diff options
Diffstat (limited to 'drivers/tty/serial/8250/8250_port.c')
| -rw-r--r-- | drivers/tty/serial/8250/8250_port.c | 2912 |
1 files changed, 2912 insertions, 0 deletions
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c new file mode 100644 index 000000000000..54e6c8ddef5d --- /dev/null +++ b/drivers/tty/serial/8250/8250_port.c @@ -0,0 +1,2912 @@ +/* + * Base port operations for 8250/16550-type serial ports + * + * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. + * Split from 8250_core.c, Copyright (C) 2001 Russell King. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * A note about mapbase / membase + * + * mapbase is the physical address of the IO port. + * membase is an 'ioremapped' cookie. + */ + +#if defined(CONFIG_SERIAL_8250_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#define SUPPORT_SYSRQ +#endif + +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/sysrq.h> +#include <linux/delay.h> +#include <linux/platform_device.h> +#include <linux/tty.h> +#include <linux/ratelimit.h> +#include <linux/tty_flip.h> +#include <linux/serial.h> +#include <linux/serial_8250.h> +#include <linux/nmi.h> +#include <linux/mutex.h> +#include <linux/slab.h> +#include <linux/uaccess.h> +#include <linux/pm_runtime.h> + +#include <asm/io.h> +#include <asm/irq.h> + +#include "8250.h" + +/* + * Debugging. + */ +#if 0 +#define DEBUG_AUTOCONF(fmt...) printk(fmt) +#else +#define DEBUG_AUTOCONF(fmt...) do { } while (0) +#endif + +#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) + +/* + * Here we define the default xmit fifo size used for each type of UART. + */ +static const struct serial8250_config uart_config[] = { + [PORT_UNKNOWN] = { + .name = "unknown", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_8250] = { + .name = "8250", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16450] = { + .name = "16450", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550] = { + .name = "16550", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550A] = { + .name = "16550A", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .rxtrig_bytes = {1, 4, 8, 14}, + .flags = UART_CAP_FIFO, + }, + [PORT_CIRRUS] = { + .name = "Cirrus", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16650] = { + .name = "ST16650", + .fifo_size = 1, + .tx_loadsz = 1, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_16650V2] = { + .name = "ST16650V2", + .fifo_size = 32, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | + UART_FCR_T_TRIG_00, + .rxtrig_bytes = {8, 16, 24, 28}, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_16750] = { + .name = "TI16750", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 | + UART_FCR7_64BYTE, + .rxtrig_bytes = {1, 16, 32, 56}, + .flags = UART_CAP_FIFO | UART_CAP_SLEEP | UART_CAP_AFE, + }, + [PORT_STARTECH] = { + .name = "Startech", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16C950] = { + .name = "16C950/954", + .fifo_size = 128, + .tx_loadsz = 128, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + /* UART_CAP_EFR breaks billionon CF bluetooth card. */ + .flags = UART_CAP_FIFO | UART_CAP_SLEEP, + }, + [PORT_16654] = { + .name = "ST16654", + .fifo_size = 64, + .tx_loadsz = 32, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | + UART_FCR_T_TRIG_10, + .rxtrig_bytes = {8, 16, 56, 60}, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_16850] = { + .name = "XR16850", + .fifo_size = 128, + .tx_loadsz = 128, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_RSA] = { + .name = "RSA", + .fifo_size = 2048, + .tx_loadsz = 2048, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11, + .flags = UART_CAP_FIFO, + }, + [PORT_NS16550A] = { + .name = "NS16550A", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_NATSEMI, + }, + [PORT_XSCALE] = { + .name = "XScale", + .fifo_size = 32, + .tx_loadsz = 32, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_UUE | UART_CAP_RTOIE, + }, + [PORT_OCTEON] = { + .name = "OCTEON", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO, + }, + [PORT_AR7] = { + .name = "AR7", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_U6_16550A] = { + .name = "U6_16550A", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_TEGRA] = { + .name = "Tegra", + .fifo_size = 32, + .tx_loadsz = 8, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | + UART_FCR_T_TRIG_01, + .rxtrig_bytes = {1, 4, 8, 14}, + .flags = UART_CAP_FIFO | UART_CAP_RTOIE, + }, + [PORT_XR17D15X] = { + .name = "XR17D15X", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP, + }, + [PORT_XR17V35X] = { + .name = "XR17V35X", + .fifo_size = 256, + .tx_loadsz = 256, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 | + UART_FCR_T_TRIG_11, + .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP, + }, + [PORT_LPC3220] = { + .name = "LPC3220", + .fifo_size = 64, + .tx_loadsz = 32, + .fcr = UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO | + UART_FCR_R_TRIG_00 | UART_FCR_T_TRIG_00, + .flags = UART_CAP_FIFO, + }, + [PORT_BRCM_TRUMANAGE] = { + .name = "TruManage", + .fifo_size = 1, + .tx_loadsz = 1024, + .flags = UART_CAP_HFIFO, + }, + [PORT_8250_CIR] = { + .name = "CIR port" + }, + [PORT_ALTR_16550_F32] = { + .name = "Altera 16550 FIFO32", + .fifo_size = 32, + .tx_loadsz = 32, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_ALTR_16550_F64] = { + .name = "Altera 16550 FIFO64", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_ALTR_16550_F128] = { + .name = "Altera 16550 FIFO128", + .fifo_size = 128, + .tx_loadsz = 128, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, +/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement +workaround of errata A-008006 which states that tx_loadsz should be +configured less than Maximum supported fifo bytes */ + [PORT_16550A_FSL64] = { + .name = "16550A_FSL64", + .fifo_size = 64, + .tx_loadsz = 63, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 | + UART_FCR7_64BYTE, + .flags = UART_CAP_FIFO, + }, +}; + +/* Uart divisor latch read */ +static int default_serial_dl_read(struct uart_8250_port *up) +{ + return serial_in(up, UART_DLL) | serial_in(up, UART_DLM) << 8; +} + +/* Uart divisor latch write */ +static void default_serial_dl_write(struct uart_8250_port *up, int value) +{ + serial_out(up, UART_DLL, value & 0xff); + serial_out(up, UART_DLM, value >> 8 & 0xff); +} + +#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X) + +/* Au1x00/RT288x UART hardware has a weird register layout */ +static const s8 au_io_in_map[8] = { + 0, /* UART_RX */ + 2, /* UART_IER */ + 3, /* UART_IIR */ + 5, /* UART_LCR */ + 6, /* UART_MCR */ + 7, /* UART_LSR */ + 8, /* UART_MSR */ + -1, /* UART_SCR (unmapped) */ +}; + +static const s8 au_io_out_map[8] = { + 1, /* UART_TX */ + 2, /* UART_IER */ + 4, /* UART_FCR */ + 5, /* UART_LCR */ + 6, /* UART_MCR */ + -1, /* UART_LSR (unmapped) */ + -1, /* UART_MSR (unmapped) */ + -1, /* UART_SCR (unmapped) */ +}; + +static unsigned int au_serial_in(struct uart_port *p, int offset) +{ + if (offset >= ARRAY_SIZE(au_io_in_map)) + return UINT_MAX; + offset = au_io_in_map[offset]; + if (offset < 0) + return UINT_MAX; + return __raw_readl(p->membase + (offset << p->regshift)); +} + +static void au_serial_out(struct uart_port *p, int offset, int value) +{ + if (offset >= ARRAY_SIZE(au_io_out_map)) + return; + offset = au_io_out_map[offset]; + if (offset < 0) + return; + __raw_writel(value, p->membase + (offset << p->regshift)); +} + +/* Au1x00 haven't got a standard divisor latch */ +static int au_serial_dl_read(struct uart_8250_port *up) +{ + return __raw_readl(up->port.membase + 0x28); +} + +static void au_serial_dl_write(struct uart_8250_port *up, int value) +{ + __raw_writel(value, up->port.membase + 0x28); +} + +#endif + +static unsigned int hub6_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + outb(p->hub6 - 1 + offset, p->iobase); + return inb(p->iobase + 1); +} + +static void hub6_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + outb(p->hub6 - 1 + offset, p->iobase); + outb(value, p->iobase + 1); +} + +static unsigned int mem_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return readb(p->membase + offset); +} + +static void mem_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + writeb(value, p->membase + offset); +} + +static void mem32_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + writel(value, p->membase + offset); +} + +static unsigned int mem32_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return readl(p->membase + offset); +} + +static void mem32be_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + iowrite32be(value, p->membase + offset); +} + +static unsigned int mem32be_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return ioread32be(p->membase + offset); +} + +static unsigned int io_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return inb(p->iobase + offset); +} + +static void io_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + outb(value, p->iobase + offset); +} + +static int serial8250_default_handle_irq(struct uart_port *port); +static int exar_handle_irq(struct uart_port *port); + +static void