * On the bcm2835aux, the MCR register contains no other + * flags besides RTS. So no need for a read-modify-write. + */ + if (up->port.rs485.flags & SER_RS485_RTS_ON_SEND) + serial8250_out_MCR(up, 0); + else + serial8250_out_MCR(up, UART_MCR_RTS); +} + +static void bcm2835aux_rs485_stop_tx(struct uart_8250_port *up) +{ + if (up->port.rs485.flags & SER_RS485_RTS_AFTER_SEND) + serial8250_out_MCR(up, 0); + else + serial8250_out_MCR(up, UART_MCR_RTS); + + if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) { + struct bcm2835aux_data *data = dev_get_drvdata(up->port.dev); + + data->cntl |= BCM2835_AUX_UART_CNTL_RXEN; + serial_out(up, BCM2835_AUX_UART_CNTL, data->cntl); + } +} + static int bcm2835aux_serial_probe(struct platform_device *pdev) { + const struct bcm2835_aux_serial_driver_data *bcm_data; struct uart_8250_port up = { }; struct bcm2835aux_data *data; + resource_size_t offset = 0; struct resource *res; + unsigned int uartclk; int ret; /* allocate the custom structure */ @@ -47,15 +107,18 @@ static int bcm2835aux_serial_probe(struct platform_device *pdev) up.port.fifosize = 8; up.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_SKIP_TEST | UPF_IOREMAP; + up.port.rs485_config = serial8250_em485_config; + up.port.rs485_supported = serial8250_em485_supported; + up.rs485_start_tx = bcm2835aux_rs485_start_tx; + up.rs485_stop_tx = bcm2835aux_rs485_stop_tx; + + /* initialize cached copy with power-on reset value */ + data->cntl = BCM2835_AUX_UART_CNTL_RXEN | BCM2835_AUX_UART_CNTL_TXEN; + + platform_set_drvdata(pdev, data); /* get the clock - this also enables the HW */ - data->clk = devm_clk_get(&pdev->dev, NULL); - ret = PTR_ERR_OR_ZERO(data->clk); - if (ret) { - if (ret != -EPROBE_DEFER) - dev_err(&pdev->dev, "could not get clk: %d\n", ret); - return ret; - } + data->clk = devm_clk_get_optional(&pdev->dev, NULL); /* get the interrupt */ ret = platform_get_irq(pdev, 0); @@ -69,8 +132,24 @@ static int bcm2835aux_serial_probe(struct platform_device *pdev) dev_err(&pdev->dev, "memory resource not found"); return -EINVAL; } - up.port.mapbase = res->start; - up.port.mapsize = resource_size(res); + + bcm_data = device_get_match_data(&pdev->dev); + + /* Some UEFI implementations (e.g. tianocore/edk2 for the Raspberry Pi) + * describe the miniuart with a base address that encompasses the auxiliary + * registers shared between the miniuart and spi. + * + * This is due to historical reasons, see discussion here : + * https://edk2.groups.io/g/devel/topic/87501357#84349 + * + * We need to add the offset between the miniuart and auxiliary + * registers to get the real miniuart base address. + */ + if (bcm_data) + offset = bcm_data->offset; + + up.port.mapbase = res->start + offset; + up.port.mapsize = resource_size(res) - offset; /* Check for a fixed line number */ ret = of_alias_get_id(pdev->dev.of_node, "serial"); @@ -85,25 +164,30 @@ static int bcm2835aux_serial_probe(struct platform_device *pdev) return ret; } + uartclk = clk_get_rate(data->clk); + if (!uartclk) { + ret = device_property_read_u32(&pdev->dev, "clock-frequency", &uartclk); + if (ret) { + dev_err_probe(&pdev->dev, ret, "could not get clk rate\n"); + goto dis_clk; + } + } + /* the HW-clock divider for bcm2835aux is 8, * but 8250 expects a divider of 16, * so we have to multiply the actual clock by 2 * to get identical baudrates. */ - up.port.uartclk = clk_get_rate(data->clk) * 2; + up.port.uartclk = uartclk * 2; /* register the port */ ret = serial8250_register_8250_port(&up); if (ret < 0) { - if (ret != -EPROBE_DEFER) - dev_err(&pdev->dev, - "unable to register 8250 port - %d\n", ret); + dev_err_probe(&pdev->dev, ret, "unable to register 8250 port\n"); goto dis_clk; } data->line = ret; - platform_set_drvdata(pdev, data); - return 0; dis_clk: @@ -121,22 +205,51 @@ static int bcm2835aux_serial_remove(struct platform_device *pdev) return 0; } +static const struct bcm2835_aux_serial_driver_data bcm2835_acpi_data = { + .offset = 0x40, +}; + static const struct of_device_id bcm2835aux_serial_match[] = { { .compatible = "brcm,bcm2835-aux-uart" }, { }, }; MODULE_DEVICE_TABLE(of, bcm2835aux_serial_match); +static const struct acpi_device_id bcm2835aux_serial_acpi_match[] = { + { "BCM2836", (kernel_ulong_t)&bcm2835_acpi_data }, + { } +}; +MODULE_DEVICE_TABLE(acpi, bcm2835aux_serial_acpi_match); + static struct platform_driver bcm2835aux_serial_driver = { .driver = { .name = "bcm2835-aux-uart", .of_match_table = bcm2835aux_serial_match, + .acpi_match_table = bcm2835aux_serial_acpi_match, }, .probe = bcm2835aux_serial_probe, .remove = bcm2835aux_serial_remove, }; module_platform_driver(bcm2835aux_serial_driver); +#ifdef CONFIG_SERIAL_8250_CONSOLE + +static int __init early_bcm2835aux_setup(struct earlycon_device *device, + const char *options) +{ + if (!device->port.membase) + return -ENODEV; + + device->port.iotype = UPIO_MEM32; + device->port.regshift = 2; + + return early_serial8250_setup(device, NULL); +} + +OF_EARLYCON_DECLARE(bcm2835aux, "brcm,bcm2835-aux-uart", + early_bcm2835aux_setup); +#endif + MODULE_DESCRIPTION("BCM2835 auxiliar UART driver"); MODULE_AUTHOR("Martin Sperl <kernel@martin.sperl.org>"); MODULE_LICENSE("GPL v2"); |