set_io_from_upio(struct uart_port *p) +{ + struct uart_8250_port *up = up_to_u8250p(p); + + up->dl_read = default_serial_dl_read; + up->dl_write = default_serial_dl_write; + + switch (p->iotype) { + case UPIO_HUB6: + p->serial_in = hub6_serial_in; + p->serial_out = hub6_serial_out; + break; + + case UPIO_MEM: + p->serial_in = mem_serial_in; + p->serial_out = mem_serial_out; + break; + + case UPIO_MEM32: + p->serial_in = mem32_serial_in; + p->serial_out = mem32_serial_out; + break; + + case UPIO_MEM32BE: + p->serial_in = mem32be_serial_in; + p->serial_out = mem32be_serial_out; + break; + +#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X) + case UPIO_AU: + p->serial_in = au_serial_in; + p->serial_out = au_serial_out; + up->dl_read = au_serial_dl_read; + up->dl_write = au_serial_dl_write; + break; +#endif + + default: + p->serial_in = io_serial_in; + p->serial_out = io_serial_out; + break; + } + /* Remember loaded iotype */ + up->cur_iotype = p->iotype; + p->handle_irq = serial8250_default_handle_irq; +} + +static void +serial_port_out_sync(struct uart_port *p, int offset, int value) +{ + switch (p->iotype) { + case UPIO_MEM: + case UPIO_MEM32: + case UPIO_MEM32BE: + case UPIO_AU: + p->serial_out(p, offset, value); + p->serial_in(p, UART_LCR); /* safe, no side-effects */ + break; + default: + p->serial_out(p, offset, value); + } +} + +/* + * For the 16C950 + */ +static void serial_icr_write(struct uart_8250_port *up, int offset, int value) +{ + serial_out(up, UART_SCR, offset); + serial_out(up, UART_ICR, value); +} + +static unsigned int serial_icr_read(struct uart_8250_port *up, int offset) +{ + unsigned int value; + + serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD); + serial_out(up, UART_SCR, offset); + value = serial_in(up, UART_ICR); + serial_icr_write(up, UART_ACR, up->acr); + + return value; +} + +/* + * FIFO support. + */ +static void serial8250_clear_fifos(struct uart_8250_port *p) +{ + if (p->capabilities & UART_CAP_FIFO) { + serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_out(p, UART_FCR, 0); + } +} + +void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p) +{ + serial8250_clear_fifos(p); + serial_out(p, UART_FCR, p->fcr); +} +EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos); + +void serial8250_rpm_get(struct uart_8250_port *p) +{ + if (!(p->capabilities & UART_CAP_RPM)) + return; + pm_runtime_get_sync(p->port.dev); +} +EXPORT_SYMBOL_GPL(serial8250_rpm_get); + +void serial8250_rpm_put(struct uart_8250_port *p) +{ + if (!(p->capabilities & UART_CAP_RPM)) + return; + pm_runtime_mark_last_busy(p->port.dev); + pm_runtime_put_autosuspend(p->port.dev); +} +EXPORT_SYMBOL_GPL(serial8250_rpm_put); + +/* + * These two wrappers ensure that enable_runtime_pm_tx() can be called more than + * once and disable_runtime_pm_tx() will still disable RPM because the fifo is + * empty and the HW can idle again. + */ +static void serial8250_rpm_get_tx(struct uart_8250_port *p) +{ + unsigned char rpm_active; + + if (!(p->capabilities & UART_CAP_RPM)) + return; + + rpm_active = xchg(&p->rpm_tx_active, 1); + if (rpm_active) + return; + pm_runtime_get_sync(p->port.dev); +} + +static void serial8250_rpm_put_tx(struct uart_8250_port *p) +{ + unsigned char rpm_active; + + if (!(p->capabilities & UART_CAP_RPM)) + return; + + rpm_active = xchg(&p->rpm_tx_active, 0); + if (!rpm_active) + return; + pm_runtime_mark_last_busy(p->port.dev); + pm_runtime_put_autosuspend(p->port.dev); +} + +/* + * IER sleep support. UARTs which have EFRs need the "extended + * capability" bit enabled. Note that on XR16C850s, we need to + * reset LCR to write to IER. + */ +static void serial8250_set_sleep(struct uart_8250_port *p, int sleep) +{ + unsigned char lcr = 0, efr = 0; + /* + * Exar UARTs have a SLEEP register that enables or disables + * each UART to enter sleep mode separately. On the XR17V35x the + * register is accessible to each UART at the UART_EXAR_SLEEP + * offset but the UART channel may only write to the corresponding + * bit. + */ + serial8250_rpm_get(p); + if ((p->port.type == PORT_XR17V35X) || + (p->port.type == PORT_XR17D15X)) { + serial_out(p, UART_EXAR_SLEEP, sleep ? 0xff : 0); + goto out; + } + + if (p->capabilities & UART_CAP_SLEEP) { + if (p->capabilities & UART_CAP_EFR) { + lcr = serial_in(p, UART_LCR); + efr = serial_in(p, UART_EFR); + serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(p, UART_EFR, UART_EFR_ECB); + serial_out(p, UART_LCR, 0); + } + serial_out(p, UART_IER, sleep ? UART_IERX_SLEEP : 0); + if (p->capabilities & UART_CAP_EFR) { + serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(p, UART_EFR, efr); + serial_out(p, UART_LCR, lcr); + } + } +out: + serial8250_rpm_put(p); +} + +#ifdef CONFIG_SERIAL_8250_RSA +/* + * Attempts to turn on the RSA FIFO. Returns zero on failure. + * We set the port uart clock rate if we succeed. + */ +static int __enable_rsa(struct uart_8250_port *up) +{ + unsigned char mode; + int result; + + mode = serial_in(up, UART_RSA_MSR); + result = mode & UART_RSA_MSR_FIFO; + + if (!result) { + serial_out(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO); + mode = serial_in(up, UART_RSA_MSR); + result = mode & UART_RSA_MSR_FIFO; + } + + if (result) + up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16; + + return result; +} + +static void enable_rsa(struct uart_8250_port *up) +{ + if (up->port.type == PORT_RSA) { + if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) { + spin_lock_irq(&up->port.lock); + __enable_rsa(up); + spin_unlock_irq(&up->port.lock); + } + if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) + serial_out(up, UART_RSA_FRR, 0); + } +} + +/* + * Attempts to turn off the RSA FIFO. Returns zero on failure. + * It is unknown why interrupts were disabled in here. However, + * the caller is expected to preserve this behaviour by grabbing + * the spinlock before calling this function. + */ +static void disable_rsa(struct uart_8250_port *up) +{ + unsigned char mode; + int result; + + if (up->port.type == PORT_RSA && + up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) { + spin_lock_irq(&up->port.lock); + + mode = serial_in(up, UART_RSA_MSR); + result = !(mode & UART_RSA_MSR_FIFO); + + if (!result) { + serial_out(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO); + mode = serial_in(up, UART_RSA_MSR); + result = !(mode & UART_RSA_MSR_FIFO); + } + + if (result) + up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16; + spin_unlock_irq(&up->port.lock); + } +} +#endif /* CONFIG_SERIAL_8250_RSA */ + +/* + * This is a quickie test to see how big the FIFO is. + * It doesn't work at all the time, more's the pity. + */ +static int size_fifo(struct uart_8250_port *up) +{ + unsigned char old_fcr, old_mcr, old_lcr; + unsigned short old_dl; + int count; + + old_lcr = serial_in(up, UART_LCR); + serial_out(up, UART_LCR, 0); + old_fcr = serial_in(up, UART_FCR); + old_mcr = serial_in(up, UART_MCR); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_out(up, UART_MCR, UART_MCR_LOOP); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + old_dl = serial_dl_read(up); + serial_dl_write(up, 0x0001); + serial_out(up, UART_LCR, 0x03); + for (count = 0; count < 256; count++) + serial_out(up, UART_TX, count); + mdelay(20);/* FIXME - schedule_timeout */ + for (count = 0; (serial_in(up, UART_LSR) & UART_LSR_DR) && + (count < 256); count++) + serial_in(up, UART_RX); + serial_out(up, UART_FCR, old_fcr); + serial_out(up, UART_MCR, old_mcr); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + serial_dl_write(up, old_dl); + serial_out(up, UART_LCR, old_lcr); + + return count; +} + +/* + * Read UART ID using the divisor method - set DLL and DLM to zero + * and the revision will be in DLL and device type in DLM. We + * preserve the device state across this. + */ +static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p) +{ + unsigned char old_dll, old_dlm, old_lcr; + unsigned int id; + + old_lcr = serial_in(p, UART_LCR); + serial_out(p, UART_LCR, UART_LCR_CONF_MODE_A); + + old_dll = serial_in(p, UART_DLL); + old_dlm = serial_in(p, UART_DLM); + + serial_out(p, UART_DLL, 0); + serial_out(p, UART_DLM, 0); + + id = serial_in(p, UART_DLL) | serial_in(p, UART_DLM) << 8; + + serial_out(p, UART_DLL, old_dll); + serial_out(p, UART_DLM, old_dlm); + serial_out(p, UART_LCR, old_lcr); + + return id; +} + +/* + * This is a helper routine to autodetect StarTech/Exar/Oxsemi UART's. + * When this function is called we know it is at least a StarTech + * 16650 V2, but it might be one of several StarTech UARTs, or one of + * its clones. (We treat the broken original StarTech 16650 V1 as a + * 16550, and why not? Startech doesn't seem to even acknowledge its + * existence.) + * + * What evil have men's minds wrought... + */ +static void autoconfig_has_efr(struct uart_8250_port *up) +{ + unsigned int id1, id2, id3, rev; + + /* + * Everything with an EFR has SLEEP + */ + up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP; + + /* + * First we check to see if it's an Oxford Semiconductor UART. + * + * If we have to do this here because some non-National + * Semiconductor clone chips lock up if you try writing to the + * LSR register (which serial_icr_read does) + */ + + /* + * Check for Oxford Semiconductor 16C950. + * + * EFR [4] must be set else this test fails. + * + * This shouldn't be necessary, but Mike Hudson (Exoray@isys.ca) + * claims that it's needed for 952 dual UART's (which are not + * recommended for new designs). + */ + up->acr = 0; + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(up, UART_EFR, UART_EFR_ECB); + serial_out(up, UART_LCR, 0x00); + id1 = serial_icr_read(up, UART_ID1); + id2 = serial_icr_read(up, UART_ID2); + id3 = serial_icr_read(up, UART_ID3); + rev = serial_icr_read(up, UART_REV); + + DEBUG_AUTOCONF("950id=%02x:%02x:%02x:%02x ", id1, id2, id3, rev); + + if (id1 == 0x16 && id2 == 0xC9 && + (id3 == 0x50 || id3 == 0x52 || id3 == 0x54)) { + up->port.type = PORT_16C950; + + /* + * Enable work around for the Oxford Semiconductor 952 rev B + * chip which causes it to seriously miscalculate baud rates + * when DLL is 0. + */ + if (id3 == 0x52 && rev == 0x01) + up->bugs |= UART_BUG_QUOT; + return; + } + + /* + * We check for a XR16C850 by setting DLL and DLM to 0, and then + * reading back DLL and DLM. The chip type depends on the DLM + * value read back: + * 0x10 - XR16C850 and the DLL contains the chip revision. + * 0x12 - XR16C2850. + * 0x14 - XR16C854. + */ + id1 = autoconfig_read_divisor_id(up); + DEBUG_AUTOCONF("850id=%04x ", id1); + + id2 = id1 >> 8; + if (id2 == 0x10 || id2 == 0x12 || id2 == 0x14) { + up->port.type = PORT_16850; + return; + } + + /* + * It wasn't an XR16C850. + * + * We distinguish between the '654 and the '650 by counting + * how many bytes are in the FIFO. I'm using this for now, + * since that's the technique that was sent to me in the + * serial driver update, but I'm not convinced this works. + * I've had problems doing this in the past. -TYT + */ + if (size_fifo(up) == 64) + up->port.type = PORT_16654; + else + up->port.type = PORT_16650V2; +} + +/* + * We detected a chip without a FIFO. Only two fall into + * this category - the original 8250 and the 16450. The + * 16450 has a scratch register (accessible with LCR=0) + */ +static void autoconfig_8250(struct uart_8250_port *up) +{ + unsigned char scratch, status1, status2; + + up->port.type = PORT_8250; + + scratch = serial_in(up, UART_SCR); + serial_out(up, UART_SCR, 0xa5); + status1 = serial_in(up, UART_SCR); + serial_out(up, UART_SCR, 0x5a); + status2 = serial_in(up, UART_SCR); + serial_out(up, UART_SCR, scratch); + + if (status1 == 0xa5 && status2 == 0x5a) + up->port.type = PORT_16450; +} + +static int broken_efr(struct uart_8250_port *up) +{ + /* + * Exar ST16C2550 "A2" devices incorrectly detect as + * having an EFR, and report an ID of 0x0201. See + * http://linux.derkeiler.com/Mailing-Lists/Kernel/2004-11/4812.html + */ + if (autoconfig_read_divisor_id(up) == 0x0201 && size_fifo(up) == 16) + return 1; + + return 0; +} + +/* + * We know that the chip has FIFOs. Does it have an EFR? The + * EFR is located in the same register position as the IIR and + * we know the top two bits of the IIR are currently set. The + * EFR should contain zero. Try to read the EFR. + */ +static void autoconfig_16550a(struct uart_8250_port *up) +{ + unsigned char status1, status2; + unsigned int iersave; + + up->port.type = PORT_16550A; + up->capabilities |= UART_CAP_FIFO; + + /* + * XR17V35x UARTs have an extra divisor register, DLD + * that gets enabled with when DLAB is set which will + * cause the device to incorrectly match and assign + * port type to PORT_16650. The EFR for this UART is + * found at offset 0x09. Instead check the Deice ID (DVID) + * register for a 2, 4 or 8 port UART. + */ + if (up->port.flags & UPF_EXAR_EFR) { + status1 = serial_in(up, UART_EXAR_DVID); + if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) { + DEBUG_AUTOCONF("Exar XR17V35x "); + up->port.type = PORT_XR17V35X; + up->capabilities |= UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP; + + return; + } + + } + + /* + * Check for presence of the EFR when DLAB is set. + * Only ST16C650V1 UARTs pass this test. + */ + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + if (serial_in(up, UART_EFR) == 0) { + serial_out(up, UART_EFR, 0xA8); + if (serial_in(up, UART_EFR) != 0) { + DEBUG_AUTOCONF("EFRv1 "); + up->port.type = PORT_16650; + up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP; + } else { + serial_out(up, UART_LCR, 0); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR7_64BYTE); + status1 = serial_in(up, UART_IIR) >> 5; + serial_out(up, UART_FCR, 0); + serial_out(up, UART_LCR, 0); + + if (status1 == 7) + up->port.type = PORT_16550A_FSL64; + else + DEBUG_AUTOCONF("Motorola 8xxx DUART "); + } + serial_out(up, UART_EFR, 0); + return; + } + + /* + * Maybe it requires 0xbf to be written to the LCR. + * (other ST16C650V2 UARTs, TI16C752A, etc) + */ + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) { + DEBUG_AUTOCONF("EFRv2 "); + autoconfig_has_efr(up); + return; + } + + /* + * Check for a National Semiconductor SuperIO chip. + * Attempt to switch to bank 2, read the value of the LOOP bit + * from EXCR1. Switch back to bank 0, change it in MCR. Then + * switch back to bank 2, read it from EXCR1 again and check + * it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2 + */ + serial_out(up, UART_LCR, 0); + status1 = serial_in(up, UART_MCR); + serial_out(up, UART_LCR, 0xE0); + status2 = serial_in(up, 0x02); /* EXCR1 */ + + if (!((status2 ^ status1) & UART_MCR_LOOP)) { + serial_out(up, UART_LCR, 0); + serial_out(up, UART_MCR, status1 ^ UART_MCR_LOOP); + serial_out(up, UART_LCR, 0xE0); + status2 = serial_in(up, 0x02); /* EXCR1 */ + serial_out(up, UART_LCR, 0); + serial_out(up, UART_MCR, status1); + + if ((status2 ^ status1) & UART_MCR_LOOP) { + unsigned short quot; + + serial_out(up, UART_LCR, 0xE0); + + quot = serial_dl_read(up); + quot <<= 3; + + if (ns16550a_goto_highspeed(up)) + serial_dl_write(up, quot); + + serial_out(up, UART_LCR, 0); + + up->port.uartclk = 921600*16; + up->port.type = PORT_NS16550A; + up->capabilities |= UART_NATSEMI; + return; + } + } + + /* + * No EFR. Try to detect a TI16750, which only sets bit 5 of + * the IIR when 64 byte FIFO mode is enabled when DLAB is set. + * Try setting it with and without DLAB set. Cheap clones + * set bit 5 without DLAB set. + */ + serial_out(up, UART_LCR, 0); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); + status1 = serial_in(up, UART_IIR) >> 5; + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); + status2 = serial_in(up, UART_IIR) >> 5; + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_out(up, UART_LCR, 0); + + DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2); + + if (status1 == 6 && status2 == 7) { + up->port.type = PORT_16750; + up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP; + return; + } + + /* + * Try writing and reading the UART_IER_UUE bit (b6). + * If it works, this is probably one of the Xscale platform's + * internal UARTs. + * We're going to explicitly set the UUE bit to 0 before + * trying to write and read a 1 just to make sure it's not + * already a 1 and maybe locked there before we even start start. + */ + iersave = serial_in(up, UART_IER); + serial_out(up, UART_IER, iersave & ~UART_IER_UUE); + if (!(serial_in(up, UART_IER) & UART_IER_UUE)) { + /* + * OK it's in a known zero state, try writing and reading + * without disturbing the current state of the other bits. + */ + serial_out(up, UART_IER, iersave | UART_IER_UUE); + if (serial_in(up, UART_IER) & UART_IER_UUE) { + /* + * It's an Xscale. + * We'll leave the UART_IER_UUE bit set to 1 (enabled). + */ + DEBUG_AUTOCONF("Xscale "); + up->port.type = PORT_XSCALE; + up->capabilities |= UART_CAP_UUE | UART_CAP_RTOIE; + return; + } + } else { + /* + * If we got here we couldn't force the IER_UUE bit to 0. + * Log it and continue. + */ + DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 "); + } + serial_out(up, UART_IER, iersave); + + /* + * Exar uarts have EFR in a weird location + */ + if (up->port.flags & UPF_EXAR_EFR) { + DEBUG_AUTOCONF("Exar XR17D15x "); + up->port.type = PORT_XR17D15X; + up->capabilities |= UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP; + + return; + } + + /* + * We distinguish between 16550A and U6 16550A by counting + * how many bytes are in the FIFO. + */ + if (up->port.type == PORT_16550A && size_fifo(up) == 64) { + up->port.type = PORT_U6_16550A; + up->capabilities |= UART_CAP_AFE; + } +} + +/* + * This routine is called by rs_init() to initialize a specific serial + * port. It determines what type of UART chip this serial port is + * using: 8250, 16450, 16550, 16550A. The important question is + * whether or not this UART is a 16550A or not, since this will + * determine whether or not we can use its FIFO features or not. + */ +static void autoconfig(struct uart_8250_port *up) +{ + unsigned char status1, scratch, scratch2, scratch3; + unsigned char save_lcr, save_mcr; + struct uart_port *port = &up->port; + unsigned long flags; + unsigned int old_capabilities; + + if (!port->iobase && !port->mapbase && !port->membase) + return; + + DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04lx, 0x%p): ", + serial_index(port), port->iobase, port->membase); + + /* + * We really do need global IRQs disabled here - we're going to + * be frobbing the chips IRQ enable register to see if it exists. + */ + spin_lock_irqsave(&port->lock, flags); + + up->capabilities = 0; + up->bugs = 0; + + if (!(port->flags & UPF_BUGGY_UART)) { + /* + * Do a simple existence test first; if we fail this, + * there's no point trying anything else. + * + * 0x80 is used as a nonsense port to prevent against + * false positives due to ISA bus float. The + * assumption is that 0x80 is a non-existent port; + * which should be safe since include/asm/io.h also + * makes this assumption. + * + * Note: this is safe as long as MCR bit 4 is clear + * and the device is in "PC" mode. + */ + scratch = serial_in(up, UART_IER); + serial_out(up, UART_IER, 0); +#ifdef __i386__ + outb(0xff, 0x080); +#endif + /* + * Mask out IER[7:4] bits for test as some UARTs (e.g. TL + * 16C754B) allow only to modify them if an EFR bit is set. + */ + scratch2 = serial_in(up, UART_IER) & 0x0f; + serial_out(up, UART_IER, 0x0F); +#ifdef __i386__ + outb(0, 0x080); +#endif + scratch3 = serial_in(up, UART_IER) & 0x0f; + serial_out(up, UART_IER, scratch); + if (scratch2 != 0 || scratch3 != 0x0F) { + /* + * We failed; there's nothing here + */ + spin_unlock_irqrestore(&port->lock, flags); + DEBUG_AUTOCONF("IER test failed (%02x, %02x) ", + scratch2, scratch3); + goto out; + } + } + + save_mcr = serial_in(up, UART_MCR); + save_lcr = serial_in(up, UART_LCR); + + /* + * Check to see if a UART is really there. Certain broken + * internal modems based on the Rockwell chipset fail this + * test, because they apparently don't implement the loopback + * test mode. So this test is skipped on the COM 1 through + * COM 4 ports. This *should* be safe, since no board + * manufacturer would be stupid enough to design a board + * that conflicts with COM 1-4 --- we hope! + */ + if (!(port->flags & UPF_SKIP_TEST)) { + serial_out(up, UART_MCR, UART_MCR_LOOP | 0x0A); + status1 = serial_in(up, UART_MSR) & 0xF0; + serial_out(up, UART_MCR, save_mcr); + if (status1 != 0x90) { + spin_unlock_irqrestore(&port->lock, flags); + DEBUG_AUTOCONF("LOOP test failed (%02x) ", + status1); + goto out; + } + } + + /* + * We're pretty sure there's a port here. Lets find out what + * type of port it is. The IIR top two bits allows us to find + * out if it's 8250 or 16450, 16550, 16550A or later. This + * determines what we test for next. + * + * We also initialise the EFR (if any) to zero for later. The + * EFR occupies the same register location as the FCR and IIR. + */ + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(up, UART_EFR, 0); + serial_out(up, UART_LCR, 0); + + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); + scratch = serial_in(up, UART_IIR) >> 6; + + switch (scratch) { + case 0: + autoconfig_8250(up); + break; + case 1: + port->type = PORT_UNKNOWN; + break; + case 2: + port->type = PORT_16550; + break; + case 3: + autoconfig_16550a(up); + break; + } + +#ifdef CONFIG_SERIAL_8250_RSA + /* + * Only probe for RSA ports if we got the region. + */ + if (port->type == PORT_16550A && up->probe & UART_PROBE_RSA && + __enable_rsa(up)) + port->type = PORT_RSA; +#endif + + serial_out(up, UART_LCR, save_lcr); + + port->fifosize = uart_config[up->port.type].fifo_size; + old_capabilities = up->capabilities; + up->capabilities = uart_config[port->type].flags; + up->tx_loadsz = uart_config[port->type].tx_loadsz; + + if (port->type == PORT_UNKNOWN) + goto out_lock; + + /* + * Reset the UART. + */ +#ifdef CONFIG_SERIAL_8250_RSA + if (port->type == PORT_RSA) + serial_out(up, UART_RSA_FRR, 0); +#endif + serial_out(up, UART_MCR, save_mcr); + serial8250_clear_fifos(up); + serial_in(up, UART_RX); + if (up->capabilities & UART_CAP_UUE) + serial_out(up, UART_IER, UART_IER_UUE); + else + serial_out(up, UART_IER, 0); + +out_lock: + spin_unlock_irqrestore(&port->lock, flags); + if (up->capabilities != old_capabilities) { + printk(KERN_WARNING + "ttyS%d: detected caps %08x should be %08x\n", + serial_index(port), old_capabilities, + up->capabilities); + } +out: + DEBUG_AUTOCONF("iir=%d ", scratch); + DEBUG_AUTOCONF("type=%s\n", uart_config[port->type].name); +} + +static void autoconfig_irq(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + unsigned char save_mcr, save_ier; + unsigned char save_ICP = 0; + unsigned int ICP = 0; + unsigned long irqs; + int irq; + + if (port->flags & UPF_FOURPORT) { + ICP = (port->iobase & 0xfe0) | 0x1f; + save_ICP = inb_p(ICP); + outb_p(0x80, ICP); + inb_p(ICP); + } + + /* forget possible initially masked and pending IRQ */ + probe_irq_off(probe_irq_on()); + save_mcr = serial_in(up, UART_MCR); + save_ier = serial_in(up, UART_IER); + serial_out(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2); + + irqs = probe_irq_on(); + serial_out(up, UART_MCR, 0); + udelay(10); + if (port->flags & UPF_FOURPORT) { + serial_out(up, UART_MCR, + UART_MCR_DTR | UART_MCR_RTS); + } else { + serial_out(up, UART_MCR, + UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2); + } + serial_out(up, UART_IER, 0x0f); /* enable all intrs */ + serial_in(up, UART_LSR); + serial_in(up, UART_RX); + serial_in(up, UART_IIR); + serial_in(up, UART_MSR); + serial_out(up, UART_TX, 0xFF); + udelay(20); + irq = probe_irq_off(irqs); + + serial_out(up, UART_MCR, save_mcr); + serial_out(up, UART_IER, save_ier); + + if (port->flags & UPF_FOURPORT) + outb_p(save_ICP, ICP); + + port->irq = (irq > 0) ? irq : 0; +} + +static inline void __stop_tx(struct uart_8250_port *p) +{ + if (p->ier & UART_IER_THRI) { + p->ier &= ~UART_IER_THRI; + serial_out(p, UART_IER, p->ier); + serial8250_rpm_put_tx(p); + } +} + +static void serial8250_stop_tx(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get(up); + __stop_tx(up); + + /* + * We really want to stop the transmitter from sending. + */ + if (port->type == PORT_16C950) { + up->acr |= UART_ACR_TXDIS; + serial_icr_write(up, UART_ACR, up->acr); + } + serial8250_rpm_put(up); +} + +static void serial8250_start_tx(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get_tx(up); + + if (up->dma && !up->dma->tx_dma(up)) + return; + + if (!(up->ier & UART_IER_THRI)) { + up->ier |= UART_IER_THRI; + serial_port_out(port, UART_IER, up->ier); + + if (up->bugs & UART_BUG_TXEN) { + unsigned char lsr; + lsr = serial_in(up, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + if (lsr & UART_LSR_THRE) + serial8250_tx_chars(up); + } + } + + /* + * Re-enable the transmitter if we disabled it. + */ + if (port->type == PORT_16C950 && up->acr & UART_ACR_TXDIS) { + up->acr &= ~UART_ACR_TXDIS; + serial_icr_write(up, UART_ACR, up->acr); + } +} + +static void serial8250_throttle(struct uart_port *port) +{ + port->throttle(port); +} + +static void serial8250_unthrottle(struct uart_port *port) +{ + port->unthrottle(port); +} + +static void serial8250_stop_rx(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get(up); + + up->ier &= ~(UART_IER_RLSI | UART_IER_RDI); + up->port.read_status_mask &= ~UART_LSR_DR; + serial_port_out(port, UART_IER, up->ier); + + serial8250_rpm_put(up); +} + +static void serial8250_disable_ms(struct uart_port *port) +{ + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); + + /* no MSR capabilities */ + if (up->bugs & UART_BUG_NOMSR) + return; + + up->ier &= ~UART_IER_MSI; + serial_port_out(port, UART_IER, up->ier); +} + +static void serial8250_enable_ms(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + /* no MSR capabilities */ + if (up->bugs & UART_BUG_NOMSR) + return; + + up->ier |= UART_IER_MSI; + + serial8250_rpm_get(up); + serial_port_out(port, UART_IER, up->ier); + serial8250_rpm_put(up); +} + +/* + * serial8250_rx_chars: processes according to the passed in LSR + * value, and returns the remaining LSR bits not handled + * by this Rx routine. + */ +unsigned char +serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr) +{ + struct uart_port *port = &up->port; + unsigned char ch; + int max_count = 256; + char flag; + + do { + if (likely(lsr & UART_LSR_DR)) + ch = serial_in(up, UART_RX); + else + /* + * Intel 82571 has a Serial Over Lan device that will + * set UART_LSR_BI without setting UART_LSR_DR when + * it receives a break. To avoid reading from the + * receive buffer without UART_LSR_DR bit set, we + * just force the read character to be 0 + */ + ch = 0; + + flag = TTY_NORMAL; + port->icount.rx++; + + lsr |= up->lsr_saved_flags; + up->lsr_saved_flags = 0; + + if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) { + if (lsr & UART_LSR_BI) { + lsr &= ~(UART_LSR_FE | UART_LSR_PE); + port->icount.brk++; + /* + * We do the SysRQ and SAK checking + * here because otherwise the break + * may get masked by ignore_status_mask + * or read_status_mask. + */ + if (uart_handle_break(port)) + goto ignore_char; + } else if (lsr & UART_LSR_PE) + port->icount.parity++; + else if (lsr & UART_LSR_FE) + port->icount.frame++; + if (lsr & UART_LSR_OE) + port->icount.overrun++; + + /* + * Mask off conditions which should be ignored. + */ + lsr &= port->read_status_mask; + + if (lsr & UART_LSR_BI) { + DEBUG_INTR("handling break...."); + flag = TTY_BREAK; + } else if (lsr & UART_LSR_PE) + flag = TTY_PARITY; + else if (lsr & UART_LSR_FE) + flag = TTY_FRAME; + } + if (uart_handle_sysrq_char(port, ch)) + goto ignore_char; + + uart_insert_char(port, lsr, UART_LSR_OE, ch, flag); + +ignore_char: + lsr = serial_in(up, UART_LSR); + } while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (--max_count > 0)); + spin_unlock(&port->lock); + tty_flip_buffer_push(&port->state->port); + spin_lock(&port->lock); + return lsr; +} +EXPORT_SYMBOL_GPL(serial8250_rx_chars); + +void serial8250_tx_chars(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + struct circ_buf *xmit = &port->state->xmit; + int count; + + if (port->x_char) { + serial_out(up, UART_TX, port->x_char); + port->icount.tx++; + port->x_char = 0; + return; + } + if (uart_tx_stopped(port)) { + serial8250_stop_tx(port); + return; + } + if (uart_circ_empty(xmit)) { + __stop_tx(up); + return; + } + + count = up->tx_loadsz; + do { + serial_out(up, UART_TX, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + if (uart_circ_empty(xmit)) + break; + if (up->capabilities & UART_CAP_HFIFO) { + if ((serial_port_in(port, UART_LSR) & BOTH_EMPTY) != + BOTH_EMPTY) + break; + } + } while (--count > 0); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + + DEBUG_INTR("THRE..."); + + /* + * With RPM enabled, we have to wait until the FIFO is empty before the + * HW can go idle. So we get here once again with empty FIFO and disable + * the interrupt and RPM in __stop_tx() + */ + if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM)) + __stop_tx(up); +} +EXPORT_SYMBOL_GPL(serial8250_tx_chars); + +/* Caller holds uart port lock */ +unsigned int serial8250_modem_status(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + unsigned int status = serial_in(up, UART_MSR); + + status |= up->msr_saved_flags; + up->msr_saved_flags = 0; + if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI && + port->state != NULL) { + if (status & UART_MSR_TERI) + port->icount.rng++; + if (status & UART_MSR_DDSR) + port->icount.dsr++; + if (status & UART_MSR_DDCD) + uart_handle_dcd_change(port, status & UART_MSR_DCD); + if (status & UART_MSR_DCTS) + uart_handle_cts_change(port, status & UART_MSR_CTS); + + wake_up_interruptible(&port->state->port.delta_msr_wait); + } + + return status; +} +EXPORT_SYMBOL_GPL(serial8250_modem_status); + +/* + * This handles the interrupt from one port. + */ +int serial8250_handle_irq(struct uart_port *port, unsigned int iir) +{ + unsigned char status; + unsigned long flags; + struct uart_8250_port *up = up_to_u8250p(port); + int dma_err = 0; + + if (iir & UART_IIR_NO_INT) + return 0; + + spin_lock_irqsave(&port->lock, flags); + + status = serial_port_in(port, UART_LSR); + + DEBUG_INTR("status = %x...", status); + + if (status & (UART_LSR_DR | UART_LSR_BI)) { + if (up->dma) + dma_err = up->dma->rx_dma(up, iir); + + if (!up->dma || dma_err) + status = serial8250_rx_chars(up, status); + } + serial8250_modem_status(up); + if ((!up->dma || (up->dma && up->dma->tx_err)) && + (status & UART_LSR_THRE)) + serial8250_tx_chars(up); + + spin_unlock_irqrestore(&port->lock, flags); + return 1; +} +EXPORT_SYMBOL_GPL(serial8250_handle_irq); + +static int serial8250_default_handle_irq(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned int iir; + int ret; + + serial8250_rpm_get(up); + + iir = serial_port_in(port, UART_IIR); + ret = serial8250_handle_irq(port, iir); + + serial8250_rpm_put(up); + return ret; +} + +/* + * These Exar UARTs have an extra interrupt indicator that could + * fire for a few unimplemented interrupts. One of which is a + * wakeup event when coming out of sleep. Put this here just + * to be on the safe side that these interrupts don't go unhandled. + */ +static int exar_handle_irq(struct uart_port *port) +{ + unsigned char int0, int1, int2, int3; + unsigned int iir = serial_port_in(port, UART_IIR); + int ret; + + ret = serial8250_handle_irq(port, iir); + + if ((port->type == PORT_XR17V35X) || + (port->type == PORT_XR17D15X)) { + int0 = serial_port_in(port, 0x80); + int1 = serial_port_in(port, 0x81); + int2 = serial_port_in(port, 0x82); + int3 = serial_port_in(port, 0x83); + } + + return ret; +} + +static unsigned int serial8250_tx_empty(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + unsigned int lsr; + + serial8250_rpm_get(up); + + spin_lock_irqsave(&port->lock, flags); + lsr = serial_port_in(port, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + spin_unlock_irqrestore(&port->lock, flags); + + serial8250_rpm_put(up); + + return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0; +} + +static unsigned int serial8250_get_mctrl(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned int status; + unsigned int ret; + + serial8250_rpm_get(up); + status = serial8250_modem_status(up); + serial8250_rpm_put(up); + + ret = 0; + if (status & UART_MSR_DCD) + ret |= TIOCM_CAR; + if (status & UART_MSR_RI) + ret |= TIOCM_RNG; + if (status & UART_MSR_DSR) + ret |= TIOCM_DSR; + if (status & UART_MSR_CTS) + ret |= TIOCM_CTS; + return ret; +} + +void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned char mcr = 0; + + if (mctrl & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (mctrl & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (mctrl & TIOCM_OUT1) + mcr |= UART_MCR_OUT1; + if (mctrl & TIOCM_OUT2) + mcr |= UART_MCR_OUT2; + if (mctrl & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr; + + serial_port_out(port, UART_MCR, mcr); +} +EXPORT_SYMBOL_GPL(serial8250_do_set_mctrl); + +static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + if (port->set_mctrl) + port->set_mctrl(port, mctrl); + else + serial8250_do_set_mctrl(port, mctrl); +} + +static void serial8250_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + + serial8250_rpm_get(up); + spin_lock_irqsave(&port->lock, flags); + if (break_state == -1) + up->lcr |= UART_LCR_SBC; + else + up->lcr &= ~UART_LCR_SBC; + serial_port_out(port, UART_LCR, up->lcr); + spin_unlock_irqrestore(&port->lock, flags); + serial8250_rpm_put(up); +} + +/* + * Wait for transmitter & holding register to empty + */ +static void wait_for_xmitr(struct uart_8250_port *up, int bits) +{ + unsigned int status, tmout = 10000; + + /* Wait up to 10ms for the character(s) to be sent. */ + for (;;) { + status = serial_in(up, UART_LSR); + + up->lsr_saved_flags |= status & LSR_SAVE_FLAGS; + + if ((status & bits) == bits) + break; + if (--tmout == 0) + break; + udelay(1); + } + + /* Wait up to 1s for flow control if necessary */ + if (up->port.flags & UPF_CONS_FLOW) { + unsigned int tmout; + for (tmout = 1000000; tmout; tmout--) { + unsigned int msr = serial_in(up, UART_MSR); + up->msr_saved_flags |= msr & MSR_SAVE_FLAGS; + if (msr & UART_MSR_CTS) + break; + udelay(1); + touch_nmi_watchdog(); + } + } +} + +#ifdef CONFIG_CONSOLE_POLL +/* + * Console polling routines for writing and reading from the uart while + * in an interrupt or debug context. + */ + +static int serial8250_get_poll_char(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned char lsr; + int status; + + serial8250_rpm_get(up); + + lsr = serial_port_in(port, UART_LSR); + + if (!(lsr & UART_LSR_DR)) { + status = NO_POLL_CHAR; + goto out; + } + + status = serial_port_in(port, UART_RX); +out: + serial8250_rpm_put(up); + return status; +} + + +static void serial8250_put_poll_char(struct uart_port *port, + unsigned char c) +{ + unsigned int ier; + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get(up); + /* + * First save the IER then disable the interrupts + */ + ier = serial_port_in(port, UART_IER); + if (up->capabilities & UART_CAP_UUE) + serial_port_out(port, UART_IER, UART_IER_UUE); + else + serial_port_out(port, UART_IER, 0); + + wait_for_xmitr(up, BOTH_EMPTY); + /* + * Send the character out. + */ + serial_port_out(port, UART_TX, c); + + /* + * Finally, wait for transmitter to become empty + * and restore the IER + */ + wait_for_xmitr(up, BOTH_EMPTY); + serial_port_out(port, UART_IER, ier); + serial8250_rpm_put(up); +} + +#endif /* CONFIG_CONSOLE_POLL */ + +int serial8250_do_startup(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + unsigned char lsr, iir; + int retval; + + if (port->type == PORT_8250_CIR) + return -ENODEV; + + if (!port->fifosize) + port->fifosize = uart_config[port->type].fifo_size; + if (!up->tx_loadsz) + up->tx_loadsz = uart_config[port->type].tx_loadsz; + if (!up->capabilities) + up->capabilities = uart_config[port->type].flags; + up->mcr = 0; + + if (port->iotype != up->cur_iotype) + set_io_from_upio(port); + + serial8250_rpm_get(up); + if (port->type == PORT_16C950) { + /* Wake up and initialize UART */ + up->acr = 0; + serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); + serial_port_out(port, UART_EFR, UART_EFR_ECB); + serial_port_out(port, UART_IER, 0); + serial_port_out(port, UART_LCR, 0); + serial_icr_write(up, UART_CSR, 0); /* Reset the UART */ + serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); + serial_port_out(port, UART_EFR, UART_EFR_ECB); + serial_port_out(port, UART_LCR, 0); + } + +#ifdef CONFIG_SERIAL_8250_RSA + /* + * If this is an RSA port, see if we can kick it up to the + * higher speed clock. + */ + enable_rsa(up); +#endif + + if (port->type == PORT_XR17V35X) { + /* + * First enable access to IER [7:5], ISR [5:4], FCR [5:4], + * MCR [7:5] and MSR [7:0] + */ + serial_port_out(port, UART_XR_EFR, UART_EFR_ECB); + + /* + * Make sure all interrups are masked until initialization is + * complete and the FIFOs are cleared + */ + serial_port_out(port, UART_IER, 0); + } + + /* + * Clear the FIFO buffers and disable them. + * (they will be reenabled in set_termios()) + */ + serial8250_clear_fifos(up); + + /* + * Clear the interrupt registers. + */ + serial_port_in(port, UART_LSR); + serial_port_in(port, UART_RX); + serial_port_in(port, UART_IIR); + serial_port_in(port, UART_MSR); + + /* + * At this point, there's no way the LSR could still be 0xff; + * if it is, then bail out, because there's likely no UART + * here. + */ + if (!(port->flags & UPF_BUGGY_UART) && + (serial_port_in(port, UART_LSR) == 0xff)) { + printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n", + serial_index(port)); + retval = -ENODEV; + goto out; + } + + /* + * For a XR16C850, we need to set the trigger levels + */ + if (port->type == PORT_16850) { + unsigned char fctr; + + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + + fctr = serial_in(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX); + serial_port_out(port, UART_FCTR, + fctr | UART_FCTR_TRGD | UART_FCTR_RX); + serial_port_out(port, UART_TRG, UART_TRG_96); + serial_port_out(port, UART_FCTR, + fctr | UART_FCTR_TRGD | UART_FCTR_TX); + serial_port_out(port, UART_TRG, UART_TRG_96); + + serial_port_out(port, UART_LCR, 0); + } + + if (port->irq) { + unsigned char iir1; + /* + * Test for UARTs that do not reassert THRE when the + * transmitter is idle and the interrupt has already + * been cleared. Real 16550s should always reassert + * this interrupt whenever the transmitter is idle and + * the interrupt is enabled. Delays are necessary to + * allow register changes to become visible. + */ + spin_lock_irqsave(&port->lock, flags); + if (up->port.irqflags & IRQF_SHARED) + disable_irq_nosync(port->irq); + + wait_for_xmitr(up, UART_LSR_THRE); + serial_port_out_sync(port, UART_IER, UART_IER_THRI); + udelay(1); /* allow THRE to set */ + iir1 = serial_port_in(port, UART_IIR); + serial_port_out(port, UART_IER, 0); + serial_port_out_sync(port, UART_IER, UART_IER_THRI); + udelay(1); /* allow a working UART time to re-assert THRE */ + iir = serial_port_in(port, UART_IIR); + serial_port_out(port, UART_IER, 0); + + if (port->irqflags & IRQF_SHARED) + enable_irq(port->irq); + spin_unlock_irqrestore(&port->lock, flags); + + /* + * If the interrupt is not reasserted, or we otherwise + * don't trust the iir, setup a timer to kick the UART + * on a regular basis. + */ + if ((!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) || + up->port.flags & UPF_BUG_THRE) { + up->bugs |= UART_BUG_THRE; + } + } + + retval = up->ops->setup_irq(up); + if (retval) + goto out; + + /* + * Now, initialize the UART + */ + serial_port_out(port, UART_LCR, UART_LCR_WLEN8); + + spin_lock_irqsave(&port->lock, flags); + if (up->port.flags & UPF_FOURPORT) { + if (!up->port.irq) + up->port.mctrl |= TIOCM_OUT1; + } else + /* + * Most PC uarts need OUT2 raised to enable interrupts. + */ + if (port->irq) + up->port.mctrl |= TIOCM_OUT2; + + serial8250_set_mctrl(port, port->mctrl); + + /* Serial over Lan (SoL) hack: + Intel 8257x Gigabit ethernet chips have a + 16550 emulation, to be used for Serial Over Lan. + Those chips take a longer time than a normal + serial device to signalize that a transmission + data was queued. Due to that, the above test generally + fails. One solution would be to delay the reading of + iir. However, this is not reliable, since the timeout + is variable. So, let's just don't test if we receive + TX irq. This way, we'll never enable UART_BUG_TXEN. + */ + if (up->port.flags & UPF_NO_TXEN_TEST) + goto dont_test_tx_en; + + /* + * Do a quick test to see if we receive an + * interrupt when we enable the TX irq. + */ + serial_port_out(port, UART_IER, UART_IER_THRI); + lsr = serial_port_in(port, UART_LSR); + iir = serial_port_in(port, UART_IIR); + serial_port_out(port, UART_IER, 0); + + if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) { + if (!(up->bugs & UART_BUG_TXEN)) { + up->bugs |= UART_BUG_TXEN; + pr_debug("ttyS%d - enabling bad tx status workarounds\n", + serial_index(port)); + } + } else { + up->bugs &= ~UART_BUG_TXEN; + } + +dont_test_tx_en: + spin_unlock_irqrestore(&port->lock, flags); + + /* + * Clear the interrupt registers again for luck, and clear the + * saved flags to avoid getting false values from polling + * routines or the previous session. + */ + serial_port_in(port, UART_LSR); + serial_port_in(port, UART_RX); + serial_port_in(port, UART_IIR); + serial_port_in(port, UART_MSR); + up->lsr_saved_flags = 0; + up->msr_saved_flags = 0; + + /* + * Request DMA channels for both RX and TX. + */ + if (up->dma) { + retval = serial8250_request_dma(up); + if (retval) { + pr_warn_ratelimited("ttyS%d - failed to request DMA\n", + serial_index(port)); + up->dma = NULL; + } + } + + /* + * Set the IER shadow for rx interrupts but defer actual interrupt + * enable until after the FIFOs are enabled; otherwise, an already- + * active sender can swamp the interrupt handler with "too much work". + */ + up->ier = UART_IER_RLSI | UART_IER_RDI; + + if (port->flags & UPF_FOURPORT) { + unsigned int icp; + /* + * Enable interrupts on the AST Fourport board + */ + icp = (port->iobase & 0xfe0) | 0x01f; + outb_p(0x80, icp); + inb_p(icp); + } + retval = 0; +out: + serial8250_rpm_put(up); + return retval; +} +EXPORT_SYMBOL_GPL(serial8250_do_startup); + +static int serial8250_startup(struct uart_port *port) +{ + if (port->startup) + return port->startup(port); + return serial8250_do_startup(port); +} + +void serial8250_do_shutdown(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + + serial8250_rpm_get(up); + /* + * Disable interrupts from this port + */ + up->ier = 0; + serial_port_out(port, UART_IER, 0); + + if (up->dma) + serial8250_release_dma(up); + + spin_lock_irqsave(&port->lock, flags); + if (port->flags & UPF_FOURPORT) { + /* reset interrupts on the AST Fourport board */ + inb((port->iobase & 0xfe0) | 0x1f); + port->mctrl |= TIOCM_OUT1; + } else + port->mctrl &= ~TIOCM_OUT2; + + serial8250_set_mctrl(port, port->mctrl); + spin_unlock_irqrestore(&port->lock, flags); + + /* + * Disable break condition and FIFOs + */ + serial_port_out(port, UART_LCR, + serial_port_in(port, UART_LCR) & ~UART_LCR_SBC); + serial8250_clear_fifos(up); + +#ifdef CONFIG_SERIAL_8250_RSA + /* + * Reset the RSA board back to 115kbps compat mode. + */ + disable_rsa(up); +#endif + + /* + * Read data port to reset things, and then unlink from + * the IRQ chain. + */ + serial_port_in(port, UART_RX); + serial8250_rpm_put(up); + + up->ops->release_irq(up); +} +EXPORT_SYMBOL_GPL(serial8250_do_shutdown); + +static void serial8250_shutdown(struct uart_port *port) +{ + if (port->shutdown) + port->shutdown(port); + else + serial8250_do_shutdown(port); +} + +/* + * XR17V35x UARTs have an extra fractional divisor register (DLD) + * Calculate divisor with extra 4-bit fractional portion + */ +static unsigned int xr17v35x_get_divisor(struct uart_8250_port *up, + unsigned int baud, + unsigned int *frac) +{ + struct uart_port *port = &up->port; + unsigned int quot_16; + + quot_16 = DIV_ROUND_CLOSEST(port->uartclk, baud); + *frac = quot_16 & 0x0f; + + return quot_16 >> 4; +} + +static unsigned int serial8250_get_divisor(struct uart_8250_port *up, + unsigned int baud, + unsigned int *frac) +{ + struct uart_port *port = &up->port; + unsigned int quot; + + /* + * Handle magic divisors for baud rates above baud_base on + * SMSC SuperIO chips. + * + */ + if ((port->flags & UPF_MAGIC_MULTIPLIER) && + baud == (port->uartclk/4)) + quot = 0x8001; + else if ((port->flags & UPF_MAGIC_MULTIPLIER) && + baud == (port->uartclk/8)) + quot = 0x8002; + else if (up->port.type == PORT_XR17V35X) + quot = xr17v35x_get_divisor(up, baud, frac); + else + quot = uart_get_divisor(port, baud); + + /* + * Oxford Semi 952 rev B workaround + */ + if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0) + quot++; + + return quot; +} + +static unsigned char serial8250_compute_lcr(struct uart_8250_port *up, + tcflag_t c_cflag) +{ + unsigned char cval; + + switch (c_cflag & CSIZE) { + case CS5: + cval = UART_LCR_WLEN5; + break; + case CS6: + cval = UART_LCR_WLEN6; + break; + case CS7: + cval = UART_LCR_WLEN7; + break; + default: + case CS8: + cval = UART_LCR_WLEN8; + break; + } + + if (c_cflag & CSTOPB) + cval |= UART_LCR_STOP; + if (c_cflag & PARENB) { + cval |= UART_LCR_PARITY; + if (up->bugs & UART_BUG_PARITY) + up->fifo_bug = true; + } + if (!(c_cflag & PARODD)) + cval |= UART_LCR_EPAR; +#ifdef CMSPAR + if (c_cflag & CMSPAR) + cval |= UART_LCR_SPAR; +#endif + + return cval; +} + +static void serial8250_set_divisor(struct uart_port *port, unsigned int baud, + unsigned int quot, unsigned int quot_frac) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + /* Workaround to enable 115200 baud on OMAP1510 internal ports */ + if (is_omap1510_8250(up)) { + if (baud == 115200) { + quot = 1; + serial_port_out(port, UART_OMAP_OSC_12M_SEL, 1); + } else + serial_port_out(port, UART_OMAP_OSC_12M_SEL, 0); + } + + /* + * For NatSemi, switch to bank 2 not bank 1, to avoid resetting EXCR2, + * otherwise just set DLAB + */ + if (up->capabilities & UART_NATSEMI) + serial_port_out(port, UART_LCR, 0xe0); + else + serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB); + + serial_dl_write(up, quot); + + /* XR17V35x UARTs have an extra fractional divisor register (DLD) */ + if (up->port.type == PORT_XR17V35X) + serial_port_out(port, 0x2, quot_frac); +} + +void +serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned char cval; + unsigned long flags; + unsigned int baud, quot, frac = 0; + + cval = serial8250_compute_lcr(up, termios->c_cflag); + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, + port->uartclk / 16 / 0xffff, + port->uartclk / 16); + quot = serial8250_get_divisor(up, baud, &frac); + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + serial8250_rpm_get(up); + spin_lock_irqsave(&port->lock, flags); + + up->lcr = cval; /* Save computed LCR */ + + if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) { + /* NOTE: If fifo_bug is not set, a user can set RX_trigger. */ + if ((baud < 2400 && !up->dma) || up->fifo_bug) { + up->fcr &= ~UART_FCR_TRIGGER_MASK; + up->fcr |= UART_FCR_TRIGGER_1; + } + } + + /* + * MCR-based auto flow control. When AFE is enabled, RTS will be + * deasserted when the receive FIFO contains more characters than + * the trigger, or the MCR RTS bit is cleared. In the case where + * the remote UART is not using CTS auto flow control, we must + * have sufficient FIFO entries for the latency of the remote + * UART to respond. IOW, at least 32 bytes of FIFO. + */ + if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) { + up->mcr &= ~UART_MCR_AFE; + if (termios->c_cflag & CRTSCTS) + up->mcr |= UART_MCR_AFE; + } + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; + if (termios->c_iflag & INPCK) + port->read_status_mask |= UART_LSR_FE | UART_LSR_PE; + if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) + port->read_status_mask |= UART_LSR_BI; + + /* + * Characteres to ignore + */ + port->ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; + if (termios->c_iflag & IGNBRK) { + port->ignore_status_mask |= UART_LSR_BI; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= UART_LSR_OE; + } + + /* + * ignore all characters if CREAD is not set + */ + if ((termios->c_cflag & CREAD) == 0) + port->ignore_status_mask |= UART_LSR_DR; + + /* + * CTS flow control flag and modem status interrupts + */ + up->ier &= ~UART_IER_MSI; + if (!(up->bugs & UART_BUG_NOMSR) && + UART_ENABLE_MS(&up->port, termios->c_cflag)) + up->ier |= UART_IER_MSI; + if (up->capabilities & UART_CAP_UUE) + up->ier |= UART_IER_UUE; + if (up->capabilities & UART_CAP_RTOIE) + up->ier |= UART_IER_RTOIE; + + serial_port_out(port, UART_IER, up->ier); + + if (up->capabilities & UART_CAP_EFR) { + unsigned char efr = 0; + /* + * TI16C752/Startech hardware flow control. FIXME: + * - TI16C752 requires control thresholds to be set. + * - UART_MCR_RTS is ineffective if auto-RTS mode is enabled. + */ + if (termios->c_cflag & CRTSCTS) + efr |= UART_EFR_CTS; + + serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); + if (port->flags & UPF_EXAR_EFR) + serial_port_out(port, UART_XR_EFR, efr); + else + serial_port_out(port, UART_EFR, efr); + } + + serial8250_set_divisor(port, baud, quot, frac); + + /* + * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR + * is written without DLAB set, this mode will be disabled. + */ + if (port->type == PORT_16750) + serial_port_out(port, UART_FCR, up->fcr); + + serial_port_out(port, UART_LCR, up->lcr); /* reset DLAB */ + if (port->type != PORT_16750) { + /* emulated UARTs (Lucent Venus 167x) need two steps */ + if (up->fcr & UART_FCR_ENABLE_FIFO) + serial_port_out(port, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_port_out(port, UART_FCR, up->fcr); /* set fcr */ + } + serial8250_set_mctrl(port, port->mctrl); + spin_unlock_irqrestore(&port->lock, flags); + serial8250_rpm_put(up); + + /* Don't rewrite B0 */ + if (tty_termios_baud_rate(termios)) + tty_termios_encode_baud_rate(termios, baud, baud); +} +EXPORT_SYMBOL(serial8250_do_set_termios); + +static void +serial8250_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + if (port->set_termios) + port->set_termios(port, termios, old); + else + serial8250_do_set_termios(port, termios, old); +} + +static void +serial8250_set_ldisc(struct uart_port *port, struct ktermios *termios) +{ + if (termios->c_line == N_PPS) { + port->flags |= UPF_HARDPPS_CD; + spin_lock_irq(&port->lock); + serial8250_enable_ms(port); + spin_unlock_irq(&port->lock); + } else { + port->flags &= ~UPF_HARDPPS_CD; + if (!UART_ENABLE_MS(port, termios->c_cflag)) { + spin_lock_irq(&port->lock); + serial8250_disable_ms(port); + spin_unlock_irq(&port->lock); + } + } +} + + +void serial8250_do_pm(struct uart_port *port, unsigned int state, + unsigned int oldstate) +{ + struct uart_8250_port *p = up_to_u8250p(port); + + serial8250_set_sleep(p, state != 0); +} +EXPORT_SYMBOL(serial8250_do_pm); + +static void +serial8250_pm(struct uart_port *port, unsigned int state, + unsigned int oldstate) +{ + if (port->pm) + port->pm(port, state, oldstate); + else + serial8250_do_pm(port, state, oldstate); +} + +static unsigned int serial8250_port_size(struct uart_8250_port *pt) +{ + if (pt->port.mapsize) + return pt->port.mapsize; + if (pt->port.iotype == UPIO_AU) { + if (pt->port.type == PORT_RT2880) + return 0x100; + return 0x1000; + } + if (is_omap1_8250(pt)) + return 0x16 << pt->port.regshift; + + return 8 << pt->port.regshift; +} + +/* + * Resource handling. + */ +static int serial8250_request_std_resource(struct uart_8250_port *up) +{ + unsigned int size = serial8250_port_size(up); + struct uart_port *port = &up->port; + int ret = 0; + + switch (port->iotype) { + case UPIO_AU: + case UPIO_TSI: + case UPIO_MEM32: + case UPIO_MEM32BE: + case UPIO_MEM: + if (!port->mapbase) + break; + + if (!request_mem_region(port->mapbase, size, "serial")) { + ret = -EBUSY; + break; + } + + if (port->flags & UPF_IOREMAP) { + port->membase = ioremap_nocache(port->mapbase, size); + if (!port->membase) { + release_mem_region(port->mapbase, size); + ret = -ENOMEM; + } + } + break; + + case UPIO_HUB6: + case UPIO_PORT: + if (!request_region(port->iobase, size, "serial")) + ret = -EBUSY; + break; + } + return ret; +} + +static void serial8250_release_std_resource(struct uart_8250_port *up) +{ + unsigned int size = serial8250_port_size(up); + struct uart_port *port = &up->port; + + switch (port->iotype) { + case UPIO_AU: + case UPIO_TSI: + case UPIO_MEM32: + case UPIO_MEM32BE: + case UPIO_MEM: + if (!port->mapbase) + break; + + if (port->flags & UPF_IOREMAP) { + iounmap(port->membase); + port->membase = NULL; + } + + release_mem_region(port->mapbase, size); + break; + + case UPIO_HUB6: + case UPIO_PORT: + release_region(port->iobase, size); + break; + } +} + +static void serial8250_release_port(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_release_std_resource(up); +} + +static int serial8250_request_port(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + int ret; + + if (port->type == PORT_8250_CIR) + return -ENODEV; + + ret = serial8250_request_std_resource(up); + + return ret; +} + +static int fcr_get_rxtrig_bytes(struct uart_8250_port *up) +{ + const struct serial8250_config *conf_type = &uart_config[up->port.type]; + unsigned char bytes; + + bytes = conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(up->fcr)]; + + return bytes ? bytes : -EOPNOTSUPP; +} + +static int bytes_to_fcr_rxtrig(struct uart_8250_port *up, unsigned char bytes) +{ + const struct serial8250_config *conf_type = &uart_config[up->port.type]; + int i; + + if (!conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(UART_FCR_R_TRIG_00)]) + return -EOPNOTSUPP; + + for (i = 1; i < UART_FCR_R_TRIG_MAX_STATE; i++) { + if (bytes < conf_type->rxtrig_bytes[i]) + /* Use the nearest lower value */ + return (--i) << UART_FCR_R_TRIG_SHIFT; + } + + return UART_FCR_R_TRIG_11; +} + +static int do_get_rxtrig(struct tty_port *port) +{ + struct uart_state *state = container_of(port, struct uart_state, port); + struct uart_port *uport = state->uart_port; + struct uart_8250_port *up = + container_of(uport, struct uart_8250_port, port); + + if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1) + return -EINVAL; + + return fcr_get_rxtrig_bytes(up); +} + +static int do_serial8250_get_rxtrig(struct tty_port *port) +{ + int rxtrig_bytes; + + mutex_lock(&port->mutex); + rxtrig_bytes = do_get_rxtrig(port); + mutex_unlock(&port->mutex); + + return rxtrig_bytes; +} + +static ssize_t serial8250_get_attr_rx_trig_bytes(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct tty_port *port = dev_get_drvdata(dev); + int rxtrig_bytes; + + rxtrig_bytes = do_serial8250_get_rxtrig(port); + if (rxtrig_bytes < 0) + return rxtrig_bytes; + + return snprintf(buf, PAGE_SIZE, "%d\n", rxtrig_bytes); +} + +static int do_set_rxtrig(struct tty_port *port, unsigned char bytes) +{ + struct uart_state *state = container_of(port, struct uart_state, port); + struct uart_port *uport = state->uart_port; + struct uart_8250_port *up = + container_of(uport, struct uart_8250_port, port); + int rxtrig; + + if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 || + up->fifo_bug) + return -EINVAL; + + rxtrig = bytes_to_fcr_rxtrig(up, bytes); + if (rxtrig < 0) + return rxtrig; + + serial8250_clear_fifos(up); + up->fcr &= ~UART_FCR_TRIGGER_MASK; + up->fcr |= (unsigned char)rxtrig; + serial_out(up, UART_FCR, up->fcr); + return 0; +} + +static int do_serial8250_set_rxtrig(struct tty_port *port, unsigned char bytes) +{ + int ret; + + mutex_lock(&port->mutex); + ret = do_set_rxtrig(port, bytes); + mutex_unlock(&port->mutex); + + return ret; +} + +static ssize_t serial8250_set_attr_rx_trig_bytes(struct device *dev, + struct device_attribute *attr, const char *buf, size_t count) +{ + struct tty_port *port = dev_get_drvdata(dev); + unsigned char bytes; + int ret; + + if (!count) + return -EINVAL; + + ret = kstrtou8(buf, 10, &bytes); + if (ret < 0) + return ret; + + ret = do_serial8250_set_rxtrig(port, bytes); + if (ret < 0) + return ret; + + return count; +} + +static DEVICE_ATTR(rx_trig_bytes, S_IRUSR | S_IWUSR | S_IRGRP, + serial8250_get_attr_rx_trig_bytes, + serial8250_set_attr_rx_trig_bytes); + +static struct attribute *serial8250_dev_attrs[] = { + &dev_attr_rx_trig_bytes.attr, + NULL, + }; + +static struct attribute_group serial8250_dev_attr_group = { + .attrs = serial8250_dev_attrs, + }; + +static void register_dev_spec_attr_grp(struct uart_8250_port *up) +{ + const struct serial8250_config *conf_type = &uart_config[up->port.type]; + + if (conf_type->rxtrig_bytes[0]) + up->port.attr_group = &serial8250_dev_attr_group; +} + +static void serial8250_config_port(struct uart_port *port, int flags) +{ + struct uart_8250_port *up = up_to_u8250p(port); + int ret; + + if (port->type == PORT_8250_CIR) + return; + + /* + * Find the region that we can probe for. This in turn + * tells us whether we can probe for the type of port. + */ + ret = serial8250_request_std_resource(up); + if (ret < 0) + return; + + if (port->iotype != up->cur_iotype) + set_io_from_upio(port); + + if (flags & UART_CONFIG_TYPE) + autoconfig(up); + + /* if access method is AU, it is a 16550 with a quirk */ + if (port->type == PORT_16550A && port->iotype == UPIO_AU) + up->bugs |= UART_BUG_NOMSR; + + /* HW bugs may trigger IRQ while IIR == NO_INT */ + if (port->type == PORT_TEGRA) + up->bugs |= UART_BUG_NOMSR; + + if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ) + autoconfig_irq(up); + + if (port->type == PORT_UNKNOWN) + serial8250_release_std_resource(up); + + /* Fixme: probably not the best place for this */ + if ((port->type == PORT_XR17V35X) || + (port->type == PORT_XR17D15X)) + port->handle_irq = exar_handle_irq; + + register_dev_spec_attr_grp(up); + up->fcr = uart_config[up->port.type].fcr; +} + +static int +serial8250_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + if (ser->irq >= nr_irqs || ser->irq < 0 || + ser->baud_base < 9600 || ser->type < PORT_UNKNOWN || + ser->type >= ARRAY_SIZE(uart_config) || ser->type == PORT_CIRRUS || + ser->type == PORT_STARTECH) + return -EINVAL; + return 0; +} + +static const char * +serial8250_type(struct uart_port *port) +{ + int type = port->type; + + if (type >= ARRAY_SIZE(uart_config)) + type = 0; + return uart_config[type].name; +} + +static const struct uart_ops serial8250_pops = { + .tx_empty = serial8250_tx_empty, + .set_mctrl = serial8250_set_mctrl, + .get_mctrl = serial8250_get_mctrl, + .stop_tx = serial8250_stop_tx, + .start_tx = serial8250_start_tx, + .throttle = serial8250_throttle, + .unthrottle = serial8250_unthrottle, + .stop_rx = serial8250_stop_rx, + .enable_ms = serial8250_enable_ms, + .break_ctl = serial8250_break_ctl, + .startup = serial8250_startup, + .shutdown = serial8250_shutdown, + .set_termios = serial8250_set_termios, + .set_ldisc = serial8250_set_ldisc, + .pm = serial8250_pm, + .type = serial8250_type, + .release_port = serial8250_release_port, + .request_port = serial8250_request_port, + .config_port = serial8250_config_port, + .verify_port = serial8250_verify_port, +#ifdef CONFIG_CONSOLE_POLL + .poll_get_char = serial8250_get_poll_char, + .poll_put_char = serial8250_put_poll_char, +#endif +}; + +void serial8250_init_port(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + + spin_lock_init(&port->lock); + port->ops = &serial8250_pops; + + up->cur_iotype = 0xFF; +} +EXPORT_SYMBOL_GPL(serial8250_init_port); + +void serial8250_set_defaults(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + + if (up->port.flags & UPF_FIXED_TYPE) { + unsigned int type = up->port.type; + + if (!up->port.fifosize) + up->port.fifosize = uart_config[type].fifo_size; + if (!up->tx_loadsz) + up->tx_loadsz = uart_config[type].tx_loadsz; + if (!up->capabilities) + up->capabilities = uart_config[type].flags; + } + + set_io_from_upio(port); + + /* default dma handlers */ + if (up->dma) { + if (!up->dma->tx_dma) + up->dma->tx_dma = serial8250_tx_dma; + if (!up->dma->rx_dma) + up->dma->rx_dma = serial8250_rx_dma; + } +} +EXPORT_SYMBOL_GPL(serial8250_set_defaults); + +#ifdef CONFIG_SERIAL_8250_CONSOLE + +static void serial8250_console_putchar(struct uart_port *port, int ch) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + wait_for_xmitr(up, UART_LSR_THRE); + serial_port_out(port, UART_TX, ch); +} + +/* + * Print a string to the serial port trying not to disturb + * any possible real use of the port... + * + * The console_lock must be held when we get here. + */ +void serial8250_console_write(struct uart_8250_port *up, const char *s, + unsigned int count) +{ + struct uart_port *port = &up->port; + unsigned long flags; + unsigned int ier; + int locked = 1; + + touch_nmi_watchdog(); + + serial8250_rpm_get(up); + + if (port->sysrq) + locked = 0; + else if (oops_in_progress) + locked = spin_trylock_irqsave(&port->lock, flags); + else + spin_lock_irqsave(&port->lock, flags); + + /* + * First save the IER then disable the interrupts + */ + ier = serial_port_in(port, UART_IER); + + if (up->capabilities & UART_CAP_UUE) + serial_port_out(port, UART_IER, UART_IER_UUE); + else + serial_port_out(port, UART_IER, 0); + + /* check scratch reg to see if port powered off during system sleep */ + if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) { + struct ktermios termios; + unsigned int baud, quot, frac = 0; + + termios.c_cflag = port->cons->cflag; + if (port->state->port.tty && termios.c_cflag == 0) + termios.c_cflag = port->state->port.tty->termios.c_cflag; + + baud = uart_get_baud_rate(port, &termios, NULL, + port->uartclk / 16 / 0xffff, + port->uartclk / 16); + quot = serial8250_get_divisor(up, baud, &frac); + + serial8250_set_divisor(port, baud, quot, frac); + serial_port_out(port, UART_LCR, up->lcr); + serial_port_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS); + + up->canary = 0; + } + + uart_console_write(port, s, count, serial8250_console_putchar); + + /* + * Finally, wait for transmitter to become empty + * and restore the IER + */ + wait_for_xmitr(up, BOTH_EMPTY); + serial_port_out(port, UART_IER, ier); + + /* + * The receive handling will happen properly because the + * receive ready bit will still be set; it is not cleared + * on read. However, modem control will not, we must + * call it if we have saved something in the saved flags + * while processing with interrupts off. + */ + if (up->msr_saved_flags) + serial8250_modem_status(up); + + if (locked) + spin_unlock_irqrestore(&port->lock, flags); + serial8250_rpm_put(up); +} + +static unsigned int probe_baud(struct uart_port *port) +{ + unsigned char lcr, dll, dlm; + unsigned int quot; + + lcr = serial_port_in(port, UART_LCR); + serial_port_out(port, UART_LCR, lcr | UART_LCR_DLAB); + dll = serial_port_in(port, UART_DLL); + dlm = serial_port_in(port, UART_DLM); + serial_port_out(port, UART_LCR, lcr); + + quot = (dlm << 8) | dll; + return (port->uartclk / 16) / quot; +} + +int serial8250_console_setup(struct uart_port *port, char *options, bool probe) +{ + int baud = 9600; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + if (!port->iobase && !port->membase) + return -ENODEV; + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + else if (probe) + baud = probe_baud(port); + + return uart_set_options(port, port->cons, baud, parity, bits, flow); +} + +#endif /* CONFIG_SERIAL_8250_CONSOLE */ |